new file mode 100644
@@ -0,0 +1,274 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+=========================================
+Kernel driver for AW20036/AW20054/AW20072
+=========================================
+
+Description
+-----------
+
+The AW20036/AW20054/AW20072 is a 3x12/6x9/6x12 matrix LED driver programmed via
+an I2C interface. The brightness of each LED is independently controlled by
+FADE and DIM parameter.
+
+Three integrated pattern controllers provide auto breathing or group dimming
+control. Each pattern controller can work in auto breathing or manual control
+mode. All breathing parameters including rising/falling slope, on/off time,
+repeat times, min/max brightness and so on are configurable.
+
+Device attribute
+-----------------------------------
+
+**/sys/class/leds/<led>/dim** - 64-level DIM current. If write negative value
+or "auto", the dim will be calculated according to the brightness.
+
+The configuration files for each pattern are located::
+
+ /sys/bus/i2c/devices/xxxx/pattern0/
+ /sys/bus/i2c/devices/xxxx/pattern1/
+ /sys/bus/i2c/devices/xxxx/pattern2/
+
+Directory layout example for pattern
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+::
+
+ $ ls -l /sys/bus/i2c/devices/xxxx/pattern0/
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 clear_leds
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 fall_time
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 loop_begin
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 loop_end_on
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 max_breathing_level
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 min_breathing_level
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 mode
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 off_time
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 on_time
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 ramp
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 repeat
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 rise_time
+ -r--r--r-- 1 root root 4096 Jan 1 00:00 running
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 select_leds
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 start
+ -rw-r--r-- 1 root root 4096 Jan 1 00:00 toggle
+
+Timing parameters
+~~~~~~~~~~~~~~~~~
+
+- **on_time**
+
+- **rise_time**
+
+- **fall_time**
+
+- **off_time**
+
+See :ref:`auto_breath_mode`.
+
+Select from predefined times:
+
+.. flat-table::
+
+ * - Value
+ - Time (in seconds)
+ - Value
+ - Time (in seconds)
+
+ * - 0
+ - 0.00
+ - 8
+ - 2.1
+
+ * - 1
+ - 0.13
+ - 9
+ - 2.6
+
+ * - 2
+ - 0.26
+ - 10
+ - 3.1
+
+ * - 3
+ - 0.38
+ - 11
+ - 4.2
+
+ * - 4
+ - 0.51
+ - 12
+ - 5.2
+
+ * - 5
+ - 0.77
+ - 13
+ - 6.2
+
+ * - 6
+ - 1.04
+ - 14
+ - 7.3
+
+ * - 7
+ - 1.6
+ - 15
+ - 8.3
+
+Example set for rise-time=0.13s, on-time=0.26s,
+fall_time=6.2s, off_time=0.51s:
+
+.. code-block:: bash
+
+ echo 1 > rise_time
+ echo 2 > on_time
+ echo 13 > fall_time
+ echo 4 > off_time
+
+Maximum and minimum breathing Level
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+- **max_breathing_level**
+
+- **min_breathing_level**
+
+Loop
+~~~~~
+
+- **loop_begin** - choose where to start the loop:
+
+ .. flat-table::
+
+ * - Value
+ - Description
+
+ * - 0
+ - Begin from 'rise' state
+
+ * - 1
+ - Begin from 'on' state
+
+ * - 2
+ - Begin from 'fall' state
+
+ * - 3
+ - Begin from 'off' state
+
+- **loop_end_on** - write ``1`` loop end at 'on' state.
+
+- **repeat** - loop times. When write ``0``, the loop is end-less.
+
+Others
+~~~~~~
+
+- **clear_leds** - bitmask for clear leds to pattern.
+ For example clear leds 1, 2, 3, 4, 5, 7 (``10111110``):
+
+ .. code-block:: bash
+
+ echo be > clear_leds
+
+- **select_leds** - bitmask for set leds to pattern.
+ For example select leds 0, 3, 6, 7 (``11001001``):
+
+ .. code-block:: bash
+
+ echo c9 > select_leds
+
+- **mode** - pattern mode:
+ ``0`` - manual control, ``1`` - auto breathing
+
+- **start** - start/stop pattern:
+ ``0`` - to stop, ``1`` - to start
+
+- **toggle** - manual on/off control (see :ref:`manual_breath_mode`):
+ ``0`` - LEDs off, ``1`` - LEDs on
+
+- **ramp** - the smooth ramp up/down function (see :ref:`manual_breath_mode`):
+ ``0`` - disable, ``1`` - enable
+
+- **running** - Reading this file will return the pattern state:
+ ``1`` - is running, ``0`` - is finished (or not running)
+
+This file supports poll() to detect when the pattern finished.
+
+.. _auto_breath_mode:
+
+Auto breathing mode
+~~~~~~~~~~~~~~~~~~~
+
+::
+
+ breathing level
+ ^
+ max _ ________________
+ | /. .\
+ | / . . \
+ | / . . \
+ | / . . \
+ | / . . \
+ | / . . \
+ min _ ___/ . . \_______
+ | . . . .
+ | . . . .
+ | . rise . on . fall . off
+ |
+ -|------------------------------------------------> time
+
+Example:
+
+.. code-block:: bash
+
+ echo 10 > rise_time # 3.1 seconds
+ echo 4 > on_time # 0.51 seconds
+ echo 1 > off_time # 0.13 seconds
+ echo 10 > fall_time # 3.1 seconds
+ echo 0 > min_breathing_level
+ echo 255 > max_breathing_level
+ echo 0 > loop_begin # begin from 'rise'
+ echo 0 > loop_end_on # loop end at 'off' state
+ echo 1 > mode # auto breathing mode
+ echo 5 > repeat # 5 times repeat
+ echo 1249 > select_leds # select 0, 3, 6, 9 12 leds (1001001001001)
+ echo 1 > start # run
+
+
+.. _manual_breath_mode:
+
+Manual control mode
+~~~~~~~~~~~~~~~~~~~
+
+When 'ramp' enabled (echo 1 > ramp)::
+
+ breathing level
+ ^
+ max _ ____________________
+ | / .\
+ | / . \
+ | / . \
+ | / . \
+ | / . \
+ | / . \
+ min _ ______/ . \_______
+ | . .
