mbox series

[v3,0/8] Initial Marvell PXA1908 support

Message ID 20230804-pxa1908-lkml-v3-0-8e48fca37099@skole.hr
Headers
Series Initial Marvell PXA1908 support |

Message

Duje Mihanović Aug. 4, 2023, 1:32 p.m. UTC 
  v2 -> v3:
- Address maintainer comments:
  - Drop GPIO dynamic allocation patch
  - Move clock register offsets into driver (instead of bindings file)
  - Add missing Tested-by trailer to u32_fract patch
  - Move SoC binding to arm/mrvl/mrvl.yaml
- Add serial0 alias and stdout-path to board dts to enable UART
  debugging
- Rebase on v6.5-rc4

v1 -> v2:
- Remove earlycon patch as it's been merged into tty-next
- Address maintainer comments:
  - Clarify GPIO regressions on older PXA platforms
  - Add Fixes tag to commit disabling GPIO pinctrl calls for this SoC
  - Add missing includes to clock driver
  - Clock driver uses HZ_PER_MHZ, u32_fract and GENMASK
  - Dual license clock bindings
  - Change clock IDs to decimal
  - Fix underscores in dt node names
  - Move chosen node to top of board dts
  - Clean up documentation
  - Reorder commits
  - Drop pxa,rev-id
- Rename muic-i2c to i2c-muic
- Reword some commits
- Move framebuffer node to chosen
- Add aliases for mmc nodes
- Rebase on v6.5-rc3

Hello,

This series adds initial support for the Marvell PXA1908 SoC and
"samsung,coreprimevelte", a smartphone using the SoC.

USB works and the phone can boot a rootfs from an SD card, but there are
some warnings in the dmesg:

During SMP initialization:
[    0.006519] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU1: 0x00000000000000
[    0.006542] CPU features: Unsupported CPU feature variation detected.
[    0.006589] CPU1: Booted secondary processor 0x0000000001 [0x410fd032]
[    0.010710] Detected VIPT I-cache on CPU2
[    0.010716] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU2: 0x00000000000000
[    0.010758] CPU2: Booted secondary processor 0x0000000002 [0x410fd032]
[    0.014849] Detected VIPT I-cache on CPU3
[    0.014855] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x000000018cba80, CPU3: 0x00000000000000
[    0.014895] CPU3: Booted secondary processor 0x0000000003 [0x410fd032]

SMMU probing fails:
[    0.101798] arm-smmu c0010000.iommu: probing hardware configuration...
[    0.101809] arm-smmu c0010000.iommu: SMMUv1 with:
[    0.101816] arm-smmu c0010000.iommu:         no translation support!

On Samsung's PXA1908 phones, the bootloader does not start the ARM
system timer, and my temporary solution (which isn't present in this
series) was to put the code for starting the timer in the clock driver.
Would this hack be accepted upstream in the form of a platform or
clocksource driver such as drivers/clocksource/timer-mediatek-cpux.c?

A 3.14 based Marvell tree is available on GitHub
acorn-marvell/brillo_pxa_kernel, and a Samsung one on GitHub
CoderCharmander/g361f-kernel.

Andreas Färber attempted to upstream support for this SoC in 2017:
https://lore.kernel.org/lkml/20170222022929.10540-1-afaerber@suse.de/

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
Andy Shevchenko (1):
      clk: mmp: Switch to use struct u32_fract instead of custom one

Duje Mihanović (7):
      gpio: pxa: disable pinctrl calls for MMP_GPIO
      dt-bindings: clock: Add Marvell PXA1908 clock bindings
      clk: mmp: Add Marvell PXA1908 clock driver
      dt-bindings: marvell: Document PXA1908 SoC
      arm64: Kconfig.platforms: Add config for Marvell PXA1908 platform
      arm64: dts: Add DTS for Marvell PXA1908 and samsung,coreprimevelte
      MAINTAINERS: add myself as Marvell PXA1908 maintainer

 .../devicetree/bindings/arm/mrvl/mrvl.yaml         |   5 +
 .../devicetree/bindings/clock/marvell,pxa1908.yaml |  48 +++
 MAINTAINERS                                        |   9 +
 arch/arm64/Kconfig.platforms                       |  11 +
 arch/arm64/boot/dts/marvell/Makefile               |   3 +
 .../dts/marvell/pxa1908-samsung-coreprimevelte.dts | 332 +++++++++++++++++++++
 arch/arm64/boot/dts/marvell/pxa1908.dtsi           | 292 ++++++++++++++++++
 drivers/clk/mmp/Makefile                           |   2 +-
 drivers/clk/mmp/clk-frac.c                         |  57 ++--
 drivers/clk/mmp/clk-mmp2.c                         |   6 +-
 drivers/clk/mmp/clk-of-mmp2.c                      |  26 +-
 drivers/clk/mmp/clk-of-pxa168.c                    |   4 +-
 drivers/clk/mmp/clk-of-pxa1908.c                   | 323 ++++++++++++++++++++
 drivers/clk/mmp/clk-of-pxa1928.c                   |   6 +-
 drivers/clk/mmp/clk-of-pxa910.c                    |   4 +-
 drivers/clk/mmp/clk-pxa168.c                       |   4 +-
 drivers/clk/mmp/clk-pxa910.c                       |   4 +-
 drivers/clk/mmp/clk.h                              |  10 +-
 drivers/gpio/gpio-pxa.c                            |   1 +
 include/dt-bindings/clock/marvell,pxa1908.h        |  92 ++++++
 20 files changed, 1175 insertions(+), 64 deletions(-)
---
base-commit: 5d0c230f1de8c7515b6567d9afba1f196fb4e2f4
change-id: 20230803-pxa1908-lkml-6830e8da45c7

Best regards,