deleted file mode 100644
@@ -1,121 +0,0 @@
-Qualcomm MSM8974 TLMM block
-
-Required properties:
-- compatible: "qcom,msm8974-pinctrl"
-- reg: Should be the base address and length of the TLMM block.
-- interrupts: Should be the parent IRQ of the TLMM block.
-- interrupt-controller: Marks the device node as an interrupt controller.
-- #interrupt-cells: Should be two.
-- gpio-controller: Marks the device node as a GPIO controller.
-- #gpio-cells : Should be two.
- The first cell is the gpio pin number and the
- second cell is used for optional parameters.
-- gpio-ranges: see ../gpio/gpio.txt
-
-Optional properties:
-
-- gpio-reserved-ranges: see ../gpio/gpio.txt
-
-Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
-a general description of GPIO and interrupt bindings.
-
-Please refer to pinctrl-bindings.txt in this directory for details of the
-common pinctrl bindings used by client devices, including the meaning of the
-phrase "pin configuration node".
-
-Qualcomm's pin configuration nodes act as a container for an arbitrary number of
-subnodes. Each of these subnodes represents some desired configuration for a
-pin, a group, or a list of pins or groups. This configuration can include the
-mux function to select on those pin(s)/group(s), and various pin configuration
-parameters, such as pull-up, drive strength, etc.
-
-The name of each subnode is not important; all subnodes should be enumerated
-and processed purely based on their content.
-
-Each subnode only affects those parameters that are explicitly listed. In
-other words, a subnode that lists a mux function but no pin configuration
-parameters implies no information about any pin configuration parameters.
-Similarly, a pin subnode that describes a pullup parameter implies no
-information about e.g. the mux function.
-
-
-The following generic properties as defined in pinctrl-bindings.txt are valid
-to specify in a pin configuration subnode:
- pins, function, bias-disable, bias-pull-down, bias-pull-up, drive-strength.
-
-Non-empty subnodes must specify the 'pins' property.
-Note that not all properties are valid for all pins.
-
-
-Valid values for pins are:
- gpio0-gpio145
- Supports mux, bias and drive-strength
-
- sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, sdc2_data
- Supports bias and drive-strength
-
- hsic_data, hsic_strobe
- Supports only mux
-
-Valid values for function are:
- cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
- blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1,
- blsp_uim2, blsp_uart2, blsp_i2c2, blsp_spi2,
- blsp_uim3, blsp_uart3, blsp_i2c3, blsp_spi3,
- blsp_uim4, blsp_uart4, blsp_i2c4, blsp_spi4,
- blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5,
- blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6,
- blsp_uim7, blsp_uart7, blsp_i2c7, blsp_spi7,
- blsp_uim8, blsp_uart8, blsp_i2c8, blsp_spi8,
- blsp_uim9, blsp_uart9, blsp_i2c9, blsp_spi9,
- blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10,
- blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11,
- blsp_uim12, blsp_uart12, blsp_i2c12, blsp_spi12,
- blsp_spi1_cs1, blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2
- blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
- sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0, cci_timer1,
- cci_timer2, cci_timer3, cci_async_in0, cci_async_in1, cci_async_in2,
- cam_mckl0, cam_mclk1, cam_mclk2, cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc,
- hdmi_hpd, edp_hpd, gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk,
- gp_mn, tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s, spkr_mi2s,
- ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl, gpio
-
- (Note that this is not yet the complete list of functions)
-
-
-
-Example:
-
- msmgpio: pinctrl@fd510000 {
- compatible = "qcom,msm8974-pinctrl";
- reg = <0xfd510000 0x4000>;
-
- gpio-controller;
- #gpio-cells = <2>;
- gpio-ranges = <&msmgpio 0 0 146>;
- interrupt-controller;
- #interrupt-cells = <2>;
- interrupts = <0 208 0>;
-
- pinctrl-names = "default";
- pinctrl-0 = <&uart2_default>;
-
- uart2_default: uart2_default {
- mux {
- pins = "gpio4", "gpio5";
- function = "blsp_uart2";
- };
-
- tx {
- pins = "gpio4";
- drive-strength = <4>;
- bias-disable;
- };
-
- rx {
- pins = "gpio5";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
- };
new file mode 100644
@@ -0,0 +1,179 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/qcom,msm8974-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm MSM8974 TLMM pin controller
+
+maintainers:
+ - Bjorn Andersson <andersson@kernel.org>
+ - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+description:
+ Top Level Mode Multiplexer pin controller in Qualcomm MSM8974 SoC.
