[v7,1/4] arm64: dts: qcom: sc8280xp: Define some of the display blocks
Commit Message
From: Bjorn Andersson <bjorn.andersson@linaro.org>
Define the display clock controllers, the MDSS instances, the DP phys
and connect these together.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
---
Changes since v6:
- Dropped assigned-clock-rate on MDP_CLK
- Rearranged the properties in all nodes
arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 811 +++++++++++++++++++++++++
1 file changed, 811 insertions(+)
Comments
On 11.01.2023 04:59, Bjorn Andersson wrote:
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
>
> Define the display clock controllers, the MDSS instances, the DP phys
> and connect these together.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Konrad
>
> Changes since v6:
> - Dropped assigned-clock-rate on MDP_CLK
> - Rearranged the properties in all nodes
>
> arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 811 +++++++++++++++++++++++++
> 1 file changed, 811 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> index 0ea2f19d471b..2ed17baf50d3 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> @@ -4,6 +4,7 @@
> * Copyright (c) 2022, Linaro Limited
> */
>
> +#include <dt-bindings/clock/qcom,dispcc-sc8280xp.h>
> #include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
> #include <dt-bindings/clock/qcom,rpmh.h>
> #include <dt-bindings/interconnect/qcom,osm-l3.h>
> @@ -2097,6 +2098,42 @@ usb_1_qmpphy: phy@8903000 {
> status = "disabled";
> };
>
> + mdss1_dp0_phy: phy@8909a00 {
> + compatible = "qcom,sc8280xp-dp-phy";
> + reg = <0 0x08909a00 0 0x19c>,
> + <0 0x08909200 0 0xec>,
> + <0 0x08909600 0 0xec>,
> + <0 0x08909000 0 0x1c8>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_DPTX0_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
> + clock-names = "aux", "cfg_ahb";
> + power-domains = <&rpmhpd SC8280XP_MX>;
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + mdss1_dp1_phy: phy@890ca00 {
> + compatible = "qcom,sc8280xp-dp-phy";
> + reg = <0 0x0890ca00 0 0x19c>,
> + <0 0x0890c200 0 0xec>,
> + <0 0x0890c600 0 0xec>,
> + <0 0x0890c000 0 0x1c8>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_DPTX1_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
> + clock-names = "aux", "cfg_ahb";
> + power-domains = <&rpmhpd SC8280XP_MX>;
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> pmu@9091000 {
> compatible = "qcom,sc8280xp-llcc-bwmon", "qcom,sc7280-llcc-bwmon";
> reg = <0 0x9091000 0 0x1000>;
> @@ -2303,6 +2340,314 @@ usb_1_dwc3: usb@a800000 {
> };
> };
>
> + mdss0: display-subsystem@ae00000 {
> + compatible = "qcom,sc8280xp-mdss";
> + reg = <0 0x0ae00000 0 0x1000>;
> + reg-names = "mdss";
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_MDP_CLK>;
> + clock-names = "iface",
> + "ahb",
> + "core";
> + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> + interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
> + <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "mdp0-mem", "mdp1-mem";
> + iommus = <&apps_smmu 0x1000 0x402>;
> + power-domains = <&dispcc0 MDSS_GDSC>;
> + resets = <&dispcc0 DISP_CC_MDSS_CORE_BCR>;
> +
> + interrupt-controller;
> + #interrupt-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + status = "disabled";
> +
> + mdss0_mdp: display-controller@ae01000 {
> + compatible = "qcom,sc8280xp-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc0 DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus",
> + "nrt_bus",
> + "iface",
> + "lut",
> + "core",
> + "vsync";
> + interrupt-parent = <&mdss0>;
> + interrupts = <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <19200000>;
> + operating-points-v2 = <&mdss0_mdp_opp_table>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@5 {
> + reg = <5>;
> + mdss0_intf5_out: endpoint {
> + remote-endpoint = <&mdss0_dp3_in>;
> + };
> + };
> +
> + port@6 {
> + reg = <6>;
> + mdss0_intf6_out: endpoint {
> + remote-endpoint = <&mdss0_dp2_in>;
> + };
> + };
> + };
> +
> + mdss0_mdp_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-200000000 {
> + opp-hz = /bits/ 64 <200000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-300000000 {
> + opp-hz = /bits/ 64 <300000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-375000000 {
> + opp-hz = /bits/ 64 <375000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-500000000 {
> + opp-hz = /bits/ 64 <500000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + opp-600000000 {
> + opp-hz = /bits/ 64 <600000000>;
> + required-opps = <&rpmhpd_opp_turbo_l1>;
