[v3,0/9] mips: ralink: add complete clock and reset driver for mtmips SoCs

  Hi all!

This patchset is a big effort to properly implement a clock and reset
driver for old ralink SoCs. This allow to properly define clocks in 
device tree and avoid to use fixed-clocks directly from 'arch/mips/ralink'
architecture directory code.

Device tree 'sysc' node will be both clock and reset provider using 
'clock-cells' and 'reset-cells' properties.

The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350,
RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in
this new driver has been extracted from 'arch/mips/ralink' and cleanly
put using kernel clock and reset driver APIs. The clock plans for this
SoCs only talks about relation between CPU frequency and BUS frequency.
This relation is different depending on the particular SoC. CPU clock is
derived from XTAL frequencies.

 Depending on the SoC we have the following frequencies:
 * RT2880 SoC:
     - XTAL: 40 MHz.
     - CPU: 250, 266, 280 or 300 MHz.
     - BUS: CPU / 2 MHz.
  * RT3050, RT3052, RT3350:
     - XTAL: 40 MHz.
     - CPU: 320 or 384 MHz.
     - BUS: CPU / 3 MHz.
  * RT3352:
     - XTAL: 40 MHz.
     - CPU: 384 or 400 MHz.
     - BUS: CPU / 3 MHz.
     - PERIPH: 40 MHz.
  * RT3383:
     - XTAL: 40 MHz.
     - CPU: 250, 384, 480 or 500 MHz.
     - BUS: Depends on RAM Type and CPU:
       + RAM DDR2: 125. ELSE 83 MHz.
       + RAM DDR2: 128. ELSE 96 MHz.
       + RAM DDR2: 160. ELSE 120 MHz.
       + RAM DDR2: 166. ELSE 125 MHz.
  * RT5350:
      - XTAL: 40 MHz.
      - CPU: 300, 320 or 360 MHz.
      - BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
      - PERIPH: 40 MHz.
  * MT7628 and MT7688:
     - XTAL: 20 MHz or 40 MHz.
     - CPU: 575 or 580 MHz.
     - BUS: CPU / 3.
     - PCMI2S: 480 MHz.
     - PERIPH: 40 MHz.
  * MT7620:
     - XTAL: 20 MHz or 40 MHz.
     - PLL: XTAL, 480, 600 MHz.
     - CPU: depends on PLL and some mult and dividers.
     - BUS: depends on PLL and some mult and dividers.
     - PERIPH: 40 or XTAL MHz.

MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of
register reads and predividers. To derive CPU and BUS frequencies in the
MT7620 SoC 'mt7620_calc_rate()' helper is used.
In the case XTAL can have different frequencies and we need a different
clock frequency for peripherals 'periph' clock in introduced.
The rest of the peripherals present in the SoC just follow their parent
frequencies.

I am using 'mtmips' inside for ralink clock driver. This is aligned with
pinctrl series recently merged through pinctrl git tree [0].

I am maintaining ralink as prefix for compatible strings after discussions
between Rob and Arinc in v2 of this series [1].

Changes have been compile tested for:
- RT2880
- RT3883
- MT7620

Changes have been properly tested in RT5350 SoC based board (ALL5003 board)
resulting in a working platform.

Dts files for these SoCs in-tree except MT7621 are incomplete. We are
planning to align with openWRT files at some point and add extra needed
changes. Hence I am not touching them at all in these series. If this is
a problem, please let me know and I will update them.

Talking about merging this series I'd like all of the patches going through
the MIPS tree if possible.

Thanks in advance for your time.

Best regards,
    Sergio Paracuellos

Changes in v3:
- Address Stephen comments in v2:
    + Drop unsused include '<linux/clk.h>'.
    + Add fixed and factor clocks when it makes sense.
    + Make 'mtmips_periph_clk_ops' named variable.
    + WARN_ON -> WARN_ON_ONCE.
    + Avoid CONFIG_USB dependent code. Introduce new 'mtmips_clk_regs_init'.
    + Don't validate the bindings in the driver.
    + Make const 'struct clk_init_data' used inside macros.
    + do_div -> div_u64.
    + Make use of dev_err_probe.

Changes in v2:
- Address bindings documentation changes pointed out by Krzysztof:
    + Rename the file into 'mediatek,mtmips-sysc.yaml'.
    + Redo commit subject and log message.
    + Order compatibles alphabetically.
    + Redo bindings description taking into account this is a system
      controller node which provides both clocks and resets to the world.
    + Drop label from example.
    + Use 'syscon' as node name in example.
    + Drop no sense 'ralink,rt2880-reset' compatible string 
- Squash patches 6 and 7 together as pointed out by Stephen Boyd.

