[v3,6/9] arm64: dts: qcom: msm8953: Add device tree for Xiaomi Redmi Note 4X
Commit Message
From: Adam Skladowski <a39.skl@gmail.com>
Add device tree for the Xiaomi Redmi Note 4X (mido) smartphone. This
device is based on Snapdragon 625 (msm8953) SoC.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/msm8953-xiaomi-mido.dts | 329 +++++++++++++++++++++++
2 files changed, 330 insertions(+)
@@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-serranove.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-mido.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8956-sony-xperia-loire-kugo.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8956-sony-xperia-loire-suzu.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8992-lg-bullhead-rev-10.dtb
new file mode 100644
@@ -0,0 +1,329 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/dts-v1/;
+
+#include "msm8953.dtsi"
+#include "pm8953.dtsi"
+#include "pmi8950.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/delete-node/ &cont_splash_mem;
+/delete-node/ &qseecom_mem;
+
+/ {
+ model = "Xiaomi Redmi Note 4X";
+ compatible = "xiaomi,mido", "qcom,msm8953";
+ chassis-type = "handset";
+ qcom,msm-id = <293 0>;
+ qcom,board-id = <11 0>;
+
+ aliases {
+ mmc0 = &sdhc_1;
+ mmc1 = &sdhc_2;
+ };
+
+ speaker_amp: audio-amplifier {
+ compatible = "awinic,aw8738";
+ mode-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ awinic,mode = <5>;
+ sound-name-prefix = "Speaker Amp";
+ };
+
+ chosen {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ framebuffer@90001000 {
+ compatible = "simple-framebuffer";
+ reg = <0 0x90001000 0 (1920 * 1080 * 3)>;
+
+ width = <1080>;
+ height = <1920>;
+ stride = <(1080 * 3)>;
+ format = "r8g8b8";
+
+ power-domains = <&gcc MDSS_GDSC>;
+
+ clocks = <&gcc GCC_MDSS_AHB_CLK>,
+ <&gcc GCC_MDSS_AXI_CLK>,
+ <&gcc GCC_MDSS_VSYNC_CLK>,
+ <&gcc GCC_MDSS_MDP_CLK>,
+ <&gcc GCC_MDSS_BYTE0_CLK>,
+ <&gcc GCC_MDSS_PCLK0_CLK>,
+ <&gcc GCC_MDSS_ESC0_CLK>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&gpio_key_default>;
+
+ key-volume-up {
+ label = "Volume Up";
+ gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ reserved-memory {
+ qseecom_mem: qseecom@84a00000 {
+ reg = <0x0 0x84a00000 0x0 0x1900000>;
+ no-map;
+ };
+
+ cont_splash_mem: cont-splash@90001000 {
+ reg = <0x0 0x90001000 0x0 (1080 * 1920 * 3)>;
+ no-map;
+ };
+
+ ramoops@9ff00000 {
+ compatible = "ramoops";
+ reg = <0x0 0x9ff00000 0x0 0x00100000>;
+ console-size = <0x100000>;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&hsusb_phy {
+ vdd-supply = <&pm8953_l3>;
+ vdda-pll-supply = <&pm8953_l7>;
+ vdda-phy-dpdm-supply = <&pm8953_l13>;
+
+ status = "okay";
+};
+
+&i2c_2 {
+ status = "okay";
+
+ led-controller@45 {
+ compatible = "awinic,aw2013";
+ reg = <0x45>;
+
+ vcc-supply = <&pm8953_l10>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led@0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_INDICATOR;
+ led-max-microamp = <5000>;
+ };
+
+ led@1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_INDICATOR;
+ led-max-microamp = <5000>;
+ };
+
+ led@2 {
+ reg = <2>;
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_INDICATOR;
+ led-max-microamp = <5000>;
+ };
+ };
+};
+
+&i2c_3 {
+ status = "okay";
+
+ touchscreen@38 {
+ compatible = "edt,edt-ft5406";
+ reg = <0x38>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <65 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_int_active>;
+
+ reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&pm8953_l10>;
+
+ touchscreen-size-x = <1080>;
+ touchscreen-size-y = <1920>;
+ };
+};
+
+&pm8953_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&rpm_requests {
+ regulators {
+ compatible = "qcom,rpm-pm8953-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+ vdd_s7-supply = <&vph_pwr>;
+ vdd_l1-supply = <&pm8953_s3>;
+ vdd_l2_l3-supply = <&pm8953_s3>;
+ vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>;
+ vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>;
+ vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>;
+ vdd_l23-supply = <&pm8953_s3>;
+
+ pm8953_s1: s1 {
+ regulator-min-microvolt = <863000>;
+ regulator-max-microvolt = <1152000>;
+ };
+
+ pm8953_s3: s3 {
+ regulator-min-microvolt = <1224000>;
+ regulator-max-microvolt = <1224000>;
+ };
+
+ pm8953_s4: s4 {
+ regulator-min-microvolt = <1896000>;
+ regulator-max-microvolt = <2048000>;
+ };
+
+ pm8953_l1: l1 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ pm8953_l2: l2 {
+ regulator-min-microvolt = <975000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ pm8953_l3: l3 {
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <925000>;
+ regulator-allow-set-load;
+ };
+
+ pm8953_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8953_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ pm8953_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1900000>;
+ };
+
+ pm8953_l8: l8 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ pm8953_l9: l9 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ pm8953_l10: l10 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ regulator-always-on;
+ };
+
+ pm8953_l11: l11 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8953_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8953_l13: l13 {
+ regulator-min-microvolt = <3125000>;
+ regulator-max-microvolt = <3125000>;
+ };
+
+ pm8953_l16: l16 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8953_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+
+ pm8953_l19: l19 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ };
+
+ pm8953_l22: l22 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2850000>;
+ regulator-always-on;
+ };
+
+ pm8953_l23: l23 {
+ regulator-min-microvolt = <975000>;
+ regulator-max-microvolt = <1225000>;
+ };
+ };
+};
+
+&sdhc_1 {
+ vmmc-supply = <&pm8953_l8>;
+ vqmmc-supply = <&pm8953_l5>;
+
+ status = "okay";
+};
+
+&sdhc_2 {
+ vmmc-supply = <&pm8953_l11>;
+ vqmmc-supply = <&pm8953_l12>;
+
+ cd-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+ status = "okay";
+};
+
+&tlmm {
+ gpio-reserved-ranges = <0 4>, <135 4>;
+
+ ts_int_active: ts-int-active-state {
+ pins = "gpio65";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb3_dwc3 {
+ dr_mode = "peripheral";
+};