> + };
> + };
> + };
> +
> + mdss0_dp2: displayport-controller@ae9a000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0xae9a000 0 0x200>,
> + <0 0xae9a200 0 0x200>,
> + <0 0xae9a400 0 0x600>,
> + <0 0xae9b000 0 0x400>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss0>;
> + interrupts = <14>;
> + phys = <&mdss0_dp2_phy>;
> + phy-names = "dp";
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss0_dp2_phy 0>, <&mdss0_dp2_phy 1>;
> + operating-points-v2 = <&mdss0_dp2_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss0_dp2_in: endpoint {
> + remote-endpoint = <&mdss0_intf6_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> +
> + mdss0_dp2_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> +
> + mdss0_dp3: displayport-controller@aea0000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0xaea0000 0 0x200>,
> + <0 0xaea0200 0 0x200>,
> + <0 0xaea0400 0 0x600>,
> + <0 0xaea1000 0 0x400>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss0>;
> + interrupts = <15>;
> + phys = <&mdss0_dp3_phy>;
> + phy-names = "dp";
> + power-domains = <&dispcc0 MDSS_GDSC>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss0_dp3_phy 0>, <&mdss0_dp3_phy 1>;
> + operating-points-v2 = <&mdss0_dp3_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss0_dp3_in: endpoint {
> + remote-endpoint = <&mdss0_intf5_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> +
> + mdss0_dp3_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> + };
> +
> + mdss0_dp2_phy: phy@aec2a00 {
> + compatible = "qcom,sc8280xp-dp-phy";
> + reg = <0 0x0aec2a00 0 0x19c>,
> + <0 0x0aec2200 0 0xec>,
> + <0 0x0aec2600 0 0xec>,
> + <0 0x0aec2000 0 0x1c8>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_AHB_CLK>;
> + clock-names = "aux", "cfg_ahb";
> + power-domains = <&rpmhpd SC8280XP_MX>;
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + mdss0_dp3_phy: phy@aec5a00 {
> + compatible = "qcom,sc8280xp-dp-phy";
> + reg = <0 0x0aec5a00 0 0x19c>,
> + <0 0x0aec5200 0 0xec>,
> + <0 0x0aec5600 0 0xec>,
> + <0 0x0aec5000 0 0x1c8>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_AHB_CLK>;
> + clock-names = "aux", "cfg_ahb";
> + power-domains = <&rpmhpd SC8280XP_MX>;
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + dispcc0: clock-controller@af00000 {
> + compatible = "qcom,sc8280xp-dispcc0";
> + reg = <0 0x0af00000 0 0x20000>;
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>,
> + <&sleep_clk>,
> + <0>,
> + <0>,
> + <0>,
> + <0>,
> + <&mdss0_dp2_phy 0>,
> + <&mdss0_dp2_phy 1>,
> + <&mdss0_dp3_phy 0>,
> + <&mdss0_dp3_phy 1>,
> + <0>,
> + <0>,
> + <0>,
> + <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + #clock-cells = <1>;
> + #power-domain-cells = <1>;
> + #reset-cells = <1>;
> +
> + status = "disabled";
> + };
> +
> pdc: interrupt-controller@b220000 {
> compatible = "qcom,sc8280xp-pdc", "qcom,pdc";
> reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
> @@ -2925,6 +3270,472 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
> qcom,remote-pid = <12>;
> };
> };
> +
> + mdss1: display-subsystem@22000000 {
> + compatible = "qcom,sc8280xp-mdss";
> + reg = <0 0x22000000 0 0x1000>;
> + reg-names = "mdss";
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_CLK>;
> + clock-names = "iface",
> + "ahb",
> + "core";
> + interconnects = <&mmss_noc MASTER_MDP_CORE1_0 0 &mc_virt SLAVE_EBI1 0>,
> + <&mmss_noc MASTER_MDP_CORE1_1 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "mdp0-mem", "mdp1-mem";
> + interrupts = <GIC_SPI 865 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
> +
> + iommus = <&apps_smmu 0x1800 0x402>;
> + power-domains = <&dispcc1 MDSS_GDSC>;
> + resets = <&dispcc1 DISP_CC_MDSS_CORE_BCR>;
> +
> + #interrupt-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + status = "disabled";
> +
> + mdss1_mdp: display-controller@22001000 {
> + compatible = "qcom,sc8280xp-dpu";
> + reg = <0 0x22001000 0 0x8f000>,
> + <0 0x220b0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus",
> + "nrt_bus",
> + "iface",
> + "lut",
> + "core",
> + "vsync";
> + interrupt-parent = <&mdss1>;
> + interrupts = <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <19200000>;
> + operating-points-v2 = <&mdss1_mdp_opp_table>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss1_intf0_out: endpoint {
> + remote-endpoint = <&mdss1_dp0_in>;
> + };
> + };
> +
> + port@4 {
> + reg = <4>;
> + mdss1_intf4_out: endpoint {
> + remote-endpoint = <&mdss1_dp1_in>;
> + };
> + };
> +
> + port@5 {
> + reg = <5>;
> + mdss1_intf5_out: endpoint {
