diff mbox series

[RFC,net-next,2/2] net: dsa: mt7530: introduce MMIO driver for MT7988 SoC

Message ID ZCIML310vc8/uoM4@makrotopia.org
State New
Headers
Series net: dsa: add support for MT7988 |

Commit Message

Daniel Golle March 27, 2023, 9:35 p.m. UTC 
  The MediaTek MT7988 SoC comes with a built-in switch very similar to
previous MT7530 and MT7531. However, the switch address space is mapped
into the SoCs memory space rather than being connected via MDIO.
Using MMIO simplifies register access and also removes the need for a bus
lock, and for that reason also makes interrupt handling more light-weight.

Note that this is different from previous SoCs like MT7621 and MT7623N
which also came with an integrated MT7530-like switch which yet had to be
accessed via MDIO.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
 drivers/net/dsa/Kconfig       |   8 ++
 drivers/net/dsa/Makefile      |   1 +
 drivers/net/dsa/mt7530-mmio.c | 126 +++++++++++++++++++++
 drivers/net/dsa/mt7530.c      | 203 ++++++++++++++++++++++++++++++----
 drivers/net/dsa/mt7530.h      |  16 ++-
 5 files changed, 324 insertions(+), 30 deletions(-)
 create mode 100644 drivers/net/dsa/mt7530-mmio.c

Comments

Andrew Lunn March 28, 2023, 1:58 a.m. UTC | #1 
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -118,6 +118,9 @@ core_write_mmd_indirect(struct mt7530_priv *priv, int prtad,
>  	struct mii_bus *bus = priv->bus;
>  	int ret;
>  
> +	if (!bus)
> +		return 0;
> +
>  	/* Write the desired MMD Devad */
>  	ret = bus->write(bus, 0, MII_MMD_CTRL, devad);
>  	if (ret < 0)
> @@ -147,11 +150,13 @@ core_write(struct mt7530_priv *priv, u32 reg, u32 val)
>  {
>  	struct mii_bus *bus = priv->bus;
>  
> -	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
> +	if (bus)
> +		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
>  
>  	core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val);
>  
> -	mutex_unlock(&bus->mdio_lock);
> +	if (bus)
> +		mutex_unlock(&bus->mdio_lock);
>  }
>  
>  static void
> @@ -160,6 +165,9 @@ core_rmw(struct mt7530_priv *priv, u32 reg, u32 mask, u32 set)
>  	struct mii_bus *bus = priv->bus;
>  	u32 val;
>  
> +	if (!bus)
> +		return;
> +
>  	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
>  
>  	val = core_read_mmd_indirect(priv, reg, MDIO_MMD_VEND2);
> @@ -189,6 +197,11 @@ mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val)
>  	u16 page, r, lo, hi;
>  	int ret;
>  
> +	if (priv->base_addr) {
> +		iowrite32(val, priv->base_addr + reg);
> +		return 0;
> +	}
> +
>  	page = (reg >> 6) & 0x3ff;
>  	r  = (reg >> 2) & 0xf;
>  	lo = val & 0xffff;
> @@ -218,6 +231,9 @@ mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
>  	u16 page, r, lo, hi;
>  	int ret;
>  
> +	if (priv->base_addr)
> +		return ioread32(priv->base_addr + reg);
> +
>  	page = (reg >> 6) & 0x3ff;
>  	r = (reg >> 2) & 0xf;
>  

This looks pretty ugly.

A much better way to do this is to use regmap. Take a look at xrs700x
and how it has both an i2c and an mdio version.

