@@ -12013,6 +12013,13 @@ F: drivers/*/*loongarch*
F: Documentation/loongarch/
F: Documentation/translations/zh_CN/loongarch/
+LOONGSON-2 SOC SERIES THERMAL DRIVER
+M: zhanghongchen <zhanghongchen@loongson.cn>
+M: Yinbo Zhu <zhuyinbo@loongson.cn>
+L: linux-pm@vger.kernel.org
+S: Maintained
+F: drivers/thermal/loongson2_thermal.c
+
LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
M: Sathya Prakash <sathya.prakash@broadcom.com>
M: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
@@ -504,4 +504,14 @@ config KHADAS_MCU_FAN_THERMAL
If you say yes here you get support for the FAN controlled
by the Microcontroller found on the Khadas VIM boards.
+config LOONGSON2_THERMAL
+ tristate "Loongson-2 SoC series thermal driver"
+ depends on LOONGARCH || COMPILE_TEST
+ depends on OF
+ help
+ Support for Thermal driver found on Loongson-2 SoC series platforms.
+ It supports one critical trip point and one passive trip point. The
+ cpufreq and the pwm fan is used as the cooling device to throttle
+ CPUs when the passive trip is crossed.
+
endif
@@ -61,3 +61,4 @@ obj-$(CONFIG_UNIPHIER_THERMAL) += uniphier_thermal.o
obj-$(CONFIG_AMLOGIC_THERMAL) += amlogic_thermal.o
obj-$(CONFIG_SPRD_THERMAL) += sprd_thermal.o
obj-$(CONFIG_KHADAS_MCU_FAN_THERMAL) += khadas_mcu_fan.o
+obj-$(CONFIG_LOONGSON2_THERMAL) += loongson2_thermal.o
new file mode 100644
@@ -0,0 +1,262 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Author: zhanghongchen <zhanghongchen@loongson.cn>
+ * Yinbo Zhu <zhuyinbo@loongson.cn>
+ * Copyright (C) 2022-2023 Loongson Technology Corporation Limited
+ */
+
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/of_device.h>
+#include <linux/thermal.h>
+#include "thermal_hwmon.h"
+
+#define LOONGSON2_SOC_MAX_SENSOR_NUM 4
+
+#define LOONGSON2_TSENSOR_CTRL_HI 0x0
+#define LOONGSON2_TSENSOR_CTRL_LO 0x8
+#define LOONGSON2_TSENSOR_STATUS 0x10
+#define LOONGSON2_TSENSOR_OUT 0x14
+
+struct loongson2_thermal_data {
+ struct thermal_zone_device *tzd;
+ int irq;
+ int id;
+ void __iomem *regs;
+ struct platform_device *pdev;
+ u16 ctrl_low_val;
+ u16 ctrl_hi_val;
+};
+
+static int loongson2_thermal_set(struct loongson2_thermal_data *data,
+ int low, int high, bool enable)
+{
+ u64 reg_ctrl = 0;
+ int reg_off = data->id * 2;
+
+ if (low > high)
+ return -EINVAL;
+
+ low = min(low, -100);
+ high = max(high, 155);
+
+ low += 100;
+ high += 100;
+
+ reg_ctrl |= low;
+ reg_ctrl |= enable ? 0x100 : 0;
+ writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+
+ reg_ctrl = 0;
+ reg_ctrl |= high;
+ reg_ctrl |= enable ? 0x100 : 0;
+ writew(reg_ctrl, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+ return 0;
+}
+
+static int loongson2_thermal_get_temp(struct thermal_zone_device *tz, int *temp)
+{
+ u32 reg_val;
+ struct loongson2_thermal_data *data = tz->devdata;
+
+ reg_val = readl(data->regs + LOONGSON2_TSENSOR_OUT);
+ *temp = ((reg_val & 0xff) - 100) * 1000;
+
+ return 0;
+}
+
+static int loongson2_thermal_get_sensor_id(void)
+{
+ int ret, id;
+ struct of_phandle_args sensor_specs;
+ struct device_node *np, *sensor_np;
+
+ np = of_find_node_by_name(NULL, "thermal-zones");
+ if (!np)
+ return -ENODEV;
+
+ sensor_np = of_get_next_child(np, NULL);
+ ret = of_parse_phandle_with_args(sensor_np, "thermal-sensors",
+ "#thermal-sensor-cells",
+ 0, &sensor_specs);
+ if (ret) {
+ of_node_put(np);
+ of_node_put(sensor_np);
+ return ret;
+ }
+
+ if (sensor_specs.args_count >= 1) {
+ id = sensor_specs.args[0];
+ WARN(sensor_specs.args_count > 1,
+ "%s: too many cells in sensor specifier %d\n",
+ sensor_specs.np->name, sensor_specs.args_count);
+ } else {
+ id = 0;
+ }
+
+ of_node_put(np);
+ of_node_put(sensor_np);
+
+ return id;
+}
+
+static irqreturn_t loongson2_thermal_alarm_irq(int irq, void *dev)
+{
+ struct loongson2_thermal_data *data = dev;
+
+ /* clear interrupt */
+ writeb(0x3, data->regs + LOONGSON2_TSENSOR_STATUS);
+
+ disable_irq_nosync(irq);
+
+ return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t loongson2_thermal_irq_thread(int irq, void *dev)