> + remote-endpoint = <&mdss1_dp3_in>;
> + };
> + };
> +
> + port@6 {
> + reg = <6>;
> + mdss1_intf6_out: endpoint {
> + remote-endpoint = <&mdss1_dp2_in>;
> + };
> + };
> + };
> +
> + mdss1_mdp_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-200000000 {
> + opp-hz = /bits/ 64 <200000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-300000000 {
> + opp-hz = /bits/ 64 <300000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-375000000 {
> + opp-hz = /bits/ 64 <375000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-500000000 {
> + opp-hz = /bits/ 64 <500000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + opp-600000000 {
> + opp-hz = /bits/ 64 <600000000>;
> + required-opps = <&rpmhpd_opp_turbo_l1>;
> + };
> + };
> + };
> +
> + mdss1_dp0: displayport-controller@22090000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0x22090000 0 0x200>,
> + <0 0x22090200 0 0x200>,
> + <0 0x22090400 0 0x600>,
> + <0 0x22091000 0 0x400>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX0_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss1>;
> + interrupts = <12>;
> + phys = <&mdss1_dp0_phy>;
> + phy-names = "dp";
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
> + <&dispcc1 DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss1_dp0_phy 0>, <&mdss1_dp0_phy 1>;
> + operating-points-v2 = <&mdss1_dp0_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss1_dp0_in: endpoint {
> + remote-endpoint = <&mdss1_intf0_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> +
> + mdss1_dp0_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> +
> + };
> +
> + mdss1_dp1: displayport-controller@22098000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0x22098000 0 0x200>,
> + <0 0x22098200 0 0x200>,
> + <0 0x22098400 0 0x600>,
> + <0 0x22099000 0 0x400>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX1_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX1_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss1>;
> + interrupts = <13>;
> + phys = <&mdss1_dp1_phy>;
> + phy-names = "dp";
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>,
> + <&dispcc1 DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss1_dp1_phy 0>, <&mdss1_dp1_phy 1>;
> + operating-points-v2 = <&mdss1_dp1_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss1_dp1_in: endpoint {
> + remote-endpoint = <&mdss1_intf4_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> +
> + mdss1_dp1_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> +
> + mdss1_dp2: displayport-controller@2209a000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0x2209a000 0 0x200>,
> + <0 0x2209a200 0 0x200>,
> + <0 0x2209a400 0 0x600>,
> + <0 0x2209b000 0 0x400>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX2_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss1>;
> + interrupts = <14>;
> + phys = <&mdss1_dp2_phy>;
> + phy-names = "dp";
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
> + <&dispcc1 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss1_dp2_phy 0>, <&mdss1_dp2_phy 1>;
> + operating-points-v2 = <&mdss1_dp2_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss1_dp2_in: endpoint {
> + remote-endpoint = <&mdss1_intf6_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> +
> + mdss1_dp2_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> +
> + mdss1_dp3: displayport-controller@220a0000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0x220a0000 0 0x200>,
> + <0 0x220a0200 0 0x200>,
> + <0 0x220a0400 0 0x600>,
> + <0 0x220a1000 0 0x400>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX3_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
> + <&dispcc1 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss1>;
> + interrupts = <15>;
> + phys = <&mdss1_dp3_phy>;
> + phy-names = "dp";
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
> + <&dispcc1 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss1_dp3_phy 0>, <&mdss1_dp3_phy 1>;
> + operating-points-v2 = <&mdss1_dp3_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> + mdss1_dp3_in: endpoint {
> + remote-endpoint = <&mdss1_intf5_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> +
> + mdss1_dp3_opp_table: opp-table {
> + compatible = "operating-points-v2";
> +
> + opp-160000000 {
> + opp-hz = /bits/ 64 <160000000>;
> + required-opps = <&rpmhpd_opp_low_svs>;
> + };
> +
> + opp-270000000 {
> + opp-hz = /bits/ 64 <270000000>;
> + required-opps = <&rpmhpd_opp_svs>;
> + };
> +
> + opp-540000000 {
> + opp-hz = /bits/ 64 <540000000>;