    Andrew
Daniel Golle March 28, 2023, 1:08 p.m. UTC | #2 
Hi Andrew,

On Tue, Mar 28, 2023 at 03:58:50AM +0200, Andrew Lunn wrote:
> > --- a/drivers/net/dsa/mt7530.c
> > +++ b/drivers/net/dsa/mt7530.c
> > @@ -118,6 +118,9 @@ core_write_mmd_indirect(struct mt7530_priv *priv, int prtad,
> >  	struct mii_bus *bus = priv->bus;
> >  	int ret;
> >  
> > +	if (!bus)
> > +		return 0;
> > +
> >  	/* Write the desired MMD Devad */
> >  	ret = bus->write(bus, 0, MII_MMD_CTRL, devad);
> >  	if (ret < 0)
> > @@ -147,11 +150,13 @@ core_write(struct mt7530_priv *priv, u32 reg, u32 val)
> >  {
> >  	struct mii_bus *bus = priv->bus;
> >  
> > -	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
> > +	if (bus)
> > +		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
> >  
> >  	core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val);
> >  
> > -	mutex_unlock(&bus->mdio_lock);
> > +	if (bus)
> > +		mutex_unlock(&bus->mdio_lock);
> >  }
> >  
> >  static void
> > @@ -160,6 +165,9 @@ core_rmw(struct mt7530_priv *priv, u32 reg, u32 mask, u32 set)
> >  	struct mii_bus *bus = priv->bus;
> >  	u32 val;
> >  
> > +	if (!bus)
> > +		return;
> > +
> >  	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
> >  
> >  	val = core_read_mmd_indirect(priv, reg, MDIO_MMD_VEND2);
> > @@ -189,6 +197,11 @@ mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val)
> >  	u16 page, r, lo, hi;
> >  	int ret;
> >  
> > +	if (priv->base_addr) {
> > +		iowrite32(val, priv->base_addr + reg);
> > +		return 0;
> > +	}
> > +
> >  	page = (reg >> 6) & 0x3ff;
> >  	r  = (reg >> 2) & 0xf;
> >  	lo = val & 0xffff;
> > @@ -218,6 +231,9 @@ mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
> >  	u16 page, r, lo, hi;
> >  	int ret;
> >  
> > +	if (priv->base_addr)
> > +		return ioread32(priv->base_addr + reg);
> > +
> >  	page = (reg >> 6) & 0x3ff;
> >  	r = (reg >> 2) & 0xf;
> >  
> 
> This looks pretty ugly.
> 
> A much better way to do this is to use regmap. Take a look at xrs700x
> and how it has both an i2c and an mdio version.

I agree that using regmap would be better and I have evaluated that
approach as well. As regmap doesn't allow lock-skipping and mt7530.c is
much more complex than xrs700x in the way indirect access to its MDIO bus
and interrupts work, using regmap accessors for everything would not be
trivial.

To illustrate what I'm talking about, let me show some examples in the
current code for which I don't see a way to use regmap:
634) static int
635) mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad,
636)                   int regnum)
637) {
638)   struct mii_bus *bus = priv->bus;
639)   struct mt7530_dummy_poll p;
640)   u32 reg, val;
641)   int ret;
642) 
643)   INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
644) 
645)   mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
646) 
647)   ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
648)                            !(val & MT7531_PHY_ACS_ST), 20, 100000);
649)   if (ret < 0) {
650)           dev_err(priv->dev, "poll timeout\n");
651)           goto out;
652)   }
653) 
654)   reg = MT7531_MDIO_CL45_ADDR | MT7531_MDIO_PHY_ADDR(port) |
655)         MT7531_MDIO_DEV_ADDR(devad) | regnum;
656)   mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);
657) 
658)   ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
659)                            !(val & MT7531_PHY_ACS_ST), 20, 100000);
660)   if (ret < 0) {
661)           dev_err(priv->dev, "poll timeout\n");
662)           goto out;
663)   }
664) 
665)   reg = MT7531_MDIO_CL45_READ | MT7531_MDIO_PHY_ADDR(port) |
666)         MT7531_MDIO_DEV_ADDR(devad);
667)   mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);
668) 
669)   ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
670)                            !(val & MT7531_PHY_ACS_ST), 20, 100000);
671)   if (ret < 0) {
672)           dev_err(priv->dev, "poll timeout\n");
673)           goto out;
674)   }
675) 
676)   ret = val & MT7531_MDIO_RW_DATA_MASK;
677) out:
678)   mutex_unlock(&bus->mdio_lock);
679) 
680)   return ret;
681) }

So here we can of course use regmap_read_poll_timeout and a bunch of
readmap_write operations. However, each of them will individually acquire
and release the mdio bus mutex while the current code acquires the lock
at the top of the function and then uses unlocked operations.
regmap currently doesn't offer any way to skip the locking and/or perform
locking manually. regmap_read, regmap_write, regmap_update_bits, ... always
acquire and release the lock on each operation.

While in the above example this might just imply a performance hit, look
here:

1958) static void
1959) mt7530_irq_bus_sync_unlock(struct irq_data *d)
1960) {
1961)   struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
1962) 
1963)   mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable);
1964)   mutex_unlock(&priv->bus->mdio_lock);
1965) }

So in this case the lock has previously been acquired and the
register is written when releasing the lock.
The above function is being used as .irq_bus_sync_unlock...

Hence there are two ways to go:
1. Extend regmap to allow callers to perform locking manually and
   provide unlocked variants of all operations.
   This would allow us to then convert all the mt7530_{read,write,rmw},
   mt7530_mii_{read,write}, ... calls to use regmap_* calls instead.