+ | . .
+ | . .
+ | (echo 1 > toggle) (echo 0 > toggle)
+ -|---------------------------------------------------> time
+
+
+When 'ramp' disabled (echo 0 > ramp)::
+
+ breathing level
+ ^
+ max _ __________________________
+ | | |
+ | | |
+ | | |
+ | | |
+ | | |
+ | | |
+ min _ ______| |_______
+ | . .
+ | . .
+ | . .
+ | echo 1 > toggle echo 0 > toggle
+ -|---------------------------------------------------> time
@@ -94,6 +94,16 @@ config LEDS_ARIEL
Say Y to if your machine is a Dell Wyse 3020 thin client.
+config LEDS_AW200XX
+ tristate "LED support for Awinic AW20036/AW20054/AW20072"
+ depends on LEDS_CLASS
+ depends on I2C
+ help
+ This option enables support for the AW20036/AW20054/AW20072 LED driver.
+ It is a 3x12/6x9/6x12 matrix LED driver programmed via
+ an I2C interface, up to 36/54/72 LEDs or 12/18/24 RGBs,
+ 3 pattern controllers for auto breathing or group dimming control.
+
config LEDS_AW2013
tristate "LED support for Awinic AW2013"
depends on LEDS_CLASS && I2C && OF
@@ -15,6 +15,7 @@ obj-$(CONFIG_LEDS_AN30259A) += leds-an30259a.o
obj-$(CONFIG_LEDS_APU) += leds-apu.o
obj-$(CONFIG_LEDS_ARIEL) += leds-ariel.o
obj-$(CONFIG_LEDS_ASIC3) += leds-asic3.o
+obj-$(CONFIG_LEDS_AW200XX) += leds-aw200xx.o
obj-$(CONFIG_LEDS_AW2013) += leds-aw2013.o
obj-$(CONFIG_LEDS_BCM6328) += leds-bcm6328.o
obj-$(CONFIG_LEDS_BCM6358) += leds-bcm6358.o
new file mode 100644
@@ -0,0 +1,1113 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * leds-aw200xx.c - Awinic AW20036/AW20054/AW20072 LED driver
+ *
+ * Copyright (c) 2022, SberDevices. All Rights Reserved.
+ *
+ * Author: Martin Kurbanov <mmkurbanov@sberdevices.ru>
+ */
+
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/mutex.h>
+#include <linux/regmap.h>
+#include <linux/interrupt.h>
+#include <linux/bitfield.h>
+
+#define AW200XX_LEDS_MAX 72
+#define AW200XX_PATTERN_MAX 3
+#define AW200XX_DIM_MAX 0x3F
+#define AW200XX_FADE_MAX 0xFF
+#define AW200XX_IMAX_MAX 15
+#define AW200XX_IMAX_DEFAULT 4 /* 60mA */
+
+/* Page 0 */
+#define AW200XX_REG_PAGE0_BASE 0xc000
+
+/* Select page register */
+#define AW200XX_REG_PAGE 0xF0
+#define AW200XX_PAGE_MASK (GENMASK(7, 6) | GENMASK(2, 0))
+#define AW200XX_PAGE_SHIFT 0
+#define AW200XX_NUM_PAGES 6
+#define AW200XX_PAGE_SIZE 256
+#define AW200XX_REG(page, reg) \
+ (AW200XX_REG_PAGE0_BASE + ((page) * AW200XX_PAGE_SIZE) + (reg))
+#define AW200XX_REG_MAX \
+ AW200XX_REG(AW200XX_NUM_PAGES - 1, AW200XX_PAGE_SIZE - 1)
+#define AW200XX_PAGE0 0
+#define AW200XX_PAGE1 1
+#define AW200XX_PAGE2 2
+#define AW200XX_PAGE3 3
+#define AW200XX_PAGE4 4
+#define AW200XX_PAGE5 5
+
+/* Chip ID register */
+#define AW200XX_REG_IDR AW200XX_REG(AW200XX_PAGE0, 0x00)
+#define AW200XX_IDR_CHIPID 0x18
+
+/* Sleep mode register */
+#define AW200XX_REG_SLPCR AW200XX_REG(AW200XX_PAGE0, 0x01)
+#define AW200XX_SLPCR_ACTIVE 0x00
+
+/* Reset register */
+#define AW200XX_REG_RSTR AW200XX_REG(AW200XX_PAGE0, 0x02)
+#define AW200XX_RSTR_RESET 0x01
+
+/* Global current configuration register */
+#define AW200XX_REG_GCCR AW200XX_REG(AW200XX_PAGE0, 0x03)
+#define AW200XX_GCCR_IMAX(x) ((x) << 4)
+#define AW200XX_GCCR_ALLON BIT(3)
+
+/* Fast clear display control register */
+#define AW200XX_REG_FCD AW200XX_REG(AW200XX_PAGE0, 0x04)
+#define AW200XX_FCD_CLEAR 0x01
+