> + required-opps = <&rpmhpd_opp_svs_l1>;
> + };
> +
> + opp-810000000 {
> + opp-hz = /bits/ 64 <810000000>;
> + required-opps = <&rpmhpd_opp_nom>;
> + };
> + };
> + };
> + };
> +
> + mdss1_dp2_phy: phy@220c2a00 {
> + compatible = "qcom,sc8280xp-dp-phy";
> + reg = <0 0x220c2a00 0 0x19c>,
> + <0 0x220c2200 0 0xec>,
> + <0 0x220c2600 0 0xec>,
> + <0 0x220c2000 0 0x1c8>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_DPTX2_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
> + clock-names = "aux", "cfg_ahb";
> + power-domains = <&rpmhpd SC8280XP_MX>;
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + mdss1_dp3_phy: phy@220c5a00 {
> + compatible = "qcom,sc8280xp-dp-phy";
> + reg = <0 0x220c5a00 0 0x19c>,
> + <0 0x220c5200 0 0xec>,
> + <0 0x220c5600 0 0xec>,
> + <0 0x220c5000 0 0x1c8>;
> +
> + clocks = <&dispcc1 DISP_CC_MDSS_DPTX3_AUX_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
> + clock-names = "aux", "cfg_ahb";
> + power-domains = <&rpmhpd SC8280XP_MX>;
> +
> + #clock-cells = <1>;
> + #phy-cells = <0>;
> +
> + status = "disabled";
> + };
> +
> + dispcc1: clock-controller@22100000 {
> + compatible = "qcom,sc8280xp-dispcc1";
> + reg = <0 0x22100000 0 0x20000>;
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&rpmhcc RPMH_CXO_CLK>,
> + <0>,
> + <&mdss1_dp0_phy 0>,
> + <&mdss1_dp0_phy 1>,
> + <&mdss1_dp1_phy 0>,
> + <&mdss1_dp1_phy 1>,
> + <&mdss1_dp2_phy 0>,
> + <&mdss1_dp2_phy 1>,
> + <&mdss1_dp3_phy 0>,
> + <&mdss1_dp3_phy 1>,
> + <0>,
> + <0>,
> + <0>,
> + <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + #clock-cells = <1>;
> + #power-domain-cells = <1>;
> + #reset-cells = <1>;
> +
> + status = "disabled";
> + };
> };
>
> sound: sound {
On Tue, Jan 10, 2023 at 07:59:03PM -0800, Bjorn Andersson wrote:
> From: Bjorn Andersson <bjorn.andersson@linaro.org>
>
> Define the display clock controllers, the MDSS instances, the DP phys
> and connect these together.
>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
> ---
>
> Changes since v6:
> - Dropped assigned-clock-rate on MDP_CLK
> - Rearranged the properties in all nodes
>
> arch/arm64/boot/dts/qcom/sc8280xp.dtsi | 811 +++++++++++++++++++++++++
> 1 file changed, 811 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> index 0ea2f19d471b..2ed17baf50d3 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
> + mdss0_mdp: display-controller@ae01000 {
> + compatible = "qcom,sc8280xp-dpu";
> + reg = <0 0x0ae01000 0 0x8f000>,
> + <0 0x0aeb0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc0 DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus",
> + "nrt_bus",
> + "iface",
> + "lut",
> + "core",
> + "vsync";
> + interrupt-parent = <&mdss0>;
> + interrupts = <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <19200000>;
Nit: Shouldn't these come after the clock-names property as they did in
v5 so that the clock properties are grouped?
> + operating-points-v2 = <&mdss0_mdp_opp_table>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@5 {
> + reg = <5>;
> + mdss0_intf5_out: endpoint {
> + remote-endpoint = <&mdss0_dp3_in>;
> + };
> + };
> +
> + port@6 {
> + reg = <6>;
> + mdss0_intf6_out: endpoint {
> + remote-endpoint = <&mdss0_dp2_in>;
> + };
> + };
> + };
> + mdss0_dp2: displayport-controller@ae9a000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0xae9a000 0 0x200>,
> + <0 0xae9a200 0 0x200>,
> + <0 0xae9a400 0 0x600>,
> + <0 0xae9b000 0 0x400>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss0>;
> + interrupts = <14>;
> + phys = <&mdss0_dp2_phy>;
> + phy-names = "dp";
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
> + <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss0_dp2_phy 0>, <&mdss0_dp2_phy 1>;
Same here.
> + operating-points-v2 = <&mdss0_dp2_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> + mdss0_dp3: displayport-controller@aea0000 {
> + compatible = "qcom,sc8280xp-dp";
> + reg = <0 0xaea0000 0 0x200>,
> + <0 0xaea0200 0 0x200>,
> + <0 0xaea0400 0 0x600>,
> + <0 0xaea1000 0 0x400>;
> +
> + clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
> + clock-names = "core_iface", "core_aux",
> + "ctrl_link",
> + "ctrl_link_iface", "stream_pixel";
> + interrupt-parent = <&mdss0>;
> + interrupts = <15>;
> + phys = <&mdss0_dp3_phy>;
> + phy-names = "dp";
> + power-domains = <&dispcc0 MDSS_GDSC>;
> +
> + assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
> + <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
> + assigned-clock-parents = <&mdss0_dp3_phy 0>, <&mdss0_dp3_phy 1>;
And here.