2. Use regmap to only provide locked access and keep open-coding the
   cases where unlocked access is used while manually acquiring the
   bus mutex in such cases, as it is the case now.

3. Use regmap to only provide unlocked access to beging with and
   keep taking care of locking in mt7530.c as it is now. This would be
   easy, but then all those ugly checks you criticized would still
   be needed. Ie. `if (priv->base_addr) ...` would of course go away,
   but all the other `if (priv->bus) ...` checks would have to stay.

Let me know what you think and how I should proceed.


Thank you!


Best regards


Daniel
Andrew Lunn March 28, 2023, 1:59 p.m. UTC | #3 
> I agree that using regmap would be better and I have evaluated that
> approach as well. As regmap doesn't allow lock-skipping and mt7530.c is
> much more complex than xrs700x in the way indirect access to its MDIO bus
> and interrupts work, using regmap accessors for everything would not be
> trivial.

O.K, so lets go another way.

Study the low level accesors, and put an abstraction over
them. Provide an MDIO set and an MMIO set.

> To illustrate what I'm talking about, let me show some examples in the
> current code for which I don't see a way to use regmap:
> 634) static int
> 635) mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad,
> 636)                   int regnum)
> 637) {
> 638)   struct mii_bus *bus = priv->bus;
> 639)   struct mt7530_dummy_poll p;
> 640)   u32 reg, val;
> 641)   int ret;
> 642) 
> 643)   INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
> 644) 
> 645)   mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);

So you need an abstract lock() and an unlock(). Maybe the MMIO
implementation is a NOP? And the MDIO implementation does a real lock?

> 646) 
> 647)   ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
> 648)                            !(val & MT7531_PHY_ACS_ST), 20, 100000);

_mt7530_unlocked_read and presumably _mt7530_unlocked_write()?

> 649)   if (ret < 0) {
> 650)           dev_err(priv->dev, "poll timeout\n");
> 651)           goto out;
> 652)   }
> 653) 
> 654)   reg = MT7531_MDIO_CL45_ADDR | MT7531_MDIO_PHY_ADDR(port) |
> 655)         MT7531_MDIO_DEV_ADDR(devad) | regnum;
> 656)   mt7530_mii_write(priv, MT7531_PHY_IAC, reg | MT7531_PHY_ACS_ST);

mt7530_write() and mt7530_read()

Put the MDIO accessors in the _mdio.c file, and the MMIO accessors in
the _mmio.c file. Pass them to the core. If you have the abstraction
correct, the core should not care how the registers are accessed.

	 Andrew
Vladimir Oltean March 28, 2023, 2:16 p.m. UTC | #4 
On Tue, Mar 28, 2023 at 02:08:18PM +0100, Daniel Golle wrote:
> I agree that using regmap would be better and I have evaluated that
> approach as well. As regmap doesn't allow lock-skipping and mt7530.c is
> much more complex than xrs700x in the way indirect access to its MDIO bus
> and interrupts work, using regmap accessors for everything would not be
> trivial.
> 
> So here we can of course use regmap_read_poll_timeout and a bunch of
> readmap_write operations. However, each of them will individually acquire
> and release the mdio bus mutex while the current code acquires the lock
> at the top of the function and then uses unlocked operations.
> regmap currently doesn't offer any way to skip the locking and/or perform
> locking manually. regmap_read, regmap_write, regmap_update_bits, ... always
> acquire and release the lock on each operation.

What does struct regmap_config :: disable_locking do?
Daniel Golle March 28, 2023, 3 p.m. UTC | #5 
On Tue, Mar 28, 2023 at 05:16:28PM +0300, Vladimir Oltean wrote:
> On Tue, Mar 28, 2023 at 02:08:18PM +0100, Daniel Golle wrote:
> > I agree that using regmap would be better and I have evaluated that
> > approach as well. As regmap doesn't allow lock-skipping and mt7530.c is
> > much more complex than xrs700x in the way indirect access to its MDIO bus
> > and interrupts work, using regmap accessors for everything would not be
> > trivial.
> > 
> > So here we can of course use regmap_read_poll_timeout and a bunch of
> > readmap_write operations. However, each of them will individually acquire
> > and release the mdio bus mutex while the current code acquires the lock
> > at the top of the function and then uses unlocked operations.
> > regmap currently doesn't offer any way to skip the locking and/or perform
> > locking manually. regmap_read, regmap_write, regmap_update_bits, ... always
> > acquire and release the lock on each operation.
> 
> What does struct regmap_config :: disable_locking do?

