arm64: dts: qcom: sm8450-nagara: Add gpio line names for TLMM

Message ID 20221117141613.19942-1-konrad.dybcio@linaro.org
State New
Headers
Series arm64: dts: qcom: sm8450-nagara: Add gpio line names for TLMM |

Commit Message

Konrad Dybcio Nov. 17, 2022, 2:16 p.m. UTC
  Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the PDX223&224 DTSIs to better document the hardware.

Diff between 223 and 224:
< 	gpio-line-names = "NC", /* GPIO_0 */
< 			  "NC",
< 			  "NC",
< 			  "NC",
> 	gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
> 			  "TELE_SPI_MOSI",
> 			  "TELE_SPI_CLK",
> 			  "TELE_SPI_CS_N",
< 			  "PM8010_2_RESET_N",
> 			  "NC",
< 			  "NC",
> 			  "UWIDEC_PWR_EN",
< 			  "TOF_RST_N",
> 			  "NC"
< 			  "QLINK1_REQ",
< 			  "QLINK1_EN", /* GPIO_160 */
< 			  "QLINK1_WMSS_RESET_N",
> 			  "NC",
> 			  "NC", /* GPIO_160 */
> 			  "NC",
The tele lens setup is different on 1 IV and 5 IV and power wiring
is different for some lenses, so it makes sense. As for QLINK, no
idea.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 .../qcom/sm8450-sony-xperia-nagara-pdx223.dts | 213 ++++++++++++++++++
 .../qcom/sm8450-sony-xperia-nagara-pdx224.dts | 213 ++++++++++++++++++
 2 files changed, 426 insertions(+)
  

Comments

Bjorn Andersson Dec. 6, 2022, 6:19 p.m. UTC | #1
On Thu, 17 Nov 2022 15:16:13 +0100, Konrad Dybcio wrote:
> Sony ever so graciously provides GPIO line names in their downstream
> kernel (though sometimes they are not 100% accurate and you can judge
> that by simply looking at them and with what drivers they are used).
> 
> Add these to the PDX223&224 DTSIs to better document the hardware.
> 
> Diff between 223 and 224:
> < 	gpio-line-names = "NC", /* GPIO_0 */
> < 			  "NC",
> < 			  "NC",
> < 			  "NC",
> > 	gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
> > 			  "TELE_SPI_MOSI",
> > 			  "TELE_SPI_CLK",
> > 			  "TELE_SPI_CS_N",
> < 			  "PM8010_2_RESET_N",
> > 			  "NC",
> < 			  "NC",
> > 			  "UWIDEC_PWR_EN",
> < 			  "TOF_RST_N",
> > 			  "NC"
> < 			  "QLINK1_REQ",
> < 			  "QLINK1_EN", /* GPIO_160 */
> < 			  "QLINK1_WMSS_RESET_N",
> > 			  "NC",
> > 			  "NC", /* GPIO_160 */
> > 			  "NC",
> The tele lens setup is different on 1 IV and 5 IV and power wiring
> is different for some lenses, so it makes sense. As for QLINK, no
> idea.
> 
> [...]

Applied, thanks!

[1/1] arm64: dts: qcom: sm8450-nagara: Add gpio line names for TLMM
      commit: 15245c93d3c8775a8405c0de18704a8c17a41775

