[v11,1/2] drivers/coresight: Add UltraSoc System Memory Buffer driver
Commit Message
From: Qi Liu <liuqi115@huawei.com>
This patch adds driver for UltraSoc SMB(System Memory Buffer)
device. SMB provides a way to buffer messages from ETM, and
store these "CPU instructions trace" in system memory.
SMB is developed by UltraSoc technology, which is acquired by
Siemens, and we still use "UltraSoc" to name driver.
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Junhao He <hejunhao3@huawei.com>
Tested-by: JunHao He <hejunhao3@huawei.com>
---
drivers/hwtracing/coresight/Kconfig | 11 +
drivers/hwtracing/coresight/Makefile | 1 +
drivers/hwtracing/coresight/ultrasoc-smb.c | 631 +++++++++++++++++++++
drivers/hwtracing/coresight/ultrasoc-smb.h | 113 ++++
4 files changed, 756 insertions(+)
create mode 100644 drivers/hwtracing/coresight/ultrasoc-smb.c
create mode 100644 drivers/hwtracing/coresight/ultrasoc-smb.h
Comments
On Mon, 7 Nov 2022 21:06:23 +0800
Junhao He <hejunhao3@huawei.com> wrote:
> From: Qi Liu <liuqi115@huawei.com>
>
> This patch adds driver for UltraSoc SMB(System Memory Buffer)
> device. SMB provides a way to buffer messages from ETM, and
> store these "CPU instructions trace" in system memory.
>
> SMB is developed by UltraSoc technology, which is acquired by
> Siemens, and we still use "UltraSoc" to name driver.
>
> Signed-off-by: Qi Liu <liuqi115@huawei.com>
> Signed-off-by: Junhao He <hejunhao3@huawei.com>
> Tested-by: JunHao He <hejunhao3@huawei.com>
Hi JunHao,
It's been a while since I last looked at this driver, so I may have
forgotten or missed previous discussions.
All the comments inline are fairly superficial and mostly concerned
with making the code easy to review / maintain rather than correctness.
Jonathan
> ---
> drivers/hwtracing/coresight/Kconfig | 11 +
> drivers/hwtracing/coresight/Makefile | 1 +
> drivers/hwtracing/coresight/ultrasoc-smb.c | 631 +++++++++++++++++++++
> drivers/hwtracing/coresight/ultrasoc-smb.h | 113 ++++
> 4 files changed, 756 insertions(+)
> create mode 100644 drivers/hwtracing/coresight/ultrasoc-smb.c
> create mode 100644 drivers/hwtracing/coresight/ultrasoc-smb.h
>
> diff --git a/drivers/hwtracing/coresight/Kconfig b/drivers/hwtracing/coresight/Kconfig
> index 45c1eb5dfcb7..05d791cb05e3 100644
> --- a/drivers/hwtracing/coresight/Kconfig
> +++ b/drivers/hwtracing/coresight/Kconfig
> @@ -201,4 +201,15 @@ config CORESIGHT_TRBE
>
> To compile this driver as a module, choose M here: the module will be
> called coresight-trbe.
> +
> +config ULTRASOC_SMB
> + tristate "Ultrasoc system memory buffer drivers"
> + depends on ACPI && ARM64 && CORESIGHT_LINKS_AND_SINKS
Can you relax this at all in the interests of getting better CI build coverage
from random configs etc.
From a quick look, I think you can safely drop the ACPI dependency on basis
relevant functions are stubbed out in acpi.h
However, it looks like coresight more generally uses such depends, so perhaps
better to just leave them here for consistency.
> + help
> + This driver provides support for the Ultrasoc system memory buffer (SMB).
> + SMB is responsible for receiving the trace data from Coresight ETM devices
> + and storing them to a system buffer.
> +
> + To compile this driver as a module, choose M here: the module will be
> + called ultrasoc-smb.
> endif
> diff --git a/drivers/hwtracing/coresight/ultrasoc-smb.c b/drivers/hwtracing/coresight/ultrasoc-smb.c
> new file mode 100644
> index 000000000000..7fe8bf9623e8
> --- /dev/null
> +++ b/drivers/hwtracing/coresight/ultrasoc-smb.c
> @@ -0,0 +1,631 @@
...
> +
> +static void smb_buffer_sync_status(struct smb_drv_data *drvdata)
> +{
> + struct smb_data_buffer *sdb = &drvdata->sdb;
> +
> + sdb->wr_offset = readl(drvdata->base + SMB_LB_WR_ADDR) - sdb->start_addr;
> + sdb->rd_offset = readl(drvdata->base + SMB_LB_RD_ADDR) - sdb->start_addr;
> + if (sdb->wr_offset == sdb->rd_offset && !smb_buffer_is_empty(drvdata))
> + sdb->full = true;
> + else
> + sdb->full = false;
Could do as
sdb->full = sdb->wr_offset == sdb->rd_offset && !smb_buffer_is_empty(drvdata);
up to you on which you think is more readable.
> +}
> +
> +static struct attribute *smb_sink_attrs[] = {
> + coresight_simple_reg32(read_pos, SMB_LB_RD_ADDR),
> + coresight_simple_reg32(write_pos, SMB_LB_WR_ADDR),
> + coresight_simple_reg32(buf_status, SMB_LB_INT_STS),
> + &dev_attr_buf_size.attr,
> + NULL,
As below.
> +};
> +
> +static const struct attribute_group smb_sink_group = {
> + .attrs = smb_sink_attrs,
> + .name = "mgmt",
> +};
> +
> +static const struct attribute_group *smb_sink_groups[] = {
> + &smb_sink_group,
> + NULL,
Generally no comma after a NULL terminator. Having a comma
implies it may make sense to put something after it, which is never
the case for these.
> +};
> +
...
> +static void smb_sync_perf_buffer(struct smb_drv_data *drvdata,
> + struct cs_buffers *buf,
> + unsigned long head,
> + unsigned long data_size)
> +{
> + struct smb_data_buffer *sdb = &drvdata->sdb;
> + char **dst_pages = (char **)buf->data_pages;
Do you need the cast? It's void ** so implicit cast should work I think.
char **dst_pages = buf->data_pages;
> + unsigned long to_copy;
> + long pg_idx, pg_offset;
> +
> + pg_idx = head >> PAGE_SHIFT;
> + pg_offset = head & (PAGE_SIZE - 1);
> +
> + while (data_size) {
> + unsigned long pg_space = PAGE_SIZE - pg_offset;
> +
> + /* Copy parts of trace data when read pointer wrap around */
> + if (sdb->rd_offset + pg_space > sdb->buf_size)
> + to_copy = sdb->buf_size - sdb->rd_offset;
> + else
> + to_copy = min(data_size, pg_space);
> +
> + memcpy(dst_pages[pg_idx] + pg_offset,
> + sdb->buf_base + sdb->rd_offset, to_copy);
> +
> + pg_offset += to_copy;
> + if (pg_offset >= PAGE_SIZE) {
> + pg_offset = 0;
> + pg_idx++;
> + pg_idx %= buf->nr_pages;
> + }
> + data_size -= to_copy;
> + sdb->rd_offset += to_copy;
> + sdb->rd_offset %= sdb->buf_size;
> + }
> +
> + sdb->data_size = 0;
> + writel(sdb->start_addr + sdb->rd_offset, drvdata->base + SMB_LB_RD_ADDR);
> +
> + /*
> + * Data remained in link cannot be purged when SMB is full, so
> + * synchronize the read pointer to write pointer, to make sure
> + * these remained data won't influence next trace.
> + */
> + if (sdb->full) {
> + smb_purge_data(drvdata);
> + writel(readl(drvdata->base + SMB_LB_WR_ADDR),
> + drvdata->base + SMB_LB_RD_ADDR);
> + }
> + smb_reset_buffer_status(drvdata);
> +}
...
> +
> +static void smb_init_hw(struct smb_drv_data *drvdata)
> +{
> + /* First disable smb and clear the status of SMB buffer */
Check for consistency in capitalization of SMB in all comments.
