diff mbox series

[RFC,net-next,v2,08/12] net: ethernet: freescale: xgmac: Separate C22 and C45 transactions for xgmac

Message ID 20221227-v6-2-rc1-c45-seperation-v2-8-ddb37710e5a7@walle.cc
State New
Headers
Series net: mdio: Start separating C22 and C45 |

Commit Message

Michael Walle Dec. 27, 2022, 11:07 p.m. UTC 
  From: Andrew Lunn <andrew@lunn.ch>

The xgmac MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
---
v2:
 - [al] Move the masking of regnum into the variable declarations
 - [al] Remove a couple of blank lines
---
 drivers/net/ethernet/freescale/xgmac_mdio.c | 150 +++++++++++++++++++++-------
 1 file changed, 113 insertions(+), 37 deletions(-)

Comments

Vladimir Oltean Jan. 3, 2023, 1:55 p.m. UTC | #1 
Commit message can be: "net/fsl: xgmac_mdio: Separate C22 and C45 transactions".

On Wed, Dec 28, 2022 at 12:07:24AM +0100, Michael Walle wrote:
> From: Andrew Lunn <andrew@lunn.ch>
> 
> The xgmac MDIO bus driver can perform both C22 and C45 transfers.
> Create separate functions for each and register the C45 versions using
> the new API calls where appropriate.
> 
> Signed-off-by: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Michael Walle <michael@walle.cc>
> ---
> v2:
>  - [al] Move the masking of regnum into the variable declarations
>  - [al] Remove a couple of blank lines

Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>

>  
> -/*
> - * Reads from register regnum in the PHY for device dev, returning the value.
> +/* Reads from register regnum in the PHY for device dev, returning the value.
>   * Clears miimcom first.  All PHY configuration has to be done through the
>   * TSEC1 MIIM regs.
>   */

I have some reservations regarding the utility of the comments in this
driver. It's surely not worth duplicating them between C22 and C45.
It might also be more productive to just delete them, because:

 - miimcom is a register accessed by fsl_pq_mdio.c, not by xgmac_mdio.c
 - "device dev" doesn't really refer to anything (maybe "dev_addr").
 - I don't understand what is meant by the comment "All PHY configuration
   has to be done through the TSEC1 MIIM regs". Or rather said, I think I
   understand, but it is irrelevant to the driver for 2 reasons:
    * TSEC devices use the fsl_pq_mdio.c driver, not this one
    * It doesn't matter to this driver whose TSEC registers are used for
      MDIO access. The driver just works with the registers it's given,
      which is a concern for the device tree.
 - barring the above, the rest just describes the MDIO bus API, which is
   superfluous
diff mbox series

Patch

diff --git a/drivers/net/ethernet/freescale/xgmac_mdio.c b/drivers/net/ethernet/freescale/xgmac_mdio.c
index d7d39a58cd80..1861cf14f4d7 100644
--- a/drivers/net/ethernet/freescale/xgmac_mdio.c
+++ b/drivers/net/ethernet/freescale/xgmac_mdio.c
@@ -128,30 +128,57 @@  static int xgmac_wait_until_done(struct device *dev,
 	return 0;
 }
 
