diff mbox series

[1/4] dts: arm64: qcom: sdm845: add SLPI remoteproc

Message ID 20230325135114.21688-2-me@dylanvanassche.be
State New
Headers
Series Qualcomm SDM845 SLPI DSP enablement |

Commit Message

Dylan Van Assche March 25, 2023, 1:51 p.m. UTC 
  Add the SLPI remoteproc to the SDM845 Qualcomm SoC which is responsible
for exposing the sensors connected to the SoC. The SLPI communicates
over GLink edge 'dsps' and is similar to other DSPs e.g. ADSP or CDSP.
This patch allows the SLPI to boot and expose itself over QRTR as
service 400.

Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
---
 arch/arm64/boot/dts/qcom/sdm845.dtsi | 37 ++++++++++++++++++++++++++++
 1 file changed, 37 insertions(+)

Comments

Krzysztof Kozlowski March 26, 2023, 8:56 a.m. UTC | #1 
On 25/03/2023 14:51, Dylan Van Assche wrote:
> Add the SLPI remoteproc to the SDM845 Qualcomm SoC which is responsible
> for exposing the sensors connected to the SoC. The SLPI communicates
> over GLink edge 'dsps' and is similar to other DSPs e.g. ADSP or CDSP.
> This patch allows the SLPI to boot and expose itself over QRTR as
> service 400.
> 
> Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
> ---
>  arch/arm64/boot/dts/qcom/sdm845.dtsi | 37 ++++++++++++++++++++++++++++
>  1 file changed, 37 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> index 2f32179c7d1b..8dcfe6293762 100644
> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
> @@ -3311,6 +3311,43 @@ glink-edge {
>  			};
>  		};
>  
> +		slpi_pas: remoteproc@5c00000 {
> +			compatible = "qcom,sdm845-slpi-pas";
> +			reg = <0 0x5c00000 0 0x4000>;
> +
> +			interrupts-extended = <&intc GIC_SPI 494 IRQ_TYPE_EDGE_RISING>,
> +						<&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
> +						<&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
> +						<&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
> +						<&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready",
> +						"handover", "stop-ack";
> +
> +			clocks = <&rpmhcc RPMH_CXO_CLK>;
> +			clock-names = "xo";
> +
> +			qcom,qmp = <&aoss_qmp>;
> +
> +			power-domains = <&rpmhpd SDM845_CX>,
> +					<&rpmhpd SDM845_MX>;
> +			power-domain-names = "lcx", "lmx";
> +
> +			memory-region = <&slpi_mem>;
> +
> +			qcom,smem-states = <&slpi_smp2p_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			status = "disabled";
> +
> +			glink-edge {
> +				interrupts = <GIC_SPI 170 IRQ_TYPE_EDGE_RISING>;
> +				label = "dsps";
> +				qcom,remote-pid = <3>;
> +				mboxes = <&apss_shared 24>;
> +			};
> +		};
> +
> +

Do not add double blank lines. Same in other patchsets.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 2f32179c7d1b..8dcfe6293762 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -3311,6 +3311,43 @@  glink-edge {
 			};
 		};
 
+		slpi_pas: remoteproc@5c00000 {
+			compatible = "qcom,sdm845-slpi-pas";
+			reg = <0 0x5c00000 0 0x4000>;
+
+			interrupts-extended = <&intc GIC_SPI 494 IRQ_TYPE_EDGE_RISING>,
+						<&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+						<&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+						<&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+						<&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+						"handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			qcom,qmp = <&aoss_qmp>;
+
+			power-domains = <&rpmhpd SDM845_CX>,
+					<&rpmhpd SDM845_MX>;
+			power-domain-names = "lcx", "lmx";
+
+			memory-region = <&slpi_mem>;
+
+			qcom,smem-states = <&slpi_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 170 IRQ_TYPE_EDGE_RISING>;
+				label = "dsps";
+				qcom,remote-pid = <3>;
+				mboxes = <&apss_shared 24>;
+			};
+		};
+
+
 		gpucc: clock-controller@5090000 {
 			compatible = "qcom,sdm845-gpucc";
 			reg = <0 0x05090000 0 0x9000>;