> + smb_reset_buffer_status(drvdata);
> + smb_disable_hw(drvdata);
> + smb_purge_data(drvdata);
> +
> + writel(SMB_BUF_CFG_STREAMING, drvdata->base + SMB_LB_CFG_LO);
> + writel(SMB_MSG_FILTER, drvdata->base + SMB_LB_CFG_HI);
> + writel(SMB_GLOBAL_CFG, drvdata->base + SMB_CFG_REG);
> + writel(SMB_GLB_INT_CFG, drvdata->base + SMB_GLOBAL_INT);
> + writel(SMB_BUF_INT_CFG, drvdata->base + SMB_LB_INT_CTRL);
> +}
> +
...
> +static int smb_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct smb_drv_data *drvdata;
> + int ret;
> +
> + drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL);
> + if (!drvdata)
> + return -ENOMEM;
> +
> + drvdata->base = devm_platform_ioremap_resource(pdev, SMB_BASE_ADDR_RES);
> + if (IS_ERR(drvdata->base)) {
> + dev_err(dev, "Failed to ioremap resource\n");
> + return PTR_ERR(drvdata->base);
> + }
> +
> + ret = smb_init_data_buffer(pdev, &drvdata->sdb);
> + if (ret) {
> + dev_err(dev, "Failed to init buffer, ret = %d\n", ret);
> + return ret;
> + }
> +
> + smb_init_hw(drvdata);
> + mutex_init(&drvdata->mutex);
> + drvdata->pid = -1;
> +
> + ret = smb_register_sink(pdev, drvdata);
> + if (ret) {
> + dev_err(dev, "Failed to register smb sink\n");
> + return ret;
> + }
> +
> + ret = smb_config_inport(dev, true);
> + if (ret) {
> + smb_unregister_sink(drvdata);
> + return ret;
> + }
> +
> + platform_set_drvdata(pdev, drvdata);
> + return 0;
> +}
> +
> +static int smb_remove(struct platform_device *pdev)
> +{
> + struct smb_drv_data *drvdata = platform_get_drvdata(pdev);
> + int ret;
> +
> + ret = smb_config_inport(&pdev->dev, false);
> + if (ret)
> + return ret;
> +
> + smb_unregister_sink(drvdata);
Trivial: I find a blank line before plane returns like this helps
a little with readability. Up to you though!
> + return 0;
> +}
> +
> +static const struct acpi_device_id ultrasoc_smb_acpi_match[] = {
> + {"HISI03A1", 0},
> + {},
Trivial, but little point in a trailing comma on a NULL terminator.
{}
};
is normally fine - note this is a bit subsystem specific so maintainer
may say otherwise.
> +};
> +MODULE_DEVICE_TABLE(acpi, ultrasoc_smb_acpi_match);
> +
> +static struct platform_driver smb_driver = {
> + .driver = {
> + .name = "ultrasoc-smb",
> + .acpi_match_table = ACPI_PTR(ultrasoc_smb_acpi_match),
> + .suppress_bind_attrs = true,
> + },
> + .probe = smb_probe,
> + .remove = smb_remove,
> +};
> +module_platform_driver(smb_driver);
> +
> +MODULE_DESCRIPTION("UltraSoc SMB CoreSight driver");
> +MODULE_LICENSE("Dual MIT/GPL");
> +MODULE_AUTHOR("Jonathan Zhou <jonathan.zhouwen@huawei.com>");
> +MODULE_AUTHOR("Qi Liu <liuqi115@huawei.com>");
> diff --git a/drivers/hwtracing/coresight/ultrasoc-smb.h b/drivers/hwtracing/coresight/ultrasoc-smb.h
> new file mode 100644
> index 000000000000..56170e1a883d
> --- /dev/null
> +++ b/drivers/hwtracing/coresight/ultrasoc-smb.h
> @@ -0,0 +1,113 @@
> +/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
> +/*
> + * Siemens System Memory Buffer driver.
> + * Copyright(c) 2022, HiSilicon Limited.
> + */
> +
> +#ifndef _ULTRASOC_SMB_H
> +#define _ULTRASOC_SMB_H
> +
> +#include <linux/coresight.h>
I think you could move this down into the c files and provide
a forwards definition of struct coresight device
Always good to keep scope of includes to minimum necessary.
> +#include <linux/miscdevice.h>
> +#include <linux/mutex.h>
> +
> +/* Offset of SMB logical buffer registers */
> +#define SMB_CFG_REG 0x00
To avoid any naming confusion I would postfix all the register
addresses with _REG
Then rethink the naming so the field names make it clear which
register they are in.
> +#define SMB_GLOBAL_EN 0x04
> +#define SMB_GLOBAL_INT 0x08
> +#define SMB_LB_CFG_LO 0x40
> +#define SMB_LB_CFG_HI 0x44
> +#define SMB_LB_INT_CTRL 0x48
> +#define SMB_LB_INT_STS 0x4c
> +#define SMB_LB_LIMIT 0x58
> +#define SMB_LB_RD_ADDR 0x5c
> +#define SMB_LB_WR_ADDR 0x60
> +#define SMB_LB_PURGE 0x64
> +
> +/* Set SMB_CFG_REG register */
> +#define SMB_BURST_LEN GENMASK(7, 4)
> +#define SMB_IDLE_PRD GENMASK(15, 12)
> +#define SMB_MEM_WR GENMASK(17, 16)
> +#define SMB_MEM_RD (GENMASK(26, 25) | GENMASK(23, 22))
Are these masks, or default values? Ideally express them as
a field mask then the value via FIELD_PREP
e.g.
#define SMB_CFG_BURST_LEN_MSK GENMASK(7, 4)
#define SMB_GLOBAL_CFG_DEFAULT ... | FIELD_PREP(SMB_CFG_BURST_LEN_MSK, 0xf) | etc
> +#define SMB_GLOBAL_CFG (SMB_IDLE_PRD | SMB_MEM_WR | SMB_MEM_RD | \
> + SMB_BURST_LEN)
> +
> +/* Set SMB_GLOBAL_INT register */
> +#define SMB_INT_EN BIT(0)
> +#define SMB_INT_TYPE_PULSE BIT(1)
> +#define SMB_INT_POLARITY_HIGH BIT(2)
> +#define SMB_GLB_INT_CFG (SMB_INT_EN | SMB_INT_TYPE_PULSE | \
> + SMB_INT_POLARITY_HIGH)
> +
> +/* Set SMB_LB_CFG_LO register */
> +#define SMB_BUF_EN BIT(0)
> +#define SMB_BUF_SINGLE_END BIT(1)
> +#define SMB_BUF_INIT BIT(8)
> +#define SMB_BUF_CONTINUOUS BIT(11)
> +#define SMB_FILTER_FLOW GENMASK(19, 16)
> +#define SMB_BUF_CFG_STREAMING (SMB_BUF_INIT | SMB_BUF_CONTINUOUS | \
> + SMB_FILTER_FLOW | SMB_BUF_SINGLE_END | \
> + SMB_BUF_EN)
> +
> +#define SMB_BASE_LOW_MASK GENMASK(31, 0)
> +
> +/* Set SMB_LB_CFG_HI register */
> +#define SMB_MSG_FILTER GENMASK(15, 8)
> +
> +/* Set SMB_LB_INT_CTRL */
> +#define SMB_BUF_INT_EN BIT(0)
> +#define SMB_BUF_NOTE_MASK GENMASK(11, 8)
> +#define SMB_BUF_INT_CFG (SMB_BUF_INT_EN | SMB_BUF_NOTE_MASK)
> +
> +#define SMB_BUF_NOT_EMPTY BIT(0)
> +#define SMB_RESET_BUF_STS GENMASK(3, 0)
> +#define SMB_PURGED BIT(0)
> +#define SMB_HW_ENABLE BIT(0)
It is useful to give fields names that reflect which register they are in.