-/*
- * Write value to the PHY for this device to the register at regnum,waiting
+/* Write value to the PHY for this device to the register at regnum,waiting
  * until the write is done before it returns.  All PHY configuration has to be
  * done through the TSEC1 MIIM regs.
  */
-static int xgmac_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 value)
+static int xgmac_mdio_write_c22(struct mii_bus *bus, int phy_id, int regnum,
+				u16 value)
 {
 	struct mdio_fsl_priv *priv = (struct mdio_fsl_priv *)bus->priv;
 	struct tgec_mdio_controller __iomem *regs = priv->mdio_base;
-	uint16_t dev_addr;
+	bool endian = priv->is_little_endian;
+	u16 dev_addr = regnum & 0x1f;
 	u32 mdio_ctl, mdio_stat;
 	int ret;
+
+	mdio_stat = xgmac_read32(&regs->mdio_stat, endian);
+	mdio_stat &= ~MDIO_STAT_ENC;
+	xgmac_write32(mdio_stat, &regs->mdio_stat, endian);
+
+	ret = xgmac_wait_until_free(&bus->dev, regs, endian);
+	if (ret)
+		return ret;
+
+	/* Set the port and dev addr */
+	mdio_ctl = MDIO_CTL_PORT_ADDR(phy_id) | MDIO_CTL_DEV_ADDR(dev_addr);
+	xgmac_write32(mdio_ctl, &regs->mdio_ctl, endian);
+
+	/* Write the value to the register */
+	xgmac_write32(MDIO_DATA(value), &regs->mdio_data, endian);
+
+	ret = xgmac_wait_until_done(&bus->dev, regs, endian);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+/* Write value to the PHY for this device to the register at regnum,waiting
+ * until the write is done before it returns.  All PHY configuration has to be
+ * done through the TSEC1 MIIM regs.
+ */
+static int xgmac_mdio_write_c45(struct mii_bus *bus, int phy_id, int dev_addr,
+				int regnum, u16 value)
+{
+	struct mdio_fsl_priv *priv = (struct mdio_fsl_priv *)bus->priv;
+	struct tgec_mdio_controller __iomem *regs = priv->mdio_base;
 	bool endian = priv->is_little_endian;
+	u32 mdio_ctl, mdio_stat;
+	int ret;
 
 	mdio_stat = xgmac_read32(&regs->mdio_stat, endian);
-	if (regnum & MII_ADDR_C45) {
-		/* Clause 45 (ie 10G) */
-		dev_addr = (regnum >> 16) & 0x1f;
-		mdio_stat |= MDIO_STAT_ENC;
-	} else {
-		/* Clause 22 (ie 1G) */
-		dev_addr = regnum & 0x1f;
-		mdio_stat &= ~MDIO_STAT_ENC;
-	}
+	mdio_stat |= MDIO_STAT_ENC;
 
 	xgmac_write32(mdio_stat, &regs->mdio_stat, endian);
 
@@ -164,13 +191,11 @@  static int xgmac_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 val
 	xgmac_write32(mdio_ctl, &regs->mdio_ctl, endian);
 
 	/* Set the register address */
-	if (regnum & MII_ADDR_C45) {
-		xgmac_write32(regnum & 0xffff, &regs->mdio_addr, endian);
+	xgmac_write32(regnum & 0xffff, &regs->mdio_addr, endian);
 
-		ret = xgmac_wait_until_free(&bus->dev, regs, endian);
-		if (ret)
-			return ret;
-	}
+	ret = xgmac_wait_until_free(&bus->dev, regs, endian);
+	if (ret)
+		return ret;
 
 	/* Write the value to the register */
 	xgmac_write32(MDIO_DATA(value), &regs->mdio_data, endian);
@@ -182,31 +207,82 @@  static int xgmac_mdio_write(struct mii_bus *bus, int phy_id, int regnum, u16 val
 	return 0;
 }
 
-/*
- * Reads from register regnum in the PHY for device dev, returning the value.
+/* Reads from register regnum in the PHY for device dev, returning the value.
  * Clears miimcom first.  All PHY configuration has to be done through the
  * TSEC1 MIIM regs.
  */
-static int xgmac_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
+static int xgmac_mdio_read_c22(struct mii_bus *bus, int phy_id, int regnum)
 {
 	struct mdio_fsl_priv *priv = (struct mdio_fsl_priv *)bus->priv;
 	struct tgec_mdio_controller __iomem *regs = priv->mdio_base;
+	bool endian = priv->is_little_endian;
+	u16 dev_addr = regnum & 0x1f;
 	unsigned long flags;
-	uint16_t dev_addr;
 	uint32_t mdio_stat;
 	uint32_t mdio_ctl;
 	int ret;
-	bool endian = priv->is_little_endian;
 
