[net-next,v8.1] net: phy: Add driver for Motorcomm yt8521 gigabit ethernet phy

diff --git a/MAINTAINERS b/MAINTAINERS
index a96c60c787af..922cd832eed1 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13937,6 +13937,7 @@  F:	include/uapi/linux/meye.h
 
 MOTORCOMM PHY DRIVER
 M:	Peter Geis <pgwipeout@gmail.com>
+M:	Frank <Frank.Sae@motor-comm.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/phy/motorcomm.c
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index c57a0262fb64..040c8bf6d05b 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -260,7 +260,7 @@  config MOTORCOMM_PHY
 	tristate "Motorcomm PHYs"
 	help
 	  Enables support for Motorcomm network PHYs.
-	  Currently supports the YT8511 gigabit PHY.
+	  Currently supports the YT8511, YT8521 Gigabit Ethernet PHYs.
 
 config NATIONAL_PHY
 	tristate "National Semiconductor PHYs"
diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
index 7e6ac2c5e27e..387d54117b9e 100644
--- a/drivers/net/phy/motorcomm.c
+++ b/drivers/net/phy/motorcomm.c
@@ -1,15 +1,106 @@ 
 // SPDX-License-Identifier: GPL-2.0+
 /*
- * Driver for Motorcomm PHYs
+ * Motorcomm 8511/8521 PHY driver.
  *
  * Author: Peter Geis <pgwipeout@gmail.com>
+ * Author: Frank <Frank.Sae@motor-comm.com>
  */
 
+#include <linux/etherdevice.h>
 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/phy.h>
 
 #define PHY_ID_YT8511		0x0000010a
+#define PHY_ID_YT8521				0x0000011A
+
+/* YT8521 Register Overview
+ *	UTP Register space	|	FIBER Register space
+ *  ------------------------------------------------------------
+ * |	UTP MII			|	FIBER MII		|
+ * |	UTP MMD			|				|
+ * |	UTP Extended		|	FIBER Extended		|
+ *  ------------------------------------------------------------
+ * |			Common Extended				|
+ *  ------------------------------------------------------------
+ */
+
+/* 0x10 ~ 0x15 , 0x1E and 0x1F are common MII registers of yt phy */
+
+/* Specific Function Control Register */
+#define YTPHY_SPECIFIC_FUNCTION_CONTROL_REG	0x10
+
+/* 2b00 Manual MDI configuration
+ * 2b01 Manual MDIX configuration
+ * 2b10 Reserved
+ * 2b11 Enable automatic crossover for all modes  *default*
+ */
+#define YTPHY_SFCR_MDI_CROSSOVER_MODE_MASK	(BIT(6) | BIT(5))
+#define YTPHY_SFCR_CROSSOVER_EN			BIT(3)
+#define YTPHY_SFCR_SQE_TEST_EN			BIT(2)
+#define YTPHY_SFCR_POLARITY_REVERSAL_EN		BIT(1)
+#define YTPHY_SFCR_JABBER_DIS			BIT(0)
+
+/* Specific Status Register */
+#define YTPHY_SPECIFIC_STATUS_REG		0x11
+#define YTPHY_SSR_SPEED_MODE_OFFSET		14
+
+#define YTPHY_SSR_SPEED_MODE_MASK		(BIT(15) | BIT(14))
+#define YTPHY_SSR_SPEED_10M			0x0
+#define YTPHY_SSR_SPEED_100M			0x1
+#define YTPHY_SSR_SPEED_1000M			0x2
+#define YTPHY_SSR_DUPLEX_OFFSET			13
+#define YTPHY_SSR_DUPLEX			BIT(13)
+#define YTPHY_SSR_PAGE_RECEIVED			BIT(12)
+#define YTPHY_SSR_SPEED_DUPLEX_RESOLVED		BIT(11)
+#define YTPHY_SSR_LINK				BIT(10)
+#define YTPHY_SSR_MDIX_CROSSOVER		BIT(6)
+#define YTPHY_SSR_DOWNGRADE			BIT(5)
+#define YTPHY_SSR_TRANSMIT_PAUSE		BIT(3)
+#define YTPHY_SSR_RECEIVE_PAUSE			BIT(2)
+#define YTPHY_SSR_POLARITY			BIT(1)
+#define YTPHY_SSR_JABBER			BIT(0)
+
+/* Interrupt enable Register */
+#define YTPHY_INTERRUPT_ENABLE_REG		0x12
+#define YTPHY_IER_WOL				BIT(6)
+
+/* Interrupt Status Register */
+#define YTPHY_INTERRUPT_STATUS_REG		0x13
+#define YTPHY_ISR_AUTONEG_ERR			BIT(15)
+#define YTPHY_ISR_SPEED_CHANGED			BIT(14)
+#define YTPHY_ISR_DUPLEX_CHANGED		BIT(13)
+#define YTPHY_ISR_PAGE_RECEIVED			BIT(12)
+#define YTPHY_ISR_LINK_FAILED			BIT(11)
+#define YTPHY_ISR_LINK_SUCCESSED		BIT(10)
+#define YTPHY_ISR_WOL				BIT(6)
+#define YTPHY_ISR_WIRESPEED_DOWNGRADE		BIT(5)
+#define YTPHY_ISR_SERDES_LINK_FAILED		BIT(3)
+#define YTPHY_ISR_SERDES_LINK_SUCCESSED		BIT(2)
+#define YTPHY_ISR_POLARITY_CHANGED		BIT(1)
+#define YTPHY_ISR_JABBER_HAPPENED		BIT(0)
+
+/* Speed Auto Downgrade Control Register */
+#define YTPHY_SPEED_AUTO_DOWNGRADE_CONTROL_REG	0x14
+#define YTPHY_SADCR_SPEED_DOWNGRADE_EN		BIT(5)
+
+/* If these bits are set to 3, the PHY attempts five times ( 3(set value) +
+ * additional 2) before downgrading, default 0x3
+ */
+#define YTPHY_SADCR_SPEED_RETRY_LIMIT		(0x3 << 2)
+
+/* Rx Error Counter Register */
+#define YTPHY_RX_ERROR_COUNTER_REG		0x15
+
+/* Extended Register's Address Offset Register */
+#define YTPHY_PAGE_SELECT			0x1E
+
+/* Extended Register's Data Register */
+#define YTPHY_PAGE_DATA				0x1F
+
+/* FIBER Auto-Negotiation link partner ability */
+#define YTPHY_FLPA_PAUSE			(0x3 << 7)
+#define YTPHY_FLPA_ASYM_PAUSE			(0x2 << 7)
 
 #define YT8511_PAGE_SELECT	0x1e
 #define YT8511_PAGE		0x1f
@@ -38,6 +129,352 @@ 
 #define YT8511_DELAY_FE_TX_EN	(0xf << 12)
 #define YT8511_DELAY_FE_TX_DIS	(0x2 << 12)
 
+/* Extended register is different from MMD Register and MII Register.
+ * We can use ytphy_read_ext/ytphy_write_ext/ytphy_modify_ext function to
+ * operate extended register.
+ * Extended Register  start
+ */
+
+/* Phy gmii clock gating Register */
+#define YT8521_CLOCK_GATING_REG			0xC
+#define YT8521_CGR_RX_CLK_EN			BIT(12)
+
+#define YT8521_EXTREG_SLEEP_CONTROL1_REG	0x27
+#define YT8521_ESC1R_SLEEP_SW			BIT(15)
+#define YT8521_ESC1R_PLLON_SLP			BIT(14)
+
+/* Phy fiber Link timer cfg2 Register */
+#define YT8521_LINK_TIMER_CFG2_REG		0xA5
+#define YT8521_LTCR_EN_AUTOSEN			BIT(15)
+
+/* 0xA000, 0xA001, 0xA003 ,and 0xA006 ~ 0xA00A  are common ext registers
+ * of yt8521 phy. There is no need to switch reg space when operating these
+ * registers.