Previoous series:
v2: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#t
v1: https://lore.kernel.org/linux-clk/20230320161823.1424278-1-sergio.paracuellos@gmail.com/T/#t

[0]: https://lore.kernel.org/linux-gpio/e9e6ad87-2db5-9767-ff39-64a302b06185@arinc9.com/T/#t
[1]: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#mfe725b6e3382c6fb09736472a846cbbc84f264dc

Sergio Paracuellos (9):
  dt-bindings: clock: add mtmips SoCs system controller
  clk: ralink: add clock and reset driver for MTMIPS SoCs
  mips: ralink: rt288x: remove clock related code
  mips: ralink: rt305x: remove clock related code
  mips: ralink: rt3883: remove clock related code
  mips: ralink: mt7620: remove clock related code
  mips: ralink: remove reset related code
  mips: ralink: get cpu rate from new driver code
  MAINTAINERS: add Mediatek MTMIPS Clock maintainer

 .../bindings/clock/mediatek,mtmips-sysc.yaml  |   65 +
 MAINTAINERS                                   |    6 +
 arch/mips/include/asm/mach-ralink/mt7620.h    |   35 -
 arch/mips/include/asm/mach-ralink/rt288x.h    |   10 -
 arch/mips/include/asm/mach-ralink/rt305x.h    |   21 -
 arch/mips/include/asm/mach-ralink/rt3883.h    |    8 -
 arch/mips/ralink/clk.c                        |   26 +-
 arch/mips/ralink/common.h                     |    5 -
 arch/mips/ralink/mt7620.c                     |  226 ----
 arch/mips/ralink/of.c                         |    4 -
 arch/mips/ralink/reset.c                      |   61 -
 arch/mips/ralink/rt288x.c                     |   31 -
 arch/mips/ralink/rt305x.c                     |   78 --
 arch/mips/ralink/rt3883.c                     |   44 -
 drivers/clk/ralink/Kconfig                    |    7 +
 drivers/clk/ralink/Makefile                   |    1 +
 drivers/clk/ralink/clk-mtmips.c               | 1134 +++++++++++++++++
 17 files changed, 1232 insertions(+), 530 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml
 create mode 100644 drivers/clk/ralink/clk-mtmips.c
  

On Tue, Apr 18, 2023 at 11:03 AM Sergio Paracuellos
<sergio.paracuellos@gmail.com> wrote:
>
> Hi all!
>
> This patchset is a big effort to properly implement a clock and reset
> driver for old ralink SoCs. This allow to properly define clocks in
> device tree and avoid to use fixed-clocks directly from 'arch/mips/ralink'
> architecture directory code.
>
> Device tree 'sysc' node will be both clock and reset provider using
> 'clock-cells' and 'reset-cells' properties.
>
> The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350,
> RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in
> this new driver has been extracted from 'arch/mips/ralink' and cleanly
> put using kernel clock and reset driver APIs. The clock plans for this
> SoCs only talks about relation between CPU frequency and BUS frequency.
> This relation is different depending on the particular SoC. CPU clock is
> derived from XTAL frequencies.
>
>  Depending on the SoC we have the following frequencies:
>  * RT2880 SoC:
>      - XTAL: 40 MHz.
>      - CPU: 250, 266, 280 or 300 MHz.
>      - BUS: CPU / 2 MHz.
>   * RT3050, RT3052, RT3350:
>      - XTAL: 40 MHz.
>      - CPU: 320 or 384 MHz.
>      - BUS: CPU / 3 MHz.
>   * RT3352:
>      - XTAL: 40 MHz.
>      - CPU: 384 or 400 MHz.
>      - BUS: CPU / 3 MHz.
>      - PERIPH: 40 MHz.
>   * RT3383:
>      - XTAL: 40 MHz.
>      - CPU: 250, 384, 480 or 500 MHz.
>      - BUS: Depends on RAM Type and CPU:
>        + RAM DDR2: 125. ELSE 83 MHz.
>        + RAM DDR2: 128. ELSE 96 MHz.
>        + RAM DDR2: 160. ELSE 120 MHz.
>        + RAM DDR2: 166. ELSE 125 MHz.
>   * RT5350:
>       - XTAL: 40 MHz.
>       - CPU: 300, 320 or 360 MHz.
>       - BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
>       - PERIPH: 40 MHz.
>   * MT7628 and MT7688:
>      - XTAL: 20 MHz or 40 MHz.
>      - CPU: 575 or 580 MHz.
>      - BUS: CPU / 3.
>      - PCMI2S: 480 MHz.
>      - PERIPH: 40 MHz.
>   * MT7620:
>      - XTAL: 20 MHz or 40 MHz.
>      - PLL: XTAL, 480, 600 MHz.
>      - CPU: depends on PLL and some mult and dividers.
>      - BUS: depends on PLL and some mult and dividers.
>      - PERIPH: 40 or XTAL MHz.
>
> MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of
> register reads and predividers. To derive CPU and BUS frequencies in the
> MT7620 SoC 'mt7620_calc_rate()' helper is used.
> In the case XTAL can have different frequencies and we need a different
> clock frequency for peripherals 'periph' clock in introduced.
> The rest of the peripherals present in the SoC just follow their parent
> frequencies.
>
> I am using 'mtmips' inside for ralink clock driver. This is aligned with
> pinctrl series recently merged through pinctrl git tree [0].
>
> I am maintaining ralink as prefix for compatible strings after discussions
> between Rob and Arinc in v2 of this series [1].
>
> Changes have been compile tested for:
> - RT2880
> - RT3883
> - MT7620
>
> Changes have been properly tested in RT5350 SoC based board (ALL5003 board)
> resulting in a working platform.
>
> Dts files for these SoCs in-tree except MT7621 are incomplete. We are
> planning to align with openWRT files at some point and add extra needed
> changes. Hence I am not touching them at all in these series. If this is
> a problem, please let me know and I will update them.
>
> Talking about merging this series I'd like all of the patches going through
> the MIPS tree if possible.
>
> Thanks in advance for your time.
>
> Best regards,
>     Sergio Paracuellos
>
> Changes in v3:
> - Address Stephen comments in v2:
>     + Drop unsused include '<linux/clk.h>'.
>     + Add fixed and factor clocks when it makes sense.
>     + Make 'mtmips_periph_clk_ops' named variable.
>     + WARN_ON -> WARN_ON_ONCE.
>     + Avoid CONFIG_USB dependent code. Introduce new 'mtmips_clk_regs_init'.
>     + Don't validate the bindings in the driver.
>     + Make const 'struct clk_init_data' used inside macros.
>     + do_div -> div_u64.
>     + Make use of dev_err_probe.