Best regards,
  

Patch

diff --git a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
index 3ab145877094..b83500316a81 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
@@ -12,3 +12,216 @@  / {
 	model = "Sony Xperia 1 IV";
 	compatible = "sony,pdx223", "qcom,sm8450";
 };
+
+&tlmm {
+	gpio-line-names = "NC", /* GPIO_0 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "WLC_I2C_SDA",
+			  "WLC_I2C_SCL",
+			  "NC",
+			  "PM8010_1_RESET_N",
+			  "WLC_INT_N",
+			  "NC",
+			  "NC", /* GPIO_10 */
+			  "PM8010_2_RESET_N",
+			  "DISP_ERR_FG",
+			  "HALL_INT_N",
+			  "ALS_PROX_INT_N",
+			  "IMU1_INT",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "DISP_RESET_N",
+			  "DISP_VDDR_EN",
+			  "TS_RESET_N", /* GPIO_20 */
+			  "TS_INT_N",
+			  "NC",
+			  "TELEC_PWR_EN",
+			  "CAM1_RESET_N",
+			  "LEO_CAM0_RESET_N",
+			  "DEBUG_UART_TX",
+			  "DEBUG_UART_RX",
+			  "FP_SPI_MISO",
+			  "FP_SPI_MOSI",
+			  "FP_SPI_CLK", /* GPIO_30 */
+			  "FP_SPI_CS_N",
+			  "NFC_I2C_SDA",
+			  "NFC_I2C_SCL",
+			  "NFC_EN",
+			  "NFC_CLK_REQ",
+			  "NFC_ESE_SPI_MISO",
+			  "NFC_ESE_SPI_MOSI",
+			  "NFC_ESE_SPI_CLK",
+			  "NFC_ESE_SPI_CS",
+			  "FP_INT_N", /* GPIO_40 */
+			  "NC",
+			  "FP_RESET_N",
+			  "WCD_RST_N",
+			  "NC",
+			  "NFC_DWL_REQ",
+			  "NFC_IRQ",
+			  "FORCE_USB_BOOT",
+			  "APPS_I2C_1_SDA",
+			  "APPS_I2C_1_SCL",
+			  "SBU_SW_OE", /* GPIO_50 */
+			  "SBU_SW_SEL",
+			  "SPK_AMP_I2C_SDA",
+			  "SPK_AMP_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "GNSS_ELNA_EN0",
+			  "NC",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "RGBC_IR_INT",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_70 */
+			  "NC",
+			  "HAP_I2C_SDA",
+			  "HAP_I2C_SCL",
+			  "HAP_RST_N",
+			  "HAP_INT_N",
+			  "HST_BT_UART_CTS",
+			  "HST_BT_UART_RFR",
+			  "HST_BT_UART_TX",
+			  "HST_BT_UART_RX",
+			  "HST_WLAN_EN", /* GPIO_80 */
+			  "HST_BT_EN",
+			  "HST_SW_CTRL",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "DISP_VSYNC",
+			  "NC",
+			  "NC",
+			  "HW_ID_0",
+			  "HW_ID_1", /* GPIO_90 */
+			  "USB_CC_DIR",
+			  "TRAY_DET",
+			  "SW_SERVICE",
+			  "PCIE0_RESET_N",
+			  "PCIE0_CLK_REQ_N",
+			  "PCIE0_WAKE_N",
+			  "OIS_ENABLE_WIDE",
+			  "DEBUG_GPIO0",
+			  "NC",
+			  "CAM_MCLK0", /* GPIO_100 */
+			  "CAM_MCLK1",
+			  "CAM_MCLK2",
+			  "CAM_MCLK3",
+			  "NC",
+			  "NC",
+			  "TOF_RST_N",
+			  "CAM_SOF",
+			  "NC",
+			  "AFEXPTMG_TELE",
+			  "CCI_I2C0_SDA", /* GPIO_110 */
+			  "CCI_I2C0_SCL",
+			  "CCI_I2C1_SDA",
+			  "CCI_I2C1_SCL",
+			  "CCI_I2C2_SDA",
+			  "CCI_I2C2_SCL",
+			  "NC",
+			  "CAM2_RESET_N",
+			  "NC",
+			  "EXT_VD0_XVS",
+			  "CAM3_RESET_N", /* GPIO_120 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "RF_ID_EXTENSION_2",
+			  "HAP_I2S_CLK",
+			  "HAP_I2S_DOUT",
+			  "HAP_TRG1",
+			  "HAP_I2S_SYNC",
+			  "UIM1_DATA", /* GPIO_130 */
+			  "UIM1_CLK",
+			  "UIM1_RESET",
+			  "TRAY_DET",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RESET",
+			  "UIM2_PRESENT",
+			  "SM_RFFE0_CLK",
+			  "SM_RFFE0_DATA",
+			  "SM_RFFE1_CLK", /* GPIO_140 */
+			  "SM_RFFE1_DATA",
+			  "SM_MSS_GRFC4",
+			  "HST_AS_EN",