Perhaps
SMB_GLOBAL_EN_HW_ENABLE for this one.
> +
> +#define SMB_BASE_ADDR_RES 0
> +#define SMB_BUF_INFO_RES 1
> +
> +/**
> + * struct smb_data_buffer - Details of the buffer used by SMB
> + * @buf_base: Memory mapped base address of SMB.
> + * @start_addr: SMB buffer start Physical address.
> + * @buf_size: Size of the buffer.
> + * @data_size: Size of Trace data copy to userspace.
> + * @rd_offset: Offset of the read pointer in the buffer.
> + * @wr_offset: Offset of the write pointer in the buffer.
> + * @status: Status of SMB buffer.
Naming wrong.
> + */
> +struct smb_data_buffer {
> + void __iomem *buf_base;
> + u32 start_addr;
> + unsigned long buf_size;
> + unsigned long data_size;
> + unsigned long rd_offset;
> + unsigned long wr_offset;
> + bool full;
> +};
> +
> +/**
> + * struct smb_drv_data - specifics associated to an SMB component
> + * @base: Memory mapped base address for SMB component.
> + * @csdev: Component vitals needed by the framework.
> + * @sdb: Data buffer for SMB.
> + * @miscdev: Specifics to handle "/dev/xyz.smb" entry.
> + * @mutex: Control data access to one at a time.
> + * @reading: Synchronise user space access to SMB buffer.
> + * @pid: Process ID of the process being monitored by the
> + * session that is using this component.
> + * @mode: how this SMB is being used, perf mode or sysfs mode.
> + */
> +struct smb_drv_data {
> + void __iomem *base;
> + struct coresight_device *csdev;
> + struct smb_data_buffer sdb;
> + struct miscdevice miscdev;
> + struct mutex mutex;
> + local_t reading;
> + pid_t pid;
> + u32 mode;
> +};
> +
> +#endif
Hi Jonathan,
Thanks for your comments.
On 2022/11/7 22:30, Jonathan Cameron wrote:
> On Mon, 7 Nov 2022 21:06:23 +0800
> Junhao He <hejunhao3@huawei.com> wrote:
>
>> From: Qi Liu <liuqi115@huawei.com>
>>
>> This patch adds driver for UltraSoc SMB(System Memory Buffer)
>> device. SMB provides a way to buffer messages from ETM, and
>> store these "CPU instructions trace" in system memory.
>>
>> SMB is developed by UltraSoc technology, which is acquired by
>> Siemens, and we still use "UltraSoc" to name driver.
>>
>> Signed-off-by: Qi Liu <liuqi115@huawei.com>
>> Signed-off-by: Junhao He <hejunhao3@huawei.com>
>> Tested-by: JunHao He <hejunhao3@huawei.com>
> Hi JunHao,
>
> It's been a while since I last looked at this driver, so I may have
> forgotten or missed previous discussions.
>
> All the comments inline are fairly superficial and mostly concerned
> with making the code easy to review / maintain rather than correctness.
>
> Jonathan
Yes, I will do that.
Junhao.
>> ---
>> drivers/hwtracing/coresight/Kconfig | 11 +
>> drivers/hwtracing/coresight/Makefile | 1 +
>> drivers/hwtracing/coresight/ultrasoc-smb.c | 631 +++++++++++++++++++++
>> drivers/hwtracing/coresight/ultrasoc-smb.h | 113 ++++
>> 4 files changed, 756 insertions(+)
>> create mode 100644 drivers/hwtracing/coresight/ultrasoc-smb.c
>> create mode 100644 drivers/hwtracing/coresight/ultrasoc-smb.h
>>
>> diff --git a/drivers/hwtracing/coresight/Kconfig b/drivers/hwtracing/coresight/Kconfig
>> index 45c1eb5dfcb7..05d791cb05e3 100644
>> --- a/drivers/hwtracing/coresight/Kconfig
>> +++ b/drivers/hwtracing/coresight/Kconfig
>> @@ -201,4 +201,15 @@ config CORESIGHT_TRBE
>>
>> To compile this driver as a module, choose M here: the module will be
>> called coresight-trbe.
>> +
>> +config ULTRASOC_SMB
>> + tristate "Ultrasoc system memory buffer drivers"
>> + depends on ACPI && ARM64 && CORESIGHT_LINKS_AND_SINKS
> Can you relax this at all in the interests of getting better CI build coverage
> from random configs etc.
>
> >From a quick look, I think you can safely drop the ACPI dependency on basis
> relevant functions are stubbed out in acpi.h
>
> However, it looks like coresight more generally uses such depends, so perhaps
> better to just leave them here for consistency.
Ok, Will check it.
Thanks.
>> + help
>> + This driver provides support for the Ultrasoc system memory buffer (SMB).
>> + SMB is responsible for receiving the trace data from Coresight ETM devices
>> + and storing them to a system buffer.
>> +
>> + To compile this driver as a module, choose M here: the module will be
>> + called ultrasoc-smb.
>> endif
>
>> diff --git a/drivers/hwtracing/coresight/ultrasoc-smb.c b/drivers/hwtracing/coresight/ultrasoc-smb.c
>> new file mode 100644
>> index 000000000000..7fe8bf9623e8
>> --- /dev/null
>> +++ b/drivers/hwtracing/coresight/ultrasoc-smb.c
>> @@ -0,0 +1,631 @@
> ...
>
>
>> +
>> +static void smb_buffer_sync_status(struct smb_drv_data *drvdata)
>> +{
>> + struct smb_data_buffer *sdb = &drvdata->sdb;
>> +
>> + sdb->wr_offset = readl(drvdata->base + SMB_LB_WR_ADDR) - sdb->start_addr;
>> + sdb->rd_offset = readl(drvdata->base + SMB_LB_RD_ADDR) - sdb->start_addr;
>> + if (sdb->wr_offset == sdb->rd_offset && !smb_buffer_is_empty(drvdata))
>> + sdb->full = true;
>> + else
>> + sdb->full = false;
> Could do as
> sdb->full = sdb->wr_offset == sdb->rd_offset && !smb_buffer_is_empty(drvdata);
> up to you on which you think is more readable.
Ok, I will drop this "if else" block.
Thanks.
>
>> +}
>> +
>
>
>> +static struct attribute *smb_sink_attrs[] = {
>> + coresight_simple_reg32(read_pos, SMB_LB_RD_ADDR),
>> + coresight_simple_reg32(write_pos, SMB_LB_WR_ADDR),
>> + coresight_simple_reg32(buf_status, SMB_LB_INT_STS),
>> + &dev_attr_buf_size.attr,
>> + NULL,
> As below.
Sure, Will fix in next version.
Thanks.
>
>> +};
>> +
>> +static const struct attribute_group smb_sink_group = {
>> + .attrs = smb_sink_attrs,
>> + .name = "mgmt",
>> +};
>> +
>> +static const struct attribute_group *smb_sink_groups[] = {
>> + &smb_sink_group,
>> + NULL,
> Generally no comma after a NULL terminator. Having a comma
> implies it may make sense to put something after it, which is never
> the case for these.
Sure, Will fix in next version.
Thanks.
>> +};
>> +
>
> ...
>
>> +static void smb_sync_perf_buffer(struct smb_drv_data *drvdata,
>> + struct cs_buffers *buf,
>> + unsigned long head,
>> + unsigned long data_size)
>> +{
>> + struct smb_data_buffer *sdb = &drvdata->sdb;
>> + char **dst_pages = (char **)buf->data_pages;
> Do you need the cast? It's void ** so implicit cast should work I think.
> char **dst_pages = buf->data_pages;
Ok, Will fix in next version.
Thanks.