+ */
+
+#define YT8521_REG_SPACE_SELECT_REG		0xA000
+#define YT8521_RSSR_SPACE_MASK			BIT(1)
+#define YT8521_RSSR_FIBER_SPACE			(0x1 << 1)
+#define YT8521_RSSR_UTP_SPACE			(0x0 << 1)
+#define YT8521_RSSR_TO_BE_ARBITRATED		(0xFF)
+
+#define YT8521_CHIP_CONFIG_REG			0xA001
+#define YT8521_CCR_SW_RST			BIT(15)
+
+#define YT8521_CCR_MODE_SEL_MASK		(BIT(2) | BIT(1) | BIT(0))
+#define YT8521_CCR_MODE_UTP_TO_RGMII		0
+#define YT8521_CCR_MODE_FIBER_TO_RGMII		1
+#define YT8521_CCR_MODE_UTP_FIBER_TO_RGMII	2
+#define YT8521_CCR_MODE_UTP_TO_SGMII		3
+#define YT8521_CCR_MODE_SGPHY_TO_RGMAC		4
+#define YT8521_CCR_MODE_SGMAC_TO_RGPHY		5
+#define YT8521_CCR_MODE_UTP_TO_FIBER_AUTO	6
+#define YT8521_CCR_MODE_UTP_TO_FIBER_FORCE	7
+
+/* 3 phy polling modes,poll mode combines utp and fiber mode*/
+#define YT8521_MODE_FIBER			0x1
+#define YT8521_MODE_UTP				0x2
+#define YT8521_MODE_POLL			0x3
+
+#define YT8521_RGMII_CONFIG1_REG		0xA003
+
+/* TX Gig-E Delay is bits 3:0, default 0x1
+ * TX Fast-E Delay is bits 7:4, default 0xf
+ * RX Delay is bits 13:10, default 0x0
+ * Delay = 150ps * N
+ * On = 2250ps, off = 0ps
+ */
+#define YT8521_RC1R_RX_DELAY_MASK		(0xF << 10)
+#define YT8521_RC1R_RX_DELAY_EN			(0xF << 10)
+#define YT8521_RC1R_RX_DELAY_DIS		(0x0 << 10)
+#define YT8521_RC1R_FE_TX_DELAY_MASK		(0xF << 4)
+#define YT8521_RC1R_FE_TX_DELAY_EN		(0xF << 4)
+#define YT8521_RC1R_FE_TX_DELAY_DIS		(0x0 << 4)
+#define YT8521_RC1R_GE_TX_DELAY_MASK		(0xF << 0)
+#define YT8521_RC1R_GE_TX_DELAY_EN		(0xF << 0)
+#define YT8521_RC1R_GE_TX_DELAY_DIS		(0x0 << 0)
+
+#define YTPHY_MISC_CONFIG_REG			0xA006
+#define YTPHY_MCR_FIBER_SPEED_MASK		BIT(0)
+#define YTPHY_MCR_FIBER_1000BX			(0x1 << 0)
+#define YTPHY_MCR_FIBER_100FX			(0x0 << 0)
+
+/* WOL MAC ADDR: MACADDR2(highest), MACADDR1(middle), MACADDR0(lowest) */
+#define YTPHY_WOL_MACADDR2_REG			0xA007
+#define YTPHY_WOL_MACADDR1_REG			0xA008
+#define YTPHY_WOL_MACADDR0_REG			0xA009
+
+#define YTPHY_WOL_CONFIG_REG			0xA00A
+#define YTPHY_WCR_INTR_SEL			BIT(6)
+#define YTPHY_WCR_ENABLE			BIT(3)
+
+/* 2b00 84ms
+ * 2b01 168ms  *default*
+ * 2b10 336ms
+ * 2b11 672ms
+ */
+#define YTPHY_WCR_PULSE_WIDTH_MASK		(BIT(2) | BIT(1))
+#define YTPHY_WCR_PULSE_WIDTH_672MS		(BIT(2) | BIT(1))
+
+/* 1b0 Interrupt and WOL events is level triggered and active LOW  *default*
+ * 1b1 Interrupt and WOL events is pulse triggered and active LOW
+ */
+#define YTPHY_WCR_TYPE_PULSE			BIT(0)
+
+/* Extended Register  end */
+
+struct yt8521_priv {
+	/* combo_advertising is used for case of YT8521 in combo mode,
+	 * this means that yt8521 may work in utp or fiber mode which depends
+	 * on which media is connected (YT8521_RSSR_TO_BE_ARBITRATED).
+	 */
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(combo_advertising);
+
+	/* YT8521_MODE_FIBER / YT8521_MODE_UTP / YT8521_MODE_POLL*/
+	u8 polling_mode;
+	u8 strap_mode; /* 8 working modes  */
+	/* current reg page of yt8521 phy:
+	 * YT8521_RSSR_UTP_SPACE
+	 * YT8521_RSSR_FIBER_SPACE
+	 * YT8521_RSSR_TO_BE_ARBITRATED
+	 */
+	u8 reg_page;
+};
+
+/**
+ * ytphy_read_ext() - read a PHY's extended register
+ * @phydev: a pointer to a &struct phy_device
+ * @regnum: register number to read
+ *
+ * NOTE:The caller must have taken the MDIO bus lock.
+ *
+ * returns the value of regnum reg or negative error code
+ */
+static int ytphy_read_ext(struct phy_device *phydev, u16 regnum)
+{
+	int ret;
+
+	ret = __phy_write(phydev, YTPHY_PAGE_SELECT, regnum);
+	if (ret < 0)
+		return ret;
+
+	return __phy_read(phydev, YTPHY_PAGE_DATA);
+}
+
+/**
+ * ytphy_read_ext_with_lock() - read a PHY's extended register
+ * @phydev: a pointer to a &struct phy_device
+ * @regnum: register number to read
+ *
+ * returns the value of regnum reg or negative error code
+ */
+static int ytphy_read_ext_with_lock(struct phy_device *phydev, u16 regnum)
+{
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+	ret = ytphy_read_ext(phydev, regnum);
+	phy_unlock_mdio_bus(phydev);
+
+	return ret;
+}
+
+/**
+ * ytphy_write_ext() - write a PHY's extended register
+ * @phydev: a pointer to a &struct phy_device
+ * @regnum: register number to write
+ * @val: value to write to @regnum
+ *
+ * NOTE:The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative error code
+ */
+static int ytphy_write_ext(struct phy_device *phydev, u16 regnum, u16 val)
+{
+	int ret;
+
+	ret = __phy_write(phydev, YTPHY_PAGE_SELECT, regnum);
+	if (ret < 0)
+		return ret;
+
+	return __phy_write(phydev, YTPHY_PAGE_DATA, val);
+}
+
+/**
+ * ytphy_write_ext_with_lock() - write a PHY's extended register
+ * @phydev: a pointer to a &struct phy_device
+ * @regnum: register number to write
+ * @val: value to write to @regnum
+ *
+ * returns 0 or negative error code
+ */
+static int ytphy_write_ext_with_lock(struct phy_device *phydev, u16 regnum,
+				     u16 val)
+{
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+	ret = ytphy_write_ext(phydev, regnum, val);
+	phy_unlock_mdio_bus(phydev);
+
+	return ret;
+}
+
+/**
+ * ytphy_modify_ext() - bits modify a PHY's extended register
+ * @phydev: a pointer to a &struct phy_device
+ * @regnum: register number to write
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ *
+ * NOTE: Convenience function which allows a PHY's extended register to be
+ * modified as new register value = (old register value & ~mask) | set.
