diff mbox series

[v3,1/4] arm64: dts: qcom: sc7180: Bump up trogdor ts_reset_l drive strength

Message ID 20221209091234.v3.1.I39c387f1e3176fcf340039ec12d54047de9f8526@changeid
State New
Headers
Series arm64: dts: qcom: sc7180: Make pazquel360's touchscreen work |

Commit Message

Doug Anderson Dec. 9, 2022, 5:12 p.m. UTC 
  On at least one board (pazquel360) the reset line for the touchscreen
was scoped and found to take almost 2 ms to fall when we drove it
low. This wasn't great because the Linux driver for the touchscreen
(the elants_i2c driver) thinks it can do a 500 us reset pulse. If we
bump the drive strength to 8 mA then the reset line went down in ~421
us.

NOTE: we could apply this fix just for pazquel360, but:
* Probably other trogdor devices have similar timings and it's just
  that nobody has noticed it before.
* There are other trogdor boards using the same elan driver that tries
  to do 500 us reset pulses.
* Bumping the drive strength to 8mA across the board won't hurt. This
  isn't a high speed signal or anything.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
---

(no changes since v1)

 arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

Comments

Konrad Dybcio Dec. 10, 2022, 11:05 a.m. UTC | #1 
On 9.12.2022 18:12, Douglas Anderson wrote:
> On at least one board (pazquel360) the reset line for the touchscreen
> was scoped and found to take almost 2 ms to fall when we drove it
> low. This wasn't great because the Linux driver for the touchscreen
> (the elants_i2c driver) thinks it can do a 500 us reset pulse. If we
> bump the drive strength to 8 mA then the reset line went down in ~421
> us.
> 
> NOTE: we could apply this fix just for pazquel360, but:
> * Probably other trogdor devices have similar timings and it's just
>   that nobody has noticed it before.
> * There are other trogdor boards using the same elan driver that tries
>   to do 500 us reset pulses.
> * Bumping the drive strength to 8mA across the board won't hurt. This
>   isn't a high speed signal or anything.
> 
> Signed-off-by: Douglas Anderson <dianders@chromium.org>
> Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
> 
> (no changes since v1)
> 
>  arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 10 +++++++++-
>  1 file changed, 9 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> index f1defb94d670..ff1c7aa6a722 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
> @@ -1376,7 +1376,15 @@ ts_reset_l: ts-reset-l-state {
>  		pins = "gpio8";
>  		function = "gpio";
>  		bias-disable;
> -		drive-strength = <2>;
> +
> +		/*
> +		 * The reset GPIO to the touchscreen takes almost 2ms to drop
> +		 * at the default drive strength. When we bump it up to 8mA it
> +		 * falls in under 500us. We want this to be fast since the Elan
> +		 * datasheet (and any drivers written based on it) talk about using
> +		 * a 500 us reset pulse.
> +		 */
> +		drive-strength = <8>;
>  	};
>  
>  	sdc1_on: sdc1-on-state {
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
index f1defb94d670..ff1c7aa6a722 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
@@ -1376,7 +1376,15 @@  ts_reset_l: ts-reset-l-state {
 		pins = "gpio8";
 		function = "gpio";
 		bias-disable;
-		drive-strength = <2>;
+
+		/*
+		 * The reset GPIO to the touchscreen takes almost 2ms to drop
+		 * at the default drive strength. When we bump it up to 8mA it
+		 * falls in under 500us. We want this to be fast since the Elan
+		 * datasheet (and any drivers written based on it) talk about using
+		 * a 500 us reset pulse.
+		 */
+		drive-strength = <8>;
 	};
 
 	sdc1_on: sdc1-on-state {