[v2,06/12] riscv: dts: allwinner: Add Allwinner D1 Nezha devicetree
Commit Message
"D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
plus low-speed I/O from the SoC and a GPIO expander chip.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
---
Changes in v2:
- Common regulators moved to MangoPi MQ patch, removed analog LDOs
- Removed LRADC (depends on analog LDOs)
- Added XR829 host-wake interrupt
arch/riscv/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun20i-d1-nezha.dts | 167 ++++++++++++++++++
2 files changed, 168 insertions(+)
create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
Comments
Reviewed-by: Guo Ren <guoren@kernel.org>
On Sat, Nov 26, 2022 at 7:47 AM Samuel Holland <samuel@sholland.org> wrote:
>
> "D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
> It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
> HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
> plus low-speed I/O from the SoC and a GPIO expander chip.
>
> Reviewed-by: Heiko Stuebner <heiko@sntech.de>
> Tested-by: Conor Dooley <conor.dooley@microchip.com>
> Tested-by: Heiko Stuebner <heiko@sntech.de>
> Signed-off-by: Samuel Holland <samuel@sholland.org>
> ---
>
> Changes in v2:
> - Common regulators moved to MangoPi MQ patch, removed analog LDOs
> - Removed LRADC (depends on analog LDOs)
> - Added XR829 host-wake interrupt
>
> arch/riscv/boot/dts/allwinner/Makefile | 1 +
> .../boot/dts/allwinner/sun20i-d1-nezha.dts | 167 ++++++++++++++++++
> 2 files changed, 168 insertions(+)
> create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
>
> diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
> index 2f2792594f7d..277e59d1c907 100644
> --- a/arch/riscv/boot/dts/allwinner/Makefile
> +++ b/arch/riscv/boot/dts/allwinner/Makefile
> @@ -1,2 +1,3 @@
> # SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
> diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
> new file mode 100644
> index 000000000000..9ea3648e64ea
> --- /dev/null
> +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
> @@ -0,0 +1,167 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +
> +/dts-v1/;
> +
> +#include "sun20i-d1.dtsi"
> +#include "sun20i-common-regulators.dtsi"
> +
> +/ {
> + model = "Allwinner D1 Nezha";
> + compatible = "allwinner,d1-nezha", "allwinner,sun20i-d1";
> +
> + aliases {
> + ethernet0 = &emac;
> + ethernet1 = &xr829;
> + mmc0 = &mmc0;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + reg_usbvbus: usbvbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usbvbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
> + enable-active-high;
> + vin-supply = <®_vcc>;
> + };
> +
> + /*
> + * This regulator is PWM-controlled, but the PWM controller is not
> + * yet supported, so fix the regulator to its default voltage.
> + */
> + reg_vdd_cpu: vdd-cpu {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd-cpu";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1100000>;
> + vin-supply = <®_vcc>;
> + };
> +
> + wifi_pwrseq: wifi-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
> + };
> +};
> +
> +&cpu0 {
> + cpu-supply = <®_vdd_cpu>;
> +};
> +
> +&dcxo {
> + clock-frequency = <24000000>;
> +};
> +
> +&ehci0 {
> + status = "okay";
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&emac {
> + pinctrl-0 = <&rgmii_pe_pins>;
> + pinctrl-names = "default";
> + phy-handle = <&ext_rgmii_phy>;
> + phy-mode = "rgmii-id";
> + phy-supply = <®_vcc_3v3>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-0 = <&i2c2_pb0_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + pcf8574a: gpio@38 {
> + compatible = "nxp,pcf8574a";
> + reg = <0x38>;
> + interrupt-parent = <&pio>;
> + interrupts = <1 2 IRQ_TYPE_LEVEL_LOW>; /* PB2 */
> + interrupt-controller;
> + gpio-controller;
> + #gpio-cells = <2>;
> + #interrupt-cells = <2>;
> + };
> +};
> +
> +&mdio {
> + ext_rgmii_phy: ethernet-phy@1 {
> + compatible = "ethernet-phy-ieee802.3-c22";
> + reg = <1>;
> + };
> +};
> +
> +&mmc0 {
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + disable-wp;
> + vmmc-supply = <®_vcc_3v3>;
> + vqmmc-supply = <®_vcc_3v3>;
> + pinctrl-0 = <&mmc0_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&mmc1 {
> + bus-width = <4>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + non-removable;
> + vmmc-supply = <®_vcc_3v3>;
> + vqmmc-supply = <®_vcc_3v3>;
> + pinctrl-0 = <&mmc1_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + xr829: wifi@1 {
> + reg = <1>;
> + interrupt-parent = <&pio>;
> + interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
> + interrupt-names = "host-wake";
> + };
> +};
> +
> +&ohci0 {
> + status = "okay";
> +};
> +
> +&ohci1 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + pinctrl-0 = <&uart0_pb8_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&uart1 {
> + uart-has-rtscts;
> + pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + /* XR829 bluetooth is connected here */
> +};
> +
> +&usb_otg {
> + dr_mode = "otg";
> + status = "okay";
> +};
> +
> +&usbphy {
> + usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
> + usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
> + usb0_vbus-supply = <®_usbvbus>;
> + usb1_vbus-supply = <®_vcc>;
> + status = "okay";
> +};
> --
> 2.37.4
>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Am Samstag, 26. November 2022, 00:46:50 CET schrieb Samuel Holland:
> "D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
> It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
> HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
> plus low-speed I/O from the SoC and a GPIO expander chip.
