phy: tegra: xusb: Support sleepwalk for Tegra234
Commit Message
From: Henry Lin <henryl@nvidia.com>
Add new registers programming in sleepwalk sequence for Tegra234:
MASTER_ENABLE_A/B/C/D in XUSB_AO_UTMIP_SLEEPWALK.
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
---
drivers/phy/tegra/xusb-tegra186.c | 20 ++++++++++++++++++++
drivers/phy/tegra/xusb.h | 1 +
2 files changed, 21 insertions(+)
Comments
On 09-03-23, 14:17, Haotien Hsu wrote:
> From: Henry Lin <henryl@nvidia.com>
>
> Add new registers programming in sleepwalk sequence for Tegra234:
> MASTER_ENABLE_A/B/C/D in XUSB_AO_UTMIP_SLEEPWALK.
Applied, thanks
@@ -145,6 +145,8 @@
#define MODE_HS MODE(0)
#define MODE_RST MODE(1)
+#define XUSB_AO_UTMIP_SLEEPWALK_STATUS(x) (0xa0 + (x) * 4)
+
#define XUSB_AO_UTMIP_SLEEPWALK_CFG(x) (0xd0 + (x) * 4)
#define XUSB_AO_UHSIC_SLEEPWALK_CFG(x) (0xf0 + (x) * 4)
#define FAKE_USBOP_VAL BIT(0)
@@ -172,24 +174,30 @@
#define AP_A BIT(4)
#define AN_A BIT(5)
#define HIGHZ_A BIT(6)
+#define MASTER_ENABLE_A BIT(7)
/* phase B */
#define USBOP_RPD_B BIT(8)
#define USBON_RPD_B BIT(9)
#define AP_B BIT(12)
#define AN_B BIT(13)
#define HIGHZ_B BIT(14)
+#define MASTER_ENABLE_B BIT(15)
/* phase C */
#define USBOP_RPD_C BIT(16)
#define USBON_RPD_C BIT(17)
#define AP_C BIT(20)
#define AN_C BIT(21)
#define HIGHZ_C BIT(22)
+#define MASTER_ENABLE_C BIT(23)
/* phase D */
#define USBOP_RPD_D BIT(24)
#define USBON_RPD_D BIT(25)
#define AP_D BIT(28)
#define AN_D BIT(29)
#define HIGHZ_D BIT(30)
+#define MASTER_ENABLE_D BIT(31)
+#define MASTER_ENABLE_B_C_D \
+ (MASTER_ENABLE_B | MASTER_ENABLE_C | MASTER_ENABLE_D)
#define XUSB_AO_UHSIC_SLEEPWALK(x) (0x120 + (x) * 4)
/* phase A */
@@ -417,6 +425,8 @@ static int tegra186_utmi_enable_phy_sleepwalk(struct tegra_xusb_lane *lane,
value |= HIGHZ_A;
value |= AP_A;
value |= AN_B | AN_C | AN_D;
+ if (padctl->soc->supports_lp_cfg_en)
+ value |= MASTER_ENABLE_B_C_D;
break;
case USB_SPEED_LOW:
@@ -424,6 +434,8 @@ static int tegra186_utmi_enable_phy_sleepwalk(struct tegra_xusb_lane *lane,
value |= HIGHZ_A;
value |= AN_A;
value |= AP_B | AP_C | AP_D;
+ if (padctl->soc->supports_lp_cfg_en)
+ value |= MASTER_ENABLE_B_C_D;
break;
default:
@@ -488,6 +500,13 @@ static int tegra186_utmi_disable_phy_sleepwalk(struct tegra_xusb_lane *lane)
value |= WAKE_VAL_NONE;
ao_writel(priv, value, XUSB_AO_UTMIP_SLEEPWALK_CFG(index));
+ if (padctl->soc->supports_lp_cfg_en) {
+ /* disable the four stages of sleepwalk */
+ value = ao_readl(priv, XUSB_AO_UTMIP_SLEEPWALK(index));
+ value &= ~(MASTER_ENABLE_A | MASTER_ENABLE_B_C_D);
+ ao_writel(priv, value, XUSB_AO_UTMIP_SLEEPWALK(index));
+ }
+
/* power down the line state detectors of the port */
value = ao_readl(priv, XUSB_AO_UTMIP_PAD_CFG(index));
value |= USBOP_VAL_PD | USBON_VAL_PD;
@@ -1673,6 +1692,7 @@ const struct tegra_xusb_padctl_soc tegra234_xusb_padctl_soc = {
.supports_gen2 = true,
.poll_trk_completed = true,
.trk_hw_mode = true,
+ .supports_lp_cfg_en = true,
};
EXPORT_SYMBOL_GPL(tegra234_xusb_padctl_soc);
#endif
@@ -434,6 +434,7 @@ struct tegra_xusb_padctl_soc {
bool need_fake_usb3_port;
bool poll_trk_completed;
bool trk_hw_mode;
+ bool supports_lp_cfg_en;
};
struct tegra_xusb_padctl {