I thought I can't use that on a per-operation base because the
instance of struct regmap_config itself isn't protected by any lock
and hence setting disable_locking=false before calling one of the
accessor functions may affect also other congruent calls to the
accessors which will then ignore locking and screw things up.
Please correct me if I'm wrong there.

Yet another way I thought about now could also be to have two regmap
instances, one for locked and one for unlocked accessed to the same
regmap_bus.
Vladimir Oltean March 28, 2023, 3:17 p.m. UTC | #6 
On Tue, Mar 28, 2023 at 04:00:30PM +0100, Daniel Golle wrote:
> On Tue, Mar 28, 2023 at 05:16:28PM +0300, Vladimir Oltean wrote:
> > On Tue, Mar 28, 2023 at 02:08:18PM +0100, Daniel Golle wrote:
> > > I agree that using regmap would be better and I have evaluated that
> > > approach as well. As regmap doesn't allow lock-skipping and mt7530.c is
> > > much more complex than xrs700x in the way indirect access to its MDIO bus
> > > and interrupts work, using regmap accessors for everything would not be
> > > trivial.
> > > 
> > > So here we can of course use regmap_read_poll_timeout and a bunch of
> > > readmap_write operations. However, each of them will individually acquire
> > > and release the mdio bus mutex while the current code acquires the lock
> > > at the top of the function and then uses unlocked operations.
> > > regmap currently doesn't offer any way to skip the locking and/or perform
> > > locking manually. regmap_read, regmap_write, regmap_update_bits, ... always
> > > acquire and release the lock on each operation.
> > 
> > What does struct regmap_config :: disable_locking do?
> 
> I thought I can't use that on a per-operation base because the
> instance of struct regmap_config itself isn't protected by any lock
> and hence setting disable_locking=false before calling one of the
> accessor functions may affect also other congruent calls to the
> accessors which will then ignore locking and screw things up.
> Please correct me if I'm wrong there.

It's not supposed to be used like that. You set disable_locking = true
once, and take care of locking from the mt7530 driver. Not before every
operation.

> Yet another way I thought about now could also be to have two regmap
> instances, one for locked and one for unlocked accessed to the same
> regmap_bus.

That would also be theoretically possible, but the above would be
equivalent and would require a single regmap.
diff mbox series

Patch

diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
index 5a67a74166a3d..0120586df330d 100644
--- a/drivers/net/dsa/Kconfig
+++ b/drivers/net/dsa/Kconfig
@@ -50,6 +50,14 @@  config NET_DSA_MT7530_MDIO
 	  switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT,
 	  MT7621ST and MT7623AI SoCs is supported.
 
