@@ -6369,6 +6369,16 @@
in situations with strict latency requirements (where
interruptions from clocksource watchdog are not
acceptable).
+ [x86] recalibrate: force recalibration against a HW timer
+ (HPET or PM timer) on systems whose TSC frequency was
+ obtained from HW or FW using either an MSR or CPUID(0x15).
+ Warn if the difference is more than 500 ppm.
+ [x86] watchdog: Use TSC as the watchdog clocksource with
+ which to check other HW timers (HPET or PM timer), but
+ only on systems where TSC has been deemed trustworthy.
+ This will be suppressed by an earlier tsc=nowatchdog and
+ can be overridden by a later tsc=nowatchdog. A console
+ message will flag any such suppression or overriding.
tsc_early_khz= [X86] Skip early TSC calibration and use the given
value instead. Useful when the early TSC frequency discovery
@@ -33,6 +33,7 @@ Required properties:
For those SoCs that use CPUX
* "mediatek,mt6795-systimer" for MT6795 compatible timers (CPUX)
+ * "mediatek,mt8365-systimer" for MT8365 compatible timers (CPUX)
- reg: Should contain location and length for timer register.
- clocks: Should contain system clock.
new file mode 100644
@@ -0,0 +1,52 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/timer/riscv,timer.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: RISC-V timer
+
+maintainers:
+ - Anup Patel <anup@brainfault.org>
+
+description: |+
+ RISC-V platforms always have a RISC-V timer device for the supervisor-mode
+ based on the time CSR defined by the RISC-V privileged specification. The
+ timer interrupts of this device are configured using the RISC-V SBI Time
+ extension or the RISC-V Sstc extension.
+
+ The clock frequency of RISC-V timer device is specified via the
+ "timebase-frequency" DT property of "/cpus" DT node which is described
+ in Documentation/devicetree/bindings/riscv/cpus.yaml
+
+properties:
+ compatible:
+ enum:
+ - riscv,timer
+
+ interrupts-extended:
+ minItems: 1
+ maxItems: 4096 # Should be enough?
+
+ riscv,timer-cannot-wake-cpu:
+ type: boolean
+ description:
+ If present, the timer interrupt cannot wake up the CPU from one or
+ more suspend/idle states.
+
+additionalProperties: false
+
+required:
+ - compatible
+ - interrupts-extended
+
+examples:
+ - |
+ timer {
+ compatible = "riscv,timer";
+ interrupts-extended = <&cpu1intc 5>,
+ <&cpu2intc 5>,
+ <&cpu3intc 5>,
+ <&cpu4intc 5>;
+ };
+...
@@ -17,6 +17,7 @@ properties:
- items:
- enum:
- rockchip,rv1108-timer
+ - rockchip,rv1126-timer
- rockchip,rk3036-timer
- rockchip,rk3128-timer
- rockchip,rk3188-timer
@@ -20,6 +20,10 @@ description:
property of "/cpus" DT node. The "timebase-frequency" DT property is
described in Documentation/devicetree/bindings/riscv/cpus.yaml
+ T-Head C906/C910 CPU cores include an implementation of CLINT too, however
+ their implementation lacks a memory-mapped MTIME register, thus not
+ compatible with SiFive ones.