> + operating-points-v2 = <&mdss0_dp3_opp_table>;
> +
> + #sound-dai-cells = <0>;
> +
> + status = "disabled";
> + mdss1: display-subsystem@22000000 {
> + compatible = "qcom,sc8280xp-mdss";
> + reg = <0 0x22000000 0 0x1000>;
> + reg-names = "mdss";
> +
> + clocks = <&gcc GCC_DISP_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_CLK>;
> + clock-names = "iface",
> + "ahb",
> + "core";
> + interconnects = <&mmss_noc MASTER_MDP_CORE1_0 0 &mc_virt SLAVE_EBI1 0>,
> + <&mmss_noc MASTER_MDP_CORE1_1 0 &mc_virt SLAVE_EBI1 0>;
> + interconnect-names = "mdp0-mem", "mdp1-mem";
> + interrupts = <GIC_SPI 865 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-controller;
This is a provider property so perhaps it should go before
'#interrupt-cells' as it did above?
> +
> + iommus = <&apps_smmu 0x1800 0x402>;
> + power-domains = <&dispcc1 MDSS_GDSC>;
> + resets = <&dispcc1 DISP_CC_MDSS_CORE_BCR>;
> +
> + #interrupt-cells = <1>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + status = "disabled";
> +
> + mdss1_mdp: display-controller@22001000 {
> + compatible = "qcom,sc8280xp-dpu";
> + reg = <0 0x22001000 0 0x8f000>,
> + <0 0x220b0000 0 0x2008>;
> + reg-names = "mdp", "vbif";
> +
> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> + <&gcc GCC_DISP_SF_AXI_CLK>,
> + <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_LUT_CLK>,
> + <&dispcc1 DISP_CC_MDSS_MDP_CLK>,
> + <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
> + clock-names = "bus",
> + "nrt_bus",
> + "iface",
> + "lut",
> + "core",
> + "vsync";
> + interrupt-parent = <&mdss1>;
> + interrupts = <0>;
> + power-domains = <&rpmhpd SC8280XP_MMCX>;
> +
> + assigned-clocks = <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
> + assigned-clock-rates = <19200000>;
Move after 'clock-names'?
There are a few more instances like this below.
Johan
@@ -4,6 +4,7 @@
* Copyright (c) 2022, Linaro Limited
*/
+#include <dt-bindings/clock/qcom,dispcc-sc8280xp.h>
#include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
@@ -2097,6 +2098,42 @@ usb_1_qmpphy: phy@8903000 {
status = "disabled";
};
+ mdss1_dp0_phy: phy@8909a00 {
+ compatible = "qcom,sc8280xp-dp-phy";
+ reg = <0 0x08909a00 0 0x19c>,
+ <0 0x08909200 0 0xec>,
+ <0 0x08909600 0 0xec>,
+ <0 0x08909000 0 0x1c8>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_DPTX0_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+ power-domains = <&rpmhpd SC8280XP_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ mdss1_dp1_phy: phy@890ca00 {
+ compatible = "qcom,sc8280xp-dp-phy";
+ reg = <0 0x0890ca00 0 0x19c>,
+ <0 0x0890c200 0 0xec>,
+ <0 0x0890c600 0 0xec>,
+ <0 0x0890c000 0 0x1c8>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_DPTX1_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+ power-domains = <&rpmhpd SC8280XP_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
pmu@9091000 {
compatible = "qcom,sc8280xp-llcc-bwmon", "qcom,sc7280-llcc-bwmon";
reg = <0 0x9091000 0 0x1000>;
@@ -2303,6 +2340,314 @@ usb_1_dwc3: usb@a800000 {
};
};
+ mdss0: display-subsystem@ae00000 {
+ compatible = "qcom,sc8280xp-mdss";
+ reg = <0 0x0ae00000 0 0x1000>;
+ reg-names = "mdss";
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc0 DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface",
+ "ahb",
+ "core";
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>,
+ <&mmss_noc MASTER_MDP1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+ iommus = <&apps_smmu 0x1000 0x402>;
+ power-domains = <&dispcc0 MDSS_GDSC>;
+ resets = <&dispcc0 DISP_CC_MDSS_CORE_BCR>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss0_mdp: display-controller@ae01000 {
+ compatible = "qcom,sc8280xp-dpu";
+ reg = <0 0x0ae01000 0 0x8f000>,
+ <0 0x0aeb0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc0 DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc0 DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+ interrupt-parent = <&mdss0>;
+ interrupts = <0>;