+config NET_DSA_MT7530_MMIO
+	tristate "MediaTek MT7988 built-in Ethernet switch support"
+	select NET_DSA_MT7530
+	depends on HAS_IOMEM
+	help
+	  This enables support for the MediaTek MT7988 Ethernet
+	  switch chip.
+
 config NET_DSA_MV88E6060
 	tristate "Marvell 88E6060 ethernet switch chip support"
 	select NET_DSA_TAG_TRAILER
diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile
index 2b072d574ed02..7c763578b297f 100644
--- a/drivers/net/dsa/Makefile
+++ b/drivers/net/dsa/Makefile
@@ -8,6 +8,7 @@  endif
 obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
 obj-$(CONFIG_NET_DSA_MT7530)		+= mt7530.o
 obj-$(CONFIG_NET_DSA_MT7530_MDIO)	+= mt7530-mdio.o
+obj-$(CONFIG_NET_DSA_MT7530_MMIO)	+= mt7530-mmio.o
 obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
 obj-$(CONFIG_NET_DSA_RZN1_A5PSW) += rzn1_a5psw.o
 obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
diff --git a/drivers/net/dsa/mt7530-mmio.c b/drivers/net/dsa/mt7530-mmio.c
new file mode 100644
index 0000000000000..8096315f17a95
--- /dev/null
+++ b/drivers/net/dsa/mt7530-mmio.c
@@ -0,0 +1,126 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <net/dsa.h>
+
+#include "mt7530.h"
+
+static const struct of_device_id mt7988_of_match[] = {
+	{ .compatible = "mediatek,mt7988-switch", .data = &mt753x_table[ID_MT7988], },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mt7988_of_match);
+
+static int
+mt7988_probe(struct platform_device *pdev)
+{
+	struct mt7530_priv *priv;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->base_addr = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(priv->base_addr)) {
+		dev_err(&pdev->dev, "cannot request I/O memory space\n");
+		return -ENXIO;
+	}
+
+	priv->ds = devm_kzalloc(&pdev->dev, sizeof(*priv->ds), GFP_KERNEL);
+	if (!priv->ds)
+		return -ENOMEM;
+
+	priv->ds->dev = &pdev->dev;
+	priv->ds->num_ports = MT7530_NUM_PORTS;
+
+	priv->rstc = devm_reset_control_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->rstc)) {
+		dev_err(&pdev->dev, "Couldn't get our reset line\n");
+		return PTR_ERR(priv->rstc);
+	}
+
+	/* Get the hardware identifier from the devicetree node.
+	 * We will need it for some of the clock and regulator setup.
+	 */
+	priv->info = of_device_get_match_data(&pdev->dev);
+	if (!priv->info)
+		return -EINVAL;
+
+	/* Sanity check if these required device operations are filled
+	 * properly.
+	 */
+	if (!priv->info->sw_setup || !priv->info->pad_setup ||
+	    !priv->info->phy_read_c22 || !priv->info->phy_write_c22 ||
+	    !priv->info->mac_port_get_caps ||
+	    !priv->info->mac_port_config)
+		return -EINVAL;
+
+	priv->id = priv->info->id;
+	priv->bus = NULL;
+	priv->dev = &pdev->dev;
+	priv->ds->priv = priv;
+	priv->ds->ops = &mt7530_switch_ops;
+	mutex_init(&priv->reg_mutex);
+	dev_set_drvdata(&pdev->dev, priv);
+
+	return dsa_register_switch(priv->ds);
+}
+
+static int
+mt7988_remove(struct platform_device *pdev)
+{
+	struct mt7530_priv *priv = platform_get_drvdata(pdev);
+	int ret = 0;
+
+	if (!priv)
+		return 0;
+
+	ret = regulator_disable(priv->core_pwr);
+	if (ret < 0)
+		dev_err(priv->dev,
+			"Failed to disable core power: %d\n", ret);
+
+	ret = regulator_disable(priv->io_pwr);
+	if (ret < 0)
+		dev_err(priv->dev, "Failed to disable io pwr: %d\n",
+			ret);
+
+	if (priv->irq)
+		mt7530_free_irq(priv);
+
+	dsa_unregister_switch(priv->ds);
+
+	mutex_destroy(&priv->reg_mutex);
+
+	return 0;
+}
+
+static void mt7988_shutdown(struct platform_device *pdev)
+{
+	struct mt7530_priv *priv = platform_get_drvdata(pdev);
+
+	if (!priv)
+		return;
+
+	dsa_switch_shutdown(priv->ds);
+
+	dev_set_drvdata(&pdev->dev, NULL);
+}
+
+static struct platform_driver mt7988_platform_driver = {
+	.probe  = mt7988_probe,
+	.remove = mt7988_remove,
+	.shutdown = mt7988_shutdown,
+	.driver = {
+		.name = "mt7988-switch",
+		.of_match_table = mt7988_of_match,
+	},
+};
+module_platform_driver(mt7988_platform_driver);
+
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch (MMIO)");
+MODULE_LICENSE("GPL");
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 7828837d15e15..a5c3f69ea193d 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -118,6 +118,9 @@  core_write_mmd_indirect(struct mt7530_priv *priv, int prtad,
 	struct mii_bus *bus = priv->bus;
 	int ret;
 
+	if (!bus)
+		return 0;
+
 	/* Write the desired MMD Devad */
 	ret = bus->write(bus, 0, MII_MMD_CTRL, devad);
 	if (ret < 0)
@@ -147,11 +150,13 @@  core_write(struct mt7530_priv *priv, u32 reg, u32 val)
 {
 	struct mii_bus *bus = priv->bus;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	core_write_mmd_indirect(priv, reg, MDIO_MMD_VEND2, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 }
 
 static void
@@ -160,6 +165,9 @@  core_rmw(struct mt7530_priv *priv, u32 reg, u32 mask, u32 set)
 	struct mii_bus *bus = priv->bus;
 	u32 val;
 
+	if (!bus)
+		return;
+
 	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	val = core_read_mmd_indirect(priv, reg, MDIO_MMD_VEND2);
@@ -189,6 +197,11 @@  mt7530_mii_write(struct mt7530_priv *priv, u32 reg, u32 val)
 	u16 page, r, lo, hi;
 	int ret;
 
