[v7,0/7] Add PLL clocks driver and syscon for StarFive JH7110 SoC

  This patch serises are to add PLL clocks driver and providers by writing
and reading syscon registers for the StarFive JH7110 RISC-V SoC. And add 
documentation and nodes to describe StarFive System Controller(syscon)
Registers. This patch serises are based on Linux 6.4.

PLLs are high speed, low jitter frequency synthesizers in JH7110.
Each PLL clock works in integer mode or fraction mode by some dividers,
and the dividers are set in several syscon registers.
The formula for calculating frequency is: 
Fvco = Fref * (NI + NF) / M / Q1

The first patch adds docunmentation to describe PLL clock bindings,
and the second patch adds documentation to decribe syscon registers.
The patch 3 modifies the SYSCRG bindings and adds PLL clock inputs.
The patch 4 adds driver to support PLL clocks for JH7110.
The patch 5 modifies the system clock driver and can select the PLL clock
source from PLL clocks driver. And the patch 6 adds the 
stg/sys/aon syscon nodes for JH7110 SoC. The last patch modifies the 
syscrg node in JH7110 dts file.

Changes since v6:
- Rebased on Linux 6.5-rc2.
- Patch 1 added the 'the' in front of 'JH7110' and changed the PLL clock
  names from 'JH7110_CLK_PLL?_OUT' to 'JH7110_PLLCLK_PLL?_OUT' in the
  binding of PLL.
- Patch 2 modified the value of 'reg' in example to fix the error.
- Patch 4 and 7 changed the PLL clock names from 'JH7110_CLK_PLL?_OUT'
  to 'JH7110_PLLCLK_PLL?_OUT' in the driver and dts.
- Patch 5 added clk_put() and a better way to detect if the pll
  references are specified in the device tree or not.

v6: https://lore.kernel.org/all/20230704064610.292603-1-xingyu.wu@starfivetech.com/

Changes since v5: 
- Rebased on Linux 6.4.
- Patch 1 fixed some grammatical mistake.
- Patch 2 added the selection about properties from different syscon
  modules and madethe example completed.
- Patch 3 dropped the 'optional' PLL clocks.

v5: https://lore.kernel.org/all/20230613125852.211636-1-xingyu.wu@starfivetech.com/

Changes since v4: 
- Rebased on Linux 6.4-rc6.
- Patch 2 dropped the example node about sys-syscon.
- Patch 3 used PLL clocks as one of optional items in SYSCRG bindings.
- Patch 4 used the patch instead about PLL clocks driver from Emil.
- Patch 5 retained the fixed factor PLL clocks as the optional source
  about PLL clocks in SYSCRG clock driver.
- Patch 6 added the child node clock-controller as the complete
  sys-syscon node and patch 7 dropped this part.

v4: https://lore.kernel.org/all/20230512022036.97987-1-xingyu.wu@starfivetech.com/

Changes since v3: 
- Rebased on Linux 6.4-rc1.
- Dropped the 'power-controller' property and used 'power-domain-cells'
  instead in syscon binding.
- Used the data by of_device_id to get the syscon registers'
  configuration include offset, mask and shift.

v3: https://lore.kernel.org/all/20230414024157.53203-1-xingyu.wu@starfivetech.com/

Changes since v2: 
- Rebased on latest JH7110 basic clock drivers.
- Added the complete documentation to describe syscon register.
- Added syscon node in JH7110 dts file.
- Modified the clock rate selection to match the closest rate in
  PLL driver when setting rate.

v2: https://lore.kernel.org/all/20230316030514.137427-1-xingyu.wu@starfivetech.com/

Changes since v1:
- Changed PLL clock node to be child of syscon node in dts.
- Modifed the definitions and names of function in PLL clock driver.
- Added commit to update syscon and syscrg dt-bindings.

v1: https://lore.kernel.org/all/20230221141147.303642-1-xingyu.wu@starfivetech.com/

William Qiu (2):
  dt-bindings: soc: starfive: Add StarFive syscon module
  riscv: dts: starfive: jh7110: Add syscon nodes

Xingyu Wu (5):
  dt-bindings: clock: Add StarFive JH7110 PLL clock generator
  dt-bindings: clock: jh7110-syscrg: Add PLL clock inputs
  clk: starfive: Add StarFive JH7110 PLL clock driver
  clk: starfive: jh7110-sys: Add PLL clocks source from DTS
  riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node

