[RESEND,v2] wifi: ath10k: Fix return value in ath10k_pci_init()
Commit Message
This driver is attempting to register to support two different buses.
if either of these is successful then ath10k_pci_init() should return 0
so that hardware attached to the successful bus can be probed and
supported. only if both of these are unsuccessful should ath10k_pci_init()
return an errno.
Fixes: 0b523ced9a3c ("ath10k: add basic skeleton to support ahb")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
---
v2: modify according to Jeff's suggestion, and change the commit message
and body as well.
---
drivers/net/wireless/ath/ath10k/pci.c | 20 ++++++++++++--------
1 file changed, 12 insertions(+), 8 deletions(-)
Comments
On 11/9/2022 10:19 PM, Xiu Jianfeng wrote:
> This driver is attempting to register to support two different buses.
> if either of these is successful then ath10k_pci_init() should return 0
> so that hardware attached to the successful bus can be probed and
> supported. only if both of these are unsuccessful should ath10k_pci_init()
> return an errno.
>
> Fixes: 0b523ced9a3c ("ath10k: add basic skeleton to support ahb")
> Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Xiu Jianfeng <xiujianfeng@huawei.com> wrote:
> This driver is attempting to register to support two different buses.
> if either of these is successful then ath10k_pci_init() should return 0
> so that hardware attached to the successful bus can be probed and
> supported. only if both of these are unsuccessful should ath10k_pci_init()
> return an errno.
>
> Fixes: 0b523ced9a3c ("ath10k: add basic skeleton to support ahb")
> Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
> Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Patch applied to ath-next branch of ath.git, thanks.
2af7749047d8 wifi: ath10k: Fix return value in ath10k_pci_init()
@@ -3792,18 +3792,22 @@ static struct pci_driver ath10k_pci_driver = {
static int __init ath10k_pci_init(void)
{
- int ret;
+ int ret1, ret2;
- ret = pci_register_driver(&ath10k_pci_driver);
- if (ret)
+ ret1 = pci_register_driver(&ath10k_pci_driver);
+ if (ret1)
printk(KERN_ERR "failed to register ath10k pci driver: %d\n",
- ret);
+ ret1);
- ret = ath10k_ahb_init();
- if (ret)
- printk(KERN_ERR "ahb init failed: %d\n", ret);
+ ret2 = ath10k_ahb_init();
+ if (ret2)
+ printk(KERN_ERR "ahb init failed: %d\n", ret2);
- return ret;
+ if (ret1 && ret2)
+ return ret1;
+
+ /* registered to at least one bus */
+ return 0;
}
module_init(ath10k_pci_init);