+
properties:
compatible:
oneOf:
@@ -29,6 +33,10 @@ properties:
- starfive,jh7100-clint
- canaan,k210-clint
- const: sifive,clint0
+ - items:
+ - enum:
+ - allwinner,sun20i-d1-clint
+ - const: thead,c900-clint
- items:
- const: sifive,clint0
- const: riscv,clint0
@@ -12,7 +12,6 @@ config 32BIT
config RISCV
def_bool y
- select ARCH_CLOCKSOURCE_INIT
select ARCH_ENABLE_HUGEPAGE_MIGRATION if HUGETLB_PAGE && MIGRATION
select ARCH_ENABLE_SPLIT_PMD_PTLOCK if PGTABLE_LEVELS > 2
select ARCH_HAS_BINFMT_FLAT
@@ -5,6 +5,7 @@
*/
#include <linux/of_clk.h>
+#include <linux/clockchips.h>
#include <linux/clocksource.h>
#include <linux/delay.h>
#include <asm/sbi.h>
@@ -29,13 +30,6 @@ void __init time_init(void)
of_clk_init(NULL);
timer_probe();
-}
-void clocksource_arch_init(struct clocksource *cs)
-{
-#ifdef CONFIG_GENERIC_GETTIMEOFDAY
- cs->vdso_clock_mode = VDSO_CLOCKMODE_ARCHTIMER;
-#else
- cs->vdso_clock_mode = VDSO_CLOCKMODE_NONE;
-#endif
+ tick_setup_hrtimer_broadcast();
}
@@ -8,6 +8,7 @@
extern void hpet_time_init(void);
extern void time_init(void);
extern bool pit_timer_init(void);
+extern bool tsc_clocksource_watchdog_disabled(void);
extern struct clock_event_device *global_clock_event;
@@ -1091,6 +1091,8 @@ int __init hpet_enable(void)
if (!hpet_counting())
goto out_nohpet;
+ if (tsc_clocksource_watchdog_disabled())
+ clocksource_hpet.flags |= CLOCK_SOURCE_MUST_VERIFY;
clocksource_register_hz(&clocksource_hpet, (u32)hpet_freq);
if (id & HPET_ID_LEGSUP) {
@@ -48,6 +48,8 @@ static DEFINE_STATIC_KEY_FALSE(__use_tsc);
int tsc_clocksource_reliable;
+static int __read_mostly tsc_force_recalibrate;
+
static u32 art_to_tsc_numerator;
static u32 art_to_tsc_denominator;
static u64 art_to_tsc_offset;
@@ -292,6 +294,7 @@ __setup("notsc", notsc_setup);
static int no_sched_irq_time;
static int no_tsc_watchdog;
+static int tsc_as_watchdog;
static int __init tsc_setup(char *str)
{
@@ -301,8 +304,22 @@ static int __init tsc_setup(char *str)
no_sched_irq_time = 1;
if (!strcmp(str, "unstable"))
mark_tsc_unstable("boot parameter");
- if (!strcmp(str, "nowatchdog"))
+ if (!strcmp(str, "nowatchdog")) {
no_tsc_watchdog = 1;
+ if (tsc_as_watchdog)
+ pr_alert("%s: Overriding earlier tsc=watchdog with tsc=nowatchdog\n",
+ __func__);
+ tsc_as_watchdog = 0;
+ }
+ if (!strcmp(str, "recalibrate"))
+ tsc_force_recalibrate = 1;
+ if (!strcmp(str, "watchdog")) {
+ if (no_tsc_watchdog)
+ pr_alert("%s: tsc=watchdog overridden by earlier tsc=nowatchdog\n",
+ __func__);
+ else
+ tsc_as_watchdog = 1;
+ }
return 1;
}
@@ -1186,6 +1203,12 @@ static void __init tsc_disable_clocksource_watchdog(void)
clocksource_tsc.flags &= ~CLOCK_SOURCE_MUST_VERIFY;
}
+bool tsc_clocksource_watchdog_disabled(void)
+{
+ return !(clocksource_tsc.flags & CLOCK_SOURCE_MUST_VERIFY) &&
+ tsc_as_watchdog && !no_tsc_watchdog;
+}
+
static void __init check_system_tsc_reliable(void)
{
#if defined(CONFIG_MGEODEGX1) || defined(CONFIG_MGEODE_LX) || defined(CONFIG_X86_GENERIC)
@@ -1374,6 +1397,25 @@ static void tsc_refine_calibration_work(struct work_struct *work)
else
freq = calc_pmtimer_ref(delta, ref_start, ref_stop);
+ /* Will hit this only if tsc_force_recalibrate has been set */
+ if (boot_cpu_has(X86_FEATURE_TSC_KNOWN_FREQ)) {
+
+ /* Warn if the deviation exceeds 500 ppm */