+ * The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative error code
+ */
+static int ytphy_modify_ext(struct phy_device *phydev, u16 regnum, u16 mask,
+			    u16 set)
+{
+	int ret;
+
+	ret = __phy_write(phydev, YTPHY_PAGE_SELECT, regnum);
+	if (ret < 0)
+		return ret;
+
+	return __phy_modify(phydev, YTPHY_PAGE_DATA, mask, set);
+}
+
+/**
+ * ytphy_modify_ext_with_lock() - bits modify a PHY's extended register
+ * @phydev: a pointer to a &struct phy_device
+ * @regnum: register number to write
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ *
+ * NOTE: Convenience function which allows a PHY's extended register to be
+ * modified as new register value = (old register value & ~mask) | set.
+ *
+ * returns 0 or negative error code
+ */
+static int ytphy_modify_ext_with_lock(struct phy_device *phydev, u16 regnum,
+				      u16 mask, u16 set)
+{
+	int ret;
+
+	phy_lock_mdio_bus(phydev);
+	ret = ytphy_modify_ext(phydev, regnum, mask, set);
+	phy_unlock_mdio_bus(phydev);
+
+	return ret;
+}
+
+/**
+ * ytphy_get_wol() - report whether wake-on-lan is enabled
+ * @phydev: a pointer to a &struct phy_device
+ * @wol: a pointer to a &struct ethtool_wolinfo
+ *
+ * NOTE: YTPHY_WOL_CONFIG_REG is common ext reg.
+ */
+static void ytphy_get_wol(struct phy_device *phydev,
+			  struct ethtool_wolinfo *wol)
+{
+	int wol_config;
+
+	wol->supported = WAKE_MAGIC;
+	wol->wolopts = 0;
+
+	wol_config = ytphy_read_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG);
+	if (wol_config < 0)
+		return;
+
+	if (wol_config & YTPHY_WCR_ENABLE)
+		wol->wolopts |= WAKE_MAGIC;
+}
+
+/**
+ * ytphy_set_wol() - turn wake-on-lan on or off
+ * @phydev: a pointer to a &struct phy_device
+ * @wol: a pointer to a &struct ethtool_wolinfo
+ *
+ * NOTE: YTPHY_WOL_CONFIG_REG, YTPHY_WOL_MACADDR2_REG, YTPHY_WOL_MACADDR1_REG
+ * and YTPHY_WOL_MACADDR0_REG are common ext reg. The
+ * YTPHY_INTERRUPT_ENABLE_REG of UTP is special, fiber also use this register.
+ *
+ * returns 0 or negative errno code
+ */
+static int ytphy_set_wol(struct phy_device *phydev, struct ethtool_wolinfo *wol)
+{
+	struct net_device *p_attached_dev;
+	const u16 mac_addr_reg[] = {
+		YTPHY_WOL_MACADDR2_REG,
+		YTPHY_WOL_MACADDR1_REG,
+		YTPHY_WOL_MACADDR0_REG,
+	};
+	const u8 *mac_addr;
+	int old_page;
+	int ret = 0;
+	u16 mask;
+	u16 val;
+	u8 i;
+
+	if (wol->wolopts & WAKE_MAGIC) {
+		p_attached_dev = phydev->attached_dev;
+		if (!p_attached_dev)
+			return -ENODEV;
+
+		mac_addr = (const u8 *)p_attached_dev->dev_addr;
+		if (!is_valid_ether_addr(mac_addr))
+			return -EINVAL;
+
+		/* lock mdio bus then switch to utp reg space */
+		old_page = phy_select_page(phydev, YT8521_RSSR_UTP_SPACE);
+		if (old_page < 0)
+			goto err_restore_page;
+
+		/* Store the device address for the magic packet */
+		for (i = 0; i < 3; i++) {
+			ret = ytphy_write_ext(phydev, mac_addr_reg[i],
+					      ((mac_addr[i * 2] << 8)) |
+						      (mac_addr[i * 2 + 1]));
+			if (ret < 0)
+				goto err_restore_page;
+		}
+
+		/* Enable WOL feature */
+		mask = YTPHY_WCR_PULSE_WIDTH_MASK | YTPHY_WCR_INTR_SEL;
+		val = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL;
+		val |= YTPHY_WCR_TYPE_PULSE | YTPHY_WCR_PULSE_WIDTH_672MS;
+		ret = ytphy_modify_ext(phydev, YTPHY_WOL_CONFIG_REG, mask, val);
+		if (ret < 0)
+			goto err_restore_page;
+
+		/* Enable WOL interrupt */
+		ret = __phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG, 0,
+				   YTPHY_IER_WOL);
+		if (ret < 0)
+			goto err_restore_page;
+
+	} else {
+		old_page = phy_select_page(phydev, YT8521_RSSR_UTP_SPACE);
+		if (old_page < 0)
+			goto err_restore_page;
+
+		/* Disable WOL feature */
+		mask = YTPHY_WCR_ENABLE | YTPHY_WCR_INTR_SEL;
+		ret = ytphy_modify_ext(phydev, YTPHY_WOL_CONFIG_REG, mask, 0);
+
+		/* Disable WOL interrupt */
+		ret = __phy_modify(phydev, YTPHY_INTERRUPT_ENABLE_REG,
+				   YTPHY_IER_WOL, 0);
+		if (ret < 0)
+			goto err_restore_page;
+	}
+
+err_restore_page:
+	return phy_restore_page(phydev, old_page, ret);
+}
+
 static int yt8511_read_page(struct phy_device *phydev)
 {
 	return __phy_read(phydev, YT8511_PAGE_SELECT);
@@ -111,6 +548,1183 @@  static int yt8511_config_init(struct phy_device *phydev)
 	return phy_restore_page(phydev, oldpage, ret);
 }
 
+/**
+ * yt8521_read_page() - read reg page
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns current reg space of yt8521 (YT8521_RSSR_FIBER_SPACE/
+ * YT8521_RSSR_UTP_SPACE) or negative errno code
+ */
+static int yt8521_read_page(struct phy_device *phydev)
+{
+	int old_page;
+
+	old_page = ytphy_read_ext(phydev, YT8521_REG_SPACE_SELECT_REG);
+	if (old_page < 0)
+		return old_page;
+
+	if ((old_page & YT8521_RSSR_SPACE_MASK) == YT8521_RSSR_FIBER_SPACE)
+		return YT8521_RSSR_FIBER_SPACE;
+
+	return YT8521_RSSR_UTP_SPACE;
+};
+
+/**
+ * yt8521_write_page() - write reg page
+ * @phydev: a pointer to a &struct phy_device
+ * @page: The reg page(YT8521_RSSR_FIBER_SPACE/YT8521_RSSR_UTP_SPACE) to write.
