On Thu, Nov 24, 2022 at 06:20:54PM +0800, Pin-yen Lin wrote:
> Register USB Type-C mode switches when the "mode-switch" property and
> relevant port are available in Device Tree. Configure the crosspoint
> switch based on the entered alternate mode for a specific Type-C
> connector.
...
> +static void anx7625_typec_two_ports_update(struct anx7625_data *ctx)
> +{
> + if (ctx->typec_ports[0].dp_connected && ctx->typec_ports[1].dp_connected)
> + /* Both ports available, do nothing to retain the current one. */
> + return;
> + else if (ctx->typec_ports[0].dp_connected)
This 'else' is redundant. I would rewrite above as
/* Check if both ports available and do nothing to retain the current one */
if (ctx->typec_ports[0].dp_connected && ctx->typec_ports[1].dp_connected)
return;
if (ctx->typec_ports[0].dp_connected)
> + anx7625_set_crosspoint_switch(ctx, TYPEC_ORIENTATION_NORMAL);
> + else if (ctx->typec_ports[1].dp_connected)
> + anx7625_set_crosspoint_switch(ctx, TYPEC_ORIENTATION_REVERSE);
> +}
...
> + data->dp_connected = (state->alt && state->alt->svid == USB_TYPEC_DP_SID &&
> + state->alt->mode == USB_TYPEC_DP_MODE);
Parentheses are not needed.
...
> + /*
> + * <0 1> refers to SSRX1/SSTX1, and <2 3> refers to SSRX2/SSTX2.
> + */
> + for (i = 0; i < num_lanes; i++) {
> + if (port_num != -1 && port_num != dp_lanes[i] / 2) {
> + dev_err(dev, "Invalid data lane numbers\n");
> + return -EINVAL;
> + }
According to Rob Linux must not validate device tree. If you need it, use
proper YAML schema.
> + port_num = dp_lanes[i] / 2;
> + }
...
> + if (!ctx->num_typec_switches) {
> + dev_warn(dev, "No Type-C switches node found\n");
> + return ret;
Why not to return 0 explicitly?
> + }
...
> + ctx->typec_ports = devm_kcalloc(
Broken indentation.
> + dev, ctx->num_typec_switches, sizeof(struct anx7625_port_data),
> + GFP_KERNEL);
> + if (!ctx->typec_ports)
> + return -ENOMEM;
...
> +struct anx7625_port_data {
> + bool dp_connected;
You can save some bytes on some architectures if move this to be last field.
> + struct typec_mux_dev *typec_mux;
> + struct anx7625_data *ctx;
> +};
Hi Andy,
Thanks for reviewing the patch.
On Thu, Nov 24, 2022 at 8:18 PM Andy Shevchenko
<andriy.shevchenko@linux.intel.com> wrote:
>
> On Thu, Nov 24, 2022 at 06:20:54PM +0800, Pin-yen Lin wrote:
> > Register USB Type-C mode switches when the "mode-switch" property and
> > relevant port are available in Device Tree. Configure the crosspoint
> > switch based on the entered alternate mode for a specific Type-C
> > connector.
>
> ...
>
> > +static void anx7625_typec_two_ports_update(struct anx7625_data *ctx)
> > +{
> > + if (ctx->typec_ports[0].dp_connected && ctx->typec_ports[1].dp_connected)
> > + /* Both ports available, do nothing to retain the current one. */
> > + return;
>
> > + else if (ctx->typec_ports[0].dp_connected)
>
> This 'else' is redundant. I would rewrite above as
>
> /* Check if both ports available and do nothing to retain the current one */
> if (ctx->typec_ports[0].dp_connected && ctx->typec_ports[1].dp_connected)
> return;
>
> if (ctx->typec_ports[0].dp_connected)
>
> > + anx7625_set_crosspoint_switch(ctx, TYPEC_ORIENTATION_NORMAL);
> > + else if (ctx->typec_ports[1].dp_connected)
> > + anx7625_set_crosspoint_switch(ctx, TYPEC_ORIENTATION_REVERSE);
> > +}
Thanks for the detailed suggestion. I'll adapt this in v7.
>
> ...
>
> > + data->dp_connected = (state->alt && state->alt->svid == USB_TYPEC_DP_SID &&
> > + state->alt->mode == USB_TYPEC_DP_MODE);
>
> Parentheses are not needed.
Will fix this in v7.
>
> ...
>
> > + /*
> > + * <0 1> refers to SSRX1/SSTX1, and <2 3> refers to SSRX2/SSTX2.
> > + */
> > + for (i = 0; i < num_lanes; i++) {
>
> > + if (port_num != -1 && port_num != dp_lanes[i] / 2) {
> > + dev_err(dev, "Invalid data lane numbers\n");
> > + return -EINVAL;
> > + }
>
> According to Rob Linux must not validate device tree. If you need it, use
> proper YAML schema.