+/* Interrupt status register */
+#define AW200XX_REG_ISRFLT AW200XX_REG(AW200XX_PAGE0, 0x0B)
+#define AW200XX_ISRFLT_PATIS_MASK GENMASK(6, 4)
+
+/* Pattern enable control register */
+#define AW200XX_REG_PATCR AW200XX_REG(AW200XX_PAGE0, 0x43)
+#define AW200XX_PATCR_PAT_IE_MASK GENMASK(6, 4)
+#define AW200XX_PATCR_PAT_IE_ALL AW200XX_PATCR_PAT_IE_MASK
+#define AW200XX_PATCR_PAT_ENABLE(x) BIT(x)
+
+/*
+ * Maximum breathing level registers
+ * For patterns 0 - 0x44, 1 - 0x45, 2 - 0x46 (step 1)
+ */
+#define AW200XX_REG_PAT0_MAX_BREATH AW200XX_REG(AW200XX_PAGE0, 0x44)
+
+/*
+ * Minimum breathing level registers
+ * For patterns 0 - 0x47, 1 - 0x48, 2 - 0x49 (step 1)
+ */
+#define AW200XX_REG_PAT0_MIN_BREATH AW200XX_REG(AW200XX_PAGE0, 0x47)
+
+/*
+ * Template 1 (rise-time) & template 2 (on-time) configuration register
+ * For patterns 0 - 0x4A, 1 - 0x4E, 2 - 0x52 (step 4)
+ */
+#define AW200XX_REG_PAT0_T0 AW200XX_REG(AW200XX_PAGE0, 0x4A)
+
+/*
+ * Template 3 (fall-time) & template 4 (off-time) configuration register
+ * For patterns 0 - 0x4B, 1 - 0x4F, 2 - 0x53 (step 4)
+ */
+#define AW200XX_REG_PAT0_T1 AW200XX_REG(AW200XX_PAGE0, 0x4B)
+
+/*
+ * Loop configuration registers:
+ * loop end point setting (LE)
+ * loop beginning point setting (LB)
+ * MSB of loop times (LT)
+ * For patterns 0 - 0x4C, 1 - 0x50, 2 - 0x54 (step 4)
+ */
+#define AW200XX_REG_PAT0_T2 AW200XX_REG(AW200XX_PAGE0, 0x4C)
+#define AW200XX_REG_PATX_T2(x) (AW200XX_REG_PAT0_T2 + (x))
+
+/*
+ * Loop configuration registers:
+ * LSB of loop times (LT)
+ * For patterns 0 - 0x4D, 1 - 0x51, 2 - 0x55 (step 4)
+ */
+#define AW200XX_REG_PAT0_T3 AW200XX_REG(AW200XX_PAGE0, 0x4D)
+#define AW200XX_REG_PATX_T3(x) (AW200XX_REG_PAT0_T3 + (x))
+
+#define AW200XX_PAT_T2_LE_MASK GENMASK(7, 6)
+#define AW200XX_PAT_T2_LB_MASK GENMASK(5, 4)
+#define AW200XX_PAT_T2_LT_MASK GENMASK(3, 0)
+#define AW200XX_PAT_T3_LT_MASK 0xFF
+#define AW200XX_PAT0_T2_LT_MSB(x) ((x) >> 8)
+#define AW200XX_PAT0_T3_LT_LSB(x) ((x) & 0xFF)
+#define AW200XX_PAT0_T_LT(msb, lsb) ((msb) << 8 | (lsb))
+#define AW200XX_PAT0_T_LT_MAX 0xFFF
+
+#define AW200XX_PAT_T_STEP 4
+
+#define AW200XX_PAT_T1_T3_MASK 0xF0
+#define AW200XX_PAT_T2_T4_MASK 0x0F
+#define AW200XX_TEMPLATE_TIME_MAX 0x0F
+
+/*
+ * Pattern mode configuration register
+ * For patterns 0 - 0x56, 1 - 0x57, 2 - 0x58 (step 1)
+ */
+#define AW200XX_REG_PAT0_CFG AW200XX_REG(AW200XX_PAGE0, 0x56)
+#define AW200XX_PAT_CFG_MODE_MASK BIT(0)
+#define AW200XX_PAT_CFG_RAMP_MASK BIT(1)
+#define AW200XX_PAT_CFG_SWITCH_MASK BIT(2)
+
+/* Start pattern register */
+#define AW200XX_REG_PATGO AW200XX_REG(AW200XX_PAGE0, 0x59)
+#define AW200XX_PATGO(x) BIT(x)
+#define AW200XX_PATGO_RUN(x, run) ((run) << (x))
+#define AW200XX_PATGO_STATE(x) BIT((x) + 4)
+
+/* Display size configuration */
+#define AW200XX_REG_DSIZE AW200XX_REG(AW200XX_PAGE0, 0x80)
+#define AW200XX_DSIZE_COLUMNS_MAX 12
+
+#define AW200XX_LED2REG(x, columns) \
+ ((x) + (((x) / (columns)) * (AW200XX_DSIZE_COLUMNS_MAX - (columns))))
+
+/* Patern selection register*/
+#define AW200XX_REG_PAT_SELECT(x, columns) \
+ AW200XX_REG(AW200XX_PAGE3, AW200XX_LED2REG(x, columns))
+#define AW200XX_PATX_SELECT(x) ((x) + 1)
+
+/*
+ * DIM current configuration register (page 4).
+ * The even address for current DIM configuration.
