diff mbox series

[1/2] drm/mediatek: dsi: Reduce the time of dsi from LP11 to sending cmd

Message ID 1672974321-18947-2-git-send-email-xinlei.lee@mediatek.com
State New
Headers
Series Reduce lcm_reset to DSI LP11 send cmd time |

Commit Message

Xinlei Lee (李昕磊) Jan. 6, 2023, 3:05 a.m. UTC 
  From: Xinlei Lee <xinlei.lee@mediatek.com>

According to Figure 16 Turnaround Procedure on page 36 in [1], you
can see the status of LP-00 -> LP10 -> LP11. This state can correspond
to the state of DSI from LP00 -> LP11 in mtk_dsi_lane_ready function
in mtk_dsi.c.

LP-00 -> LP10 -> LP11 takes about 2*TLPX time (refer to [1] page 51
to see that TLPX is 50ns).

The delay at the end of the mtk_dsi_lane_ready function should be
greater than the 2*TLPX specified by the DSI spec, and less than
the time specified by the DSI_RX (generally 6ms to 40ms), to avoid
problems caused by the RX specification.

[1]:mipi_D-PHY_specification_v1-1

Fixes: 39e8d062b03c ("drm/mediatek: Keep dsi as LP00 before dcs cmds transfer")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

Comments

Sam Ravnborg Jan. 7, 2023, 8:29 p.m. UTC | #1 
On Fri, Jan 06, 2023 at 11:05:20AM +0800, xinlei.lee@mediatek.com wrote:
> From: Xinlei Lee <xinlei.lee@mediatek.com>
> 
> According to Figure 16 Turnaround Procedure on page 36 in [1], you
> can see the status of LP-00 -> LP10 -> LP11. This state can correspond
> to the state of DSI from LP00 -> LP11 in mtk_dsi_lane_ready function
> in mtk_dsi.c.
> 
> LP-00 -> LP10 -> LP11 takes about 2*TLPX time (refer to [1] page 51
> to see that TLPX is 50ns).
> 
> The delay at the end of the mtk_dsi_lane_ready function should be
> greater than the 2*TLPX specified by the DSI spec, and less than
> the time specified by the DSI_RX (generally 6ms to 40ms), to avoid
> problems caused by the RX specification.
> 
> [1]:mipi_D-PHY_specification_v1-1
> 
> Fixes: 39e8d062b03c ("drm/mediatek: Keep dsi as LP00 before dcs cmds transfer")
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>

Seems OK.
Acked-by: Sam Ravnborg <sam@ravnborg.org>

> ---
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
> index 3b7d13028fb6..9e1363c9fcdb 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dsi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
> @@ -721,7 +721,7 @@ static void mtk_dsi_lane_ready(struct mtk_dsi *dsi)
>  		mtk_dsi_clk_ulp_mode_leave(dsi);
>  		mtk_dsi_lane0_ulp_mode_leave(dsi);
>  		mtk_dsi_clk_hs_mode(dsi, 0);
> -		msleep(20);
> +		usleep_range(1000, 3000);
>  		/* The reaction time after pulling up the mipi signal for dsi_rx */
>  	}
>  }
> -- 
> 2.18.0
AngeloGioacchino Del Regno Jan. 9, 2023, 11:26 a.m. UTC | #2 
Il 06/01/23 04:05, xinlei.lee@mediatek.com ha scritto:
> From: Xinlei Lee <xinlei.lee@mediatek.com>
> 
> According to Figure 16 Turnaround Procedure on page 36 in [1], you
> can see the status of LP-00 -> LP10 -> LP11. This state can correspond
> to the state of DSI from LP00 -> LP11 in mtk_dsi_lane_ready function
> in mtk_dsi.c.
> 
> LP-00 -> LP10 -> LP11 takes about 2*TLPX time (refer to [1] page 51
> to see that TLPX is 50ns).
> 
> The delay at the end of the mtk_dsi_lane_ready function should be
> greater than the 2*TLPX specified by the DSI spec, and less than
> the time specified by the DSI_RX (generally 6ms to 40ms), to avoid
> problems caused by the RX specification.
> 
> [1]:mipi_D-PHY_specification_v1-1
> 
> Fixes: 39e8d062b03c ("drm/mediatek: Keep dsi as LP00 before dcs cmds transfer")
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
diff mbox series

Patch

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index 3b7d13028fb6..9e1363c9fcdb 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -721,7 +721,7 @@  static void mtk_dsi_lane_ready(struct mtk_dsi *dsi)
 		mtk_dsi_clk_ulp_mode_leave(dsi);
 		mtk_dsi_lane0_ulp_mode_leave(dsi);
 		mtk_dsi_clk_hs_mode(dsi, 0);
-		msleep(20);
+		usleep_range(1000, 3000);
 		/* The reaction time after pulling up the mipi signal for dsi_rx */
 	}
 }