+ if (abs(tsc_khz - freq) > (tsc_khz >> 11)) {
+ pr_warn("Warning: TSC freq calibrated by CPUID/MSR differs from what is calibrated by HW timer, please check with vendor!!\n");
+ pr_info("Previous calibrated TSC freq:\t %lu.%03lu MHz\n",
+ (unsigned long)tsc_khz / 1000,
+ (unsigned long)tsc_khz % 1000);
+ }
+
+ pr_info("TSC freq recalibrated by [%s]:\t %lu.%03lu MHz\n",
+ hpet ? "HPET" : "PM_TIMER",
+ (unsigned long)freq / 1000,
+ (unsigned long)freq % 1000);
+
+ return;
+ }
+
/* Make sure we're within 1% */
if (abs(tsc_khz - freq) > tsc_khz/100)
goto out;
@@ -1407,8 +1449,10 @@ static int __init init_tsc_clocksource(void)
if (!boot_cpu_has(X86_FEATURE_TSC) || !tsc_khz)
return 0;
- if (tsc_unstable)
- goto unreg;
+ if (tsc_unstable) {
+ clocksource_unregister(&clocksource_tsc_early);
+ return 0;
+ }
if (boot_cpu_has(X86_FEATURE_NONSTOP_TSC_S3))
clocksource_tsc.flags |= CLOCK_SOURCE_SUSPEND_NONSTOP;
@@ -1421,9 +1465,10 @@ static int __init init_tsc_clocksource(void)
if (boot_cpu_has(X86_FEATURE_ART))
art_related_clocksource = &clocksource_tsc;
clocksource_register_khz(&clocksource_tsc, tsc_khz);
-unreg:
clocksource_unregister(&clocksource_tsc_early);
- return 0;
+
+ if (!tsc_force_recalibrate)
+ return 0;
}
schedule_delayed_work(&tsc_irqwork, 0);
@@ -706,7 +706,7 @@ config INGENIC_OST
config MICROCHIP_PIT64B
bool "Microchip PIT64B support"
- depends on OF || COMPILE_TEST
+ depends on OF && ARM
select TIMER_OF
help
This option enables Microchip PIT64B timer for Atmel
@@ -23,6 +23,7 @@
#include <linux/pci.h>
#include <linux/delay.h>
#include <asm/io.h>
+#include <asm/time.h>
/*
* The I/O port the PMTMR resides at.
@@ -210,8 +211,9 @@ static int __init init_acpi_pm_clocksource(void)
return -ENODEV;
}
- return clocksource_register_hz(&clocksource_acpi_pm,
- PMTMR_TICKS_PER_SEC);
+ if (tsc_clocksource_watchdog_disabled())
+ clocksource_acpi_pm.flags |= CLOCK_SOURCE_MUST_VERIFY;
+ return clocksource_register_hz(&clocksource_acpi_pm, PMTMR_TICKS_PER_SEC);
}
/* We use fs_initcall because we want the PCI fixups to have run
@@ -333,11 +333,6 @@ static int em_sti_probe(struct platform_device *pdev)
return 0;
}
-static int em_sti_remove(struct platform_device *pdev)
-{
- return -EBUSY; /* cannot unregister clockevent and clocksource */
-}
-
static const struct of_device_id em_sti_dt_ids[] = {
{ .compatible = "renesas,em-sti", },
{},
@@ -346,10 +341,10 @@ MODULE_DEVICE_TABLE(of, em_sti_dt_ids);
static struct platform_driver em_sti_device_driver = {
.probe = em_sti_probe,
- .remove = em_sti_remove,
.driver = {
.name = "em_sti",
.of_match_table = em_sti_dt_ids,
+ .suppress_bind_attrs = true,
}
};
@@ -1145,17 +1145,12 @@ static int sh_cmt_probe(struct platform_device *pdev)
return 0;
}
-static int sh_cmt_remove(struct platform_device *pdev)
-{
- return -EBUSY; /* cannot unregister clockevent and clocksource */
-}
-
static struct platform_driver sh_cmt_device_driver = {
.probe = sh_cmt_probe,
- .remove = sh_cmt_remove,
.driver = {
.name = "sh_cmt",
.of_match_table = of_match_ptr(sh_cmt_of_table),
+ .suppress_bind_attrs = true,
},
.id_table = sh_cmt_id_table,
};
@@ -632,11 +632,6 @@ static int sh_tmu_probe(struct platform_device *pdev)
return 0;
}
-static int sh_tmu_remove(struct platform_device *pdev)