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_write_page(struct phy_device *phydev, int page)
+{
+	int mask = YT8521_RSSR_SPACE_MASK;
+	int set;
+
+	if ((page & YT8521_RSSR_SPACE_MASK) == YT8521_RSSR_FIBER_SPACE)
+		set = YT8521_RSSR_FIBER_SPACE;
+	else
+		set = YT8521_RSSR_UTP_SPACE;
+
+	return ytphy_modify_ext(phydev, YT8521_REG_SPACE_SELECT_REG, mask, set);
+};
+
+/**
+ * yt8521_probe() - read chip config then set suitable polling_mode
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_probe(struct phy_device *phydev)
+{
+	struct device *dev = &phydev->mdio.dev;
+	struct yt8521_priv *priv;
+	int chip_config;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	phydev->priv = priv;
+
+	chip_config = ytphy_read_ext_with_lock(phydev, YT8521_CHIP_CONFIG_REG);
+	if (chip_config < 0)
+		return chip_config;
+
+	priv->strap_mode = chip_config & YT8521_CCR_MODE_SEL_MASK;
+	switch (priv->strap_mode) {
+	case YT8521_CCR_MODE_FIBER_TO_RGMII:
+	case YT8521_CCR_MODE_SGPHY_TO_RGMAC:
+	case YT8521_CCR_MODE_SGMAC_TO_RGPHY:
+		priv->polling_mode = YT8521_MODE_FIBER;
+		priv->reg_page = YT8521_RSSR_FIBER_SPACE;
+		phydev->port = PORT_FIBRE;
+		break;
+	case YT8521_CCR_MODE_UTP_FIBER_TO_RGMII:
+	case YT8521_CCR_MODE_UTP_TO_FIBER_AUTO:
+	case YT8521_CCR_MODE_UTP_TO_FIBER_FORCE:
+		priv->polling_mode = YT8521_MODE_POLL;
+		priv->reg_page = YT8521_RSSR_TO_BE_ARBITRATED;
+		phydev->port = PORT_NONE;
+		break;
+	case YT8521_CCR_MODE_UTP_TO_SGMII:
+	case YT8521_CCR_MODE_UTP_TO_RGMII:
+		priv->polling_mode = YT8521_MODE_UTP;
+		priv->reg_page = YT8521_RSSR_UTP_SPACE;
+		phydev->port = PORT_TP;
+		break;
+	}
+	/* set default reg space */
+	if (priv->reg_page != YT8521_RSSR_TO_BE_ARBITRATED) {
+		ret = ytphy_write_ext_with_lock(phydev,
+						YT8521_REG_SPACE_SELECT_REG,
+						priv->reg_page);
+		if (ret < 0)
+			return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * ytphy_utp_read_lpa() - read LPA then setup lp_advertising for utp
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * NOTE:The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int ytphy_utp_read_lpa(struct phy_device *phydev)
+{
+	int lpa, lpagb;
+
+	if (phydev->autoneg == AUTONEG_ENABLE) {
+		if (!phydev->autoneg_complete) {
+			mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising,
+							0);
+			mii_lpa_mod_linkmode_lpa_t(phydev->lp_advertising, 0);
+			return 0;
+		}
+
+		if (phydev->is_gigabit_capable) {
+			lpagb = __phy_read(phydev, MII_STAT1000);
+			if (lpagb < 0)
+				return lpagb;
+
+			if (lpagb & LPA_1000MSFAIL) {
+				int adv = __phy_read(phydev, MII_CTRL1000);
+
+				if (adv < 0)
+					return adv;
+
+				if (adv & CTL1000_ENABLE_MASTER)
+					phydev_err(phydev, "Master/Slave resolution failed, maybe conflicting manual settings?\n");
+				else
+					phydev_err(phydev, "Master/Slave resolution failed\n");
+				return -ENOLINK;
+			}
+
+			mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising,
+							lpagb);
+		}
+
+		lpa = __phy_read(phydev, MII_LPA);
+		if (lpa < 0)
+			return lpa;
+
+		mii_lpa_mod_linkmode_lpa_t(phydev->lp_advertising, lpa);
+	} else {
+		linkmode_zero(phydev->lp_advertising);
+	}
+
+	return 0;
+}
+
+/**
+ * yt8521_adjust_status() - update speed and duplex to phydev. when in fiber
+ * mode, adjust speed and duplex.
+ * @phydev: a pointer to a &struct phy_device
+ * @status: yt8521 status read from YTPHY_SPECIFIC_STATUS_REG
+ * @is_utp: false(yt8521 work in fiber mode) or true(yt8521 work in utp mode)
+ *
+ * NOTE:The caller must have taken the MDIO bus lock.
+ *
+ * returns 0
+ */
+static int yt8521_adjust_status(struct phy_device *phydev, int status,
+				bool is_utp)
+{
+	int speed_mode, duplex;
+	int speed;
+	int err;
+	int lpa;
+
+	if (is_utp)
+		duplex = (status & YTPHY_SSR_DUPLEX) >> YTPHY_SSR_DUPLEX_OFFSET;
+	else
+		duplex = DUPLEX_FULL;	/* for fiber, it always DUPLEX_FULL */
+
+	speed_mode = (status & YTPHY_SSR_SPEED_MODE_MASK) >>
+		     YTPHY_SSR_SPEED_MODE_OFFSET;
+
+	switch (speed_mode) {
+	case YTPHY_SSR_SPEED_10M:
+		if (is_utp)
+			speed = SPEED_10;
+		else
+			/* for fiber, it will never run here, default to
+			 * SPEED_UNKNOWN
+			 */
+			speed = SPEED_UNKNOWN;
+		break;
+	case YTPHY_SSR_SPEED_100M:
+		speed = SPEED_100;
+		break;
+	case YTPHY_SSR_SPEED_1000M:
+		speed = SPEED_1000;
+		break;
+	default:
+		speed = SPEED_UNKNOWN;
+		break;
+	}
+
+	phydev->speed = speed;
+	phydev->duplex = duplex;
+
+	if (is_utp) {
+		err = ytphy_utp_read_lpa(phydev);
+		if (err < 0)
+			return err;
+
+		phy_resolve_aneg_pause(phydev);
+	} else {
+		lpa = __phy_read(phydev, MII_LPA);
+		if (lpa < 0)
+			return lpa;
+
+		/* only support 1000baseX Full */
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+				 phydev->lp_advertising, lpa & LPA_1000XFULL);
+
+		if (!(lpa & YTPHY_FLPA_PAUSE)) {
+			phydev->pause = 0;
+			phydev->asym_pause = 0;
+		} else if ((lpa & YTPHY_FLPA_ASYM_PAUSE)) {
+			phydev->pause = 1;
+			phydev->asym_pause = 1;
+		} else {
+			phydev->pause = 1;
+			phydev->asym_pause = 0;
+		}
+	}
+
+	return 0;
+}
+
+/**
+ * yt8521_read_status_paged() -  determines the speed and duplex of one page
+ * @phydev: a pointer to a &struct phy_device
+ * @page: The reg page(YT8521_RSSR_FIBER_SPACE/YT8521_RSSR_UTP_SPACE) to
+ * operate.
+ *
+ * returns 1 (utp or fiber link),0 (no link) or negative errno code
+ */
+static int yt8521_read_status_paged(struct phy_device *phydev, int page)
+{
+	int fiber_latch_val;
+	int fiber_curr_val;
+	int old_page;
+	int ret = 0;
+	int status;
+	int link;
+
+	linkmode_zero(phydev->lp_advertising);
+	phydev->duplex = DUPLEX_UNKNOWN;
+	phydev->speed = SPEED_UNKNOWN;
+	phydev->asym_pause = 0;
+	phydev->pause = 0;
+
+	/* YT8521 has two reg space (utp/fiber) for linkup with utp/fiber
+	 * respectively. but for utp/fiber combo mode, reg space should be
+	 * arbitrated based on media priority. by default, utp takes
+	 * priority. reg space should be properly set before read
+	 * YTPHY_SPECIFIC_STATUS_REG.
+	 */
+
+	page &= YT8521_RSSR_SPACE_MASK;
+	old_page = phy_select_page(phydev, page);
+	if (old_page < 0)
+		goto err_restore_page;
+
+	/* Read YTPHY_SPECIFIC_STATUS_REG, which indicates the speed and duplex
+	 * of the PHY is actually using.
+	 */
+	ret = __phy_read(phydev, YTPHY_SPECIFIC_STATUS_REG);
+	if (ret < 0)
+		goto err_restore_page;
+
+	status = ret;
+	link = !!(status & YTPHY_SSR_LINK);
+
+	/* When PHY is in fiber mode, speed transferred from 1000Mbps to
+	 * 100Mbps,there is not link down from YTPHY_SPECIFIC_STATUS_REG, so
+	 * we need check MII_BMSR to identify such case.