>> + unsigned long to_copy;
>> + long pg_idx, pg_offset;
>> +
>> + pg_idx = head >> PAGE_SHIFT;
>> + pg_offset = head & (PAGE_SIZE - 1);
>> +
>> + while (data_size) {
>> + unsigned long pg_space = PAGE_SIZE - pg_offset;
>> +
>> + /* Copy parts of trace data when read pointer wrap around */
>> + if (sdb->rd_offset + pg_space > sdb->buf_size)
>> + to_copy = sdb->buf_size - sdb->rd_offset;
>> + else
>> + to_copy = min(data_size, pg_space);
>> +
>> + memcpy(dst_pages[pg_idx] + pg_offset,
>> + sdb->buf_base + sdb->rd_offset, to_copy);
>> +
>> + pg_offset += to_copy;
>> + if (pg_offset >= PAGE_SIZE) {
>> + pg_offset = 0;
>> + pg_idx++;
>> + pg_idx %= buf->nr_pages;
>> + }
>> + data_size -= to_copy;
>> + sdb->rd_offset += to_copy;
>> + sdb->rd_offset %= sdb->buf_size;
>> + }
>> +
>> + sdb->data_size = 0;
>> + writel(sdb->start_addr + sdb->rd_offset, drvdata->base + SMB_LB_RD_ADDR);
>> +
>> + /*
>> + * Data remained in link cannot be purged when SMB is full, so
>> + * synchronize the read pointer to write pointer, to make sure
>> + * these remained data won't influence next trace.
>> + */
>> + if (sdb->full) {
>> + smb_purge_data(drvdata);
>> + writel(readl(drvdata->base + SMB_LB_WR_ADDR),
>> + drvdata->base + SMB_LB_RD_ADDR);
>> + }
>> + smb_reset_buffer_status(drvdata);
>> +}
>
> ...
>
>> +
>> +static void smb_init_hw(struct smb_drv_data *drvdata)
>> +{
>> + /* First disable smb and clear the status of SMB buffer */
> Check for consistency in capitalization of SMB in all comments.
Sure, Will fix in next version.
Thanks.
>
>> + smb_reset_buffer_status(drvdata);
>> + smb_disable_hw(drvdata);
>> + smb_purge_data(drvdata);
>> +
>> + writel(SMB_BUF_CFG_STREAMING, drvdata->base + SMB_LB_CFG_LO);
>> + writel(SMB_MSG_FILTER, drvdata->base + SMB_LB_CFG_HI);
>> + writel(SMB_GLOBAL_CFG, drvdata->base + SMB_CFG_REG);
>> + writel(SMB_GLB_INT_CFG, drvdata->base + SMB_GLOBAL_INT);
>> + writel(SMB_BUF_INT_CFG, drvdata->base + SMB_LB_INT_CTRL);
>> +}
>> +
>
> ...
>
>> +static int smb_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct smb_drv_data *drvdata;
>> + int ret;
>> +
>> + drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL);
>> + if (!drvdata)
>> + return -ENOMEM;
>> +
>> + drvdata->base = devm_platform_ioremap_resource(pdev, SMB_BASE_ADDR_RES);
>> + if (IS_ERR(drvdata->base)) {
>> + dev_err(dev, "Failed to ioremap resource\n");
>> + return PTR_ERR(drvdata->base);
>> + }
>> +
>> + ret = smb_init_data_buffer(pdev, &drvdata->sdb);
>> + if (ret) {
>> + dev_err(dev, "Failed to init buffer, ret = %d\n", ret);
>> + return ret;
>> + }
>> +
>> + smb_init_hw(drvdata);
>> + mutex_init(&drvdata->mutex);
>> + drvdata->pid = -1;
>> +
>> + ret = smb_register_sink(pdev, drvdata);
>> + if (ret) {
>> + dev_err(dev, "Failed to register smb sink\n");
>> + return ret;
>> + }
>> +
>> + ret = smb_config_inport(dev, true);
>> + if (ret) {
>> + smb_unregister_sink(drvdata);
>> + return ret;
>> + }
>> +
>> + platform_set_drvdata(pdev, drvdata);
>> + return 0;
>> +}
>> +
>> +static int smb_remove(struct platform_device *pdev)
>> +{
>> + struct smb_drv_data *drvdata = platform_get_drvdata(pdev);
>> + int ret;
>> +
>> + ret = smb_config_inport(&pdev->dev, false);
>> + if (ret)
>> + return ret;
>> +
>> + smb_unregister_sink(drvdata);
> Trivial: I find a blank line before plane returns like this helps
> a little with readability. Up to you though!
Ok, Will fix it.
Thanks.
>
>> + return 0;
>> +}
>> +
>> +static const struct acpi_device_id ultrasoc_smb_acpi_match[] = {
>> + {"HISI03A1", 0},
>> + {},
> Trivial, but little point in a trailing comma on a NULL terminator.
Sure, Will fix in next version.
Thanks.
>
> {}
> };
>
> is normally fine - note this is a bit subsystem specific so maintainer
> may say otherwise.
Ok, Thanks.
>
>> +};
>> +MODULE_DEVICE_TABLE(acpi, ultrasoc_smb_acpi_match);
>> +
>> +static struct platform_driver smb_driver = {
>> + .driver = {
>> + .name = "ultrasoc-smb",
>> + .acpi_match_table = ACPI_PTR(ultrasoc_smb_acpi_match),
>> + .suppress_bind_attrs = true,
>> + },
>> + .probe = smb_probe,
>> + .remove = smb_remove,
>> +};
>> +module_platform_driver(smb_driver);
>> +
>> +MODULE_DESCRIPTION("UltraSoc SMB CoreSight driver");
>> +MODULE_LICENSE("Dual MIT/GPL");
>> +MODULE_AUTHOR("Jonathan Zhou <jonathan.zhouwen@huawei.com>");
>> +MODULE_AUTHOR("Qi Liu <liuqi115@huawei.com>");
>> diff --git a/drivers/hwtracing/coresight/ultrasoc-smb.h b/drivers/hwtracing/coresight/ultrasoc-smb.h
>> new file mode 100644
>> index 000000000000..56170e1a883d
>> --- /dev/null
>> +++ b/drivers/hwtracing/coresight/ultrasoc-smb.h
>> @@ -0,0 +1,113 @@
>> +/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
>> +/*
>> + * Siemens System Memory Buffer driver.
>> + * Copyright(c) 2022, HiSilicon Limited.
>> + */
>> +
>> +#ifndef _ULTRASOC_SMB_H
>> +#define _ULTRASOC_SMB_H
>> +
>> +#include <linux/coresight.h>
> I think you could move this down into the c files and provide
> a forwards definition of struct coresight device
>
> Always good to keep scope of includes to minimum necessary.
Sure, Will fix in next version.
Thanks.
>
>> +#include <linux/miscdevice.h>
>> +#include <linux/mutex.h>
>> +
>> +/* Offset of SMB logical buffer registers */
>> +#define SMB_CFG_REG 0x00
> To avoid any naming confusion I would postfix all the register
> addresses with _REG
> Then rethink the naming so the field names make it clear which
> register they are in.
OK, I'll check all REG names.
Thanks.
>
>> +#define SMB_GLOBAL_EN 0x04
>> +#define SMB_GLOBAL_INT 0x08
>> +#define SMB_LB_CFG_LO 0x40
>> +#define SMB_LB_CFG_HI 0x44
>> +#define SMB_LB_INT_CTRL 0x48
>> +#define SMB_LB_INT_STS 0x4c
>> +#define SMB_LB_LIMIT 0x58
>> +#define SMB_LB_RD_ADDR 0x5c
>> +#define SMB_LB_WR_ADDR 0x60
>> +#define SMB_LB_PURGE 0x64
>> +
>> +/* Set SMB_CFG_REG register */
>> +#define SMB_BURST_LEN GENMASK(7, 4)
>> +#define SMB_IDLE_PRD GENMASK(15, 12)
>> +#define SMB_MEM_WR GENMASK(17, 16)
>> +#define SMB_MEM_RD (GENMASK(26, 25) | GENMASK(23, 22))
> Are these masks, or default values? Ideally express them as
> a field mask then the value via FIELD_PREP
>
> e.g.