-{
- return -EBUSY; /* cannot unregister clockevent and clocksource */
-}
-
static const struct platform_device_id sh_tmu_id_table[] = {
{ "sh-tmu", SH_TMU },
{ "sh-tmu-sh3", SH_TMU_SH3 },
@@ -652,10 +647,10 @@ MODULE_DEVICE_TABLE(of, sh_tmu_of_table);
static struct platform_driver sh_tmu_device_driver = {
.probe = sh_tmu_probe,
- .remove = sh_tmu_remove,
.driver = {
.name = "sh_tmu",
.of_match_table = of_match_ptr(sh_tmu_of_table),
+ .suppress_bind_attrs = true,
},
.id_table = sh_tmu_id_table,
};
@@ -9,6 +9,7 @@
#include <linux/clk.h>
#include <linux/clockchips.h>
+#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/of_address.h>
#include <linux/of_irq.h>
@@ -92,6 +93,8 @@ struct mchp_pit64b_clksrc {
static void __iomem *mchp_pit64b_cs_base;
/* Default cycles for clockevent timer. */
static u64 mchp_pit64b_ce_cycles;
+/* Delay timer. */
+static struct delay_timer mchp_pit64b_dt;
static inline u64 mchp_pit64b_cnt_read(void __iomem *base)
{
@@ -169,6 +172,11 @@ static u64 notrace mchp_pit64b_sched_read_clk(void)
return mchp_pit64b_cnt_read(mchp_pit64b_cs_base);
}
+static unsigned long notrace mchp_pit64b_dt_read(void)
+{
+ return mchp_pit64b_cnt_read(mchp_pit64b_cs_base);
+}
+
static int mchp_pit64b_clkevt_shutdown(struct clock_event_device *cedev)
{
struct mchp_pit64b_timer *timer = clkevt_to_mchp_pit64b_timer(cedev);
@@ -376,6 +384,10 @@ static int __init mchp_pit64b_init_clksrc(struct mchp_pit64b_timer *timer,
sched_clock_register(mchp_pit64b_sched_read_clk, 64, clk_rate);
+ mchp_pit64b_dt.read_current_timer = mchp_pit64b_dt_read;
+ mchp_pit64b_dt.freq = clk_rate;
+ register_current_timer_delay(&mchp_pit64b_dt);
+
return 0;
}
@@ -28,6 +28,7 @@
#include <asm/timex.h>
static DEFINE_STATIC_KEY_FALSE(riscv_sstc_available);
+static bool riscv_timer_cannot_wake_cpu;
static int riscv_clock_next_event(unsigned long delta,
struct clock_event_device *ce)
@@ -73,10 +74,15 @@ static u64 notrace riscv_sched_clock(void)
static struct clocksource riscv_clocksource = {
.name = "riscv_clocksource",
- .rating = 300,
+ .rating = 400,
.mask = CLOCKSOURCE_MASK(64),
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
.read = riscv_clocksource_rdtime,
+#if IS_ENABLED(CONFIG_GENERIC_GETTIMEOFDAY)
+ .vdso_clock_mode = VDSO_CLOCKMODE_ARCHTIMER,
+#else
+ .vdso_clock_mode = VDSO_CLOCKMODE_NONE,
+#endif
};
static int riscv_timer_starting_cpu(unsigned int cpu)
@@ -85,6 +91,8 @@ static int riscv_timer_starting_cpu(unsigned int cpu)
ce->cpumask = cpumask_of(cpu);
ce->irq = riscv_clock_event_irq;
+ if (riscv_timer_cannot_wake_cpu)
+ ce->features |= CLOCK_EVT_FEAT_C3STOP;
clockevents_config_and_register(ce, riscv_timebase, 100, 0x7fffffff);
enable_percpu_irq(riscv_clock_event_irq,
@@ -139,6 +147,13 @@ static int __init riscv_timer_init_dt(struct device_node *n)
if (cpuid != smp_processor_id())
return 0;
+ child = of_find_compatible_node(NULL, NULL, "riscv,timer");
+ if (child) {
+ riscv_timer_cannot_wake_cpu = of_property_read_bool(child,
+ "riscv,timer-cannot-wake-cpu");
+ of_node_put(child);
+ }
+
domain = NULL;
child = of_get_compatible_child(n, "riscv,cpu-intc");
if (!child) {
@@ -177,6 +192,11 @@ static int __init riscv_timer_init_dt(struct device_node *n)
return error;
}