+ * The odd address for current FADE configuration
+ */
+#define AW200XX_REG_DIM(x, columns) \
+ AW200XX_REG(AW200XX_PAGE4, AW200XX_LED2REG(x, columns) * 2)
+#define AW200XX_REG_DIM2FADE(x) ((x) + 1)
+#define AW200XX_REG_FADE(x, columns) (AW200XX_REG_DIM(x, columns) + 1)
+
+struct aw200xx_led {
+ struct aw200xx *chip;
+ struct led_classdev cdev;
+ int dim;
+ u32 num;
+};
+
+struct aw200xx {
+ const struct aw200xx_chipdef *cdef;
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct mutex mutex;
+ DECLARE_BITMAP(pattern_leds[AW200XX_PATTERN_MAX], AW200XX_LEDS_MAX);
+ u32 num_leds;
+ u32 imax;
+ u32 display_size;
+ struct aw200xx_led leds[];
+};
+
+struct aw200xx_chipdef {
+ u32 channels;
+ u32 display_size_max;
+ u32 display_size_columns;
+};
+
+struct aw200xx_attribute {
+ struct device_attribute dev_attr;
+ u32 reg;
+ u32 mask;
+ u32 max;
+};
+
+#define to_aw200xx_attr(attr) \
+ container_of(attr, struct aw200xx_attribute, dev_attr)
+
+#define AW200XX_ATTR(_n, _m, _sh, _st, _r, _msk, _max) { \
+ .dev_attr = __ATTR(_n, _m, _sh, _st), \
+ .reg = _r, \
+ .mask = _msk, \
+ .max = _max, \
+}
+
+#define AW200XX_DEVICE_ATTR_RW(_v, _n, _sh, _st, _r, _msk, _max) \
+struct aw200xx_attribute _v##_attr = \
+ AW200XX_ATTR(_n, 0644, _sh, _st, \
+ _r, _msk, _max)
+
+#define AW200XX_DEVICE_ATTR_RO(_v, _n, _sh, _r, _msk, _max) \
+struct aw200xx_attribute _v##_attr = \
+ AW200XX_ATTR(_n, 0444, _sh, NULL, \
+ _r, _msk, _max)
+
+static ssize_t aw200xx_store_internal(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 val;
+ int ret;
+
+ ret = kstrtouint(buf, 0, &val);
+ if (ret < 0 || val > attr->max)
+ return -EINVAL;
+
+ val <<= __ffs(attr->mask);
+
+ mutex_lock(&chip->mutex);
+ ret = regmap_update_bits(chip->regmap, attr->reg, attr->mask, val);
+ mutex_unlock(&chip->mutex);
+
+ if (ret)
+ return ret;
+
+ return count;
+}
+
+static ssize_t aw200xx_show_internal(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 val;
+ int ret;
+
+ mutex_lock(&chip->mutex);
+ ret = regmap_read(chip->regmap, attr->reg, &val);
+ mutex_unlock(&chip->mutex);
+
+ if (ret)
+ return ret;
+
+ val = (val & attr->mask) >> __ffs(attr->mask);
+
+ return sysfs_emit(buf, "%u\n", val);
+}
+
+static ssize_t aw200xx_template_time_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ static const u32 ttimes_ms[] = {
+ 0, 130, 260, 380, 510, 770, 1040, 1600,
+ 2100, 2600, 3100, 4200, 5200, 6200, 7300, 8300,
+ };
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 ttime;
+ int ret;
+
+ mutex_lock(&chip->mutex);
+ ret = regmap_read(chip->regmap, attr->reg, &ttime);
+ mutex_unlock(&chip->mutex);
+
+ if (ret)
+ return ret;
+
+ ttime = (ttime & attr->mask) >> __ffs(attr->mask);
+ if (ttime >= ARRAY_SIZE(ttimes_ms))
+ return -EIO;
+
+ ttime = ttimes_ms[ttime];
+
+ /* For On & Off time minimum is 40ms */
+ if (ttime == 0 && attr->mask == AW200XX_PAT_T2_T4_MASK)
+ ttime = 40;
+
+ return sysfs_emit(buf, "%ums\n", ttime);
+}
+
+static ssize_t aw200xx_pattern_leds_store(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count,
+ bool clear)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ unsigned long *pattern_leds = chip->pattern_leds[attr->reg];
+ u32 columns = chip->cdef->display_size_columns;
+ DECLARE_BITMAP(leds, AW200XX_LEDS_MAX);
+ u32 val = clear ? 0 : AW200XX_PATX_SELECT(attr->reg);
+ u32 i;
+ int ret;
+
+ ret = bitmap_parse(buf, count, leds, chip->num_leds);
+ if (ret)
+ return -EINVAL;
+
+ mutex_lock(&chip->mutex);
+
+ for_each_set_bit(i, leds, chip->num_leds) {
+ u32 num = chip->leds[i].num;
+
+ ret = regmap_write(chip->regmap,
+ AW200XX_REG_PAT_SELECT(num, columns), val);
+ if (ret)
+ goto exit;
+
+ if (clear)
+ __clear_bit(i, pattern_leds);
+ else
+ __set_bit(i, pattern_leds);
+ }
+
+ ret = (int)count;
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+
+static ssize_t aw200xx_pattern_select_leds_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ int ret;
+
+ mutex_lock(&chip->mutex);
+ ret = sysfs_emit(buf, "%*pb\n",
+ chip->num_leds, chip->pattern_leds[attr->reg]);
+ mutex_unlock(&chip->mutex);
+
+ return ret;
+}
+
+static ssize_t aw200xx_pattern_select_leds_store(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ return aw200xx_pattern_leds_store(dev, devattr, buf, count, false);
+}
+
+static ssize_t aw200xx_pattern_clear_leds_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ DECLARE_BITMAP(leds, AW200XX_LEDS_MAX);
+ int ret;
+
+ mutex_lock(&chip->mutex);
+ bitmap_fill(leds, chip->num_leds);
+ bitmap_xor(leds, leds, chip->pattern_leds[attr->reg], chip->num_leds);