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ assigned-clocks = <&dispcc0 DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <19200000>;
+ operating-points-v2 = <&mdss0_mdp_opp_table>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@5 {
+ reg = <5>;
+ mdss0_intf5_out: endpoint {
+ remote-endpoint = <&mdss0_dp3_in>;
+ };
+ };
+
+ port@6 {
+ reg = <6>;
+ mdss0_intf6_out: endpoint {
+ remote-endpoint = <&mdss0_dp2_in>;
+ };
+ };
+ };
+
+ mdss0_mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ required-opps = <&rpmhpd_opp_turbo_l1>;
+ };
+ };
+ };
+
+ mdss0_dp2: displayport-controller@ae9a000 {
+ compatible = "qcom,sc8280xp-dp";
+ reg = <0 0xae9a000 0 0x200>,
+ <0 0xae9a200 0 0x200>,
+ <0 0xae9a400 0 0x600>,
+ <0 0xae9b000 0 0x400>;
+
+ clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+ interrupt-parent = <&mdss0>;
+ interrupts = <14>;
+ phys = <&mdss0_dp2_phy>;
+ phy-names = "dp";
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
+ <&dispcc0 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss0_dp2_phy 0>, <&mdss0_dp2_phy 1>;
+ operating-points-v2 = <&mdss0_dp2_opp_table>;
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss0_dp2_in: endpoint {
+ remote-endpoint = <&mdss0_intf6_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss0_dp2_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss0_dp3: displayport-controller@aea0000 {
+ compatible = "qcom,sc8280xp-dp";
+ reg = <0 0xaea0000 0 0x200>,
+ <0 0xaea0200 0 0x200>,
+ <0 0xaea0400 0 0x600>,
+ <0 0xaea1000 0 0x400>;
+
+ clocks = <&dispcc0 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
+ <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+ interrupt-parent = <&mdss0>;
+ interrupts = <15>;
+ phys = <&mdss0_dp3_phy>;
+ phy-names = "dp";
+ power-domains = <&dispcc0 MDSS_GDSC>;
+
+ assigned-clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
+ <&dispcc0 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss0_dp3_phy 0>, <&mdss0_dp3_phy 1>;
+ operating-points-v2 = <&mdss0_dp3_opp_table>;
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss0_dp3_in: endpoint {
+ remote-endpoint = <&mdss0_intf5_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss0_dp3_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+ };
+
+ mdss0_dp2_phy: phy@aec2a00 {
+ compatible = "qcom,sc8280xp-dp-phy";
+ reg = <0 0x0aec2a00 0 0x19c>,
+ <0 0x0aec2200 0 0xec>,
+ <0 0x0aec2600 0 0xec>,
+ <0 0x0aec2000 0 0x1c8>;
+
+ clocks = <&dispcc0 DISP_CC_MDSS_DPTX2_AUX_CLK>,
+ <&dispcc0 DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+ power-domains = <&rpmhpd SC8280XP_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ mdss0_dp3_phy: phy@aec5a00 {
+ compatible = "qcom,sc8280xp-dp-phy";
+ reg = <0 0x0aec5a00 0 0x19c>,
+ <0 0x0aec5200 0 0xec>,
+ <0 0x0aec5600 0 0xec>,
+ <0 0x0aec5000 0 0x1c8>;
+
+ clocks = <&dispcc0 DISP_CC_MDSS_DPTX3_AUX_CLK>,
+ <&dispcc0 DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+ power-domains = <&rpmhpd SC8280XP_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ dispcc0: clock-controller@af00000 {
+ compatible = "qcom,sc8280xp-dispcc0";
+ reg = <0 0x0af00000 0 0x20000>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&sleep_clk>,
+ <0>,
+ <0>,
+ <0>,
+ <0>,
+ <&mdss0_dp2_phy 0>,
+ <&mdss0_dp2_phy 1>,
+ <&mdss0_dp3_phy 0>,
+ <&mdss0_dp3_phy 1>,
+ <0>,
+ <0>,
+ <0>,
+ <0>;
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ #clock-cells = <1>;
+ #power-domain-cells = <1>;
+ #reset-cells = <1>;
+
+ status = "disabled";
+ };
+
pdc: interrupt-controller@b220000 {
compatible = "qcom,sc8280xp-pdc", "qcom,pdc";
reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
@@ -2925,6 +3270,472 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
qcom,remote-pid = <12>;
};
};
+
+ mdss1: display-subsystem@22000000 {
+ compatible = "qcom,sc8280xp-mdss";
+ reg = <0 0x22000000 0 0x1000>;
+ reg-names = "mdss";
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc1 DISP_CC_MDSS_MDP_CLK>;