+			  "LAA_RX_EN",
+			  "NC",
+			  "SM_RFFE4_CLK",
+			  "SM_RFFE4_DATA",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "RF_LCD_ID_EN", /* GPIO_150 */
+			  "RF_ID_EXTENSION",
+			  "SM_MSS_GRFC12",
+			  "NFC_COLD_RST",
+			  "NC",
+			  "NC",
+			  "SDR1_QLINK0_REQ",
+			  "SDR1_QLINK0_EN",
+			  "SDR1_QLINK0_WMSS_RESET_N",
+			  "QLINK1_REQ",
+			  "QLINK1_EN", /* GPIO_160 */
+			  "QLINK1_WMSS_RESET_N",
+			  "SDR2_QLINK2_REQ",
+			  "SDR2_QLINK2_EN",
+			  "SDR2_QLINK2_WMSS_RESET_N",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1", /* GPIO_170 */
+			  "SM_DMIC1_CLK",
+			  "SM_DMIC1_DATA",
+			  "SM_DMIC2_CLK",
+			  "SM_DMIC2_DATA",
+			  "SPK_AMP_I2S_CLK",
+			  "SPK_AMP_I2S_WS",
+			  "NC",
+			  "NC",
+			  "WCD_SWR_TX_DATA2",
+			  "SPK_AMP_I2S_ASP_DIN", /* GPIO_180 */
+			  "SPK_AMP_I2S_ASP_DOUT",
+			  "SPK_AMP_INT_N",
+			  "SPK_AMP_RESET_N",
+			  "HST_BT_WLAN_SLIMBUS_CLK",
+			  "HST_BT_WLAN_SLIMBUS_DAT0",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "MAG_I2C_SDA", /* GPIO_190 */
+			  "MAG_I2C_SCL",
+			  "IMU_SPI_MISO",
+			  "IMU_SPI_MOSI",
+			  "IMU_SPI_CLK",
+			  "IMU_SPI_CS_N",
+			  "SENSOR_I2C_SDA",
+			  "SENSOR_I2C_SCL",
+			  "OIS_TELE_I2C_SDA",
+			  "OIS_TELE_I2C_SCL",
+			  "NC", /* GPIO_200 */
+			  "OIS_ENABLE_TELE",
+			  "HST_BLE_UART_TX",
+			  "HST_BLE_UART_RX",
+			  "HSTP_CLK_CFG_SEL",
+			  "NC",
+			  "APPS_I2C_0_SDA",
+			  "APPS_I2C_0_SCL",
+			  "CCI_I2C3_SDA",
+			  "CCI_I2C3_SCL";
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
index 0d64d3c0afed..13c2fc4bccfc 100644
--- a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
+++ b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx224.dts
@@ -19,3 +19,216 @@  imx563_vdig_vreg: imx563-vdig-regulator {
 		enable-active-high;
 	};
 };
+
+&tlmm {
+	gpio-line-names = "TELE_SPI_MISO", /* GPIO_0 */
+			  "TELE_SPI_MOSI", /* SONY says NC, but it only makes sense this way.. */
+			  "TELE_SPI_CLK",
+			  "TELE_SPI_CS_N",
+			  "WLC_I2C_SDA",
+			  "WLC_I2C_SCL",
+			  "NC",
+			  "PM8010_1_RESET_N",
+			  "WLC_INT_N",
+			  "NC",
+			  "NC", /* GPIO_10 */
+			  "NC",
+			  "DISP_ERR_FG",
+			  "HALL_INT_N",
+			  "ALS_PROX_INT_N",
+			  "IMU1_INT",
+			  "TS_I2C_SDA",
+			  "TS_I2C_SCL",
+			  "DISP_RESET_N",
+			  "DISP_VDDR_EN",
+			  "TS_RESET_N", /* GPIO_20 */
+			  "TS_INT_N",
+			  "UWIDEC_PWR_EN",
+			  "TELEC_PWR_EN",
+			  "CAM1_RESET_N",
+			  "LEO_CAM0_RESET_N",
+			  "DEBUG_UART_TX",
+			  "DEBUG_UART_RX",
+			  "FP_SPI_MISO",
+			  "FP_SPI_MOSI",
+			  "FP_SPI_CLK", /* GPIO_30 */
+			  "FP_SPI_CS_N",
+			  "NFC_I2C_SDA",
+			  "NFC_I2C_SCL",
+			  "NFC_EN",
+			  "NFC_CLK_REQ",
+			  "NFC_ESE_SPI_MISO",
+			  "NFC_ESE_SPI_MOSI",
+			  "NFC_ESE_SPI_CLK",
+			  "NFC_ESE_SPI_CS",
+			  "FP_INT_N", /* GPIO_40 */
+			  "NC",
+			  "FP_RESET_N",
+			  "WCD_RST_N",
+			  "NC",
+			  "NFC_DWL_REQ",
+			  "NFC_IRQ",
+			  "FORCE_USB_BOOT",
+			  "APPS_I2C_1_SDA",
+			  "APPS_I2C_1_SCL",
+			  "SBU_SW_OE", /* GPIO_50 */
+			  "SBU_SW_SEL",
+			  "SPK_AMP_I2C_SDA",
+			  "SPK_AMP_I2C_SCL",
+			  "NC",
+			  "NC",
+			  "CAMSENSOR_I2C_SDA",
+			  "CAMSENSOR_I2C_SCL",
+			  "GNSS_ELNA_EN0",
+			  "NC",