+	 */
+	if (page == YT8521_RSSR_FIBER_SPACE) {
+		ret = __phy_read(phydev, MII_BMSR);
+		if (ret < 0)
+			goto err_restore_page;
+
+		fiber_latch_val = ret;
+		ret = __phy_read(phydev, MII_BMSR);
+		if (ret < 0)
+			goto err_restore_page;
+
+		fiber_curr_val = ret;
+		if (link && fiber_latch_val != fiber_curr_val) {
+			link = 0;
+			phydev_info(phydev,
+				    "%s, fiber link down detect, latch = %04x, curr = %04x\n",
+				    __func__, fiber_latch_val, fiber_curr_val);
+		}
+	} else {
+		/* Read autonegotiation status */
+		ret = __phy_read(phydev, MII_BMSR);
+		if (ret < 0)
+			return ret;
+
+		phydev->autoneg_complete = ret & BMSR_ANEGCOMPLETE ? 1 : 0;
+	}
+
+	if (link) {
+		if (page == YT8521_RSSR_UTP_SPACE)
+			yt8521_adjust_status(phydev, status, true);
+		else
+			yt8521_adjust_status(phydev, status, false);
+	}
+	return phy_restore_page(phydev, old_page, link);
+
+err_restore_page:
+	return phy_restore_page(phydev, old_page, ret);
+}
+
+/**
+ * yt8521_read_status() -  determines the negotiated speed and duplex
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_read_status(struct phy_device *phydev)
+{
+	struct yt8521_priv *priv = phydev->priv;
+	int link_fiber = 0;
+	int link_utp;
+	int link;
+	int ret;
+
+	if (priv->reg_page != YT8521_RSSR_TO_BE_ARBITRATED) {
+		link = yt8521_read_status_paged(phydev, priv->reg_page);
+		if (link < 0)
+			return link;
+	} else {
+		/* when page is YT8521_RSSR_TO_BE_ARBITRATED, arbitration is
+		 * needed. by default, utp is higher priority.
+		 */
+
+		link_utp = yt8521_read_status_paged(phydev,
+						    YT8521_RSSR_UTP_SPACE);
+		if (link_utp < 0)
+			return link_utp;
+
+		if (!link_utp) {
+			link_fiber = yt8521_read_status_paged(phydev,
+							      YT8521_RSSR_FIBER_SPACE);
+			if (link_fiber < 0)
+				return link_fiber;
+		}
+
+		link = link_utp || link_fiber;
+	}
+
+	if (link) {
+		if (phydev->link == 0) {
+			/* arbitrate reg space based on linkup media type. */
+			if (priv->polling_mode == YT8521_MODE_POLL &&
+			    priv->reg_page == YT8521_RSSR_TO_BE_ARBITRATED) {
+				if (link_fiber)
+					priv->reg_page =
+						YT8521_RSSR_FIBER_SPACE;
+				else
+					priv->reg_page = YT8521_RSSR_UTP_SPACE;
+
+				ret = ytphy_write_ext_with_lock(phydev,
+								YT8521_REG_SPACE_SELECT_REG,
+								priv->reg_page);
+				if (ret < 0)
+					return ret;
+
+				phydev->port = link_fiber ? PORT_FIBRE : PORT_TP;
+
+				phydev_info(phydev, "%s, link up, media: %s\n",
+					    __func__,
+					    (phydev->port == PORT_TP) ?
+					    "UTP" : "Fiber");
+			}
+		}
+		phydev->link = 1;
+	} else {
+		if (phydev->link == 1) {
+			phydev_info(phydev, "%s, link down, media: %s\n",
+				    __func__, (phydev->port == PORT_TP) ?
+				    "UTP" : "Fiber");
+
+			/* When in YT8521_MODE_POLL mode, need prepare for next
+			 * arbitration.
+			 */
+			if (priv->polling_mode == YT8521_MODE_POLL) {
+				priv->reg_page = YT8521_RSSR_TO_BE_ARBITRATED;
+				phydev->port = PORT_NONE;
+			}
+		}
+
+		phydev->link = 0;
+	}
+
+	return 0;
+}
+
+/**
+ * yt8521_modify_bmcr_paged - bits modify a PHY's BMCR register of one page
+ * @phydev: the phy_device struct
+ * @page: The reg page(YT8521_RSSR_FIBER_SPACE/YT8521_RSSR_UTP_SPACE) to operate
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ *
+ * NOTE: Convenience function which allows a PHY's BMCR register to be
+ * modified as new register value = (old register value & ~mask) | set.
+ * YT8521 has two space (utp/fiber) and three mode (utp/fiber/poll), each space
+ * has MII_BMCR. poll mode combines utp and faber,so need do both.
+ * If it is reset, it will wait for completion.
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_modify_bmcr_paged(struct phy_device *phydev, int page,
+				    u16 mask, u16 set)
+{
+	int max_cnt = 500; /* the max wait time of reset ~ 500 ms */
+	int old_page;
+	int ret = 0;
+
+	old_page = phy_select_page(phydev, page & YT8521_RSSR_SPACE_MASK);
+	if (old_page < 0)
+		goto err_restore_page;
+
+	ret = __phy_modify(phydev, MII_BMCR, mask, set);
+	if (ret < 0)
+		goto err_restore_page;
+
+	/* If it is reset, need to wait for the reset to complete */
+	if (set == BMCR_RESET) {
+		while (max_cnt--) {
+			usleep_range(1000, 1100);
+			ret = __phy_read(phydev, MII_BMCR);
+			if (ret < 0)
+				goto err_restore_page;
+
+			if (!(ret & BMCR_RESET))
+				return phy_restore_page(phydev, old_page, 0);
+		}
+		if (max_cnt <= 0)
+			ret = -ETIMEDOUT;
+	}
+
+err_restore_page:
+	return phy_restore_page(phydev, old_page, ret);
+}
+
+/**
+ * yt8521_modify_utp_fiber_bmcr - bits modify a PHY's BMCR register
+ * @phydev: the phy_device struct
+ * @mask: bit mask of bits to clear
+ * @set: bit mask of bits to set
+ *
+ * NOTE: Convenience function which allows a PHY's BMCR register to be
+ * modified as new register value = (old register value & ~mask) | set.
+ * YT8521 has two space (utp/fiber) and three mode (utp/fiber/poll), each space
+ * has MII_BMCR. poll mode combines utp and faber,so need do both.