+ if (riscv_isa_extension_available(NULL, SSTC)) {
+ pr_info("Timer interrupt in S-mode is available via sstc extension\n");
+ static_branch_enable(&riscv_sstc_available);
+ }
+
error = cpuhp_setup_state(CPUHP_AP_RISCV_TIMER_STARTING,
"clockevents/riscv/timer:starting",
riscv_timer_starting_cpu, riscv_timer_dying_cpu);
@@ -184,11 +204,6 @@ static int __init riscv_timer_init_dt(struct device_node *n)
pr_err("cpu hp setup state failed for RISCV timer [%d]\n",
error);
- if (riscv_isa_extension_available(NULL, SSTC)) {
- pr_info("Timer interrupt in S-mode is available via sstc extension\n");
- static_branch_enable(&riscv_sstc_available);
- }
-
return error;
}
@@ -144,7 +144,8 @@ static struct timer_of to = {
.clkevt = {
.name = "sun4i_tick",
.rating = 350,
- .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
+ .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT |
+ CLOCK_EVT_FEAT_DYNIRQ,
.set_state_shutdown = sun4i_clkevt_shutdown,
.set_state_periodic = sun4i_clkevt_set_periodic,
.set_state_oneshot = sun4i_clkevt_set_oneshot,
@@ -6,7 +6,6 @@
#include <vdso/bits.h>
#include <asm/bitsperlong.h>
-#define BIT_ULL(nr) (ULL(1) << (nr))
#define BIT_MASK(nr) (UL(1) << ((nr) % BITS_PER_LONG))
#define BIT_WORD(nr) ((nr) / BITS_PER_LONG)
#define BIT_ULL_MASK(nr) (ULL(1) << ((nr) % BITS_PER_LONG_LONG))
@@ -5,5 +5,6 @@
#include <vdso/const.h>
#define BIT(nr) (UL(1) << (nr))
+#define BIT_ULL(nr) (ULL(1) << (nr))
#endif /* __VDSO_BITS_H */
@@ -200,10 +200,14 @@ config CLOCKSOURCE_WATCHDOG_MAX_SKEW_US
int "Clocksource watchdog maximum allowable skew (in μs)"
depends on CLOCKSOURCE_WATCHDOG
range 50 1000
- default 100
+ default 125
help
Specify the maximum amount of allowable watchdog skew in
microseconds before reporting the clocksource to be unstable.
+ The default is based on a half-second clocksource watchdog
+ interval and NTP's maximum frequency drift of 500 parts
+ per million. If the clocksource is good enough for NTP,
+ it is good enough for the clocksource watchdog!
endmenu
endif
@@ -95,6 +95,11 @@ static char override_name[CS_NAME_LEN];
static int finished_booting;
static u64 suspend_start;
+/*
+ * Interval: 0.5sec.
+ */
+#define WATCHDOG_INTERVAL (HZ >> 1)
+
/*
* Threshold: 0.0312s, when doubled: 0.0625s.
* Also a default for cs->uncertainty_margin when registering clocks.
@@ -106,11 +111,14 @@ static u64 suspend_start;
* clocksource surrounding a read of the clocksource being validated.
* This delay could be due to SMIs, NMIs, or to VCPU preemptions. Used as
* a lower bound for cs->uncertainty_margin values when registering clocks.
+ *
+ * The default of 500 parts per million is based on NTP's limits.
+ * If a clocksource is good enough for NTP, it is good enough for us!
*/
#ifdef CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US
#define MAX_SKEW_USEC CONFIG_CLOCKSOURCE_WATCHDOG_MAX_SKEW_US
#else
-#define MAX_SKEW_USEC 100
+#define MAX_SKEW_USEC (125 * WATCHDOG_INTERVAL / HZ)
#endif
#define WATCHDOG_MAX_SKEW (MAX_SKEW_USEC * NSEC_PER_USEC)
@@ -140,11 +148,6 @@ static inline void clocksource_watchdog_unlock(unsigned long *flags)
static int clocksource_watchdog_kthread(void *data);
static void __clocksource_change_rating(struct clocksource *cs, int rating);
-/*
- * Interval: 0.5sec.