+			  "NC", /* GPIO_60 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "RGBC_IR_INT",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC", /* GPIO_70 */
+			  "NC",
+			  "HAP_I2C_SDA",
+			  "HAP_I2C_SCL",
+			  "HAP_RST_N",
+			  "HAP_INT_N",
+			  "HST_BT_UART_CTS",
+			  "HST_BT_UART_RFR",
+			  "HST_BT_UART_TX",
+			  "HST_BT_UART_RX",
+			  "HST_WLAN_EN", /* GPIO_80 */
+			  "HST_BT_EN",
+			  "HST_SW_CTRL",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "DISP_VSYNC",
+			  "NC",
+			  "NC",
+			  "HW_ID_0",
+			  "HW_ID_1", /* GPIO_90 */
+			  "USB_CC_DIR",
+			  "TRAY_DET",
+			  "SW_SERVICE",
+			  "PCIE0_RESET_N",
+			  "PCIE0_CLK_REQ_N",
+			  "PCIE0_WAKE_N",
+			  "OIS_ENABLE_WIDE",
+			  "DEBUG_GPIO0",
+			  "NC",
+			  "CAM_MCLK0", /* GPIO_100 */
+			  "CAM_MCLK1",
+			  "CAM_MCLK2",
+			  "CAM_MCLK3",
+			  "NC",
+			  "NC",
+			  "NC", /* SONY didn't rename this, but there's no ToF so it's likely NC */
+			  "CAM_SOF",
+			  "NC",
+			  "AFEXPTMG_TELE",
+			  "CCI_I2C0_SDA", /* GPIO_110 */
+			  "CCI_I2C0_SCL",
+			  "CCI_I2C1_SDA",
+			  "CCI_I2C1_SCL",
+			  "CCI_I2C2_SDA",
+			  "CCI_I2C2_SCL",
+			  "NC",
+			  "CAM2_RESET_N",
+			  "NC",
+			  "EXT_VD0_XVS",
+			  "CAM3_RESET_N", /* GPIO_120 */
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "RF_ID_EXTENSION_2",
+			  "HAP_I2S_CLK",
+			  "HAP_I2S_DOUT",
+			  "HAP_TRG1",
+			  "HAP_I2S_SYNC",
+			  "UIM1_DATA", /* GPIO_130 */
+			  "UIM1_CLK",
+			  "UIM1_RESET",
+			  "TRAY_DET",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RESET",
+			  "UIM2_PRESENT",
+			  "SM_RFFE0_CLK",
+			  "SM_RFFE0_DATA",
+			  "SM_RFFE1_CLK", /* GPIO_140 */
+			  "SM_RFFE1_DATA",
+			  "SM_MSS_GRFC4",
+			  "HST_AS_EN",
+			  "LAA_RX_EN",
+			  "NC",
+			  "SM_RFFE4_CLK",
+			  "SM_RFFE4_DATA",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "RF_LCD_ID_EN", /* GPIO_150 */
+			  "RF_ID_EXTENSION",
+			  "SM_MSS_GRFC12",
+			  "NFC_COLD_RST",
+			  "NC",
+			  "NC",
+			  "SDR1_QLINK0_REQ",
+			  "SDR1_QLINK0_EN",
+			  "SDR1_QLINK0_WMSS_RESET_N",
+			  "NC",
+			  "NC", /* GPIO_160 */
+			  "NC",
+			  "SDR2_QLINK2_REQ",
+			  "SDR2_QLINK2_EN",
+			  "SDR2_QLINK2_WMSS_RESET_N",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1", /* GPIO_170 */
+			  "SM_DMIC1_CLK",
+			  "SM_DMIC1_DATA",
+			  "SM_DMIC2_CLK",
+			  "SM_DMIC2_DATA",
+			  "SPK_AMP_I2S_CLK",
+			  "SPK_AMP_I2S_WS",
+			  "NC",
+			  "NC",
+			  "WCD_SWR_TX_DATA2",
+			  "SPK_AMP_I2S_ASP_DIN", /* GPIO_180 */
+			  "SPK_AMP_I2S_ASP_DOUT",
+			  "SPK_AMP_INT_N",
+			  "SPK_AMP_RESET_N",
+			  "HST_BT_WLAN_SLIMBUS_CLK",
+			  "HST_BT_WLAN_SLIMBUS_DAT0",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "NC",
+			  "MAG_I2C_SDA", /* GPIO_190 */
+			  "MAG_I2C_SCL",
+			  "IMU_SPI_MISO",
+			  "IMU_SPI_MOSI",
+			  "IMU_SPI_CLK",
+			  "IMU_SPI_CS_N",
+			  "SENSOR_I2C_SDA",
+			  "SENSOR_I2C_SCL",
+			  "OIS_TELE_I2C_SDA",
+			  "OIS_TELE_I2C_SCL",
+			  "NC", /* GPIO_200 */
+			  "OIS_ENABLE_TELE",
+			  "HST_BLE_UART_TX",
+			  "HST_BLE_UART_RX",
+			  "HSTP_CLK_CFG_SEL",
+			  "NC",
+			  "APPS_I2C_0_SDA",
+			  "APPS_I2C_0_SCL",
+			  "CCI_I2C3_SDA",
+			  "CCI_I2C3_SCL";
+};