Hi Stephen,

Does anything else need to be addressed to have all of these added?

Philipp, can you please review the reset related code in PATCH 2/9 of
these series?

Thanks in advance for your time!

Best regards,
    Sergio Paracuellos

>
> Changes in v2:
> - Address bindings documentation changes pointed out by Krzysztof:
>     + Rename the file into 'mediatek,mtmips-sysc.yaml'.
>     + Redo commit subject and log message.
>     + Order compatibles alphabetically.
>     + Redo bindings description taking into account this is a system
>       controller node which provides both clocks and resets to the world.
>     + Drop label from example.
>     + Use 'syscon' as node name in example.
>     + Drop no sense 'ralink,rt2880-reset' compatible string
> - Squash patches 6 and 7 together as pointed out by Stephen Boyd.
>
> Previoous series:
> v2: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#t
> v1: https://lore.kernel.org/linux-clk/20230320161823.1424278-1-sergio.paracuellos@gmail.com/T/#t
>
> [0]: https://lore.kernel.org/linux-gpio/e9e6ad87-2db5-9767-ff39-64a302b06185@arinc9.com/T/#t
> [1]: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#mfe725b6e3382c6fb09736472a846cbbc84f264dc
>
> Sergio Paracuellos (9):
>   dt-bindings: clock: add mtmips SoCs system controller
>   clk: ralink: add clock and reset driver for MTMIPS SoCs
>   mips: ralink: rt288x: remove clock related code
>   mips: ralink: rt305x: remove clock related code
>   mips: ralink: rt3883: remove clock related code
>   mips: ralink: mt7620: remove clock related code
>   mips: ralink: remove reset related code
>   mips: ralink: get cpu rate from new driver code
>   MAINTAINERS: add Mediatek MTMIPS Clock maintainer
>
>  .../bindings/clock/mediatek,mtmips-sysc.yaml  |   65 +
>  MAINTAINERS                                   |    6 +
>  arch/mips/include/asm/mach-ralink/mt7620.h    |   35 -
>  arch/mips/include/asm/mach-ralink/rt288x.h    |   10 -
>  arch/mips/include/asm/mach-ralink/rt305x.h    |   21 -
>  arch/mips/include/asm/mach-ralink/rt3883.h    |    8 -
>  arch/mips/ralink/clk.c                        |   26 +-
>  arch/mips/ralink/common.h                     |    5 -
>  arch/mips/ralink/mt7620.c                     |  226 ----
>  arch/mips/ralink/of.c                         |    4 -
>  arch/mips/ralink/reset.c                      |   61 -
>  arch/mips/ralink/rt288x.c                     |   31 -
>  arch/mips/ralink/rt305x.c                     |   78 --
>  arch/mips/ralink/rt3883.c                     |   44 -
>  drivers/clk/ralink/Kconfig                    |    7 +
>  drivers/clk/ralink/Makefile                   |    1 +
>  drivers/clk/ralink/clk-mtmips.c               | 1134 +++++++++++++++++
>  17 files changed, 1232 insertions(+), 530 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml
>  create mode 100644 drivers/clk/ralink/clk-mtmips.c
>
> --
> 2.25.1
>
  

