[06/11] arm64: dts: qcom: sdm845-*: Fix up comments
Commit Message
Switch '//' comments to C-style /* */.
Make sure all multiline C-style commends begin with just '/*' with
the comment text starting on a new line.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 38 +++++++++++--------
.../boot/dts/qcom/sdm845-oneplus-common.dtsi | 5 ++-
.../boot/dts/qcom/sdm850-samsung-w737.dts | 2 +-
3 files changed, 27 insertions(+), 18 deletions(-)
@@ -120,9 +120,11 @@ lt9611_3v3: lt9611-3v3 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- // TODO: make it possible to drive same GPIO from two clients
- // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
- // enable-active-high;
+ /*
+ * TODO: make it possible to drive same GPIO from two clients
+ * gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ * enable-active-high;
+ */
};
pcie0_1p05v: pcie-0-1p05v-regulator {
@@ -133,9 +135,11 @@ pcie0_1p05v: pcie-0-1p05v-regulator {
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
- // TODO: make it possible to drive same GPIO from two clients
- // gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
- // enable-active-high;
+ /*
+ * TODO: make it possible to drive same GPIO from two clients
+ * gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
+ * enable-active-high;
+ */
};
cam0_dvdd_1v2: reg_cam0_dvdd_1v2 {
@@ -195,9 +199,11 @@ v5p0_hdmiout: v5p0-hdmiout-regulator {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <500000>;
- // TODO: make it possible to drive same GPIO from two clients
- // gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
- // enable-active-high;
+ /*
+ * TODO: make it possible to drive same GPIO from two clients
+ * gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
+ * enable-active-high;
+ */
};
vbat: vbat-regulator {
@@ -1192,7 +1198,7 @@ camera@10 {
compatible = "ovti,ov8856";
reg = <0x10>;
- // CAM0_RST_N
+ /* CAM0_RST_N */
reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&cam0_default>;
@@ -1201,7 +1207,8 @@ camera@10 {
clock-names = "xvclk";
clock-frequency = <19200000>;
- /* The &vreg_s4a_1p8 trace is powered on as a,
+ /*
+ * The &vreg_s4a_1p8 trace is powered on as a,
* so it is represented by a fixed regulator.
*
* The 2.8V vdda-supply and 1.2V vddd-supply regulators
@@ -1229,10 +1236,10 @@ &cci_i2c1 {
camera@60 {
compatible = "ovti,ov7251";
- // I2C address as per ov7251.txt linux documentation
+ /* I2C address as per ov7251.txt linux documentation */
reg = <0x60>;
- // CAM3_RST_N
+ /* CAM3_RST_N */
enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&cam3_default>;
@@ -1241,7 +1248,8 @@ camera@60 {
clock-names = "xclk";
clock-frequency = <24000000>;
- /* The &vreg_s4a_1p8 trace always powered on.
+ /*
+ * The &vreg_s4a_1p8 trace always powered on.
*
* The 2.8V vdda-supply regulator is enabled when the
* vreg_s4a_1p8 trace is pulled high.
@@ -1257,7 +1265,7 @@ camera@60 {
port {
ov7251_ep: endpoint {
data-lanes = <0 1>;
-// remote-endpoint = <&csiphy3_ep>;
+/* remote-endpoint = <&csiphy3_ep>; */
};
};
};
@@ -50,7 +50,8 @@ key-vol-up {
};
reserved-memory {
- /* The rmtfs_mem needs to be guarded due to "XPU limitations"
+ /*
+ * The rmtfs_mem needs to be guarded due to "XPU limitations"
* it is otherwise possible for an allocation adjacent to the
* rmtfs_mem region to trigger an XPU violation, causing a crash.
*/
@@ -433,7 +434,7 @@ &mdss {
status = "okay";
};
-/* Modem/wifi*/
+/* Modem/wifi */
&mss_pil {
status = "okay";
firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
@@ -43,7 +43,7 @@ chosen {
#size-cells = <2>;
ranges;
- // Firmware initialized the display at 1280p instead of 1440p
+ /* Firmware initialized the display at 1280p instead of 1440p */
framebuffer0: framebuffer@80400000 {
compatible = "simple-framebuffer";
reg = <0 0x80400000 0 (1920 * 1280 * 4)>;