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_modify_utp_fiber_bmcr(struct phy_device *phydev, u16 mask,
+					u16 set)
+{
+	struct yt8521_priv *priv = phydev->priv;
+	int ret;
+
+	if (priv->reg_page != YT8521_RSSR_TO_BE_ARBITRATED) {
+		ret = yt8521_modify_bmcr_paged(phydev, priv->reg_page, mask,
+					       set);
+		if (ret < 0)
+			return ret;
+	} else {
+		ret = yt8521_modify_bmcr_paged(phydev, YT8521_RSSR_UTP_SPACE,
+					       mask, set);
+		if (ret < 0)
+			return ret;
+
+		ret = yt8521_modify_bmcr_paged(phydev, YT8521_RSSR_FIBER_SPACE,
+					       mask, set);
+		if (ret < 0)
+			return ret;
+	}
+	return 0;
+}
+
+/**
+ * yt8521_soft_reset() - called to issue a PHY software reset
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_soft_reset(struct phy_device *phydev)
+{
+	return yt8521_modify_utp_fiber_bmcr(phydev, 0, BMCR_RESET);
+}
+
+/**
+ * yt8521_suspend() - suspend the hardware
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_suspend(struct phy_device *phydev)
+{
+	int wol_config;
+
+	/* YTPHY_WOL_CONFIG_REG is common ext reg */
+	wol_config = ytphy_read_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG);
+	if (wol_config < 0)
+		return wol_config;
+
+	/* if wol enable, do nothing */
+	if (wol_config & YTPHY_WCR_ENABLE)
+		return 0;
+
+	return yt8521_modify_utp_fiber_bmcr(phydev, 0, BMCR_PDOWN);
+}
+
+/**
+ * yt8521_resume() - resume the hardware
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_resume(struct phy_device *phydev)
+{
+	int ret;
+	int wol_config;
+
+	/* disable auto sleep */
+	ret = ytphy_modify_ext_with_lock(phydev,
+					 YT8521_EXTREG_SLEEP_CONTROL1_REG,
+					 YT8521_ESC1R_SLEEP_SW, 0);
+	if (ret < 0)
+		return ret;
+
+	wol_config = ytphy_read_ext_with_lock(phydev, YTPHY_WOL_CONFIG_REG);
+	if (wol_config < 0)
+		return wol_config;
+
+	/* if wol enable, do nothing */
+	if (wol_config & YTPHY_WCR_ENABLE)
+		return 0;
+
+	return yt8521_modify_utp_fiber_bmcr(phydev, BMCR_PDOWN, 0);
+}
+
+/**
+ * yt8521_config_init() - called to initialize the PHY
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_config_init(struct phy_device *phydev)
+{
+	int old_page;
+	int ret = 0;
+	u16 val;
+
+	old_page = phy_select_page(phydev, YT8521_RSSR_UTP_SPACE);
+	if (old_page < 0)
+		goto err_restore_page;
+
+	switch (phydev->interface) {
+	case PHY_INTERFACE_MODE_RGMII:
+		val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_GE_TX_DELAY_DIS;
+		val |= YT8521_RC1R_RX_DELAY_DIS;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_GE_TX_DELAY_DIS;
+		val |= YT8521_RC1R_RX_DELAY_EN;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+		val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_GE_TX_DELAY_EN;
+		val |= YT8521_RC1R_RX_DELAY_DIS;
+		break;
+	case PHY_INTERFACE_MODE_RGMII_ID:
+		val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_GE_TX_DELAY_EN;
+		val |= YT8521_RC1R_RX_DELAY_EN;
+		break;
+	case PHY_INTERFACE_MODE_SGMII:
+		break;
+	default: /* do not support other modes */
+		ret = -EOPNOTSUPP;
+		goto err_restore_page;
+	}
+
+	/* set rgmii delay mode */
+	if (phydev->interface != PHY_INTERFACE_MODE_SGMII) {
+		ret = ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG,
+				       (YT8521_RC1R_RX_DELAY_MASK |
+				       YT8521_RC1R_FE_TX_DELAY_MASK |
+				       YT8521_RC1R_GE_TX_DELAY_MASK),
+				       val);
+		if (ret < 0)
+			goto err_restore_page;
+	}
+
+	/* disable auto sleep */
+	ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG,
+			       YT8521_ESC1R_SLEEP_SW, 0);
+	if (ret < 0)
+		goto err_restore_page;
+
+	/* enable RXC clock when no wire plug */
+	ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG,
+			       YT8521_CGR_RX_CLK_EN, 0);
+	if (ret < 0)
+		goto err_restore_page;
+
+err_restore_page:
+	return phy_restore_page(phydev, old_page, ret);
+}
+
+/**
+ * yt8521_prepare_fiber_features() -  A small helper function that setup
+ * fiber's features.
+ * @phydev: a pointer to a &struct phy_device
+ * @dst: a pointer to store fiber's features
+ */
+static void yt8521_prepare_fiber_features(struct phy_device *phydev,
+					  unsigned long *dst)
+{
+	linkmode_set_bit(ETHTOOL_LINK_MODE_100baseFX_Full_BIT, dst);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT, dst);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, dst);
+	linkmode_set_bit(ETHTOOL_LINK_MODE_FIBRE_BIT, dst);
+}
+
+/**
+ * yt8521_fiber_setup_forced - configures/forces speed from @phydev
+ * @phydev: target phy_device struct
+ *
+ * NOTE:The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_fiber_setup_forced(struct phy_device *phydev)
+{
+	u16 val;
+	int ret;
+
+	if (phydev->speed == SPEED_1000)
+		val = YTPHY_MCR_FIBER_1000BX;
+	else if (phydev->speed == SPEED_100)
+		val = YTPHY_MCR_FIBER_100FX;
+	else
+		return -EINVAL;
+
+	ret =  __phy_modify(phydev, MII_BMCR, BMCR_ANENABLE, 0);
+	if (ret < 0)
+		return ret;
+
+	/* disable Fiber auto sensing */
+	ret =  ytphy_modify_ext(phydev, YT8521_LINK_TIMER_CFG2_REG,
+				YT8521_LTCR_EN_AUTOSEN, 0);
+	if (ret < 0)
+		return ret;
+
+	ret =  ytphy_modify_ext(phydev, YTPHY_MISC_CONFIG_REG,
+				YTPHY_MCR_FIBER_SPEED_MASK, val);
+	if (ret < 0)
+		return ret;
+
+	return ytphy_modify_ext(phydev, YT8521_CHIP_CONFIG_REG,
+				YT8521_CCR_SW_RST, 0);
+}
+
+/**
+ * ytphy_check_and_restart_aneg - Enable and restart auto-negotiation
+ * @phydev: target phy_device struct
+ * @restart: whether aneg restart is requested
+ *
+ * NOTE:The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int ytphy_check_and_restart_aneg(struct phy_device *phydev, bool restart)
+{
+	int ret;
+
+	if (!restart) {
+		/* Advertisement hasn't changed, but maybe aneg was never on to
+		 * begin with?  Or maybe phy was isolated?
+		 */
+		ret = __phy_read(phydev, MII_BMCR);
+		if (ret < 0)
+			return ret;
+
+		if (!(ret & BMCR_ANENABLE) || (ret & BMCR_ISOLATE))
+			restart = true;
+	}
+	/* Enable and Restart Autonegotiation
+	 * Don't isolate the PHY if we're negotiating
+	 */
+	if (restart)
+		return __phy_modify(phydev, MII_BMCR, BMCR_ISOLATE,
+				    BMCR_ANENABLE | BMCR_ANRESTART);
+
+	return 0;
+}
+
+/**
+ * yt8521_fiber_config_aneg - restart auto-negotiation or write
+ * YTPHY_MISC_CONFIG_REG.
+ * @phydev: target phy_device struct
+ *
+ * NOTE:The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_fiber_config_aneg(struct phy_device *phydev)
+{
+	int err, changed = 0;
+	int bmcr;
+	u16 adv;
+
+	if (phydev->autoneg != AUTONEG_ENABLE)
+		return yt8521_fiber_setup_forced(phydev);
+
+	/* enable Fiber auto sensing */
+	err =  ytphy_modify_ext(phydev, YT8521_LINK_TIMER_CFG2_REG,
+				0, YT8521_LTCR_EN_AUTOSEN);
+	if (err < 0)
+		return err;
+
+	err =  ytphy_modify_ext(phydev, YT8521_CHIP_CONFIG_REG,
+				YT8521_CCR_SW_RST, 0);
+	if (err < 0)
+		return err;
+
+	bmcr = __phy_read(phydev, MII_BMCR);
+	if (bmcr < 0)
+		return bmcr;
+
+	/* When it is coming from fiber forced mode, add bmcr power down
+	 * and power up to let aneg work fine.