>
> Reviewed-by: Heiko Stuebner <heiko@sntech.de>
> Tested-by: Conor Dooley <conor.dooley@microchip.com>
> Tested-by: Heiko Stuebner <heiko@sntech.de>
> Signed-off-by: Samuel Holland <samuel@sholland.org>
just to confirm the tags above, the board still runs nicely.
Thanks
Heiko
Dne sobota, 26. november 2022 ob 00:46:50 CET je Samuel Holland napisal(a):
> "D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
> It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
> HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
> plus low-speed I/O from the SoC and a GPIO expander chip.
>
> Reviewed-by: Heiko Stuebner <heiko@sntech.de>
> Tested-by: Conor Dooley <conor.dooley@microchip.com>
> Tested-by: Heiko Stuebner <heiko@sntech.de>
> Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Best regards,
Jernej
@@ -1,2 +1,3 @@
# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
new file mode 100644
@@ -0,0 +1,167 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel@sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+ model = "Allwinner D1 Nezha";
+ compatible = "allwinner,d1-nezha", "allwinner,sun20i-d1";
+
+ aliases {
+ ethernet0 = &emac;
+ ethernet1 = &xr829;
+ mmc0 = &mmc0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_usbvbus: usbvbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbvbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+ enable-active-high;
+ vin-supply = <®_vcc>;
+ };
+
+ /*
+ * This regulator is PWM-controlled, but the PWM controller is not
+ * yet supported, so fix the regulator to its default voltage.
+ */
+ reg_vdd_cpu: vdd-cpu {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd-cpu";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <®_vcc>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+ };
+};
+
+&cpu0 {
+ cpu-supply = <®_vdd_cpu>;
+};
+
+&dcxo {
+ clock-frequency = <24000000>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-0 = <&rgmii_pe_pins>;
+ pinctrl-names = "default";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-mode = "rgmii-id";
+ phy-supply = <®_vcc_3v3>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-0 = <&i2c2_pb0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ pcf8574a: gpio@38 {
+ compatible = "nxp,pcf8574a";
+ reg = <0x38>;
+ interrupt-parent = <&pio>;
+ interrupts = <1 2 IRQ_TYPE_LEVEL_LOW>; /* PB2 */
+ interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ };
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ disable-wp;
+ vmmc-supply = <®_vcc_3v3>;
+ vqmmc-supply = <®_vcc_3v3>;
+ pinctrl-0 = <&mmc0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&mmc1 {
+ bus-width = <4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ vmmc-supply = <®_vcc_3v3>;
+ vqmmc-supply = <®_vcc_3v3>;
+ pinctrl-0 = <&mmc1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ xr829: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&pio>;
+ interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+ interrupt-names = "host-wake";
+ };
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pb8_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ uart-has-rtscts;
+ pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /* XR829 bluetooth is connected here */
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
+ usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+ usb0_vbus-supply = <®_usbvbus>;
+ usb1_vbus-supply = <®_vcc>;
+ status = "okay";
+};