+ ret = sysfs_emit(buf, "%*pb\n", chip->num_leds, leds);
+ mutex_unlock(&chip->mutex);
+
+ return ret;
+}
+
+static ssize_t aw200xx_pattern_clear_leds_store(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ return aw200xx_pattern_leds_store(dev, devattr, buf, count, true);
+}
+
+static ssize_t aw200xx_pattern_start_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 start = 0;
+ u32 val;
+ int ret;
+
+ mutex_lock(&chip->mutex);
+
+ ret = regmap_read(chip->regmap, AW200XX_REG_PATCR, &val);
+ if (ret)
+ goto exit;
+
+ if (val & AW200XX_PATCR_PAT_ENABLE(attr->reg)) {
+ ret = regmap_read(chip->regmap, AW200XX_REG_PATGO, &val);
+ if (ret)
+ goto exit;
+
+ start = !!(val & AW200XX_PATGO(attr->reg));
+ }
+
+ ret = sysfs_emit(buf, "%u\n", start);
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+
+static ssize_t aw200xx_pattern_start_store(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 start;
+ int ret;
+
+ ret = kstrtouint(buf, 0, &start);
+ if (ret < 0 || start > attr->max)
+ return -EINVAL;
+
+ start = AW200XX_PATGO_RUN(attr->reg, start);
+
+ mutex_lock(&chip->mutex);
+
+ ret = regmap_update_bits(chip->regmap, AW200XX_REG_PATCR,
+ AW200XX_PATCR_PAT_ENABLE(attr->reg), start);
+ if (ret)
+ goto exit;
+
+ ret = regmap_update_bits(chip->regmap, AW200XX_REG_PATGO,
+ AW200XX_PATGO(attr->reg), start);
+ if (!ret)
+ ret = (int)count;
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+
+static ssize_t aw200xx_pattern_running_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 running;
+ int ret;
+
+ mutex_lock(&chip->mutex);
+
+ ret = regmap_read(chip->regmap, AW200XX_REG_PATGO, &running);
+ if (ret)
+ goto exit;
+
+ running &= AW200XX_PATGO_STATE(attr->reg);
+ ret = sysfs_emit(buf, "%u\n", !!running);
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+
+static ssize_t aw200xx_pattern_repeat_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 repeat_msb;
+ u32 repeat_lsb;
+ int ret;
+
+ mutex_lock(&chip->mutex);
+
+ ret = regmap_read(chip->regmap,
+ AW200XX_REG_PATX_T2(attr->reg), &repeat_msb);
+ if (ret)
+ goto exit;
+
+ ret = regmap_read(chip->regmap,
+ AW200XX_REG_PATX_T3(attr->reg), &repeat_lsb);
+ if (ret)
+ goto exit;
+
+ repeat_msb &= AW200XX_PAT_T2_LT_MASK;
+ repeat_lsb &= AW200XX_PAT_T3_LT_MASK;
+
+ ret = sysfs_emit(buf, "%u\n",
+ AW200XX_PAT0_T_LT(repeat_msb, repeat_lsb));
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+
+static ssize_t aw200xx_pattern_repeat_store(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct aw200xx_attribute *attr = to_aw200xx_attr(devattr);
+ struct aw200xx *chip = i2c_get_clientdata(to_i2c_client(dev));
+ u32 repeat;
+ ssize_t ret;
+
+ ret = kstrtouint(buf, 0, &repeat);
+ if (ret < 0 || repeat > attr->max)
+ return -EINVAL;
+
+ mutex_lock(&chip->mutex);
+
+ ret = regmap_update_bits(chip->regmap,
+ AW200XX_REG_PATX_T2(attr->reg),
+ AW200XX_PAT_T2_LT_MASK,
+ AW200XX_PAT0_T2_LT_MSB(repeat));
+ if (ret)
+ goto exit;
+
+ ret = regmap_update_bits(chip->regmap,
+ AW200XX_REG_PATX_T3(attr->reg),
+ AW200XX_PAT_T3_LT_MASK,
+ AW200XX_PAT0_T3_LT_LSB(repeat));
+ if (!ret)
+ ret = count;
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+
+#define AW200XX_DEVICE_ATTR_PAT_RW(_n, _sh, _st, _r, _step, _msk, _max) \
+static AW200XX_DEVICE_ATTR_RW(_n##0, _n, _sh, _st, \
+ _r, _msk, _max); \
+static AW200XX_DEVICE_ATTR_RW(_n##1, _n, _sh, _st, \
+ _r + (1 * (_step)), _msk, _max); \
+static AW200XX_DEVICE_ATTR_RW(_n##2, _n, _sh, _st, \
+ _r + (2 * (_step)), _msk, _max)
+
+#define AW200XX_DEVICE_ATTR_PAT_RO(_n, _sh, _r, _step, _msk, _max) \
+static AW200XX_DEVICE_ATTR_RO(_n##0, _n, _sh, \
+ _r, _msk, _max); \
+static AW200XX_DEVICE_ATTR_RO(_n##1, _n, _sh, \
+ _r + (1 * (_step)), _msk, _max); \
+static AW200XX_DEVICE_ATTR_RO(_n##2, _n, _sh, \
+ _r + (2 * (_step)), _msk, _max)
+
+#define AW200XX_DEFINE_ATTR_GROUP(_idx, _a0, _a1, _a2, _a3, _a4, _a5, \
+ _a6, _a7, _a8, _a9, _a10, _a11, _a12, _a13, _a14, _a15) \
+static struct attribute *aw200xx_pattern##_idx##_attributes[] = { \
+ &_a0##_idx##_attr.dev_attr.attr, \
+ &_a1##_idx##_attr.dev_attr.attr, \
+ &_a2##_idx##_attr.dev_attr.attr, \
+ &_a3##_idx##_attr.dev_attr.attr, \
+ &_a4##_idx##_attr.dev_attr.attr, \
+ &_a5##_idx##_attr.dev_attr.attr, \
+ &_a6##_idx##_attr.dev_attr.attr, \
+ &_a7##_idx##_attr.dev_attr.attr, \
+ &_a8##_idx##_attr.dev_attr.attr, \
+ &_a9##_idx##_attr.dev_attr.attr, \
+ &_a10##_idx##_attr.dev_attr.attr, \
+ &_a11##_idx##_attr.dev_attr.attr, \
+ &_a12##_idx##_attr.dev_attr.attr, \
+ &_a13##_idx##_attr.dev_attr.attr, \
+ &_a14##_idx##_attr.dev_attr.attr, \