On Thu, May 4, 2023 at 4:48 PM Sergio Paracuellos
<sergio.paracuellos@gmail.com> wrote:
>
> On Tue, Apr 18, 2023 at 11:03 AM Sergio Paracuellos
> <sergio.paracuellos@gmail.com> wrote:
> >
> > Hi all!
> >
> > This patchset is a big effort to properly implement a clock and reset
> > driver for old ralink SoCs. This allow to properly define clocks in
> > device tree and avoid to use fixed-clocks directly from 'arch/mips/ralink'
> > architecture directory code.
> >
> > Device tree 'sysc' node will be both clock and reset provider using
> > 'clock-cells' and 'reset-cells' properties.
> >
> > The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350,
> > RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in
> > this new driver has been extracted from 'arch/mips/ralink' and cleanly
> > put using kernel clock and reset driver APIs. The clock plans for this
> > SoCs only talks about relation between CPU frequency and BUS frequency.
> > This relation is different depending on the particular SoC. CPU clock is
> > derived from XTAL frequencies.
> >
> >  Depending on the SoC we have the following frequencies:
> >  * RT2880 SoC:
> >      - XTAL: 40 MHz.
> >      - CPU: 250, 266, 280 or 300 MHz.
> >      - BUS: CPU / 2 MHz.
> >   * RT3050, RT3052, RT3350:
> >      - XTAL: 40 MHz.
> >      - CPU: 320 or 384 MHz.
> >      - BUS: CPU / 3 MHz.
> >   * RT3352:
> >      - XTAL: 40 MHz.
> >      - CPU: 384 or 400 MHz.
> >      - BUS: CPU / 3 MHz.
> >      - PERIPH: 40 MHz.
> >   * RT3383:
> >      - XTAL: 40 MHz.
> >      - CPU: 250, 384, 480 or 500 MHz.
> >      - BUS: Depends on RAM Type and CPU:
> >        + RAM DDR2: 125. ELSE 83 MHz.
> >        + RAM DDR2: 128. ELSE 96 MHz.
> >        + RAM DDR2: 160. ELSE 120 MHz.
> >        + RAM DDR2: 166. ELSE 125 MHz.
> >   * RT5350:
> >       - XTAL: 40 MHz.
> >       - CPU: 300, 320 or 360 MHz.
> >       - BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
> >       - PERIPH: 40 MHz.
> >   * MT7628 and MT7688:
> >      - XTAL: 20 MHz or 40 MHz.
> >      - CPU: 575 or 580 MHz.
> >      - BUS: CPU / 3.
> >      - PCMI2S: 480 MHz.
> >      - PERIPH: 40 MHz.
> >   * MT7620:
> >      - XTAL: 20 MHz or 40 MHz.
> >      - PLL: XTAL, 480, 600 MHz.
> >      - CPU: depends on PLL and some mult and dividers.
> >      - BUS: depends on PLL and some mult and dividers.
> >      - PERIPH: 40 or XTAL MHz.
> >
> > MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of
> > register reads and predividers. To derive CPU and BUS frequencies in the
> > MT7620 SoC 'mt7620_calc_rate()' helper is used.
> > In the case XTAL can have different frequencies and we need a different
> > clock frequency for peripherals 'periph' clock in introduced.
> > The rest of the peripherals present in the SoC just follow their parent
> > frequencies.
> >
> > I am using 'mtmips' inside for ralink clock driver. This is aligned with
> > pinctrl series recently merged through pinctrl git tree [0].
> >
> > I am maintaining ralink as prefix for compatible strings after discussions
> > between Rob and Arinc in v2 of this series [1].
> >
> > Changes have been compile tested for:
> > - RT2880
> > - RT3883
> > - MT7620
> >
> > Changes have been properly tested in RT5350 SoC based board (ALL5003 board)
> > resulting in a working platform.
> >
> > Dts files for these SoCs in-tree except MT7621 are incomplete. We are
> > planning to align with openWRT files at some point and add extra needed
> > changes. Hence I am not touching them at all in these series. If this is
> > a problem, please let me know and I will update them.
> >
> > Talking about merging this series I'd like all of the patches going through
> > the MIPS tree if possible.
> >
> > Thanks in advance for your time.
> >
> > Best regards,
> >     Sergio Paracuellos
> >
> > Changes in v3:
> > - Address Stephen comments in v2:
> >     + Drop unsused include '<linux/clk.h>'.
> >     + Add fixed and factor clocks when it makes sense.
> >     + Make 'mtmips_periph_clk_ops' named variable.
> >     + WARN_ON -> WARN_ON_ONCE.
> >     + Avoid CONFIG_USB dependent code. Introduce new 'mtmips_clk_regs_init'.
> >     + Don't validate the bindings in the driver.
> >     + Make const 'struct clk_init_data' used inside macros.
> >     + do_div -> div_u64.
> >     + Make use of dev_err_probe.
>
> Hi Stephen,
>
> Does anything else need to be addressed to have all of these added?
>
> Philipp, can you please review the reset related code in PATCH 2/9 of
> these series?
>
> Thanks in advance for your time!
>
> Best regards,
>     Sergio Paracuellos