+	 */
+	if (!(bmcr & BMCR_ANENABLE)) {
+		__phy_modify(phydev, MII_BMCR, 0, BMCR_PDOWN);
+		usleep_range(1000, 1100);
+		__phy_modify(phydev, MII_BMCR, BMCR_PDOWN, 0);
+	}
+
+	adv = linkmode_adv_to_mii_adv_x(phydev->advertising,
+					ETHTOOL_LINK_MODE_1000baseX_Full_BIT);
+
+	/* Setup fiber advertisement */
+	err = __phy_modify_changed(phydev, MII_ADVERTISE,
+				   ADVERTISE_1000XHALF | ADVERTISE_1000XFULL |
+				   ADVERTISE_1000XPAUSE |
+				   ADVERTISE_1000XPSE_ASYM,
+				   adv);
+	if (err < 0)
+		return err;
+
+	if (err > 0)
+		changed = 1;
+
+	return ytphy_check_and_restart_aneg(phydev, changed);
+}
+
+/**
+ * ytphy_setup_master_slave
+ * @phydev: target phy_device struct
+ *
+ * NOTE: The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int ytphy_setup_master_slave(struct phy_device *phydev)
+{
+	u16 ctl = 0;
+
+	if (!phydev->is_gigabit_capable)
+		return 0;
+
+	switch (phydev->master_slave_set) {
+	case MASTER_SLAVE_CFG_MASTER_PREFERRED:
+		ctl |= CTL1000_PREFER_MASTER;
+		break;
+	case MASTER_SLAVE_CFG_SLAVE_PREFERRED:
+		break;
+	case MASTER_SLAVE_CFG_MASTER_FORCE:
+		ctl |= CTL1000_AS_MASTER;
+		fallthrough;
+	case MASTER_SLAVE_CFG_SLAVE_FORCE:
+		ctl |= CTL1000_ENABLE_MASTER;
+		break;
+	case MASTER_SLAVE_CFG_UNKNOWN:
+	case MASTER_SLAVE_CFG_UNSUPPORTED:
+		return 0;
+	default:
+		phydev_warn(phydev, "Unsupported Master/Slave mode\n");
+		return -EOPNOTSUPP;
+	}
+
+	return __phy_modify_changed(phydev, MII_CTRL1000,
+				    (CTL1000_ENABLE_MASTER | CTL1000_AS_MASTER |
+				    CTL1000_PREFER_MASTER), ctl);
+}
+
+/**
+ * ytphy_utp_config_advert - sanitize and advertise auto-negotiation parameters
+ * @phydev: target phy_device struct
+ *
+ * NOTE: Writes MII_ADVERTISE with the appropriate values,
+ * after sanitizing the values to make sure we only advertise
+ * what is supported.  Returns < 0 on error, 0 if the PHY's advertisement
+ * hasn't changed, and > 0 if it has changed.
+ * The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int ytphy_utp_config_advert(struct phy_device *phydev)
+{
+	int err, bmsr, changed = 0;
+	u32 adv;
+
+	/* Only allow advertising what this PHY supports */
+	linkmode_and(phydev->advertising, phydev->advertising,
+		     phydev->supported);
+
+	adv = linkmode_adv_to_mii_adv_t(phydev->advertising);
+
+	/* Setup standard advertisement */
+	err = __phy_modify_changed(phydev, MII_ADVERTISE,
+				   ADVERTISE_ALL | ADVERTISE_100BASE4 |
+				   ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM,
+				   adv);
+	if (err < 0)
+		return err;
+	if (err > 0)
+		changed = 1;
+
+	bmsr = __phy_read(phydev, MII_BMSR);
+	if (bmsr < 0)
+		return bmsr;
+
+	/* Per 802.3-2008, Section 22.2.4.2.16 Extended status all
+	 * 1000Mbits/sec capable PHYs shall have the BMSR_ESTATEN bit set to a
+	 * logical 1.
+	 */
+	if (!(bmsr & BMSR_ESTATEN))
+		return changed;
+
+	adv = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising);
+
+	err = __phy_modify_changed(phydev, MII_CTRL1000,
+				   ADVERTISE_1000FULL | ADVERTISE_1000HALF,
+				   adv);
+	if (err < 0)
+		return err;
+	if (err > 0)
+		changed = 1;
+
+	return changed;
+}
+
+/**
+ * ytphy_utp_config_aneg - restart auto-negotiation or write BMCR
+ * @phydev: target phy_device struct
+ * @changed: whether autoneg is requested
+ *
+ * NOTE: If auto-negotiation is enabled, we configure the
+ * advertising, and then restart auto-negotiation.  If it is not
+ * enabled, then we write the BMCR.
+ * The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int ytphy_utp_config_aneg(struct phy_device *phydev, bool changed)
+{
+	int err;
+	u16 ctl;
+
+	err = ytphy_setup_master_slave(phydev);
+	if (err < 0)
+		return err;
+	else if (err)
+		changed = true;
+
+	if (phydev->autoneg != AUTONEG_ENABLE) {
+		/* configures/forces speed/duplex from @phydev */
+
+		ctl = mii_bmcr_encode_fixed(phydev->speed, phydev->duplex);
+
+		return __phy_modify(phydev, MII_BMCR, ~(BMCR_LOOPBACK |
+				    BMCR_ISOLATE | BMCR_PDOWN), ctl);
+	}
+
+	err = ytphy_utp_config_advert(phydev);
+	if (err < 0) /* error */
+		return err;
+	else if (err)
+		changed = true;
+
+	return ytphy_check_and_restart_aneg(phydev, changed);
+}
+
+/**
+ * yt8521_config_aneg_paged() - switch reg space then call genphy_config_aneg
+ * of one page
+ * @phydev: a pointer to a &struct phy_device
+ * @page: The reg page(YT8521_RSSR_FIBER_SPACE/YT8521_RSSR_UTP_SPACE) to
+ * operate.
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_config_aneg_paged(struct phy_device *phydev, int page)
+{
+	__ETHTOOL_DECLARE_LINK_MODE_MASK(fiber_supported);
+	struct yt8521_priv *priv = phydev->priv;
+	int old_page;
+	int ret = 0;
+
+	page &= YT8521_RSSR_SPACE_MASK;
+
+	old_page = phy_select_page(phydev, page);
+	if (old_page < 0)
+		goto err_restore_page;
+
+	/* If reg_page is YT8521_RSSR_TO_BE_ARBITRATED,
+	 * phydev->advertising should be updated.
+	 */
+	if (priv->reg_page == YT8521_RSSR_TO_BE_ARBITRATED) {
+		linkmode_zero(fiber_supported);
+		yt8521_prepare_fiber_features(phydev, fiber_supported);
+
+		/* prepare fiber_supported, then setup advertising. */
+		if (page == YT8521_RSSR_FIBER_SPACE) {
+			linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+					 fiber_supported);
+			linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+					 fiber_supported);
+			linkmode_and(phydev->advertising,
+				     priv->combo_advertising, fiber_supported);
+		} else {
+			/* ETHTOOL_LINK_MODE_Autoneg_BIT is also used in utp */
+			linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
+					   fiber_supported);
+			linkmode_andnot(phydev->advertising,
+					priv->combo_advertising,
+					fiber_supported);
+		}
+	}
+
+	if (page == YT8521_RSSR_FIBER_SPACE)
+		ret = yt8521_fiber_config_aneg(phydev);
+	else
+		ret = ytphy_utp_config_aneg(phydev, false);
+
+err_restore_page:
+	return phy_restore_page(phydev, old_page, ret);
+}
+
+/**
+ * yt8521_config_aneg() - change reg space then call yt8521_config_aneg_paged
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_config_aneg(struct phy_device *phydev)
+{
+	struct yt8521_priv *priv = phydev->priv;
+	int ret;
+
+	if (priv->reg_page != YT8521_RSSR_TO_BE_ARBITRATED) {
+		ret = yt8521_config_aneg_paged(phydev, priv->reg_page);
+		if (ret < 0)
+			return ret;
+	} else {
+		/* If reg_page is YT8521_RSSR_TO_BE_ARBITRATED,
+		 * phydev->advertising need to be saved at first run.
+		 * Because it contains the advertising which supported by both
+		 * mac and yt8521(utp and fiber).