+ &_a15##_idx##_attr.dev_attr.attr, \
+ NULL}; \
+static const struct attribute_group aw200xx_pattern##_idx##_group = { \
+ .attrs = aw200xx_pattern##_idx##_attributes, \
+ .name = "pattern"#_idx, \
+}
+
+#define AW200XX_DEFINE_ATTR_GROUPS(...) \
+AW200XX_DEFINE_ATTR_GROUP(0, __VA_ARGS__); \
+AW200XX_DEFINE_ATTR_GROUP(1, __VA_ARGS__); \
+AW200XX_DEFINE_ATTR_GROUP(2, __VA_ARGS__); \
+static const struct attribute_group *aw200xx_pattern_groups[] = { \
+ &aw200xx_pattern0_group, \
+ &aw200xx_pattern1_group, \
+ &aw200xx_pattern2_group, \
+ NULL}
+
+AW200XX_DEVICE_ATTR_PAT_RW(rise_time,
+ aw200xx_template_time_show, aw200xx_store_internal,
+ AW200XX_REG_PAT0_T0, AW200XX_PAT_T_STEP,
+ AW200XX_PAT_T1_T3_MASK, AW200XX_TEMPLATE_TIME_MAX);
+
+AW200XX_DEVICE_ATTR_PAT_RW(on_time,
+ aw200xx_template_time_show, aw200xx_store_internal,
+ AW200XX_REG_PAT0_T0, AW200XX_PAT_T_STEP,
+ AW200XX_PAT_T2_T4_MASK, AW200XX_TEMPLATE_TIME_MAX);
+
+AW200XX_DEVICE_ATTR_PAT_RW(fall_time,
+ aw200xx_template_time_show, aw200xx_store_internal,
+ AW200XX_REG_PAT0_T1, AW200XX_PAT_T_STEP,
+ AW200XX_PAT_T1_T3_MASK, AW200XX_TEMPLATE_TIME_MAX);
+
+AW200XX_DEVICE_ATTR_PAT_RW(off_time,
+ aw200xx_template_time_show, aw200xx_store_internal,
+ AW200XX_REG_PAT0_T1, AW200XX_PAT_T_STEP,
+ AW200XX_PAT_T2_T4_MASK, AW200XX_TEMPLATE_TIME_MAX);
+
+AW200XX_DEVICE_ATTR_PAT_RW(mode,
+ aw200xx_show_internal, aw200xx_store_internal,
+ AW200XX_REG_PAT0_CFG, 1,
+ AW200XX_PAT_CFG_MODE_MASK, 1);
+
+AW200XX_DEVICE_ATTR_PAT_RW(ramp,
+ aw200xx_show_internal, aw200xx_store_internal,
+ AW200XX_REG_PAT0_CFG, 1,
+ AW200XX_PAT_CFG_RAMP_MASK, 1);
+
+AW200XX_DEVICE_ATTR_PAT_RW(toggle,
+ aw200xx_show_internal, aw200xx_store_internal,
+ AW200XX_REG_PAT0_CFG, 1,
+ AW200XX_PAT_CFG_SWITCH_MASK, 1);
+
+AW200XX_DEVICE_ATTR_PAT_RW(loop_end_on,
+ aw200xx_show_internal, aw200xx_store_internal,
+ AW200XX_REG_PAT0_T2, AW200XX_PAT_T_STEP,
+ AW200XX_PAT_T2_LE_MASK, 1);
+
+AW200XX_DEVICE_ATTR_PAT_RW(loop_begin,
+ aw200xx_show_internal, aw200xx_store_internal,
+ AW200XX_REG_PAT0_T2, AW200XX_PAT_T_STEP,
+ AW200XX_PAT_T2_LB_MASK, 3);
+
+AW200XX_DEVICE_ATTR_PAT_RW(max_breathing_level,
+ aw200xx_show_internal, aw200xx_store_internal,
+ AW200XX_REG_PAT0_MAX_BREATH, 1,
+ 0xFF, AW200XX_FADE_MAX);
+
+AW200XX_DEVICE_ATTR_PAT_RW(min_breathing_level,
+ aw200xx_show_internal, aw200xx_store_internal,
+ AW200XX_REG_PAT0_MIN_BREATH, 1,
+ 0xFF, AW200XX_FADE_MAX);
+
+AW200XX_DEVICE_ATTR_PAT_RW(start,
+ aw200xx_pattern_start_show,
+ aw200xx_pattern_start_store,
+ 0, 1, 1, 1);
+
+AW200XX_DEVICE_ATTR_PAT_RO(running,
+ aw200xx_pattern_running_show, 0, 1, 0, 0);
+
+AW200XX_DEVICE_ATTR_PAT_RW(repeat,
+ aw200xx_pattern_repeat_show,
+ aw200xx_pattern_repeat_store,
+ 0, AW200XX_PAT_T_STEP,
+ 0, AW200XX_PAT0_T_LT_MAX);
+
+AW200XX_DEVICE_ATTR_PAT_RW(select_leds,
+ aw200xx_pattern_select_leds_show,
+ aw200xx_pattern_select_leds_store,
+ 0, 1, 0, 0);
+
+AW200XX_DEVICE_ATTR_PAT_RW(clear_leds,
+ aw200xx_pattern_clear_leds_show,
+ aw200xx_pattern_clear_leds_store,
+ 0, 1, 0, 0);
+
+AW200XX_DEFINE_ATTR_GROUPS(start, running, mode, ramp, toggle, repeat,
+ loop_end_on, loop_begin, select_leds, clear_leds,
+ max_breathing_level, min_breathing_level,
+ rise_time, on_time, fall_time, off_time);
+
+static ssize_t aw200xx_dim_show(struct device *dev,
+ struct device_attribute *devattr,
+ char *buf)
+{
+ struct led_classdev *cdev = dev_get_drvdata(dev);
+ struct aw200xx_led *led = container_of(cdev, struct aw200xx_led, cdev);
+ int dim = led->dim;
+ ssize_t ret;
+
+ if (dim < 0)
+ ret = sysfs_emit(buf, "auto\n");
+ else
+ ret = sysfs_emit(buf, "%d\n", dim);
+
+ return ret;
+}
+
+static ssize_t aw200xx_dim_store(struct device *dev,
+ struct device_attribute *devattr,
+ const char *buf, size_t count)
+{
+ struct led_classdev *cdev = dev_get_drvdata(dev);
+ struct aw200xx_led *led = container_of(cdev, struct aw200xx_led, cdev);
+ struct aw200xx *chip = led->chip;
+ u32 columns = chip->cdef->display_size_columns;
+ int dim;
+ ssize_t ret;
+
+ if (sysfs_streq(buf, "auto")) {
+ dim = -1;
+ } else {
+ ret = kstrtoint(buf, 0, &dim);
+ if (ret < 0 || dim > AW200XX_DIM_MAX)
+ return -EINVAL;
+ }
+
+ mutex_lock(&chip->mutex);
+
+ if (dim >= 0) {
+ ret = regmap_write(chip->regmap,
+ AW200XX_REG_DIM(led->num, columns), dim);
+ if (ret)
+ goto exit;
+ }
+
+ led->dim = dim;
+ ret = count;
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+static DEVICE_ATTR(dim, 0644, aw200xx_dim_show, aw200xx_dim_store);
+
+static struct attribute *dim_attrs[] = {
+ &dev_attr_dim.attr,
+ NULL
+};