Gentle ping for this series :-)

Thanks,
    Sergio Paracuellos
>
> >
> > Changes in v2:
> > - Address bindings documentation changes pointed out by Krzysztof:
> >     + Rename the file into 'mediatek,mtmips-sysc.yaml'.
> >     + Redo commit subject and log message.
> >     + Order compatibles alphabetically.
> >     + Redo bindings description taking into account this is a system
> >       controller node which provides both clocks and resets to the world.
> >     + Drop label from example.
> >     + Use 'syscon' as node name in example.
> >     + Drop no sense 'ralink,rt2880-reset' compatible string
> > - Squash patches 6 and 7 together as pointed out by Stephen Boyd.
> >
> > Previoous series:
> > v2: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#t
> > v1: https://lore.kernel.org/linux-clk/20230320161823.1424278-1-sergio.paracuellos@gmail.com/T/#t
> >
> > [0]: https://lore.kernel.org/linux-gpio/e9e6ad87-2db5-9767-ff39-64a302b06185@arinc9.com/T/#t
> > [1]: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#mfe725b6e3382c6fb09736472a846cbbc84f264dc
> >
> > Sergio Paracuellos (9):
> >   dt-bindings: clock: add mtmips SoCs system controller
> >   clk: ralink: add clock and reset driver for MTMIPS SoCs
> >   mips: ralink: rt288x: remove clock related code
> >   mips: ralink: rt305x: remove clock related code
> >   mips: ralink: rt3883: remove clock related code
> >   mips: ralink: mt7620: remove clock related code
> >   mips: ralink: remove reset related code
> >   mips: ralink: get cpu rate from new driver code
> >   MAINTAINERS: add Mediatek MTMIPS Clock maintainer
> >
> >  .../bindings/clock/mediatek,mtmips-sysc.yaml  |   65 +
> >  MAINTAINERS                                   |    6 +
> >  arch/mips/include/asm/mach-ralink/mt7620.h    |   35 -
> >  arch/mips/include/asm/mach-ralink/rt288x.h    |   10 -
> >  arch/mips/include/asm/mach-ralink/rt305x.h    |   21 -
> >  arch/mips/include/asm/mach-ralink/rt3883.h    |    8 -
> >  arch/mips/ralink/clk.c                        |   26 +-
> >  arch/mips/ralink/common.h                     |    5 -
> >  arch/mips/ralink/mt7620.c                     |  226 ----
> >  arch/mips/ralink/of.c                         |    4 -
> >  arch/mips/ralink/reset.c                      |   61 -
> >  arch/mips/ralink/rt288x.c                     |   31 -
> >  arch/mips/ralink/rt305x.c                     |   78 --
> >  arch/mips/ralink/rt3883.c                     |   44 -
> >  drivers/clk/ralink/Kconfig                    |    7 +
> >  drivers/clk/ralink/Makefile                   |    1 +
> >  drivers/clk/ralink/clk-mtmips.c               | 1134 +++++++++++++++++
> >  17 files changed, 1232 insertions(+), 530 deletions(-)
> >  create mode 100644 Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml
> >  create mode 100644 drivers/clk/ralink/clk-mtmips.c
> >
> > --
> > 2.25.1
> >
  