+		 */
+		if (linkmode_empty(priv->combo_advertising)) {
+			linkmode_copy(priv->combo_advertising,
+				      phydev->advertising);
+		}
+
+		ret = yt8521_config_aneg_paged(phydev, YT8521_RSSR_UTP_SPACE);
+		if (ret < 0)
+			return ret;
+
+		ret = yt8521_config_aneg_paged(phydev, YT8521_RSSR_FIBER_SPACE);
+		if (ret < 0)
+			return ret;
+
+		/* we don't known which will be link, so restore
+		 * phydev->advertising as default value.
+		 */
+		linkmode_copy(phydev->advertising, priv->combo_advertising);
+	}
+	return 0;
+}
+
+/**
+ * yt8521_aneg_done_paged() - determines the auto negotiation result of one
+ * page.
+ * @phydev: a pointer to a &struct phy_device
+ * @page: The reg page(YT8521_RSSR_FIBER_SPACE/YT8521_RSSR_UTP_SPACE) to
+ * operate.
+ *
+ * returns 0(no link)or 1(fiber or utp link) or negative errno code
+ */
+static int yt8521_aneg_done_paged(struct phy_device *phydev, int page)
+{
+	int old_page;
+	int ret = 0;
+	int link;
+
+	old_page = phy_select_page(phydev, page & YT8521_RSSR_SPACE_MASK);
+	if (old_page < 0)
+		goto err_restore_page;
+
+	ret = __phy_read(phydev, YTPHY_SPECIFIC_STATUS_REG);
+	if (ret < 0)
+		goto err_restore_page;
+
+	link = !!(ret & YTPHY_SSR_LINK);
+	ret = link;
+
+err_restore_page:
+	return phy_restore_page(phydev, old_page, ret);
+}
+
+/**
+ * yt8521_aneg_done() - determines the auto negotiation result
+ * @phydev: a pointer to a &struct phy_device
+ *
+ * returns 0(no link)or 1(fiber or utp link) or negative errno code
+ */
+static int yt8521_aneg_done(struct phy_device *phydev)
+{
+	struct yt8521_priv *priv = phydev->priv;
+	int link_fiber = 0;
+	int link_utp;
+	int link;
+
+	if (priv->reg_page != YT8521_RSSR_TO_BE_ARBITRATED) {
+		link = yt8521_aneg_done_paged(phydev, priv->reg_page);
+	} else {
+		link_utp = yt8521_aneg_done_paged(phydev,
+						  YT8521_RSSR_UTP_SPACE);
+		if (link_utp < 0)
+			return link_utp;
+
+		if (!link_utp) {
+			link_fiber = yt8521_aneg_done_paged(phydev,
+							    YT8521_RSSR_FIBER_SPACE);
+			if (link_fiber < 0)
+				return link_fiber;
+		}
+		link = link_fiber || link_utp;
+		phydev_info(phydev, "%s, link_fiber: %d, link_utp: %d\n",
+			    __func__, link_fiber, link_utp);
+	}
+
+	return link;
+}
+
+/**
+ * ytphy_utp_read_abilities - read PHY abilities from Clause 22 registers
+ * @phydev: target phy_device struct
+ *
+ * NOTE: Reads the PHY's abilities and populates
+ * phydev->supported accordingly.
+ * The caller must have taken the MDIO bus lock.
+ *
+ * returns 0 or negative errno code
+ */
+static int ytphy_utp_read_abilities(struct phy_device *phydev)
+{
+	int val;
+
+	linkmode_set_bit_array(phy_basic_ports_array,
+			       ARRAY_SIZE(phy_basic_ports_array),
+			       phydev->supported);
+
+	val = __phy_read(phydev, MII_BMSR);
+	if (val < 0)
+		return val;
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, phydev->supported,
+			 val & BMSR_ANEGCAPABLE);
+
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, phydev->supported,
+			 val & BMSR_100FULL);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_100baseT_Half_BIT, phydev->supported,
+			 val & BMSR_100HALF);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, phydev->supported,
+			 val & BMSR_10FULL);
+	linkmode_mod_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, phydev->supported,
+			 val & BMSR_10HALF);
+
+	if (val & BMSR_ESTATEN) {
+		val = __phy_read(phydev, MII_ESTATUS);
+		if (val < 0)
+			return val;
+
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT,
+				 phydev->supported, val & ESTATUS_1000_TFULL);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT,
+				 phydev->supported, val & ESTATUS_1000_THALF);
+		linkmode_mod_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+				 phydev->supported, val & ESTATUS_1000_XFULL);
+	}
+
+	return 0;
+}
+
+/**
+ * yt8521_get_features_paged() -  read supported link modes for one page
+ * @phydev: a pointer to a &struct phy_device
+ * @page: The reg page(YT8521_RSSR_FIBER_SPACE/YT8521_RSSR_UTP_SPACE) to
+ * operate.
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_get_features_paged(struct phy_device *phydev, int page)
+{
+	int old_page;
+	int ret = 0;
+
+	page &= YT8521_RSSR_SPACE_MASK;
+	old_page = phy_select_page(phydev, page);
+	if (old_page < 0)
+		goto err_restore_page;
+
+	if (page == YT8521_RSSR_FIBER_SPACE) {
+		linkmode_zero(phydev->supported);
+		yt8521_prepare_fiber_features(phydev, phydev->supported);
+	} else {
+		ret = ytphy_utp_read_abilities(phydev);
+		if (ret < 0)
+			goto err_restore_page;
+	}
+
+err_restore_page:
+	return phy_restore_page(phydev, old_page, ret);
+}
+
+/**
+ * yt8521_get_features - switch reg space then call yt8521_get_features_paged
+ * @phydev: target phy_device struct
+ *
+ * returns 0 or negative errno code
+ */
+static int yt8521_get_features(struct phy_device *phydev)
+{
+	struct yt8521_priv *priv = phydev->priv;
+	int ret;
+
+	if (priv->reg_page != YT8521_RSSR_TO_BE_ARBITRATED) {
+		ret = yt8521_get_features_paged(phydev, priv->reg_page);
+	} else {
+		ret = yt8521_get_features_paged(phydev,
+						YT8521_RSSR_UTP_SPACE);
+		if (ret < 0)
+			return ret;
+
+		/* add fiber's features to phydev->supported */
+		yt8521_prepare_fiber_features(phydev, phydev->supported);
+	}
+	return ret;
+}
+
 static struct phy_driver motorcomm_phy_drvs[] = {
 	{
 		PHY_ID_MATCH_EXACT(PHY_ID_YT8511),
@@ -121,16 +1735,35 @@  static struct phy_driver motorcomm_phy_drvs[] = {
 		.read_page	= yt8511_read_page,
 		.write_page	= yt8511_write_page,
 	},
+	{
+		PHY_ID_MATCH_EXACT(PHY_ID_YT8521),
+		.name		= "YT8521 Gigabit Ethernet",
+		.get_features	= yt8521_get_features,
+		.probe		= yt8521_probe,
+		.read_page	= yt8521_read_page,
+		.write_page	= yt8521_write_page,
+		.get_wol	= ytphy_get_wol,
+		.set_wol	= ytphy_set_wol,
+		.config_aneg	= yt8521_config_aneg,
+		.aneg_done	= yt8521_aneg_done,
+		.config_init	= yt8521_config_init,
+		.read_status	= yt8521_read_status,
+		.soft_reset	= yt8521_soft_reset,
+		.suspend	= yt8521_suspend,
+		.resume		= yt8521_resume,
+	},
 };
 
 module_phy_driver(motorcomm_phy_drvs);
 
-MODULE_DESCRIPTION("Motorcomm PHY driver");
+MODULE_DESCRIPTION("Motorcomm 8511/8521 PHY driver");
 MODULE_AUTHOR("Peter Geis");
+MODULE_AUTHOR("Frank");
 MODULE_LICENSE("GPL");
 
 static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = {
 	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8511) },
+	{ PHY_ID_MATCH_EXACT(PHY_ID_YT8521) },
 	{ /* sentinal */ }
 };