+	if (priv->base_addr) {
+		iowrite32(val, priv->base_addr + reg);
+		return 0;
+	}
+
 	page = (reg >> 6) & 0x3ff;
 	r  = (reg >> 2) & 0xf;
 	lo = val & 0xffff;
@@ -218,6 +231,9 @@  mt7530_mii_read(struct mt7530_priv *priv, u32 reg)
 	u16 page, r, lo, hi;
 	int ret;
 
+	if (priv->base_addr)
+		return ioread32(priv->base_addr + reg);
+
 	page = (reg >> 6) & 0x3ff;
 	r = (reg >> 2) & 0xf;
 
@@ -240,11 +256,13 @@  mt7530_write(struct mt7530_priv *priv, u32 reg, u32 val)
 {
 	struct mii_bus *bus = priv->bus;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	mt7530_mii_write(priv, reg, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 }
 
 static u32
@@ -256,14 +274,16 @@  _mt7530_unlocked_read(struct mt7530_dummy_poll *p)
 static u32
 _mt7530_read(struct mt7530_dummy_poll *p)
 {
-	struct mii_bus		*bus = p->priv->bus;
+	struct mii_bus *bus = p->priv->bus;
 	u32 val;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	val = mt7530_mii_read(p->priv, p->reg);
 
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 
 	return val;
 }
@@ -284,14 +304,16 @@  mt7530_rmw(struct mt7530_priv *priv, u32 reg,
 	struct mii_bus *bus = priv->bus;
 	u32 val;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	val = mt7530_mii_read(priv, reg);
 	val &= ~mask;
 	val |= set;
 	mt7530_mii_write(priv, reg, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 }
 
 static void
@@ -642,7 +664,8 @@  mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad,
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
 				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
@@ -675,7 +698,8 @@  mt7531_ind_c45_phy_read(struct mt7530_priv *priv, int port, int devad,
 
 	ret = val & MT7531_MDIO_RW_DATA_MASK;
 out:
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 
 	return ret;
 }
@@ -691,7 +715,8 @@  mt7531_ind_c45_phy_write(struct mt7530_priv *priv, int port, int devad,
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
 				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
@@ -723,7 +748,8 @@  mt7531_ind_c45_phy_write(struct mt7530_priv *priv, int port, int devad,
 	}
 
 out:
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 
 	return ret;
 }
@@ -738,7 +764,8 @@  mt7531_ind_c22_phy_read(struct mt7530_priv *priv, int port, int regnum)
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, val,
 				 !(val & MT7531_PHY_ACS_ST), 20, 100000);
@@ -761,7 +788,8 @@  mt7531_ind_c22_phy_read(struct mt7530_priv *priv, int port, int regnum)
 
 	ret = val & MT7531_MDIO_RW_DATA_MASK;
 out:
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 
 	return ret;
 }
@@ -777,7 +805,8 @@  mt7531_ind_c22_phy_write(struct mt7530_priv *priv, int port, int regnum,
 
 	INIT_MT7530_DUMMY_POLL(&p, priv, MT7531_PHY_IAC);
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	ret = readx_poll_timeout(_mt7530_unlocked_read, &p, reg,
 				 !(reg & MT7531_PHY_ACS_ST), 20, 100000);
@@ -799,7 +828,8 @@  mt7531_ind_c22_phy_write(struct mt7530_priv *priv, int port, int regnum,
 	}
 
 out:
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 
 	return ret;
 }
@@ -1109,7 +1139,8 @@  mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 	if (!dsa_is_cpu_port(ds, port))
 		return 0;
 
-	mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (bus)
+		mutex_lock_nested(&bus->mdio_lock, MDIO_MUTEX_NESTED);
 
 	val = mt7530_mii_read(priv, MT7530_GMACCR);
 	val &= ~MAX_RX_PKT_LEN_MASK;
@@ -1130,7 +1161,8 @@  mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu)
 
 	mt7530_mii_write(priv, MT7530_GMACCR, val);
 
-	mutex_unlock(&bus->mdio_lock);
+	if (bus)
+		mutex_unlock(&bus->mdio_lock);
 
 	return 0;
 }
@@ -1931,10 +1963,14 @@  mt7530_irq_thread_fn(int irq, void *dev_id)
 	u32 val;
 	int p;
 
-	mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
+	if (priv->bus)
+		mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
+
 	val = mt7530_mii_read(priv, MT7530_SYS_INT_STS);
 	mt7530_mii_write(priv, MT7530_SYS_INT_STS, val);
-	mutex_unlock(&priv->bus->mdio_lock);
+
+	if (priv->bus)
+		mutex_unlock(&priv->bus->mdio_lock);
 
 	for (p = 0; p < MT7530_NUM_PHYS; p++) {
 		if (BIT(p) & val) {
@@ -2007,6 +2043,47 @@  static const struct irq_domain_ops mt7530_irq_domain_ops = {
 	.xlate = irq_domain_xlate_onecell,
 };
 