> #define SMB_CFG_BURST_LEN_MSK GENMASK(7, 4)
> #define SMB_GLOBAL_CFG_DEFAULT ... | FIELD_PREP(SMB_CFG_BURST_LEN_MSK, 0xf) | etc
Sure, I will do that.
Thanks.
>
>
>> +#define SMB_GLOBAL_CFG (SMB_IDLE_PRD | SMB_MEM_WR | SMB_MEM_RD | \
>> + SMB_BURST_LEN)
>> +
>> +/* Set SMB_GLOBAL_INT register */
>> +#define SMB_INT_EN BIT(0)
>> +#define SMB_INT_TYPE_PULSE BIT(1)
>> +#define SMB_INT_POLARITY_HIGH BIT(2)
>> +#define SMB_GLB_INT_CFG (SMB_INT_EN | SMB_INT_TYPE_PULSE | \
>> + SMB_INT_POLARITY_HIGH)
>> +
>> +/* Set SMB_LB_CFG_LO register */
>> +#define SMB_BUF_EN BIT(0)
>> +#define SMB_BUF_SINGLE_END BIT(1)
>> +#define SMB_BUF_INIT BIT(8)
>> +#define SMB_BUF_CONTINUOUS BIT(11)
>> +#define SMB_FILTER_FLOW GENMASK(19, 16)
>> +#define SMB_BUF_CFG_STREAMING (SMB_BUF_INIT | SMB_BUF_CONTINUOUS | \
>> + SMB_FILTER_FLOW | SMB_BUF_SINGLE_END | \
>> + SMB_BUF_EN)
>> +
>> +#define SMB_BASE_LOW_MASK GENMASK(31, 0)
>> +
>> +/* Set SMB_LB_CFG_HI register */
>> +#define SMB_MSG_FILTER GENMASK(15, 8)
>> +
>> +/* Set SMB_LB_INT_CTRL */
>> +#define SMB_BUF_INT_EN BIT(0)
>> +#define SMB_BUF_NOTE_MASK GENMASK(11, 8)
>> +#define SMB_BUF_INT_CFG (SMB_BUF_INT_EN | SMB_BUF_NOTE_MASK)
>> +
>> +#define SMB_BUF_NOT_EMPTY BIT(0)
>> +#define SMB_RESET_BUF_STS GENMASK(3, 0)
>> +#define SMB_PURGED BIT(0)
>> +#define SMB_HW_ENABLE BIT(0)
> It is useful to give fields names that reflect which register they are in.
> Perhaps
> SMB_GLOBAL_EN_HW_ENABLE for this one.
Sure, I will do that.
Thanks.
>
>> +
>> +#define SMB_BASE_ADDR_RES 0
>> +#define SMB_BUF_INFO_RES 1
>> +
>> +/**
>> + * struct smb_data_buffer - Details of the buffer used by SMB
>> + * @buf_base: Memory mapped base address of SMB.
>> + * @start_addr: SMB buffer start Physical address.
>> + * @buf_size: Size of the buffer.
>> + * @data_size: Size of Trace data copy to userspace.
>> + * @rd_offset: Offset of the read pointer in the buffer.
>> + * @wr_offset: Offset of the write pointer in the buffer.
>> + * @status: Status of SMB buffer.
> Naming wrong.
Sure, Will fix in next version.
Thanks.
>
>> + */
>> +struct smb_data_buffer {
>> + void __iomem *buf_base;
>> + u32 start_addr;
>> + unsigned long buf_size;
>> + unsigned long data_size;
>> + unsigned long rd_offset;
>> + unsigned long wr_offset;
>> + bool full;
>> +};
>> +
>> +/**
>> + * struct smb_drv_data - specifics associated to an SMB component
>> + * @base: Memory mapped base address for SMB component.
>> + * @csdev: Component vitals needed by the framework.
>> + * @sdb: Data buffer for SMB.
>> + * @miscdev: Specifics to handle "/dev/xyz.smb" entry.
>> + * @mutex: Control data access to one at a time.
>> + * @reading: Synchronise user space access to SMB buffer.
>> + * @pid: Process ID of the process being monitored by the
>> + * session that is using this component.
>> + * @mode: how this SMB is being used, perf mode or sysfs mode.
>> + */
>> +struct smb_drv_data {
>> + void __iomem *base;
>> + struct coresight_device *csdev;
>> + struct smb_data_buffer sdb;
>> + struct miscdevice miscdev;
>> + struct mutex mutex;
>> + local_t reading;
>> + pid_t pid;
>> + u32 mode;
>> +};
>> +
>> +#endif
> .
>
Best regards,
Junhao.
@@ -201,4 +201,15 @@ config CORESIGHT_TRBE
To compile this driver as a module, choose M here: the module will be
called coresight-trbe.
+
+config ULTRASOC_SMB
+ tristate "Ultrasoc system memory buffer drivers"
+ depends on ACPI && ARM64 && CORESIGHT_LINKS_AND_SINKS
+ help
+ This driver provides support for the Ultrasoc system memory buffer (SMB).
+ SMB is responsible for receiving the trace data from Coresight ETM devices
+ and storing them to a system buffer.
+
+ To compile this driver as a module, choose M here: the module will be
+ called ultrasoc-smb.
endif
@@ -27,3 +27,4 @@ obj-$(CONFIG_CORESIGHT_CTI) += coresight-cti.o
obj-$(CONFIG_CORESIGHT_TRBE) += coresight-trbe.o
coresight-cti-y := coresight-cti-core.o coresight-cti-platform.o \
coresight-cti-sysfs.o
+obj-$(CONFIG_ULTRASOC_SMB) += ultrasoc-smb.o
new file mode 100644
@@ -0,0 +1,631 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Siemens System Memory Buffer driver.
+ * Copyright(c) 2022, HiSilicon Limited.