On Tue, May 23, 2023 at 11:47 AM Sergio Paracuellos
<sergio.paracuellos@gmail.com> wrote:
>
> On Thu, May 4, 2023 at 4:48 PM Sergio Paracuellos
> <sergio.paracuellos@gmail.com> wrote:
> >
> > On Tue, Apr 18, 2023 at 11:03 AM Sergio Paracuellos
> > <sergio.paracuellos@gmail.com> wrote:
> > >
> > > Hi all!
> > >
> > > This patchset is a big effort to properly implement a clock and reset
> > > driver for old ralink SoCs. This allow to properly define clocks in
> > > device tree and avoid to use fixed-clocks directly from 'arch/mips/ralink'
> > > architecture directory code.
> > >
> > > Device tree 'sysc' node will be both clock and reset provider using
> > > 'clock-cells' and 'reset-cells' properties.
> > >
> > > The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350,
> > > RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in
> > > this new driver has been extracted from 'arch/mips/ralink' and cleanly
> > > put using kernel clock and reset driver APIs. The clock plans for this
> > > SoCs only talks about relation between CPU frequency and BUS frequency.
> > > This relation is different depending on the particular SoC. CPU clock is
> > > derived from XTAL frequencies.
> > >
> > >  Depending on the SoC we have the following frequencies:
> > >  * RT2880 SoC:
> > >      - XTAL: 40 MHz.
> > >      - CPU: 250, 266, 280 or 300 MHz.
> > >      - BUS: CPU / 2 MHz.
> > >   * RT3050, RT3052, RT3350:
> > >      - XTAL: 40 MHz.
> > >      - CPU: 320 or 384 MHz.
> > >      - BUS: CPU / 3 MHz.
> > >   * RT3352:
> > >      - XTAL: 40 MHz.
> > >      - CPU: 384 or 400 MHz.
> > >      - BUS: CPU / 3 MHz.
> > >      - PERIPH: 40 MHz.
> > >   * RT3383:
> > >      - XTAL: 40 MHz.
> > >      - CPU: 250, 384, 480 or 500 MHz.
> > >      - BUS: Depends on RAM Type and CPU:
> > >        + RAM DDR2: 125. ELSE 83 MHz.
> > >        + RAM DDR2: 128. ELSE 96 MHz.
> > >        + RAM DDR2: 160. ELSE 120 MHz.
> > >        + RAM DDR2: 166. ELSE 125 MHz.
> > >   * RT5350:
> > >       - XTAL: 40 MHz.
> > >       - CPU: 300, 320 or 360 MHz.
> > >       - BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
> > >       - PERIPH: 40 MHz.
> > >   * MT7628 and MT7688:
> > >      - XTAL: 20 MHz or 40 MHz.
> > >      - CPU: 575 or 580 MHz.
> > >      - BUS: CPU / 3.
> > >      - PCMI2S: 480 MHz.
> > >      - PERIPH: 40 MHz.
> > >   * MT7620:
> > >      - XTAL: 20 MHz or 40 MHz.
> > >      - PLL: XTAL, 480, 600 MHz.
> > >      - CPU: depends on PLL and some mult and dividers.
> > >      - BUS: depends on PLL and some mult and dividers.
> > >      - PERIPH: 40 or XTAL MHz.
> > >
> > > MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of
> > > register reads and predividers. To derive CPU and BUS frequencies in the
> > > MT7620 SoC 'mt7620_calc_rate()' helper is used.
> > > In the case XTAL can have different frequencies and we need a different
> > > clock frequency for peripherals 'periph' clock in introduced.
> > > The rest of the peripherals present in the SoC just follow their parent
> > > frequencies.
> > >
> > > I am using 'mtmips' inside for ralink clock driver. This is aligned with
> > > pinctrl series recently merged through pinctrl git tree [0].
> > >
> > > I am maintaining ralink as prefix for compatible strings after discussions
> > > between Rob and Arinc in v2 of this series [1].
> > >
> > > Changes have been compile tested for:
> > > - RT2880
> > > - RT3883
> > > - MT7620
> > >
> > > Changes have been properly tested in RT5350 SoC based board (ALL5003 board)
> > > resulting in a working platform.
> > >
> > > Dts files for these SoCs in-tree except MT7621 are incomplete. We are
> > > planning to align with openWRT files at some point and add extra needed
> > > changes. Hence I am not touching them at all in these series. If this is
> > > a problem, please let me know and I will update them.
> > >
> > > Talking about merging this series I'd like all of the patches going through
> > > the MIPS tree if possible.
> > >
> > > Thanks in advance for your time.
> > >
> > > Best regards,
> > >     Sergio Paracuellos
> > >
> > > Changes in v3:
> > > - Address Stephen comments in v2:
> > >     + Drop unsused include '<linux/clk.h>'.
> > >     + Add fixed and factor clocks when it makes sense.
> > >     + Make 'mtmips_periph_clk_ops' named variable.
> > >     + WARN_ON -> WARN_ON_ONCE.
> > >     + Avoid CONFIG_USB dependent code. Introduce new 'mtmips_clk_regs_init'.
> > >     + Don't validate the bindings in the driver.
> > >     + Make const 'struct clk_init_data' used inside macros.
> > >     + do_div -> div_u64.
> > >     + Make use of dev_err_probe.
> >
> > Hi Stephen,
> >
> > Does anything else need to be addressed to have all of these added?
> >
> > Philipp, can you please review the reset related code in PATCH 2/9 of
> > these series?
> >
> > Thanks in advance for your time!
> >
> > Best regards,
> >     Sergio Paracuellos
>
> Gentle ping for this series :-)

Another gentle ping for this series :-)

