mbox series

[0/4] Enable multiple MCAN on AM62x

Message ID 20230419223323.20384-1-jm@ti.com
Headers
Series Enable multiple MCAN on AM62x |

Message

Judith Mendez April 19, 2023, 10:33 p.m. UTC 
  On AM62x there is one MCAN in MAIN domain and two in MCU domain.
The MCANs in MCU domain were not enabled since there is no
hardware interrupt routed to A53 GIC interrupt controller.
Therefore A53 Linux cannot be interrupted by MCU MCANs.

This solution instantiates a hrtimer with 1 ms polling interval
for a MCAN when there is no hardware interrupt. This hrtimer
generates a recurring software interrupt which allows to call the
isr. The isr will check if there is pending transaction by reading
a register and proceed normally if there is.

On AM62x this series enables two MCU MCAN which will use the hrtimer
implementation. MCANs with hardware interrupt routed to A53 Linux
will continue to use the hardware interrupt as expected.

Timer polling method was tested on both classic CAN and CAN-FD
at 125 KBPS, 250 KBPS, 1 MBPS and 2.5 MBPS with 4 MBPS bitrate
switching.

Letency and CPU load benchmarks were tested on 3x MCAN on AM62x.
1 MBPS timer polling interval is the better timer polling interval
since it has comparable latency to hardware interrupt with the worse
case being 1ms + CAN frame propagation time and CPU load is not
substantial. Latency can be improved further with less than 1 ms
polling intervals, howerver it is at the cost of CPU usage since CPU
load increases at 0.5 ms and lower polling periods than 1ms.

Note that in terms of power, enabling MCU MCANs with timer-polling
implementation might have negative impact since we will have to wake
up every 1 ms whether there are CAN packets pending in the RX FIFO or
not. This might prevent the CPU from entering into deeper idle states
for extended periods of time.

This patch series depends on 'Enable CAN PHY transceiver driver':
https://lore.kernel.org/lkml/775ec9ce-7668-429c-a977-6c8995968d6e@app.fastmail.com/T/

Previously sent an RFC:
https://lore.kernel.org/linux-can/52a37e51-4143-9017-42ee-8d17c67028e3@ti.com/T/#t

Judith Mendez (4):
  can: m_can: Add hrtimer to generate software interrupt
  dt-bindings: net: can: Make interrupt attributes optional for MCAN
  arm64: dts: ti: Add AM62x MCAN MAIN domain transceiver overlay
  arm64: dts: ti: Enable MCU MCANs for AM62x

 .../bindings/net/can/bosch,m_can.yaml         |  2 -
 arch/arm64/boot/dts/ti/Makefile               |  2 +
 arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi       | 24 ++++++++
 .../boot/dts/ti/k3-am625-sk-mcan-main.dtso    | 35 ++++++++++++
 .../boot/dts/ti/k3-am625-sk-mcan-mcu.dtso     | 55 +++++++++++++++++++
 drivers/net/can/m_can/m_can.c                 | 30 +++++++++-
 drivers/net/can/m_can/m_can.h                 |  3 +
 drivers/net/can/m_can/m_can_platform.c        | 13 ++++-
 8 files changed, 158 insertions(+), 6 deletions(-)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am625-sk-mcan-main.dtso
 create mode 100644 arch/arm64/boot/dts/ti/k3-am625-sk-mcan-mcu.dtso