+ */
+
+#include <linux/atomic.h>
+#include <linux/acpi.h>
+#include <linux/circ_buf.h>
+#include <linux/err.h>
+#include <linux/fs.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+
+#include "coresight-etm-perf.h"
+#include "coresight-priv.h"
+#include "ultrasoc-smb.h"
+
+DEFINE_CORESIGHT_DEVLIST(sink_devs, "ultra_smb");
+
+#define ULTRASOC_SMB_DSM_UUID "82ae1283-7f6a-4cbe-aa06-53e8fb24db18"
+
+static bool smb_buffer_is_empty(struct smb_drv_data *drvdata)
+{
+ u32 buf_status = readl(drvdata->base + SMB_LB_INT_STS);
+
+ return !(buf_status & SMB_BUF_NOT_EMPTY);
+}
+
+static void smb_buffer_sync_status(struct smb_drv_data *drvdata)
+{
+ struct smb_data_buffer *sdb = &drvdata->sdb;
+
+ sdb->wr_offset = readl(drvdata->base + SMB_LB_WR_ADDR) - sdb->start_addr;
+ sdb->rd_offset = readl(drvdata->base + SMB_LB_RD_ADDR) - sdb->start_addr;
+ if (sdb->wr_offset == sdb->rd_offset && !smb_buffer_is_empty(drvdata))
+ sdb->full = true;
+ else
+ sdb->full = false;
+}
+
+static void smb_reset_buffer_status(struct smb_drv_data *drvdata)
+{
+ writel(SMB_RESET_BUF_STS, drvdata->base + SMB_LB_INT_STS);
+}
+
+/* Purge data remaining in hardware path in case them influence next trace */
+static void smb_purge_data(struct smb_drv_data *drvdata)
+{
+ writel(SMB_PURGED, drvdata->base + SMB_LB_PURGE);
+}
+
+static void smb_update_data_size(struct smb_drv_data *drvdata)
+{
+ struct smb_data_buffer *sdb = &drvdata->sdb;
+
+ smb_purge_data(drvdata);
+ smb_buffer_sync_status(drvdata);
+ if (sdb->full) {
+ sdb->data_size = sdb->buf_size;
+ return;
+ }
+
+ sdb->data_size = CIRC_CNT(sdb->wr_offset, sdb->rd_offset, sdb->buf_size);
+}
+
+static int smb_open(struct inode *inode, struct file *file)
+{
+ struct smb_drv_data *drvdata = container_of(file->private_data,
+ struct smb_drv_data, miscdev);
+ int ret = 0;
+
+ mutex_lock(&drvdata->mutex);
+
+ if (local_read(&drvdata->reading)) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ if (atomic_read(drvdata->csdev->refcnt)) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ local_set(&drvdata->reading, 1);
+out:
+ mutex_unlock(&drvdata->mutex);
+ return ret;
+}
+
+static ssize_t smb_read(struct file *file, char __user *data, size_t len,
+ loff_t *ppos)
+{
+ struct smb_drv_data *drvdata = container_of(file->private_data,
+ struct smb_drv_data, miscdev);
+ struct smb_data_buffer *sdb = &drvdata->sdb;
+ struct device *dev = &drvdata->csdev->dev;
+ ssize_t to_copy = 0;
+
+ mutex_lock(&drvdata->mutex);
+
+ if (!sdb->data_size) {
+ smb_update_data_size(drvdata);
+ if (!sdb->data_size)
+ goto out;
+ }
+
+ to_copy = min(sdb->data_size, len);
+
+ /* Copy parts of trace data when read pointer wrap around SMB buffer */
+ if (sdb->rd_offset + to_copy > sdb->buf_size)
+ to_copy = sdb->buf_size - sdb->rd_offset;
+
+ if (copy_to_user(data, (void *)sdb->buf_base + sdb->rd_offset,
+ to_copy)) {
+ dev_dbg(dev, "Failed to copy data to user\n");
+ to_copy = -EFAULT;
+ goto out;
+ }
+
+ *ppos += to_copy;
+ sdb->data_size -= to_copy;
+ sdb->rd_offset += to_copy;
+ sdb->rd_offset %= sdb->buf_size;
+ writel(sdb->start_addr + sdb->rd_offset,
+ drvdata->base + SMB_LB_RD_ADDR);
+ dev_dbg(dev, "%zu bytes copied\n", to_copy);
+out:
+ if (!sdb->data_size)
+ smb_reset_buffer_status(drvdata);
+ mutex_unlock(&drvdata->mutex);
+ return to_copy;
+}
+
+static int smb_release(struct inode *inode, struct file *file)
+{
+ struct smb_drv_data *drvdata = container_of(file->private_data,
+ struct smb_drv_data, miscdev);
+
+ mutex_lock(&drvdata->mutex);
+ local_set(&drvdata->reading, 0);
+ mutex_unlock(&drvdata->mutex);
+
+ return 0;
+}
+
+static const struct file_operations smb_fops = {
+ .owner = THIS_MODULE,
+ .open = smb_open,
+ .read = smb_read,
+ .release = smb_release,
+ .llseek = no_llseek,
+};
+
+static ssize_t buf_size_show(struct device *dev, struct device_attribute *attr,
+ char *buf)
+{
+ struct smb_drv_data *drvdata = dev_get_drvdata(dev->parent);
+
+ return sysfs_emit(buf, "0x%lx\n", drvdata->sdb.buf_size);
+}
+static DEVICE_ATTR_RO(buf_size);
+
+static struct attribute *smb_sink_attrs[] = {
+ coresight_simple_reg32(read_pos, SMB_LB_RD_ADDR),
+ coresight_simple_reg32(write_pos, SMB_LB_WR_ADDR),
+ coresight_simple_reg32(buf_status, SMB_LB_INT_STS),
+ &dev_attr_buf_size.attr,
+ NULL,
+};
+
+static const struct attribute_group smb_sink_group = {
+ .attrs = smb_sink_attrs,
+ .name = "mgmt",
+};
+
+static const struct attribute_group *smb_sink_groups[] = {
+ &smb_sink_group,
+ NULL,
+};
+
+static void smb_enable_hw(struct smb_drv_data *drvdata)
+{
+ writel(SMB_HW_ENABLE, drvdata->base + SMB_GLOBAL_EN);
+}
+
+static void smb_disable_hw(struct smb_drv_data *drvdata)
+{
+ writel(0x0, drvdata->base + SMB_GLOBAL_EN);
+}
+
+static void smb_enable_sysfs(struct coresight_device *csdev)
+{
+ struct smb_drv_data *drvdata = dev_get_drvdata(csdev->dev.parent);
+
+ if (drvdata->mode != CS_MODE_DISABLED)
+ return;
+
+ smb_enable_hw(drvdata);
+ drvdata->mode = CS_MODE_SYSFS;
+}
+
+static int smb_enable_perf(struct coresight_device *csdev, void *data)
+{
+ struct smb_drv_data *drvdata = dev_get_drvdata(csdev->dev.parent);
+ struct perf_output_handle *handle = data;
+ struct cs_buffers *buf = etm_perf_sink_config(handle);
+ pid_t pid;
+
+ if (!buf)
+ return -EINVAL;
+
+ /* Get a handle on the pid of the target process */
+ pid = buf->pid;
+
+ /* Device is already in used by other session */
+ if (drvdata->pid != -1 && drvdata->pid != pid)
+ return -EBUSY;
+
+ if (drvdata->pid == -1) {
+ smb_enable_hw(drvdata);
+ drvdata->pid = pid;
+ drvdata->mode = CS_MODE_PERF;
+ }
+
+ return 0;
+}
+
+static int smb_enable(struct coresight_device *csdev, u32 mode, void *data)
+{
+ struct smb_drv_data *drvdata = dev_get_drvdata(csdev->dev.parent);
+ int ret = 0;
+
+ mutex_lock(&drvdata->mutex);
+
+ /* Do nothing, the trace data is reading by other interface now */
+ if (local_read(&drvdata->reading)) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ /* Do nothing, the SMB is already enabled as other mode */
+ if (drvdata->mode != CS_MODE_DISABLED && drvdata->mode != mode) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ switch (mode) {
+ case CS_MODE_SYSFS:
+ smb_enable_sysfs(csdev);
+ break;
+ case CS_MODE_PERF:
+ ret = smb_enable_perf(csdev, data);
+ break;
+ default:
+ ret = -EINVAL;
+ }
+
+ if (ret)
+ goto out;
+
+ atomic_inc(csdev->refcnt);
+
+ dev_dbg(&csdev->dev, "Ultrasoc SMB enabled\n");
+out:
+ mutex_unlock(&drvdata->mutex);
+ return ret;
+}
+
+static int smb_disable(struct coresight_device *csdev)
+{
+ struct smb_drv_data *drvdata = dev_get_drvdata(csdev->dev.parent);
+ int ret = 0;
+
+ mutex_lock(&drvdata->mutex);
+
+ if (local_read(&drvdata->reading)) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ if (atomic_dec_return(csdev->refcnt)) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ /* Complain if we (somehow) got out of sync */
+ WARN_ON_ONCE(drvdata->mode == CS_MODE_DISABLED);
+
+ smb_disable_hw(drvdata);
+ smb_purge_data(drvdata);
+
+ /* Dissociate from the target process. */
+ drvdata->pid = -1;
+ drvdata->mode = CS_MODE_DISABLED;
+
+ dev_dbg(&csdev->dev, "Ultrasoc SMB disabled\n");
+out:
+ mutex_unlock(&drvdata->mutex);
+ return ret;
+}
+
+static void *smb_alloc_buffer(struct coresight_device *csdev,
+ struct perf_event *event, void **pages,
+ int nr_pages, bool overwrite)
+{
+ struct cs_buffers *buf;
+ int node;
+
+ node = (event->cpu == -1) ? NUMA_NO_NODE : cpu_to_node(event->cpu);
+ buf = kzalloc_node(sizeof(struct cs_buffers), GFP_KERNEL, node);
+ if (!buf)
+ return NULL;
+
+ buf->snapshot = overwrite;
+ buf->nr_pages = nr_pages;
+ buf->data_pages = pages;
+ buf->pid = task_pid_nr(event->owner);
+
+ return buf;
+}
+
+static void smb_free_buffer(void *config)
+{
+ struct cs_buffers *buf = config;
+
+ kfree(buf);
+}
+
+static void smb_sync_perf_buffer(struct smb_drv_data *drvdata,
+ struct cs_buffers *buf,
+ unsigned long head,
+ unsigned long data_size)
+{
+ struct smb_data_buffer *sdb = &drvdata->sdb;
+ char **dst_pages = (char **)buf->data_pages;
+ unsigned long to_copy;
+ long pg_idx, pg_offset;
+
+ pg_idx = head >> PAGE_SHIFT;
+ pg_offset = head & (PAGE_SIZE - 1);
+
+ while (data_size) {
+ unsigned long pg_space = PAGE_SIZE - pg_offset;
+
+ /* Copy parts of trace data when read pointer wrap around */
+ if (sdb->rd_offset + pg_space > sdb->buf_size)
+ to_copy = sdb->buf_size - sdb->rd_offset;
+ else
+ to_copy = min(data_size, pg_space);
+
+ memcpy(dst_pages[pg_idx] + pg_offset,
+ sdb->buf_base + sdb->rd_offset, to_copy);
+
+ pg_offset += to_copy;
+ if (pg_offset >= PAGE_SIZE) {
+ pg_offset = 0;
+ pg_idx++;
+ pg_idx %= buf->nr_pages;
+ }
+ data_size -= to_copy;
+ sdb->rd_offset += to_copy;
+ sdb->rd_offset %= sdb->buf_size;
+ }
+
+ sdb->data_size = 0;
+ writel(sdb->start_addr + sdb->rd_offset, drvdata->base + SMB_LB_RD_ADDR);
+
+ /*
+ * Data remained in link cannot be purged when SMB is full, so
+ * synchronize the read pointer to write pointer, to make sure
+ * these remained data won't influence next trace.