Thanks,
    Sergio Paracuellos
>
> Thanks,
>     Sergio Paracuellos
> >
> > >
> > > Changes in v2:
> > > - Address bindings documentation changes pointed out by Krzysztof:
> > >     + Rename the file into 'mediatek,mtmips-sysc.yaml'.
> > >     + Redo commit subject and log message.
> > >     + Order compatibles alphabetically.
> > >     + Redo bindings description taking into account this is a system
> > >       controller node which provides both clocks and resets to the world.
> > >     + Drop label from example.
> > >     + Use 'syscon' as node name in example.
> > >     + Drop no sense 'ralink,rt2880-reset' compatible string
> > > - Squash patches 6 and 7 together as pointed out by Stephen Boyd.
> > >
> > > Previoous series:
> > > v2: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#t
> > > v1: https://lore.kernel.org/linux-clk/20230320161823.1424278-1-sergio.paracuellos@gmail.com/T/#t
> > >
> > > [0]: https://lore.kernel.org/linux-gpio/e9e6ad87-2db5-9767-ff39-64a302b06185@arinc9.com/T/#t
> > > [1]: https://lore.kernel.org/linux-clk/CAMhs-H-BfZb3mD8E=LeJ4vT22uibQ1DnaZsfTrtRxSiv=8L5RA@mail.gmail.com/T/#mfe725b6e3382c6fb09736472a846cbbc84f264dc
> > >
> > > Sergio Paracuellos (9):
> > >   dt-bindings: clock: add mtmips SoCs system controller
> > >   clk: ralink: add clock and reset driver for MTMIPS SoCs
> > >   mips: ralink: rt288x: remove clock related code
> > >   mips: ralink: rt305x: remove clock related code
> > >   mips: ralink: rt3883: remove clock related code
> > >   mips: ralink: mt7620: remove clock related code
> > >   mips: ralink: remove reset related code
> > >   mips: ralink: get cpu rate from new driver code
> > >   MAINTAINERS: add Mediatek MTMIPS Clock maintainer
> > >
> > >  .../bindings/clock/mediatek,mtmips-sysc.yaml  |   65 +
> > >  MAINTAINERS                                   |    6 +
> > >  arch/mips/include/asm/mach-ralink/mt7620.h    |   35 -
> > >  arch/mips/include/asm/mach-ralink/rt288x.h    |   10 -
> > >  arch/mips/include/asm/mach-ralink/rt305x.h    |   21 -
> > >  arch/mips/include/asm/mach-ralink/rt3883.h    |    8 -
> > >  arch/mips/ralink/clk.c                        |   26 +-
> > >  arch/mips/ralink/common.h                     |    5 -
> > >  arch/mips/ralink/mt7620.c                     |  226 ----
> > >  arch/mips/ralink/of.c                         |    4 -
> > >  arch/mips/ralink/reset.c                      |   61 -
> > >  arch/mips/ralink/rt288x.c                     |   31 -
> > >  arch/mips/ralink/rt305x.c                     |   78 --
> > >  arch/mips/ralink/rt3883.c                     |   44 -
> > >  drivers/clk/ralink/Kconfig                    |    7 +
> > >  drivers/clk/ralink/Makefile                   |    1 +
> > >  drivers/clk/ralink/clk-mtmips.c               | 1134 +++++++++++++++++
> > >  17 files changed, 1232 insertions(+), 530 deletions(-)
> > >  create mode 100644 Documentation/devicetree/bindings/clock/mediatek,mtmips-sysc.yaml
> > >  create mode 100644 drivers/clk/ralink/clk-mtmips.c
> > >
> > > --
> > > 2.25.1
> > >
  