 	mdio_stat = xgmac_read32(&regs->mdio_stat, endian);
-	if (regnum & MII_ADDR_C45) {
-		dev_addr = (regnum >> 16) & 0x1f;
-		mdio_stat |= MDIO_STAT_ENC;
+	mdio_stat &= ~MDIO_STAT_ENC;
+	xgmac_write32(mdio_stat, &regs->mdio_stat, endian);
+
+	ret = xgmac_wait_until_free(&bus->dev, regs, endian);
+	if (ret)
+		return ret;
+
+	/* Set the Port and Device Addrs */
+	mdio_ctl = MDIO_CTL_PORT_ADDR(phy_id) | MDIO_CTL_DEV_ADDR(dev_addr);
+	xgmac_write32(mdio_ctl, &regs->mdio_ctl, endian);
+
+	if (priv->has_a009885)
+		/* Once the operation completes, i.e. MDIO_STAT_BSY clears, we
+		 * must read back the data register within 16 MDC cycles.
+		 */
+		local_irq_save(flags);
+
+	/* Initiate the read */
+	xgmac_write32(mdio_ctl | MDIO_CTL_READ, &regs->mdio_ctl, endian);
+
+	ret = xgmac_wait_until_done(&bus->dev, regs, endian);
+	if (ret)
+		goto irq_restore;
+
+	/* Return all Fs if nothing was there */
+	if ((xgmac_read32(&regs->mdio_stat, endian) & MDIO_STAT_RD_ER) &&
+	    !priv->has_a011043) {
+		dev_dbg(&bus->dev,
+			"Error while reading PHY%d reg at %d.%d\n",
+			phy_id, dev_addr, regnum);
+		ret = 0xffff;
 	} else {
-		dev_addr = regnum & 0x1f;
-		mdio_stat &= ~MDIO_STAT_ENC;
+		ret = xgmac_read32(&regs->mdio_data, endian) & 0xffff;
+		dev_dbg(&bus->dev, "read %04x\n", ret);
 	}
 
+irq_restore:
+	if (priv->has_a009885)
+		local_irq_restore(flags);
+
+	return ret;
+}
+
+/* Reads from register regnum in the PHY for device dev, returning the value.
+ * Clears miimcom first.  All PHY configuration has to be done through the
+ * TSEC1 MIIM regs.
+ */
+static int xgmac_mdio_read_c45(struct mii_bus *bus, int phy_id, int dev_addr,
+			       int regnum)
+{
+	struct mdio_fsl_priv *priv = (struct mdio_fsl_priv *)bus->priv;
+	struct tgec_mdio_controller __iomem *regs = priv->mdio_base;
+	bool endian = priv->is_little_endian;
+	u32 mdio_stat, mdio_ctl;
+	unsigned long flags;
+	int ret;
+
+	mdio_stat = xgmac_read32(&regs->mdio_stat, endian);
+	mdio_stat |= MDIO_STAT_ENC;
+
 	xgmac_write32(mdio_stat, &regs->mdio_stat, endian);
 
 	ret = xgmac_wait_until_free(&bus->dev, regs, endian);
@@ -218,13 +294,11 @@  static int xgmac_mdio_read(struct mii_bus *bus, int phy_id, int regnum)
 	xgmac_write32(mdio_ctl, &regs->mdio_ctl, endian);
 
 	/* Set the register address */
-	if (regnum & MII_ADDR_C45) {
-		xgmac_write32(regnum & 0xffff, &regs->mdio_addr, endian);
+	xgmac_write32(regnum & 0xffff, &regs->mdio_addr, endian);
 
-		ret = xgmac_wait_until_free(&bus->dev, regs, endian);
-		if (ret)
-			return ret;
-	}
+	ret = xgmac_wait_until_free(&bus->dev, regs, endian);
+	if (ret)
+		return ret;
 
 	if (priv->has_a009885)
 		/* Once the operation completes, i.e. MDIO_STAT_BSY clears, we
@@ -326,8 +400,10 @@  static int xgmac_mdio_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	bus->name = "Freescale XGMAC MDIO Bus";
-	bus->read = xgmac_mdio_read;
-	bus->write = xgmac_mdio_write;
+	bus->read = xgmac_mdio_read_c22;
+	bus->write = xgmac_mdio_write_c22;
+	bus->read_c45 = xgmac_mdio_read_c45;
+	bus->write_c45 = xgmac_mdio_write_c45;
 	bus->parent = &pdev->dev;
 	bus->probe_capabilities = MDIOBUS_C22_C45;
 	snprintf(bus->id, MII_BUS_ID_SIZE, "%pa", &res->start);