+static void
+mt7988_irq_mask(struct irq_data *d)
+{
+	struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
+
+	priv->irq_enable &= ~BIT(d->hwirq);
+	mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable);
+}
+
+static void
+mt7988_irq_unmask(struct irq_data *d)
+{
+	struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
+
+	priv->irq_enable |= BIT(d->hwirq);
+	mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable);
+}
+
+static struct irq_chip mt7988_irq_chip = {
+	.name = KBUILD_MODNAME,
+	.irq_mask = mt7988_irq_mask,
+	.irq_unmask = mt7988_irq_unmask,
+};
+
+static int
+mt7988_irq_map(struct irq_domain *domain, unsigned int irq,
+	       irq_hw_number_t hwirq)
+{
+	irq_set_chip_data(irq, domain->host_data);
+	irq_set_chip_and_handler(irq, &mt7988_irq_chip, handle_simple_irq);
+	irq_set_nested_thread(irq, true);
+	irq_set_noprobe(irq);
+
+	return 0;
+}
+
+static const struct irq_domain_ops mt7988_irq_domain_ops = {
+	.map = mt7988_irq_map,
+	.xlate = irq_domain_xlate_onecell,
+};
+
 static void
 mt7530_setup_mdio_irq(struct mt7530_priv *priv)
 {
@@ -2041,8 +2118,15 @@  mt7530_setup_irq(struct mt7530_priv *priv)
 		return priv->irq ? : -EINVAL;
 	}
 
-	priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
-						 &mt7530_irq_domain_ops, priv);
+	if (priv->id == ID_MT7988)
+		priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
+							 &mt7988_irq_domain_ops,
+							 priv);
+	else
+		priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
+							 &mt7530_irq_domain_ops,
+							 priv);
+
 	if (!priv->irq_domain) {
 		dev_err(dev, "failed to create IRQ domain\n");
 		return -ENOMEM;
@@ -2627,6 +2711,8 @@  mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 	case PHY_INTERFACE_MODE_NA:
 	case PHY_INTERFACE_MODE_1000BASEX:
 	case PHY_INTERFACE_MODE_2500BASEX:
+	case PHY_INTERFACE_MODE_USXGMII:
+	case PHY_INTERFACE_MODE_10GKR:
 		/* handled in SGMII PCS driver */
 		return 0;
 	default:
@@ -2751,7 +2837,9 @@  static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port,
 	 * variants.
 	 */
 	if (interface == PHY_INTERFACE_MODE_TRGMII ||
-	    (phy_interface_mode_is_8023z(interface))) {
+	    interface == PHY_INTERFACE_MODE_USXGMII ||
+	    interface == PHY_INTERFACE_MODE_10GKR ||
+	    phy_interface_mode_is_8023z(interface)) {
 		speed = SPEED_1000;
 		duplex = DUPLEX_FULL;
 	}
@@ -3029,6 +3117,60 @@  static int mt753x_set_mac_eee(struct dsa_switch *ds, int port,
 	return 0;
 }
 