- */
-#define WATCHDOG_INTERVAL (HZ >> 1)
-
static void clocksource_watchdog_work(struct work_struct *work)
{
/*
@@ -257,8 +260,8 @@ static enum wd_read_status cs_watchdog_read(struct clocksource *cs, u64 *csnow,
goto skip_test;
}
- pr_warn("timekeeping watchdog on CPU%d: %s read-back delay of %lldns, attempt %d, marking unstable\n",
- smp_processor_id(), watchdog->name, wd_delay, nretries);
+ pr_warn("timekeeping watchdog on CPU%d: wd-%s-wd excessive read-back delay of %lldns vs. limit of %ldns, wd-wd read-back delay only %lldns, attempt %d, marking %s unstable\n",
+ smp_processor_id(), cs->name, wd_delay, WATCHDOG_MAX_SKEW, wd_seq_delay, nretries, cs->name);
return WD_READ_UNSTABLE;
skip_test:
@@ -384,6 +387,15 @@ void clocksource_verify_percpu(struct clocksource *cs)
}
EXPORT_SYMBOL_GPL(clocksource_verify_percpu);
+static inline void clocksource_reset_watchdog(void)
+{
+ struct clocksource *cs;
+
+ list_for_each_entry(cs, &watchdog_list, wd_list)
+ cs->flags &= ~CLOCK_SOURCE_WATCHDOG;
+}
+
+
static void clocksource_watchdog(struct timer_list *unused)
{
u64 csnow, wdnow, cslast, wdlast, delta;
@@ -391,6 +403,7 @@ static void clocksource_watchdog(struct timer_list *unused)
int64_t wd_nsec, cs_nsec;
struct clocksource *cs;
enum wd_read_status read_ret;
+ unsigned long extra_wait = 0;
u32 md;
spin_lock(&watchdog_lock);
@@ -410,13 +423,30 @@ static void clocksource_watchdog(struct timer_list *unused)
read_ret = cs_watchdog_read(cs, &csnow, &wdnow);
- if (read_ret != WD_READ_SUCCESS) {
- if (read_ret == WD_READ_UNSTABLE)
- /* Clock readout unreliable, so give it up. */
- __clocksource_unstable(cs);
+ if (read_ret == WD_READ_UNSTABLE) {
+ /* Clock readout unreliable, so give it up. */
+ __clocksource_unstable(cs);
continue;
}
+ /*
+ * When WD_READ_SKIP is returned, it means the system is likely
+ * under very heavy load, where the latency of reading
+ * watchdog/clocksource is very big, and affect the accuracy of
+ * watchdog check. So give system some space and suspend the
+ * watchdog check for 5 minutes.
+ */
+ if (read_ret == WD_READ_SKIP) {
+ /*
+ * As the watchdog timer will be suspended, and
+ * cs->last could keep unchanged for 5 minutes, reset
+ * the counters.