+ */
+ if (sdb->full) {
+ smb_purge_data(drvdata);
+ writel(readl(drvdata->base + SMB_LB_WR_ADDR),
+ drvdata->base + SMB_LB_RD_ADDR);
+ }
+ smb_reset_buffer_status(drvdata);
+}
+
+static unsigned long smb_update_buffer(struct coresight_device *csdev,
+ struct perf_output_handle *handle,
+ void *sink_config)
+{
+ struct smb_drv_data *drvdata = dev_get_drvdata(csdev->dev.parent);
+ struct smb_data_buffer *sdb = &drvdata->sdb;
+ struct cs_buffers *buf = sink_config;
+ unsigned long data_size = 0;
+ bool lost = false;
+
+ if (!buf)
+ return 0;
+
+ mutex_lock(&drvdata->mutex);
+
+ /* Don't do anything if another tracer is using this sink. */
+ if (atomic_read(csdev->refcnt) != 1)
+ goto out;
+
+ smb_disable_hw(drvdata);
+ smb_update_data_size(drvdata);
+ data_size = sdb->data_size;
+
+ /*
+ * The SMB buffer may be bigger than the space available in the
+ * perf ring buffer (handle->size). If so advance the offset so
+ * that we get the latest trace data.
+ */
+ if (data_size > handle->size) {
+ sdb->rd_offset += data_size - handle->size;
+ sdb->rd_offset %= sdb->buf_size;
+ data_size = handle->size;
+ lost = true;
+ }
+
+ smb_sync_perf_buffer(drvdata, buf, handle->head, data_size);
+ if (!buf->snapshot && lost)
+ perf_aux_output_flag(handle, PERF_AUX_FLAG_TRUNCATED);
+
+ smb_enable_hw(drvdata);
+out:
+ mutex_unlock(&drvdata->mutex);
+ return data_size;
+}
+
+static const struct coresight_ops_sink smb_cs_ops = {
+ .enable = smb_enable,
+ .disable = smb_disable,
+ .alloc_buffer = smb_alloc_buffer,
+ .free_buffer = smb_free_buffer,
+ .update_buffer = smb_update_buffer,
+};
+
+static const struct coresight_ops cs_ops = {
+ .sink_ops = &smb_cs_ops,
+};
+
+static int smb_init_data_buffer(struct platform_device *pdev,
+ struct smb_data_buffer *sdb)
+{
+ struct resource *res;
+ void __iomem *base;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, SMB_BUF_INFO_RES);
+ if (IS_ERR(res)) {
+ dev_err(&pdev->dev, "SMB device failed to get resource\n");
+ return -EINVAL;
+ }
+
+ sdb->start_addr = res->start & SMB_BASE_LOW_MASK;
+ sdb->buf_size = resource_size(res);
+ if (sdb->buf_size == 0)
+ return -EINVAL;
+
+ /*
+ * This is a chunk of memory, use classic mapping with better
+ * performance.
+ */
+ base = devm_memremap(&pdev->dev, sdb->start_addr, sdb->buf_size,
+ MEMREMAP_WB);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ sdb->buf_base = base;
+
+ return 0;
+}
+
+static void smb_init_hw(struct smb_drv_data *drvdata)
+{
+ /* First disable smb and clear the status of SMB buffer */
+ smb_reset_buffer_status(drvdata);
+ smb_disable_hw(drvdata);
+ smb_purge_data(drvdata);
+
+ writel(SMB_BUF_CFG_STREAMING, drvdata->base + SMB_LB_CFG_LO);
+ writel(SMB_MSG_FILTER, drvdata->base + SMB_LB_CFG_HI);
+ writel(SMB_GLOBAL_CFG, drvdata->base + SMB_CFG_REG);
+ writel(SMB_GLB_INT_CFG, drvdata->base + SMB_GLOBAL_INT);
+ writel(SMB_BUF_INT_CFG, drvdata->base + SMB_LB_INT_CTRL);
+}
+
+static int smb_register_sink(struct platform_device *pdev,
+ struct smb_drv_data *drvdata)
+{
+ struct coresight_platform_data *pdata = NULL;
+ struct coresight_desc desc = { 0 };
+ int ret;
+
+ pdata = coresight_get_platform_data(&pdev->dev);
+ if (IS_ERR(pdata))
+ return PTR_ERR(pdata);
+
+ desc.type = CORESIGHT_DEV_TYPE_SINK;
+ desc.subtype.sink_subtype = CORESIGHT_DEV_SUBTYPE_SINK_BUFFER;
+ desc.ops = &cs_ops;
+ desc.pdata = pdata;
+ desc.dev = &pdev->dev;
+ desc.groups = smb_sink_groups;
+ desc.name = coresight_alloc_device_name(&sink_devs, &pdev->dev);
+ if (!desc.name) {
+ dev_err(&pdev->dev, "Failed to alloc coresight device name");
+ return -ENOMEM;
+ }
+ desc.access = CSDEV_ACCESS_IOMEM(drvdata->base);
+
+ drvdata->csdev = coresight_register(&desc);
+ if (IS_ERR(drvdata->csdev))
+ return PTR_ERR(drvdata->csdev);
+
+ drvdata->miscdev.name = desc.name;
+ drvdata->miscdev.minor = MISC_DYNAMIC_MINOR;
+ drvdata->miscdev.fops = &smb_fops;
+ ret = misc_register(&drvdata->miscdev);
+ if (ret) {
+ coresight_unregister(drvdata->csdev);
+ dev_err(&pdev->dev, "Failed to register misc, ret=%d\n", ret);
+ }
+
+ return ret;
+}
+
+static void smb_unregister_sink(struct smb_drv_data *drvdata)
+{
+ misc_deregister(&drvdata->miscdev);
+ coresight_unregister(drvdata->csdev);
+}
+
+static int smb_config_inport(struct device *dev, bool enable)
+{
+ u64 func = enable ? 1 : 0;
+ union acpi_object *obj;
+ guid_t guid;
+ u64 rev = 0;
+
+ /*
+ * Using DSM calls to enable/disable ultrasoc hardwares on
+ * tracing path, to prevent ultrasoc packet format being exposed.
