[v2,03/15] tty: serial: qcom-geni-serial: align #define values
Commit Message
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Keep the #define symbols aligned for better readability.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
drivers/tty/serial/qcom_geni_serial.c | 62 +++++++++++++--------------
1 file changed, 31 insertions(+), 31 deletions(-)
@@ -39,57 +39,57 @@
#define SE_UART_MANUAL_RFR 0x2ac
/* SE_UART_TRANS_CFG */
-#define UART_TX_PAR_EN BIT(0)
-#define UART_CTS_MASK BIT(1)
+#define UART_TX_PAR_EN BIT(0)
+#define UART_CTS_MASK BIT(1)
/* SE_UART_TX_STOP_BIT_LEN */
-#define TX_STOP_BIT_LEN_1 0
-#define TX_STOP_BIT_LEN_2 2
+#define TX_STOP_BIT_LEN_1 0
+#define TX_STOP_BIT_LEN_2 2
/* SE_UART_RX_TRANS_CFG */
-#define UART_RX_PAR_EN BIT(3)
+#define UART_RX_PAR_EN BIT(3)
/* SE_UART_RX_WORD_LEN */
-#define RX_WORD_LEN_MASK GENMASK(9, 0)
+#define RX_WORD_LEN_MASK GENMASK(9, 0)
/* SE_UART_RX_STALE_CNT */
-#define RX_STALE_CNT GENMASK(23, 0)
+#define RX_STALE_CNT GENMASK(23, 0)
/* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */
-#define PAR_CALC_EN BIT(0)
-#define PAR_EVEN 0x00
-#define PAR_ODD 0x01
-#define PAR_SPACE 0x10
+#define PAR_CALC_EN BIT(0)
+#define PAR_EVEN 0x00
+#define PAR_ODD 0x01
+#define PAR_SPACE 0x10
/* SE_UART_MANUAL_RFR register fields */
-#define UART_MANUAL_RFR_EN BIT(31)
-#define UART_RFR_NOT_READY BIT(1)
-#define UART_RFR_READY BIT(0)
+#define UART_MANUAL_RFR_EN BIT(31)
+#define UART_RFR_NOT_READY BIT(1)
+#define UART_RFR_READY BIT(0)
/* UART M_CMD OP codes */
-#define UART_START_TX 0x1
+#define UART_START_TX 0x1
/* UART S_CMD OP codes */
-#define UART_START_READ 0x1
-
-#define UART_OVERSAMPLING 32
-#define STALE_TIMEOUT 16
-#define DEFAULT_BITS_PER_CHAR 10
-#define GENI_UART_CONS_PORTS 1
-#define GENI_UART_PORTS 3
-#define DEF_FIFO_DEPTH_WORDS 16
-#define DEF_TX_WM 2
-#define DEF_FIFO_WIDTH_BITS 32
-#define UART_RX_WM 2
+#define UART_START_READ 0x1
+
+#define UART_OVERSAMPLING 32
+#define STALE_TIMEOUT 16
+#define DEFAULT_BITS_PER_CHAR 10
+#define GENI_UART_CONS_PORTS 1
+#define GENI_UART_PORTS 3
+#define DEF_FIFO_DEPTH_WORDS 16
+#define DEF_TX_WM 2
+#define DEF_FIFO_WIDTH_BITS 32
+#define UART_RX_WM 2
/* SE_UART_LOOPBACK_CFG */
-#define RX_TX_SORTED BIT(0)
-#define CTS_RTS_SORTED BIT(1)
-#define RX_TX_CTS_RTS_SORTED (RX_TX_SORTED | CTS_RTS_SORTED)
+#define RX_TX_SORTED BIT(0)
+#define CTS_RTS_SORTED BIT(1)
+#define RX_TX_CTS_RTS_SORTED (RX_TX_SORTED | CTS_RTS_SORTED)
/* UART pin swap value */
-#define DEFAULT_IO_MACRO_IO0_IO1_MASK GENMASK(3, 0)
+#define DEFAULT_IO_MACRO_IO0_IO1_MASK GENMASK(3, 0)
#define IO_MACRO_IO0_SEL 0x3
-#define DEFAULT_IO_MACRO_IO2_IO3_MASK GENMASK(15, 4)
+#define DEFAULT_IO_MACRO_IO2_IO3_MASK GENMASK(15, 4)
#define IO_MACRO_IO2_IO3_SWAP 0x4640
/* We always configure 4 bytes per FIFO word */