+ clock-names = "iface",
+ "ahb",
+ "core";
+ interconnects = <&mmss_noc MASTER_MDP_CORE1_0 0 &mc_virt SLAVE_EBI1 0>,
+ <&mmss_noc MASTER_MDP_CORE1_1 0 &mc_virt SLAVE_EBI1 0>;
+ interconnect-names = "mdp0-mem", "mdp1-mem";
+ interrupts = <GIC_SPI 865 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+
+ iommus = <&apps_smmu 0x1800 0x402>;
+ power-domains = <&dispcc1 MDSS_GDSC>;
+ resets = <&dispcc1 DISP_CC_MDSS_CORE_BCR>;
+
+ #interrupt-cells = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ status = "disabled";
+
+ mdss1_mdp: display-controller@22001000 {
+ compatible = "qcom,sc8280xp-dpu";
+ reg = <0 0x22001000 0 0x8f000>,
+ <0 0x220b0000 0 0x2008>;
+ reg-names = "mdp", "vbif";
+
+ clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+ <&gcc GCC_DISP_SF_AXI_CLK>,
+ <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc1 DISP_CC_MDSS_MDP_LUT_CLK>,
+ <&dispcc1 DISP_CC_MDSS_MDP_CLK>,
+ <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
+ clock-names = "bus",
+ "nrt_bus",
+ "iface",
+ "lut",
+ "core",
+ "vsync";
+ interrupt-parent = <&mdss1>;
+ interrupts = <0>;
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ assigned-clocks = <&dispcc1 DISP_CC_MDSS_VSYNC_CLK>;
+ assigned-clock-rates = <19200000>;
+ operating-points-v2 = <&mdss1_mdp_opp_table>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss1_intf0_out: endpoint {
+ remote-endpoint = <&mdss1_dp0_in>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ mdss1_intf4_out: endpoint {
+ remote-endpoint = <&mdss1_dp1_in>;
+ };
+ };
+
+ port@5 {
+ reg = <5>;
+ mdss1_intf5_out: endpoint {
+ remote-endpoint = <&mdss1_dp3_in>;
+ };
+ };
+
+ port@6 {
+ reg = <6>;
+ mdss1_intf6_out: endpoint {
+ remote-endpoint = <&mdss1_dp2_in>;
+ };
+ };
+ };
+
+ mdss1_mdp_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-200000000 {
+ opp-hz = /bits/ 64 <200000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-300000000 {
+ opp-hz = /bits/ 64 <300000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-375000000 {
+ opp-hz = /bits/ 64 <375000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ opp-600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ required-opps = <&rpmhpd_opp_turbo_l1>;
+ };
+ };
+ };
+
+ mdss1_dp0: displayport-controller@22090000 {
+ compatible = "qcom,sc8280xp-dp";
+ reg = <0 0x22090000 0 0x200>,
+ <0 0x22090200 0 0x200>,
+ <0 0x22090400 0 0x600>,
+ <0 0x22091000 0 0x400>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX0_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX0_PIXEL0_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+ interrupt-parent = <&mdss1>;
+ interrupts = <12>;
+ phys = <&mdss1_dp0_phy>;
+ phy-names = "dp";
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>,
+ <&dispcc1 DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss1_dp0_phy 0>, <&mdss1_dp0_phy 1>;
+ operating-points-v2 = <&mdss1_dp0_opp_table>;
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss1_dp0_in: endpoint {
+ remote-endpoint = <&mdss1_intf0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss1_dp0_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+
+ };
+
+ mdss1_dp1: displayport-controller@22098000 {
+ compatible = "qcom,sc8280xp-dp";
+ reg = <0 0x22098000 0 0x200>,
+ <0 0x22098200 0 0x200>,
+ <0 0x22098400 0 0x600>,
+ <0 0x22099000 0 0x400>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX1_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX1_PIXEL0_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+ interrupt-parent = <&mdss1>;
+ interrupts = <13>;
+ phys = <&mdss1_dp1_phy>;
+ phy-names = "dp";
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>,
+ <&dispcc1 DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss1_dp1_phy 0>, <&mdss1_dp1_phy 1>;
+ operating-points-v2 = <&mdss1_dp1_opp_table>;
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss1_dp1_in: endpoint {
+ remote-endpoint = <&mdss1_intf4_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss1_dp1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss1_dp2: displayport-controller@2209a000 {