+ */
+ if (guid_parse(ULTRASOC_SMB_DSM_UUID, &guid)) {
+ dev_err(dev, "Get GUID failed\n");
+ return -EINVAL;
+ }
+
+ obj = acpi_evaluate_dsm(ACPI_HANDLE(dev), &guid, rev, func, NULL);
+ if (!obj)
+ dev_err(dev, "ACPI handle failed\n");
+ else
+ ACPI_FREE(obj);
+
+ return 0;
+}
+
+static int smb_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct smb_drv_data *drvdata;
+ int ret;
+
+ drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL);
+ if (!drvdata)
+ return -ENOMEM;
+
+ drvdata->base = devm_platform_ioremap_resource(pdev, SMB_BASE_ADDR_RES);
+ if (IS_ERR(drvdata->base)) {
+ dev_err(dev, "Failed to ioremap resource\n");
+ return PTR_ERR(drvdata->base);
+ }
+
+ ret = smb_init_data_buffer(pdev, &drvdata->sdb);
+ if (ret) {
+ dev_err(dev, "Failed to init buffer, ret = %d\n", ret);
+ return ret;
+ }
+
+ smb_init_hw(drvdata);
+ mutex_init(&drvdata->mutex);
+ drvdata->pid = -1;
+
+ ret = smb_register_sink(pdev, drvdata);
+ if (ret) {
+ dev_err(dev, "Failed to register smb sink\n");
+ return ret;
+ }
+
+ ret = smb_config_inport(dev, true);
+ if (ret) {
+ smb_unregister_sink(drvdata);
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, drvdata);
+ return 0;
+}
+
+static int smb_remove(struct platform_device *pdev)
+{
+ struct smb_drv_data *drvdata = platform_get_drvdata(pdev);
+ int ret;
+
+ ret = smb_config_inport(&pdev->dev, false);
+ if (ret)
+ return ret;
+
+ smb_unregister_sink(drvdata);
+ return 0;
+}
+
+static const struct acpi_device_id ultrasoc_smb_acpi_match[] = {
+ {"HISI03A1", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(acpi, ultrasoc_smb_acpi_match);
+
+static struct platform_driver smb_driver = {
+ .driver = {
+ .name = "ultrasoc-smb",
+ .acpi_match_table = ACPI_PTR(ultrasoc_smb_acpi_match),
+ .suppress_bind_attrs = true,
+ },
+ .probe = smb_probe,
+ .remove = smb_remove,
+};
+module_platform_driver(smb_driver);
+
+MODULE_DESCRIPTION("UltraSoc SMB CoreSight driver");
+MODULE_LICENSE("Dual MIT/GPL");
+MODULE_AUTHOR("Jonathan Zhou <jonathan.zhouwen@huawei.com>");
+MODULE_AUTHOR("Qi Liu <liuqi115@huawei.com>");
new file mode 100644
@@ -0,0 +1,113 @@
+/* SPDX-License-Identifier: (GPL-2.0 OR MIT) */
+/*
+ * Siemens System Memory Buffer driver.
+ * Copyright(c) 2022, HiSilicon Limited.
+ */
+
+#ifndef _ULTRASOC_SMB_H
+#define _ULTRASOC_SMB_H
+
+#include <linux/coresight.h>
+#include <linux/miscdevice.h>
+#include <linux/mutex.h>
+
+/* Offset of SMB logical buffer registers */
+#define SMB_CFG_REG 0x00
+#define SMB_GLOBAL_EN 0x04
+#define SMB_GLOBAL_INT 0x08
+#define SMB_LB_CFG_LO 0x40
+#define SMB_LB_CFG_HI 0x44
+#define SMB_LB_INT_CTRL 0x48
+#define SMB_LB_INT_STS 0x4c
+#define SMB_LB_LIMIT 0x58
+#define SMB_LB_RD_ADDR 0x5c
+#define SMB_LB_WR_ADDR 0x60
+#define SMB_LB_PURGE 0x64
+
+/* Set SMB_CFG_REG register */
+#define SMB_BURST_LEN GENMASK(7, 4)
+#define SMB_IDLE_PRD GENMASK(15, 12)
+#define SMB_MEM_WR GENMASK(17, 16)
+#define SMB_MEM_RD (GENMASK(26, 25) | GENMASK(23, 22))
+#define SMB_GLOBAL_CFG (SMB_IDLE_PRD | SMB_MEM_WR | SMB_MEM_RD | \
+ SMB_BURST_LEN)
+
+/* Set SMB_GLOBAL_INT register */
+#define SMB_INT_EN BIT(0)
+#define SMB_INT_TYPE_PULSE BIT(1)
+#define SMB_INT_POLARITY_HIGH BIT(2)
+#define SMB_GLB_INT_CFG (SMB_INT_EN | SMB_INT_TYPE_PULSE | \
+ SMB_INT_POLARITY_HIGH)
+
+/* Set SMB_LB_CFG_LO register */
+#define SMB_BUF_EN BIT(0)
+#define SMB_BUF_SINGLE_END BIT(1)
+#define SMB_BUF_INIT BIT(8)
+#define SMB_BUF_CONTINUOUS BIT(11)
+#define SMB_FILTER_FLOW GENMASK(19, 16)
+#define SMB_BUF_CFG_STREAMING (SMB_BUF_INIT | SMB_BUF_CONTINUOUS | \
+ SMB_FILTER_FLOW | SMB_BUF_SINGLE_END | \
+ SMB_BUF_EN)
+
+#define SMB_BASE_LOW_MASK GENMASK(31, 0)
+
+/* Set SMB_LB_CFG_HI register */
+#define SMB_MSG_FILTER GENMASK(15, 8)
+
+/* Set SMB_LB_INT_CTRL */
+#define SMB_BUF_INT_EN BIT(0)
+#define SMB_BUF_NOTE_MASK GENMASK(11, 8)
+#define SMB_BUF_INT_CFG (SMB_BUF_INT_EN | SMB_BUF_NOTE_MASK)
+
+#define SMB_BUF_NOT_EMPTY BIT(0)
+#define SMB_RESET_BUF_STS GENMASK(3, 0)
+#define SMB_PURGED BIT(0)
+#define SMB_HW_ENABLE BIT(0)
+
+#define SMB_BASE_ADDR_RES 0
+#define SMB_BUF_INFO_RES 1
+
+/**
+ * struct smb_data_buffer - Details of the buffer used by SMB
+ * @buf_base: Memory mapped base address of SMB.
+ * @start_addr: SMB buffer start Physical address.
+ * @buf_size: Size of the buffer.
+ * @data_size: Size of Trace data copy to userspace.
+ * @rd_offset: Offset of the read pointer in the buffer.
+ * @wr_offset: Offset of the write pointer in the buffer.
+ * @status: Status of SMB buffer.
+ */
+struct smb_data_buffer {
+ void __iomem *buf_base;
+ u32 start_addr;
+ unsigned long buf_size;
+ unsigned long data_size;
+ unsigned long rd_offset;
+ unsigned long wr_offset;
+ bool full;
+};
+
+/**
+ * struct smb_drv_data - specifics associated to an SMB component
+ * @base: Memory mapped base address for SMB component.
+ * @csdev: Component vitals needed by the framework.
+ * @sdb: Data buffer for SMB.
+ * @miscdev: Specifics to handle "/dev/xyz.smb" entry.
+ * @mutex: Control data access to one at a time.
+ * @reading: Synchronise user space access to SMB buffer.
+ * @pid: Process ID of the process being monitored by the
+ * session that is using this component.
+ * @mode: how this SMB is being used, perf mode or sysfs mode.
+ */
+struct smb_drv_data {
+ void __iomem *base;
+ struct coresight_device *csdev;
+ struct smb_data_buffer sdb;
+ struct miscdevice miscdev;
+ struct mutex mutex;
+ local_t reading;
+ pid_t pid;
+ u32 mode;
+};
+
+#endif