+ */
+ clocksource_reset_watchdog();
+ extra_wait = HZ * 300;
+ break;
+ }
+
/* Clocksource initialized ? */
if (!(cs->flags & CLOCK_SOURCE_WATCHDOG) ||
atomic_read(&watchdog_reset_pending)) {
@@ -443,12 +473,20 @@ static void clocksource_watchdog(struct timer_list *unused)
/* Check the deviation from the watchdog clocksource. */
md = cs->uncertainty_margin + watchdog->uncertainty_margin;
if (abs(cs_nsec - wd_nsec) > md) {
+ u64 cs_wd_msec;
+ u64 wd_msec;
+ u32 wd_rem;
+
pr_warn("timekeeping watchdog on CPU%d: Marking clocksource '%s' as unstable because the skew is too large:\n",
smp_processor_id(), cs->name);
pr_warn(" '%s' wd_nsec: %lld wd_now: %llx wd_last: %llx mask: %llx\n",
watchdog->name, wd_nsec, wdnow, wdlast, watchdog->mask);
pr_warn(" '%s' cs_nsec: %lld cs_now: %llx cs_last: %llx mask: %llx\n",
cs->name, cs_nsec, csnow, cslast, cs->mask);
+ cs_wd_msec = div_u64_rem(cs_nsec - wd_nsec, 1000U * 1000U, &wd_rem);
+ wd_msec = div_u64_rem(wd_nsec, 1000U * 1000U, &wd_rem);
+ pr_warn(" Clocksource '%s' skewed %lld ns (%lld ms) over watchdog '%s' interval of %lld ns (%lld ms)\n",
+ cs->name, cs_nsec - wd_nsec, cs_wd_msec, watchdog->name, wd_nsec, wd_msec);
if (curr_clocksource == cs)
pr_warn(" '%s' is current clocksource.\n", cs->name);
else if (curr_clocksource)
@@ -512,7 +550,7 @@ static void clocksource_watchdog(struct timer_list *unused)
* pair clocksource_stop_watchdog() clocksource_start_watchdog().
*/
if (!timer_pending(&watchdog_timer)) {
- watchdog_timer.expires += WATCHDOG_INTERVAL;
+ watchdog_timer.expires += WATCHDOG_INTERVAL + extra_wait;
add_timer_on(&watchdog_timer, next_cpu);
}
out:
@@ -537,14 +575,6 @@ static inline void clocksource_stop_watchdog(void)
watchdog_running = 0;
}
-static inline void clocksource_reset_watchdog(void)
-{
- struct clocksource *cs;
-
- list_for_each_entry(cs, &watchdog_list, wd_list)
- cs->flags &= ~CLOCK_SOURCE_WATCHDOG;
-}
-
static void clocksource_resume_watchdog(void)
{
atomic_inc(&watchdog_reset_pending);
@@ -2089,7 +2089,7 @@ long hrtimer_nanosleep(ktime_t rqtp, const enum hrtimer_mode mode,
u64 slack;
slack = current->timer_slack_ns;
- if (dl_task(current) || rt_task(current))
+ if (rt_task(current))
slack = 0;
hrtimer_init_sleeper_on_stack(&t, clockid, mode);
@@ -2126,6 +2126,7 @@ SYSCALL_DEFINE2(nanosleep, struct __kernel_timespec __user *, rqtp,
if (!timespec64_valid(&tu))
return -EINVAL;
+ current->restart_block.fn = do_no_restart_syscall;
current->restart_block.nanosleep.type = rmtp ? TT_NATIVE : TT_NONE;
current->restart_block.nanosleep.rmtp = rmtp;
return hrtimer_nanosleep(timespec64_to_ktime(tu), HRTIMER_MODE_REL,
@@ -2147,6 +2148,7 @@ SYSCALL_DEFINE2(nanosleep_time32, struct old_timespec32 __user *, rqtp,
if (!timespec64_valid(&tu))
return -EINVAL;
+ current->restart_block.fn = do_no_restart_syscall;
current->restart_block.nanosleep.type = rmtp ? TT_COMPAT : TT_NONE;
current->restart_block.nanosleep.compat_rmtp = rmtp;
return hrtimer_nanosleep(timespec64_to_ktime(tu), HRTIMER_MODE_REL,
@@ -2270,7 +2272,7 @@ void __init hrtimers_init(void)
/**
* schedule_hrtimeout_range_clock - sleep until timeout
* @expires: timeout value (ktime_t)
- * @delta: slack in expires timeout (ktime_t)
+ * @delta: slack in expires timeout (ktime_t) for SCHED_OTHER tasks
* @mode: timer mode
* @clock_id: timer clock to be used
*/
@@ -2297,6 +2299,13 @@ schedule_hrtimeout_range_clock(ktime_t *expires, u64 delta,
return -EINTR;
}
+ /*
+ * Override any slack passed by the user if under
+ * rt contraints.