+
+properties:
+ compatible:
+ const: qcom,msm8974-pinctrl
+
+ reg:
+ maxItems: 1
+
+ interrupts: true
+ interrupt-controller: true
+ "#interrupt-cells": true
+ gpio-controller: true
+ "#gpio-cells": true
+ gpio-ranges: true
+ wakeup-parent: true
+
+ gpio-reserved-ranges:
+ minItems: 1
+ maxItems: 73
+
+ gpio-line-names:
+ maxItems: 146
+
+patternProperties:
+ "-state$":
+ oneOf:
+ - $ref: "#/$defs/qcom-msm8974-tlmm-state"
+ - patternProperties:
+ "-pins$":
+ $ref: "#/$defs/qcom-msm8974-tlmm-state"
+ additionalProperties: false
+
+$defs:
+ qcom-msm8974-tlmm-state:
+ type: object
+ description:
+ Pinctrl node's client devices use subnodes for desired pin configuration.
+ Client device subnodes use below standard properties.
+ $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
+
+ properties:
+ pins:
+ description:
+ List of gpio pins affected by the properties specified in this
+ subnode.
+ items:
+ oneOf:
+ - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-3][0-9]|14[0-5])$"
+ - enum: [ hsic_data, hsic_strobe, sdc1_clk, sdc1_cmd, sdc1_data,
+ sdc2_clk, sdc2_cmd, sdc2_data ]
+ minItems: 1
+ maxItems: 36
+
+ function:
+ description:
+ Specify the alternative function to be configured for the specified
+ pins.
+
+ enum: [ gpio, cci_i2c0, cci_i2c1, uim1, uim2, uim_batt_alarm,
+ blsp_uim1, blsp_uart1, blsp_i2c1, blsp_spi1, blsp_uim2,
+ blsp_uart2, blsp_i2c2, blsp_spi2, blsp_uim3, blsp_uart3,
+ blsp_i2c3, blsp_spi3, blsp_uim4, blsp_uart4, blsp_i2c4,
+ blsp_spi4, blsp_uim5, blsp_uart5, blsp_i2c5, blsp_spi5,
+ blsp_uim6, blsp_uart6, blsp_i2c6, blsp_spi6, blsp_uim7,
+ blsp_uart7, blsp_i2c7, blsp_spi7, blsp_uim8, blsp_uart8,
+ blsp_i2c8, blsp_spi8, blsp_uim9, blsp_uart9, blsp_i2c9,
+ blsp_spi9, blsp_uim10, blsp_uart10, blsp_i2c10, blsp_spi10,
+ blsp_uim11, blsp_uart11, blsp_i2c11, blsp_spi11, blsp_uim12,
+ blsp_uart12, blsp_i2c12, blsp_spi12, blsp_spi1_cs1,
+ blsp_spi2_cs2, blsp_spi_cs3, blsp_spi2_cs1, blsp_spi2_cs2
+ blsp_spi2_cs3, blsp_spi10_cs1, blsp_spi10_cs2, blsp_spi10_cs3,
+ sdc3, sdc4, gcc_gp_clk1, gcc_gp_clk2, gcc_gp_clk3, cci_timer0,
+ cci_timer1, cci_timer2, cci_timer3, cci_async_in0,
+ cci_async_in1, cci_async_in2, cam_mckl0, cam_mclk1, cam_mclk2,
+ cam_mclk3, mdp_vsync, hdmi_cec, hdmi_ddc, hdmi_hpd, edp_hpd,
+ gp_pdm0, gp_pdm1, gp_pdm2, gp_pdm3, gp0_clk, gp1_clk, gp_mn,
+ tsif1, tsif2, hsic, grfc, audio_ref_clk, qua_mi2s, pri_mi2s,
+ spkr_mi2s, ter_mi2s, sec_mi2s, bt, fm, wlan, slimbus, hsic_ctl ]
+
+ bias-pull-down: true
+ bias-pull-up: true
+ bias-disable: true
+ drive-strength: true
+ input-enable: true
+ output-high: true
+ output-low: true
+
+ required:
+ - pins
+
+ allOf:
+ - if:
+ properties:
+ pins:
+ contains:
+ enum:
+ - hsic_data
+ - hsic_strobe
+ required:
+ - pins
+ then:
+ properties:
+ bias-pull-down: false
+ bias-pull-up: false
+ bias-disable: false
+ drive-strength: false
+ input-enable: false
+ output-high: false
+ output-low: false
+
+ additionalProperties: false
+
+allOf:
+ - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ tlmm: pinctrl@fd510000 {
+ compatible = "qcom,msm8974-pinctrl";
+ reg = <0xfd510000 0x4000>;
+ gpio-controller;
+ gpio-ranges = <&tlmm 0 0 146>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+ sdc1-off-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
+
+ blsp2-uart1-sleep-state {
+ pins = "gpio41", "gpio42", "gpio43", "gpio44";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ hsic-state {
+ pins = "hsic_data", "hsic_strobe";
+ };
+ };