[v4] dt-bindings: usb: Add support for Microchip usb5744 hub controller
Commit Message
The Microchip usb5744 is a SS/HS USB 3.0 hub controller with 4 ports.
Add description for USB related aspects of the USB5744 hub, it as
well cover the option of connecting the controller as an i2c slave.
When i2c interface is connected hub needs to be initialized first.
Hub itself has fixed i2c address 0x2D but hardcoding address is not good
idea because address can be shifted by i2c address translator in the
middle.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
Changes in v4:
- Exchange allOf and required - requested by Krzysztof
Changes in v3:
- add maxItems to reg property
- remove select and define properties not used for i2c node and required
for usb
- s/binding/support/ in subject
- reword descripion to remove binding word from commit message
- wire usb-device.yaml for usb hub properties
Changes in v2:
- fix i2c-bus property
- swap usb2.0/3.0 compatible strings
- fix indentation in example (4 spaces)
- add new i2c node with microchip,usb5744 compatible property
It looks like that usb8041 has also an optional i2c interface which is not
covered. But it is mentioned at commit 40e58a8a7ca6 ("dt-bindings: usb:
Add binding for TI USB8041 hub controller").
i2c-bus name property was suggested by Rob at
https://lore.kernel.org/all/CAL_JsqJedhX6typpUKbnzV7CLK6UZVjq3CyG9iY_j5DLPqvVdw@mail.gmail.com/
and
https://lore.kernel.org/all/CAL_JsqJZBbu+UXqUNdZwg-uv0PAsNg55026PTwhKr5wQtxCjVQ@mail.gmail.com/
the question is if adding address like this is acceptable.
But it must be specified.
Driver will follow based on final dt-binding.
$ref: usb-device.yaml# should be also added but have no idea how to wire it
up to be applied only on usb node not i2c one.
---
.../bindings/usb/microchip,usb5744.yaml | 107 ++++++++++++++++++
1 file changed, 107 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/microchip,usb5744.yaml
new file mode 100644
@@ -0,0 +1,107 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/microchip,usb5744.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip USB5744 4-port Hub Controller
+
+description:
+ Microchip's USB5744 SmartHubTM IC is a 4 port, SuperSpeed (SS)/Hi-Speed (HS),
+ low power, low pin count configurable and fully compliant with the USB 3.1
+ Gen 1 specification. The USB5744 also supports Full Speed (FS) and Low Speed
+ (LS) USB signaling, offering complete coverage of all defined USB operating
+ speeds. The new SuperSpeed hubs operate in parallel with the USB 2.0
+ controller, so 5 Gbps SuperSpeed data transfers are not affected by slower
+ USB 2.0 traffic.
+
+maintainers:
+ - Piyush Mehta <piyush.mehta@amd.com>
+ - Michal Simek <michal.simek@amd.com>
+
+properties:
+ compatible:
+ enum:
+ - usb424,2744
+ - usb424,5744
+ - microchip,usb5744
+
+ reg:
+ maxItems: 1
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ GPIO controlling the GRST# pin.
+
+ vdd-supply:
+ description:
+ VDD power supply to the hub
+
+ peer-hub:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle to the peer hub on the controller.
+
+ i2c-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle of an usb hub connected via i2c bus.
+
+required:
+ - compatible
+ - reg
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: microchip,usb5744
+ then:
+ properties:
+ reset-gpios: false
+ vdd-supply: false
+ peer-hub: false
+ i2c-bus: false
+ else:
+ $ref: /schemas/usb/usb-device.yaml
+ required:
+ - peer-hub
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ i2c: i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ hub: usb-hub@2d {
+ compatible = "microchip,usb5744";
+ reg = <0x2d>;
+ };
+ };
+
+ usb {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* 2.0 hub on port 1 */
+ hub_2_0: hub@1 {
+ compatible = "usb424,2744";
+ reg = <1>;
+ peer-hub = <&hub_3_0>;
+ i2c-bus = <&hub>;
+ reset-gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ /* 3.0 hub on port 2 */
+ hub_3_0: hub@2 {
+ compatible = "usb424,5744";
+ reg = <2>;
+ peer-hub = <&hub_2_0>;
+ i2c-bus = <&hub>;
+ reset-gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ };
+ };