+ compatible = "qcom,sc8280xp-dp";
+ reg = <0 0x2209a000 0 0x200>,
+ <0 0x2209a200 0 0x200>,
+ <0 0x2209a400 0 0x600>,
+ <0 0x2209b000 0 0x400>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX2_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_INTF_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX2_PIXEL0_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+ interrupt-parent = <&mdss1>;
+ interrupts = <14>;
+ phys = <&mdss1_dp2_phy>;
+ phy-names = "dp";
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX2_LINK_CLK_SRC>,
+ <&dispcc1 DISP_CC_MDSS_DPTX2_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss1_dp2_phy 0>, <&mdss1_dp2_phy 1>;
+ operating-points-v2 = <&mdss1_dp2_opp_table>;
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss1_dp2_in: endpoint {
+ remote-endpoint = <&mdss1_intf6_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss1_dp2_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
+ mdss1_dp3: displayport-controller@220a0000 {
+ compatible = "qcom,sc8280xp-dp";
+ reg = <0 0x220a0000 0 0x200>,
+ <0 0x220a0200 0 0x200>,
+ <0 0x220a0400 0 0x600>,
+ <0 0x220a1000 0 0x400>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_AHB_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX3_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_INTF_CLK>,
+ <&dispcc1 DISP_CC_MDSS_DPTX3_PIXEL0_CLK>;
+ clock-names = "core_iface", "core_aux",
+ "ctrl_link",
+ "ctrl_link_iface", "stream_pixel";
+ interrupt-parent = <&mdss1>;
+ interrupts = <15>;
+ phys = <&mdss1_dp3_phy>;
+ phy-names = "dp";
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ assigned-clocks = <&dispcc1 DISP_CC_MDSS_DPTX3_LINK_CLK_SRC>,
+ <&dispcc1 DISP_CC_MDSS_DPTX3_PIXEL0_CLK_SRC>;
+ assigned-clock-parents = <&mdss1_dp3_phy 0>, <&mdss1_dp3_phy 1>;
+ operating-points-v2 = <&mdss1_dp3_opp_table>;
+
+ #sound-dai-cells = <0>;
+
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mdss1_dp3_in: endpoint {
+ remote-endpoint = <&mdss1_intf5_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+
+ mdss1_dp3_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-160000000 {
+ opp-hz = /bits/ 64 <160000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-270000000 {
+ opp-hz = /bits/ 64 <270000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-540000000 {
+ opp-hz = /bits/ 64 <540000000>;
+ required-opps = <&rpmhpd_opp_svs_l1>;
+ };
+
+ opp-810000000 {
+ opp-hz = /bits/ 64 <810000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+ };
+
+ mdss1_dp2_phy: phy@220c2a00 {
+ compatible = "qcom,sc8280xp-dp-phy";
+ reg = <0 0x220c2a00 0 0x19c>,
+ <0 0x220c2200 0 0xec>,
+ <0 0x220c2600 0 0xec>,
+ <0 0x220c2000 0 0x1c8>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_DPTX2_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+ power-domains = <&rpmhpd SC8280XP_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ mdss1_dp3_phy: phy@220c5a00 {
+ compatible = "qcom,sc8280xp-dp-phy";
+ reg = <0 0x220c5a00 0 0x19c>,
+ <0 0x220c5200 0 0xec>,
+ <0 0x220c5600 0 0xec>,
+ <0 0x220c5000 0 0x1c8>;
+
+ clocks = <&dispcc1 DISP_CC_MDSS_DPTX3_AUX_CLK>,
+ <&dispcc1 DISP_CC_MDSS_AHB_CLK>;
+ clock-names = "aux", "cfg_ahb";
+ power-domains = <&rpmhpd SC8280XP_MX>;
+
+ #clock-cells = <1>;
+ #phy-cells = <0>;
+
+ status = "disabled";
+ };
+
+ dispcc1: clock-controller@22100000 {
+ compatible = "qcom,sc8280xp-dispcc1";
+ reg = <0 0x22100000 0 0x20000>;
+
+ clocks = <&gcc GCC_DISP_AHB_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <0>,
+ <&mdss1_dp0_phy 0>,
+ <&mdss1_dp0_phy 1>,
+ <&mdss1_dp1_phy 0>,
+ <&mdss1_dp1_phy 1>,
+ <&mdss1_dp2_phy 0>,
+ <&mdss1_dp2_phy 1>,
+ <&mdss1_dp3_phy 0>,
+ <&mdss1_dp3_phy 1>,
+ <0>,
+ <0>,
+ <0>,
+ <0>;
+ power-domains = <&rpmhpd SC8280XP_MMCX>;
+
+ #clock-cells = <1>;
+ #power-domain-cells = <1>;
+ #reset-cells = <1>;
+
+ status = "disabled";
+ };
};
sound: sound {