+ATTRIBUTE_GROUPS(dim);
+
+static int aw200xx_brightness_set(struct led_classdev *cdev,
+ enum led_brightness brightness)
+{
+ struct aw200xx_led *led = container_of(cdev, struct aw200xx_led, cdev);
+ struct aw200xx *chip = led->chip;
+ int dim;
+ u32 reg;
+ int ret;
+
+ mutex_lock(&chip->mutex);
+
+ reg = AW200XX_REG_DIM(led->num, chip->cdef->display_size_columns);
+ dim = led->dim;
+
+ if (dim < 0) {
+ dim = brightness / (AW200XX_FADE_MAX / AW200XX_DIM_MAX);
+ dim = max(dim, 1);
+ }
+
+ ret = regmap_write(chip->regmap, reg, dim);
+ if (ret)
+ goto error;
+
+ ret = regmap_write(chip->regmap,
+ AW200XX_REG_DIM2FADE(reg), brightness);
+
+error:
+ mutex_unlock(&chip->mutex);
+
+ return ret;
+}
+
+static irqreturn_t aw200xx_irq_thread(int irq, void *dev_id)
+{
+ struct aw200xx *chip = dev_id;
+ unsigned long pattern_state;
+ u32 interrupt_state;
+ int i;
+ int ret;
+
+ mutex_lock(&chip->mutex);
+ ret = regmap_read(chip->regmap, AW200XX_REG_ISRFLT, &interrupt_state);
+ mutex_unlock(&chip->mutex);
+
+ if (ret) {
+ dev_err(&chip->client->dev,
+ "Failed to get interrupt status: %d\n", ret);
+ return IRQ_HANDLED;
+ }
+
+ pattern_state = FIELD_GET(AW200XX_ISRFLT_PATIS_MASK, interrupt_state);
+
+ for_each_set_bit(i, &pattern_state, AW200XX_PATTERN_MAX) {
+ char dir[sizeof("patternxx")];
+
+ snprintf(dir, sizeof(dir), "pattern%d", i);
+ sysfs_notify(&chip->client->dev.kobj, dir, "running");
+ }
+
+ return IRQ_HANDLED;
+}
+
+static int aw200xx_setup_interrupts(struct aw200xx *chip)
+{
+ struct i2c_client *i2c = chip->client;
+ int ret;
+
+ if (i2c->irq <= 0)
+ return 0;
+
+ ret = devm_request_threaded_irq(&i2c->dev, i2c->irq,
+ NULL,
+ aw200xx_irq_thread,
+ IRQF_ONESHOT,
+ i2c->name,
+ chip);
+ if (ret)
+ return dev_err_probe(&i2c->dev, ret, "Failed to request irq\n");
+
+ ret = regmap_update_bits(chip->regmap, AW200XX_REG_PATCR,
+ AW200XX_PATCR_PAT_IE_MASK,
+ AW200XX_PATCR_PAT_IE_ALL);
+ if (ret)
+ dev_err_probe(&i2c->dev, ret, "Failed to enable interrupts\n");
+
+ return ret;
+}
+
+static int aw200xx_chip_reset(const struct aw200xx *const chip)
+{
+ int ret;
+
+ ret = regmap_write(chip->regmap, AW200XX_REG_RSTR, AW200XX_RSTR_RESET);
+ if (ret)
+ return ret;
+
+ regcache_mark_dirty(chip->regmap);
+ ret = regmap_write(chip->regmap, AW200XX_REG_FCD, AW200XX_FCD_CLEAR);
+
+ return ret;
+}
+
+static int aw200xx_chip_init(const struct aw200xx *const chip)
+{
+ int ret;
+
+ ret = regmap_write(chip->regmap, AW200XX_REG_DSIZE, chip->display_size);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(chip->regmap, AW200XX_REG_SLPCR,
+ AW200XX_SLPCR_ACTIVE);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(chip->regmap, AW200XX_REG_GCCR,
+ AW200XX_GCCR_IMAX(chip->imax) | AW200XX_GCCR_ALLON);
+
+ return ret;
+}
+
+static int aw200xx_chip_check(const struct aw200xx *const chip)
+{
+ struct device *dev = &chip->client->dev;
+ u32 chipid;
+ int ret;
+
+ ret = regmap_read(chip->regmap, AW200XX_REG_IDR, &chipid);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to read chip ID\n");
+
+ if (chipid != AW200XX_IDR_CHIPID)
+ return dev_err_probe(dev, -ENODEV,
+ "Chip reported wrong ID: %x\n", chipid);
+
+ return 0;
+}
+
+static int aw200xx_probe_dt(struct device *dev, struct aw200xx *chip)
+{
+ struct fwnode_handle *child;
+ u32 imax;
+ int ret;
+ int i = 0;
+
+ ret = device_property_read_u32(dev, "display-size", &chip->display_size);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Failed to read 'display-size' property\n");
+
+ if (chip->display_size > chip->cdef->display_size_max)
+ return dev_err_probe(dev, ret,
+ "Invalid leds display size %u\n",
+ chip->display_size);
+
+ ret = device_property_read_u32(dev, "imax", &imax);
+ if (!ret && imax <= AW200XX_IMAX_MAX) {
+ chip->imax = imax;
+ } else {
+ chip->imax = AW200XX_IMAX_DEFAULT;
+ dev_info(dev, "DT property imax is missing\n");
+ }
+
+ device_for_each_child_node(dev, child) {
+ struct led_init_data init_data = {};
+ struct aw200xx_led *led;
+ u32 source;
+
+ ret = fwnode_property_read_u32(child, "reg", &source);
+ if (ret) {
+ dev_err(dev, "Missing reg property\n");
+ chip->num_leds--;
+ continue;
+ }
+
+ if (source >= chip->cdef->channels) {
+ dev_err(dev, "LED reg %u out of range (max %u)\n",
+ source, chip->cdef->channels);
+ chip->num_leds--;
+ continue;
+ }
+
+ led = &chip->leds[i];
+ led->dim = -1;
+ led->num = source;
+ led->chip = chip;
+ led->cdev.brightness_set_blocking = aw200xx_brightness_set;
+ led->cdev.groups = dim_groups;
+ init_data.fwnode = child;
+
+ ret = devm_led_classdev_register_ext(dev, &led->cdev,