+{
+ struct loongson2_thermal_data *data = dev;
+
+ thermal_zone_device_update(data->tzd,
+ THERMAL_EVENT_UNSPECIFIED);
+ enable_irq(data->irq);
+
+ return IRQ_HANDLED;
+}
+
+static int loongson2_thermal_set_trips(struct thermal_zone_device *tz, int low, int high)
+{
+ struct loongson2_thermal_data *data = tz->devdata;
+
+ return loongson2_thermal_set(data, low/1000, high/1000, true);
+}
+
+static const struct thermal_zone_device_ops loongson2_of_thermal_ops = {
+ .get_temp = loongson2_thermal_get_temp,
+ .set_trips = loongson2_thermal_set_trips,
+};
+
+static int loongson2_thermal_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct loongson2_thermal_data *data;
+ int ret;
+
+ data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->pdev = pdev;
+ platform_set_drvdata(pdev, data);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ data->regs = devm_ioremap(dev, res->start, resource_size(res));
+ if (IS_ERR(data->regs))
+ return PTR_ERR(data->regs);
+
+ /* get irq */
+ data->irq = platform_get_irq(pdev, 0);
+ if (data->irq < 0)
+ return data->irq;
+
+ /* get id */
+ data->id = loongson2_thermal_get_sensor_id();
+ if (data->id > LOONGSON2_SOC_MAX_SENSOR_NUM - 1 || data->id < 0) {
+ dev_err(dev, "sensor id error,must be in <0 ~ %d>\n",
+ LOONGSON2_SOC_MAX_SENSOR_NUM - 1);
+ return -EINVAL;
+ }
+
+ writeb(0xff, data->regs + LOONGSON2_TSENSOR_STATUS);
+
+ loongson2_thermal_set(data, 0, 0, false);
+
+ data->tzd = devm_thermal_of_zone_register(&pdev->dev, data->id, data,
+ &loongson2_of_thermal_ops);
+ if (IS_ERR(data->tzd))
+ return dev_err_probe(&pdev->dev, PTR_ERR(data->tzd),
+ "failed to register");
+
+ ret = devm_request_threaded_irq(dev, data->irq,
+ loongson2_thermal_alarm_irq, loongson2_thermal_irq_thread,
+ IRQF_ONESHOT, "loongson2_thermal", data);
+ if (ret < 0) {
+ dev_err(dev, "failed to request alarm irq: %d\n", ret);
+ return ret;
+ }
+
+ /*
+ * Thermal_zone doesn't enable hwmon as default,
+ * enable it here
+ */
+ data->tzd->tzp->no_hwmon = false;
+ if (devm_thermal_add_hwmon_sysfs(data->tzd))
+ dev_warn(&pdev->dev, "Failed to add hwmon sysfs attributes\n");
+
+ return 0;
+}
+
+static int loongson2_thermal_remove(struct platform_device *pdev)
+{
+ struct loongson2_thermal_data *data = platform_get_drvdata(pdev);
+ int reg_off = data->id * 2;
+
+ /* disable interrupt */
+ writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+ writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+ return 0;
+}
+
+static const struct of_device_id of_loongson2_thermal_match[] = {
+ { .compatible = "loongson,ls2k-thermal",},
+ { /* end */ }
+};
+MODULE_DEVICE_TABLE(of, of_loongson2_thermal_match);
+
+static int __maybe_unused loongson2_thermal_suspend(struct device *dev)
+{
+ struct loongson2_thermal_data *data = dev_get_drvdata(dev);
+ int reg_off = data->id * 2;
+
+ data->ctrl_low_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+ data->ctrl_hi_val = readw(data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+ writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+ writew(0, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+ return 0;
+}
+
+static int __maybe_unused loongson2_thermal_resume(struct device *dev)
+{
+ struct loongson2_thermal_data *data = dev_get_drvdata(dev);
+ int reg_off = data->id * 2;
+
+ writew(data->ctrl_low_val, data->regs + LOONGSON2_TSENSOR_CTRL_LO + reg_off);
+ writew(data->ctrl_hi_val, data->regs + LOONGSON2_TSENSOR_CTRL_HI + reg_off);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(loongson2_thermal_pm_ops,
+ loongson2_thermal_suspend, loongson2_thermal_resume);
+
+static struct platform_driver loongson2_thermal_driver = {
+ .driver = {
+ .name = "loongson2_thermal",
+ .pm = &loongson2_thermal_pm_ops,
+ .of_match_table = of_loongson2_thermal_match,
+ },
+ .probe = loongson2_thermal_probe,
+ .remove = loongson2_thermal_remove,
+};
+module_platform_driver(loongson2_thermal_driver);
+
+MODULE_DESCRIPTION("Loongson2 thermal driver");
+MODULE_LICENSE("GPL");