mbox series

[v3,0/9] arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs

Message ID 20230216125257.112300-1-brgl@bgdev.pl
Headers
Series arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs |

Message

Bartosz Golaszewski Feb. 16, 2023, 12:52 p.m. UTC 
  From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

This enables the QUPv3 interfaces that are exposed on the sa8775p-ride
board: I2C, SPI and the Bluetooth and GNSS UART ports.

v2 -> v3:
- fix the interrupt number for uart12
- replace underscores with hyphens in DT node names (although make dtbs_check
  does not raise warnings about this)
- rearrange the commits so that they're more fine-grained with separate
  patches for adding nodes to dtsi and enabling them for the board

v1 -> v2:
- uart17 is the Bluetooth port, not GNSS
- add uart12 for GNSS too in that case

Bartosz Golaszewski (9):
  arm64: dts: qcom: sa8775p: add the QUPv3 #2 node
  arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2
  arm64: dts: qcom: sa8775p: add the i2c18 node
  arm64: dts: qcom: sa8775p-ride: enable i2c18
  arm64: dts: qcom: sa8775p: add the spi16 node
  arm64: dts: qcom: sa8775p-ride: enable the SPI node
  arm64: dts: qcom: sa8775p: add high-speed UART nodes
  arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port
  arm64: dts: qcom: sa8775p-ride: enable the BT UART port

 arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 100 ++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sa8775p.dtsi     |  86 +++++++++++++++++++
 2 files changed, 186 insertions(+)

Comments

Bartosz Golaszewski March 6, 2023, 1:28 p.m. UTC | #1 
On Thu, Feb 16, 2023 at 1:53 PM Bartosz Golaszewski <brgl@bgdev.pl> wrote:
>
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
>
> This enables the QUPv3 interfaces that are exposed on the sa8775p-ride
> board: I2C, SPI and the Bluetooth and GNSS UART ports.
>
> v2 -> v3:
> - fix the interrupt number for uart12
> - replace underscores with hyphens in DT node names (although make dtbs_check
>   does not raise warnings about this)
> - rearrange the commits so that they're more fine-grained with separate
>   patches for adding nodes to dtsi and enabling them for the board
>
> v1 -> v2:
> - uart17 is the Bluetooth port, not GNSS
> - add uart12 for GNSS too in that case
>
> Bartosz Golaszewski (9):
>   arm64: dts: qcom: sa8775p: add the QUPv3 #2 node
>   arm64: dts: qcom: sa8775p-ride: enable QUPv3 #2
>   arm64: dts: qcom: sa8775p: add the i2c18 node
>   arm64: dts: qcom: sa8775p-ride: enable i2c18
>   arm64: dts: qcom: sa8775p: add the spi16 node
>   arm64: dts: qcom: sa8775p-ride: enable the SPI node
>   arm64: dts: qcom: sa8775p: add high-speed UART nodes
>   arm64: dts: qcom: sa8775p-ride: enable the GNSS UART port
>   arm64: dts: qcom: sa8775p-ride: enable the BT UART port
>
>  arch/arm64/boot/dts/qcom/sa8775p-ride.dts | 100 ++++++++++++++++++++++
>  arch/arm64/boot/dts/qcom/sa8775p.dtsi     |  86 +++++++++++++++++++
>  2 files changed, 186 insertions(+)
>
> --
> 2.37.2
>

Konrad, Krzysztof et al,

It's been over two weeks, could you please take a look and let me know
if this is good to go?

Thanks,
Bartosz