diff mbox series

[for-next,4/5] scsi: hisi_sas: Fix SATA devices missing issue during I_T nexus reset

Message ID 20221118083714.4034612-5-zhanjie9@hisilicon.com
State New
Headers
Series scsi: hisi_sas/libsas: Fix SATA devices missing issue during hisi_sas_debug_I_T_nexus_reset() |

Commit Message

Jie Zhan Nov. 18, 2022, 8:37 a.m. UTC 
  SATA devices on an expander may be removed and not be found again
when I_T nexus reset and revalidation are processed simultaneously.

The issue comes from:

- Revalidation can remove SATA devices in link reset, e.g. in
  hisi_sas_clear_nexus_ha().

- However, hisi_sas_debug_I_T_nexus_reset() polls the state of a SATA
  device on an expander after sending link_reset, where it calls:
   hisi_sas_debug_I_T_nexus_reset
    sas_ata_wait_after_reset
     ata_wait_after_reset
      ata_wait_ready
       smp_ata_check_ready
        sas_ex_phy_discover
         sas_ex_phy_discover_helper
          sas_set_ex_phy
  The ex_phy's change count is updated in sas_set_ex_phy(), so SATA devices
  after a link reset may not be found later through revalidation.

A similar issue was reported in:
commit 0f3fce5cc77e ("[SCSI] libsas: fix ata_eh clobbering ex_phys via
smp_ata_check_ready")
commit 87c8331fcf72 ("[SCSI] libsas: prevent domain rediscovery competing
with ata error handling").

To address this issue, in hisi_sas_debug_I_T_nexus_reset(), we now call
smp_ata_check_ready_type() that only polls the device type while not
updating the ex_phy's data of libsas.

Fixes: 71453bd9d1bf ("scsi: hisi_sas: Use sas_ata_wait_after_reset() in IT nexus reset")
Signed-off-by: Jie Zhan <zhanjie9@hisilicon.com>
---
 drivers/scsi/hisi_sas/hisi_sas_main.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)
diff mbox series

Patch

diff --git a/drivers/scsi/hisi_sas/hisi_sas_main.c b/drivers/scsi/hisi_sas/hisi_sas_main.c
index 62080d0fad6f..41ba22f6c7f0 100644
--- a/drivers/scsi/hisi_sas/hisi_sas_main.c
+++ b/drivers/scsi/hisi_sas/hisi_sas_main.c
@@ -1694,13 +1694,15 @@  static int hisi_sas_debug_I_T_nexus_reset(struct domain_device *device)
 		return rc;
 	}
 
+	/* Remote phy */
 	if (rc)
 		return rc;
 
-	/* Remote phy */
 	if (dev_is_sata(device)) {
-		rc = sas_ata_wait_after_reset(device,
-					HISI_SAS_WAIT_PHYUP_TIMEOUT);
+		struct ata_link *link = &device->sata_dev.ap->link;
+
+		rc = ata_wait_after_reset(link, HISI_SAS_WAIT_PHYUP_TIMEOUT,
+					  smp_ata_check_ready_type);
 	} else {
 		msleep(2000);
 	}