+static int mt7988_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
+{
+	return 0;
+}
+
+static int mt7988_setup(struct dsa_switch *ds)
+{
+	struct mt7530_priv *priv = ds->priv;
+	u32 unused_pm = 0;
+	int i;
+
+	/* Reset the switch */
+	reset_control_assert(priv->rstc);
+	udelay(20);
+	reset_control_deassert(priv->rstc);
+	udelay(20);
+
+	/* Reset the switch PHYs */
+	mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_PHY_RST);
+
+	/* BPDU to CPU port */
+	mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
+		   BIT(MT7988_CPU_PORT));
+	mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
+		   MT753X_BPDU_CPU_ONLY);
+
+	/* Enable and reset MIB counters */
+	mt7530_mib_reset(ds);
+
+	for (i = 0; i < MT7530_NUM_PORTS; i++) {
+		/* Disable forwarding by default on all ports */
+		mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
+			   PCR_MATRIX_CLR);
+
+		mt7530_set(priv, MT7531_DBG_CNT(i), MT7531_DIS_CLR);
+
+		if (dsa_is_unused_port(ds, i))
+			unused_pm |= BIT(i);
+		else if (dsa_is_cpu_port(ds, i))
+			mt753x_cpu_port_enable(ds, i);
+		else
+			mt7530_port_disable(ds, i);
+
+		/* Enable consistent egress tag */
+		mt7530_rmw(priv, MT7530_PVC_P(i), PVC_EG_TAG_MASK,
+			   PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
+	}
+
+	ds->configure_vlan_while_not_filtering = true;
+
+	/* Flush the FDB table */
+	return mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
+}
+
 const struct dsa_switch_ops mt7530_switch_ops = {
 	.get_tag_protocol	= mtk_get_tag_protocol,
 	.setup			= mt753x_setup,
@@ -3103,6 +3245,19 @@  const struct mt753x_info mt753x_table[] = {
 		.mac_port_get_caps = mt7531_mac_port_get_caps,
 		.mac_port_config = mt7531_mac_config,
 	},
+	[ID_MT7988] = {
+		.id = ID_MT7988,
+		.pcs_ops = &mt7530_pcs_ops,
+		.sw_setup = mt7988_setup,
+		.phy_read_c22 = mt7531_ind_c22_phy_read,
+		.phy_write_c22 = mt7531_ind_c22_phy_write,
+		.phy_read_c45 = mt7531_ind_c45_phy_read,
+		.phy_write_c45 = mt7531_ind_c45_phy_write,
+		.pad_setup = mt7988_pad_setup,
+		.cpu_port_config = mt7531_cpu_port_config,
+		.mac_port_get_caps = mt7531_mac_port_get_caps,
+		.mac_port_config = mt7531_mac_config,
+	},
 };
 EXPORT_SYMBOL_GPL(mt753x_table);
 
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index e78ae5c8955ee..6d7f72cb8a2bb 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -11,6 +11,8 @@ 
 #define MT7530_NUM_FDB_RECORDS		2048
 #define MT7530_ALL_MEMBERS		0xff
 
+#define MT7988_CPU_PORT			6
+
 #define MTK_HDR_LEN	4
 #define MT7530_MAX_MTU	(15 * 1024 - ETH_HLEN - ETH_FCS_LEN - MTK_HDR_LEN)
 
@@ -18,6 +20,7 @@  enum mt753x_id {
 	ID_MT7530 = 0,
 	ID_MT7621 = 1,
 	ID_MT7531 = 2,
+	ID_MT7988 = 3,
 };
 
 #define	NUM_TRGMII_CTRL			5
@@ -54,11 +57,11 @@  enum mt753x_id {
 #define  MT7531_MIRROR_PORT_SET(x)	(((x) & MIRROR_MASK) << 16)
 #define  MT7531_CPU_PMAP_MASK		GENMASK(7, 0)
 
-#define MT753X_MIRROR_REG(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_REG(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_CFC : MT7530_MFC)
-#define MT753X_MIRROR_EN(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_EN(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_EN : MIRROR_EN)
-#define MT753X_MIRROR_MASK(id)		(((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_MASK(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
 					 MT7531_MIRROR_MASK : MIRROR_MASK)
 
 /* Registers for BPDU and PAE frame control*/
@@ -295,9 +298,8 @@  enum mt7530_vlan_port_acc_frm {
 					 MT7531_FORCE_DPX | \
 					 MT7531_FORCE_RX_FC | \
 					 MT7531_FORCE_TX_FC)
-#define  PMCR_FORCE_MODE_ID(id)		(((id) == ID_MT7531) ? \
-					 MT7531_FORCE_MODE : \
-					 PMCR_FORCE_MODE)
+#define  PMCR_FORCE_MODE_ID(id)		((((id) == ID_MT7531) || ((id) == ID_MT7988)) ?	\
+					 MT7531_FORCE_MODE : PMCR_FORCE_MODE)
 #define  PMCR_LINK_SETTINGS_MASK	(PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
 					 PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
 					 PMCR_TX_FC_EN | PMCR_RX_FC_EN | \
@@ -740,6 +742,7 @@  struct mt753x_info {
  * @core_pwr:		The power supplied into the core
  * @io_pwr:		The power supplied into the I/O
  * @reset:		The descriptor for GPIO line tied to its reset pin
+ * @base_addr:		MMIO address for the switch interface.
  * @mcm:		Flag for distinguishing if standalone IC or module
  *			coupling
  * @ports:		Holding the state among ports
@@ -760,6 +763,7 @@  struct mt7530_priv {
 	struct regulator	*core_pwr;
 	struct regulator	*io_pwr;
 	struct gpio_desc	*reset;
+	void __iomem		*base_addr;
 	const struct mt753x_info *info;
 	unsigned int		id;
 	bool			mcm;