 .../bindings/clock/starfive,jh7110-pll.yaml   |  46 ++
 .../clock/starfive,jh7110-syscrg.yaml         |  18 +-
 .../soc/starfive/starfive,jh7110-syscon.yaml  |  93 ++++
 MAINTAINERS                                   |  13 +
 arch/riscv/boot/dts/starfive/jh7110.dtsi      |  30 +-
 drivers/clk/starfive/Kconfig                  |   9 +
 drivers/clk/starfive/Makefile                 |   1 +
 .../clk/starfive/clk-starfive-jh7110-pll.c    | 507 ++++++++++++++++++
 .../clk/starfive/clk-starfive-jh7110-sys.c    |  66 ++-
 .../dt-bindings/clock/starfive,jh7110-crg.h   |   6 +
 10 files changed, 763 insertions(+), 26 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/starfive,jh7110-pll.yaml
 create mode 100644 Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
 create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-pll.c
  

Hey Xingyu,

On Mon, Jul 17, 2023 at 10:30:33AM +0800, Xingyu Wu wrote:
> This patch serises are to add PLL clocks driver and providers by writing
> and reading syscon registers for the StarFive JH7110 RISC-V SoC. And add 
> documentation and nodes to describe StarFive System Controller(syscon)
> Registers. This patch serises are based on Linux 6.4.
> 
> PLLs are high speed, low jitter frequency synthesizers in JH7110.
> Each PLL clock works in integer mode or fraction mode by some dividers,
> and the dividers are set in several syscon registers.
> The formula for calculating frequency is: 
> Fvco = Fref * (NI + NF) / M / Q1
> 
> The first patch adds docunmentation to describe PLL clock bindings,
> and the second patch adds documentation to decribe syscon registers.
> The patch 3 modifies the SYSCRG bindings and adds PLL clock inputs.
> The patch 4 adds driver to support PLL clocks for JH7110.
> The patch 5 modifies the system clock driver and can select the PLL clock
> source from PLL clocks driver. And the patch 6 adds the 
> stg/sys/aon syscon nodes for JH7110 SoC. The last patch modifies the 
> syscrg node in JH7110 dts file.

Just FYI, I have picked up the binding & clock portions of this series
and your other one adding the stg syscon. I've pushed them out here for
the test robots to have a look:
https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/log/?h=clk-starfive

If that passes, my plan is to send Stephen a PR for the lot, later this
week.

Thanks,
Conor.
  

On 2023/7/18 2:14, Conor Dooley wrote:
> Hey Xingyu,
> 
> On Mon, Jul 17, 2023 at 10:30:33AM +0800, Xingyu Wu wrote:
>> This patch serises are to add PLL clocks driver and providers by writing
>> and reading syscon registers for the StarFive JH7110 RISC-V SoC. And add 
>> documentation and nodes to describe StarFive System Controller(syscon)
>> Registers. This patch serises are based on Linux 6.4.
>> 
>> PLLs are high speed, low jitter frequency synthesizers in JH7110.
>> Each PLL clock works in integer mode or fraction mode by some dividers,
>> and the dividers are set in several syscon registers.
>> The formula for calculating frequency is: 
>> Fvco = Fref * (NI + NF) / M / Q1
>> 
>> The first patch adds docunmentation to describe PLL clock bindings,
>> and the second patch adds documentation to decribe syscon registers.
>> The patch 3 modifies the SYSCRG bindings and adds PLL clock inputs.
>> The patch 4 adds driver to support PLL clocks for JH7110.
>> The patch 5 modifies the system clock driver and can select the PLL clock
>> source from PLL clocks driver. And the patch 6 adds the 
>> stg/sys/aon syscon nodes for JH7110 SoC. The last patch modifies the 
>> syscrg node in JH7110 dts file.
> 
> Just FYI, I have picked up the binding & clock portions of this series
> and your other one adding the stg syscon. I've pushed them out here for
> the test robots to have a look:
> https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/log/?h=clk-starfive
> 
> If that passes, my plan is to send Stephen a PR for the lot, later this
> week.
> 

Great. Thank you for everything.

Best regards,
Xingyu Wu
  

From: Conor Dooley <conor.dooley@microchip.com>

On Mon, 17 Jul 2023 10:30:33 +0800, Xingyu Wu wrote:
> This patch serises are to add PLL clocks driver and providers by writing
> and reading syscon registers for the StarFive JH7110 RISC-V SoC. And add
> documentation and nodes to describe StarFive System Controller(syscon)
> Registers. This patch serises are based on Linux 6.4.
> 
> PLLs are high speed, low jitter frequency synthesizers in JH7110.
> Each PLL clock works in integer mode or fraction mode by some dividers,
> and the dividers are set in several syscon registers.
> The formula for calculating frequency is:
> Fvco = Fref * (NI + NF) / M / Q1
> 
> [...]

Applied to riscv-dt-for-next, thanks!

[6/7] riscv: dts: starfive: jh7110: Add syscon nodes
      https://git.kernel.org/conor/c/3fcbcfc496f0
[7/7] riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
      https://git.kernel.org/conor/c/3e6670a28b00

Thanks,
Conor.