On Fri, Jun 16, 2023 at 08:12:00AM +0200, Sergio Paracuellos wrote:
> On Tue, May 23, 2023 at 11:47 AM Sergio Paracuellos
> <sergio.paracuellos@gmail.com> wrote:
> >
> > On Thu, May 4, 2023 at 4:48 PM Sergio Paracuellos
> > <sergio.paracuellos@gmail.com> wrote:
> > >
> > > On Tue, Apr 18, 2023 at 11:03 AM Sergio Paracuellos
> > > <sergio.paracuellos@gmail.com> wrote:
> > > >
> > > > Hi all!
> > > >
> > > > This patchset is a big effort to properly implement a clock and reset
> > > > driver for old ralink SoCs. This allow to properly define clocks in
> > > > device tree and avoid to use fixed-clocks directly from 'arch/mips/ralink'
> > > > architecture directory code.
> > > >
> > > > Device tree 'sysc' node will be both clock and reset provider using
> > > > 'clock-cells' and 'reset-cells' properties.
> > > >
> > > > The ralink SoCs we are taking about are RT2880, RT3050, RT3052, RT3350,
> > > > RT3352, RT3883, RT5350, MT7620, MT7628 and MT7688. Mostly the code in
> > > > this new driver has been extracted from 'arch/mips/ralink' and cleanly
> > > > put using kernel clock and reset driver APIs. The clock plans for this
> > > > SoCs only talks about relation between CPU frequency and BUS frequency.
> > > > This relation is different depending on the particular SoC. CPU clock is
> > > > derived from XTAL frequencies.
> > > >
> > > >  Depending on the SoC we have the following frequencies:
> > > >  * RT2880 SoC:
> > > >      - XTAL: 40 MHz.
> > > >      - CPU: 250, 266, 280 or 300 MHz.
> > > >      - BUS: CPU / 2 MHz.
> > > >   * RT3050, RT3052, RT3350:
> > > >      - XTAL: 40 MHz.
> > > >      - CPU: 320 or 384 MHz.
> > > >      - BUS: CPU / 3 MHz.
> > > >   * RT3352:
> > > >      - XTAL: 40 MHz.
> > > >      - CPU: 384 or 400 MHz.
> > > >      - BUS: CPU / 3 MHz.
> > > >      - PERIPH: 40 MHz.
> > > >   * RT3383:
> > > >      - XTAL: 40 MHz.
> > > >      - CPU: 250, 384, 480 or 500 MHz.
> > > >      - BUS: Depends on RAM Type and CPU:
> > > >        + RAM DDR2: 125. ELSE 83 MHz.
> > > >        + RAM DDR2: 128. ELSE 96 MHz.
> > > >        + RAM DDR2: 160. ELSE 120 MHz.
> > > >        + RAM DDR2: 166. ELSE 125 MHz.
> > > >   * RT5350:
> > > >       - XTAL: 40 MHz.
> > > >       - CPU: 300, 320 or 360 MHz.
> > > >       - BUS: CPU / 3, CPU / 4, CPU / 3 MHz.
> > > >       - PERIPH: 40 MHz.
> > > >   * MT7628 and MT7688:
> > > >      - XTAL: 20 MHz or 40 MHz.
> > > >      - CPU: 575 or 580 MHz.
> > > >      - BUS: CPU / 3.
> > > >      - PCMI2S: 480 MHz.
> > > >      - PERIPH: 40 MHz.
> > > >   * MT7620:
> > > >      - XTAL: 20 MHz or 40 MHz.
> > > >      - PLL: XTAL, 480, 600 MHz.
> > > >      - CPU: depends on PLL and some mult and dividers.
> > > >      - BUS: depends on PLL and some mult and dividers.
> > > >      - PERIPH: 40 or XTAL MHz.
> > > >
> > > > MT7620 is a bit more complex deriving CPU clock from a PLL and an bunch of
> > > > register reads and predividers. To derive CPU and BUS frequencies in the
> > > > MT7620 SoC 'mt7620_calc_rate()' helper is used.
> > > > In the case XTAL can have different frequencies and we need a different
> > > > clock frequency for peripherals 'periph' clock in introduced.
> > > > The rest of the peripherals present in the SoC just follow their parent
> > > > frequencies.
> > > >
> > > > I am using 'mtmips' inside for ralink clock driver. This is aligned with
> > > > pinctrl series recently merged through pinctrl git tree [0].
> > > >
> > > > I am maintaining ralink as prefix for compatible strings after discussions
> > > > between Rob and Arinc in v2 of this series [1].
> > > >
> > > > Changes have been compile tested for:
> > > > - RT2880
> > > > - RT3883
> > > > - MT7620
> > > >
> > > > Changes have been properly tested in RT5350 SoC based board (ALL5003 board)
> > > > resulting in a working platform.
> > > >
> > > > Dts files for these SoCs in-tree except MT7621 are incomplete. We are
> > > > planning to align with openWRT files at some point and add extra needed
> > > > changes. Hence I am not touching them at all in these series. If this is
> > > > a problem, please let me know and I will update them.
> > > >
> > > > Talking about merging this series I'd like all of the patches going through
> > > > the MIPS tree if possible.
> > > >
> > > > Thanks in advance for your time.
> > > >
> > > > Best regards,
> > > >     Sergio Paracuellos
> > > >
> > > > Changes in v3:
> > > > - Address Stephen comments in v2:
> > > >     + Drop unsused include '<linux/clk.h>'.
> > > >     + Add fixed and factor clocks when it makes sense.
> > > >     + Make 'mtmips_periph_clk_ops' named variable.
> > > >     + WARN_ON -> WARN_ON_ONCE.
> > > >     + Avoid CONFIG_USB dependent code. Introduce new 'mtmips_clk_regs_init'.
> > > >     + Don't validate the bindings in the driver.
> > > >     + Make const 'struct clk_init_data' used inside macros.
> > > >     + do_div -> div_u64.
> > > >     + Make use of dev_err_probe.
> > >
> > > Hi Stephen,
> > >
> > > Does anything else need to be addressed to have all of these added?
> > >
> > > Philipp, can you please review the reset related code in PATCH 2/9 of
> > > these series?
> > >
> > > Thanks in advance for your time!
> > >
> > > Best regards,
> > >     Sergio Paracuellos
> >
> > Gentle ping for this series :-)
> 
> Another gentle ping for this series :-)

I'm reday to take it through the MIPS tree, if Stephen acks the
clk driver changes.

Thomas.