+ &init_data);
+ if (ret) {
+ fwnode_handle_put(child);
+ break;
+ }
+
+ i++;
+ }
+
+ if (!chip->num_leds)
+ ret = -EINVAL;
+
+ return ret;
+}
+
+static const struct regmap_range_cfg aw200xx_ranges[] = {
+ {
+ .name = "aw200xx",
+ .range_min = 0,
+ .range_max = AW200XX_REG_MAX,
+ .selector_reg = AW200XX_REG_PAGE,
+ .selector_mask = AW200XX_PAGE_MASK,
+ .selector_shift = AW200XX_PAGE_SHIFT,
+ .window_start = 0,
+ .window_len = AW200XX_PAGE_SIZE,
+ },
+};
+
+static const struct regmap_range aw200xx_writeonly_ranges[] = {
+ regmap_reg_range(AW200XX_REG(AW200XX_PAGE1, 0x00), AW200XX_REG_MAX),
+};
+
+static const struct regmap_access_table aw200xx_readable_table = {
+ .no_ranges = aw200xx_writeonly_ranges,
+ .n_no_ranges = ARRAY_SIZE(aw200xx_writeonly_ranges),
+};
+
+static const struct regmap_range aw200xx_readonly_ranges[] = {
+ regmap_reg_range(AW200XX_REG_IDR, AW200XX_REG_IDR),
+ regmap_reg_range(AW200XX_REG_ISRFLT, AW200XX_REG_ISRFLT),
+};
+
+static const struct regmap_access_table aw200xx_writeable_table = {
+ .no_ranges = aw200xx_readonly_ranges,
+ .n_no_ranges = ARRAY_SIZE(aw200xx_readonly_ranges),
+};
+
+static const struct regmap_range aw200xx_volatile_registers[] = {
+ regmap_reg_range(AW200XX_REG_ISRFLT, AW200XX_REG_ISRFLT),
+};
+
+static const struct regmap_access_table aw200xx_volatile_table = {
+ .yes_ranges = aw200xx_volatile_registers,
+ .n_yes_ranges = ARRAY_SIZE(aw200xx_volatile_registers),
+};
+
+static const struct regmap_config aw200xx_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = AW200XX_REG_MAX,
+ .ranges = aw200xx_ranges,
+ .num_ranges = ARRAY_SIZE(aw200xx_ranges),
+ .rd_table = &aw200xx_readable_table,
+ .wr_table = &aw200xx_writeable_table,
+ .volatile_table = &aw200xx_volatile_table,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+static int aw200xx_probe(struct i2c_client *client)
+{
+ const struct aw200xx_chipdef *cdef;
+ struct aw200xx *chip;
+ int count;
+ int ret;
+
+ cdef = device_get_match_data(&client->dev);
+
+ count = device_get_child_node_count(&client->dev);
+ if (!count || count > cdef->channels)
+ return dev_err_probe(&client->dev, -EINVAL,
+ "Incorrect number of leds (%d)", count);
+
+ chip = devm_kzalloc(&client->dev,
+ struct_size(chip, leds, count),
+ GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ chip->cdef = cdef;
+ chip->num_leds = count;
+ chip->client = client;
+ i2c_set_clientdata(client, chip);
+
+ chip->regmap = devm_regmap_init_i2c(client, &aw200xx_regmap_config);
+ if (IS_ERR(chip->regmap))
+ return PTR_ERR(chip->regmap);
+
+ ret = aw200xx_chip_check(chip);
+ if (ret)
+ return ret;
+
+ mutex_init(&chip->mutex);
+
+ /* Need a lock now since after call aw200xx_probe_dt, created sysfs nodes */
+ mutex_lock(&chip->mutex);
+
+ ret = aw200xx_probe_dt(&client->dev, chip);
+ if (ret < 0)
+ goto exit;
+
+ ret = aw200xx_chip_reset(chip);
+ if (ret)
+ goto exit;
+
+ ret = aw200xx_chip_init(chip);
+ if (ret)
+ goto exit;
+
+ ret = aw200xx_setup_interrupts(chip);
+
+exit:
+ mutex_unlock(&chip->mutex);
+ return ret;
+}
+
+static void aw200xx_remove(struct i2c_client *client)
+{
+ struct aw200xx *chip = i2c_get_clientdata(client);
+
+ aw200xx_chip_reset(chip);
+ mutex_destroy(&chip->mutex);
+}
+
+static const struct aw200xx_chipdef aw20036_cdef = {
+ .channels = 36,
+ .display_size_max = 2,
+ .display_size_columns = 12,
+};
+
+static const struct aw200xx_chipdef aw20054_cdef = {
+ .channels = 54,
+ .display_size_max = 5,
+ .display_size_columns = 9,
+};
+
+static const struct aw200xx_chipdef aw20072_cdef = {
+ .channels = 72,
+ .display_size_max = 5,
+ .display_size_columns = 12,
+};
+
+static const struct i2c_device_id aw200xx_id[] = {
+ { "aw20036" },
+ { "aw20054" },
+ { "aw20072" },
+ {}
+};
+MODULE_DEVICE_TABLE(i2c, aw200xx_id);
+
+static const struct of_device_id aw200xx_match_table[] = {
+ { .compatible = "awinic,aw20036", .data = &aw20036_cdef, },
+ { .compatible = "awinic,aw20054", .data = &aw20054_cdef, },
+ { .compatible = "awinic,aw20072", .data = &aw20072_cdef, },
+ {},
+};
+MODULE_DEVICE_TABLE(of, aw200xx_match_table);
+
+static struct i2c_driver aw200xx_driver = {
+ .driver = {
+ .name = "aw200xx",
+ .of_match_table = of_match_ptr(aw200xx_match_table),
+ .dev_groups = aw200xx_pattern_groups,
+ },
+ .probe_new = aw200xx_probe,
+ .remove = aw200xx_remove,
+ .id_table = aw200xx_id,
+};
+
+module_i2c_driver(aw200xx_driver);
+
+MODULE_AUTHOR("Martin Kurbanov <mmkurbanov@sberdevices.ru>");
+MODULE_DESCRIPTION("AW200XX LED driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:leds-aw200xx");