+ */
+ if (rt_task(current))
+ delta = 0;
+
hrtimer_init_sleeper_on_stack(&t, clock_id, mode);
hrtimer_set_expires_range_ns(&t.timer, *expires, delta);
hrtimer_sleeper_start_expires(&t, mode);
@@ -2316,7 +2325,7 @@ EXPORT_SYMBOL_GPL(schedule_hrtimeout_range_clock);
/**
* schedule_hrtimeout_range - sleep until timeout
* @expires: timeout value (ktime_t)
- * @delta: slack in expires timeout (ktime_t)
+ * @delta: slack in expires timeout (ktime_t) for SCHED_OTHER tasks
* @mode: timer mode
*
* Make the current task sleep until the given expiry time has
@@ -2324,7 +2333,8 @@ EXPORT_SYMBOL_GPL(schedule_hrtimeout_range_clock);
* the current task state has been set (see set_current_state()).
*
* The @delta argument gives the kernel the freedom to schedule the
- * actual wakeup to a time that is both power and performance friendly.
+ * actual wakeup to a time that is both power and performance friendly
+ * for regular (non RT/DL) tasks.
* The kernel give the normal best effort behavior for "@expires+@delta",
* but may decide to fire the timer earlier, but no earlier than @expires.
*
@@ -243,13 +243,12 @@ static void proc_sample_cputime_atomic(struct task_cputime_atomic *at,
*/
static inline void __update_gt_cputime(atomic64_t *cputime, u64 sum_cputime)
{
- u64 curr_cputime;
-retry:
- curr_cputime = atomic64_read(cputime);
- if (sum_cputime > curr_cputime) {
- if (atomic64_cmpxchg(cputime, curr_cputime, sum_cputime) != curr_cputime)
- goto retry;
- }
+ u64 curr_cputime = atomic64_read(cputime);
+
+ do {
+ if (sum_cputime <= curr_cputime)
+ return;
+ } while (!atomic64_try_cmpxchg(cputime, &curr_cputime, sum_cputime));
}
static void update_gt_cputime(struct task_cputime_atomic *cputime_atomic,
@@ -147,6 +147,7 @@ SYSCALL_DEFINE4(clock_nanosleep, const clockid_t, which_clock, int, flags,
return -EINVAL;
if (flags & TIMER_ABSTIME)
rmtp = NULL;
+ current->restart_block.fn = do_no_restart_syscall;
current->restart_block.nanosleep.type = rmtp ? TT_NATIVE : TT_NONE;
current->restart_block.nanosleep.rmtp = rmtp;
texp = timespec64_to_ktime(t);
@@ -240,6 +241,7 @@ SYSCALL_DEFINE4(clock_nanosleep_time32, clockid_t, which_clock, int, flags,
return -EINVAL;
if (flags & TIMER_ABSTIME)
rmtp = NULL;
+ current->restart_block.fn = do_no_restart_syscall;
current->restart_block.nanosleep.type = rmtp ? TT_COMPAT : TT_NONE;
current->restart_block.nanosleep.compat_rmtp = rmtp;
texp = timespec64_to_ktime(t);
@@ -1270,6 +1270,7 @@ SYSCALL_DEFINE4(clock_nanosleep, const clockid_t, which_clock, int, flags,
return -EINVAL;
if (flags & TIMER_ABSTIME)
rmtp = NULL;
+ current->restart_block.fn = do_no_restart_syscall;
current->restart_block.nanosleep.type = rmtp ? TT_NATIVE : TT_NONE;
current->restart_block.nanosleep.rmtp = rmtp;
@@ -1297,6 +1298,7 @@ SYSCALL_DEFINE4(clock_nanosleep_time32, clockid_t, which_clock, int, flags,
return -EINVAL;
if (flags & TIMER_ABSTIME)
rmtp = NULL;
+ current->restart_block.fn = do_no_restart_syscall;
current->restart_block.nanosleep.type = rmtp ? TT_COMPAT : TT_NONE;
current->restart_block.nanosleep.compat_rmtp = rmtp;
@@ -149,7 +149,7 @@ module_init(udelay_test_init);
static void __exit udelay_test_exit(void)
{
mutex_lock(&udelay_test_lock);
- debugfs_remove(debugfs_lookup(DEBUGFS_FILENAME, NULL));
+ debugfs_lookup_and_remove(DEBUGFS_FILENAME, NULL);
mutex_unlock(&udelay_test_lock);
}