>
> > + port_num = dp_lanes[i] / 2;
> > + }
>
I'll remove this from the driver in v7.
> ...
>
> > + if (!ctx->num_typec_switches) {
> > + dev_warn(dev, "No Type-C switches node found\n");
>
> > + return ret;
>
> Why not to return 0 explicitly?
Will update to just "return 0" in v7.
>
> > + }
>
> ...
>
> > + ctx->typec_ports = devm_kcalloc(
>
> Broken indentation.
Will fix in v7
>
> > + dev, ctx->num_typec_switches, sizeof(struct anx7625_port_data),
> > + GFP_KERNEL);
> > + if (!ctx->typec_ports)
> > + return -ENOMEM;
>
> ...
>
> > +struct anx7625_port_data {
>
> > + bool dp_connected;
>
> You can save some bytes on some architectures if move this to be last field.
Thanks for the suggestion. I'll do so in v7
>
> > + struct typec_mux_dev *typec_mux;
> > + struct anx7625_data *ctx;
> > +};
>
> --
> With Best Regards,
> Andy Shevchenko
>
>
@@ -34,6 +34,7 @@ config DRM_ANALOGIX_ANX7625
tristate "Analogix Anx7625 MIPI to DP interface support"
depends on DRM
depends on OF
+ depends on TYPEC || TYPEC=n
select DRM_DISPLAY_DP_HELPER
select DRM_DISPLAY_HDCP_HELPER
select DRM_DISPLAY_HELPER
@@ -15,6 +15,8 @@
#include <linux/regulator/consumer.h>
#include <linux/slab.h>
#include <linux/types.h>
+#include <linux/usb/typec_dp.h>
+#include <linux/usb/typec_mux.h>
#include <linux/workqueue.h>
#include <linux/of_gpio.h>
@@ -2573,6 +2575,167 @@ static void anx7625_runtime_disable(void *data)
pm_runtime_disable(data);
}
+static void anx7625_set_crosspoint_switch(struct anx7625_data *ctx,
+ enum typec_orientation orientation)
+{
+ if (orientation == TYPEC_ORIENTATION_NORMAL) {
+ anx7625_reg_write(ctx, ctx->i2c.tcpc_client, TCPC_SWITCH_0,
+ SW_SEL1_SSRX_RX1 | SW_SEL1_DPTX0_RX2);
+ anx7625_reg_write(ctx, ctx->i2c.tcpc_client, TCPC_SWITCH_1,
+ SW_SEL2_SSTX_TX1 | SW_SEL2_DPTX1_TX2);
+ } else if (orientation == TYPEC_ORIENTATION_REVERSE) {
+ anx7625_reg_write(ctx, ctx->i2c.tcpc_client, TCPC_SWITCH_0,
+ SW_SEL1_SSRX_RX2 | SW_SEL1_DPTX0_RX1);
+ anx7625_reg_write(ctx, ctx->i2c.tcpc_client, TCPC_SWITCH_1,
+ SW_SEL2_SSTX_TX2 | SW_SEL2_DPTX1_TX1);
+ }
+}
+
+static void anx7625_typec_two_ports_update(struct anx7625_data *ctx)
+{
+ if (ctx->typec_ports[0].dp_connected && ctx->typec_ports[1].dp_connected)
+ /* Both ports available, do nothing to retain the current one. */
+ return;
+ else if (ctx->typec_ports[0].dp_connected)
+ anx7625_set_crosspoint_switch(ctx, TYPEC_ORIENTATION_NORMAL);
+ else if (ctx->typec_ports[1].dp_connected)
+ anx7625_set_crosspoint_switch(ctx, TYPEC_ORIENTATION_REVERSE);
+}
+
+static int anx7625_typec_mux_set(struct typec_mux_dev *mux,
+ struct typec_mux_state *state)
+{
+ struct anx7625_port_data *data = typec_mux_get_drvdata(mux);
+ struct anx7625_data *ctx = data->ctx;
+ struct device *dev = &ctx->client->dev;
+ bool new_dp_connected, old_dp_connected;
+
+ if (ctx->num_typec_switches == 1)
+ return 0;
+
+ old_dp_connected = ctx->typec_ports[0].dp_connected || ctx->typec_ports[1].dp_connected;
+
+ data->dp_connected = (state->alt && state->alt->svid == USB_TYPEC_DP_SID &&
+ state->alt->mode == USB_TYPEC_DP_MODE);
+
+ dev_dbg(dev, "mux_set dp_connected: c0=%d, c1=%d\n",
+ ctx->typec_ports[0].dp_connected, ctx->typec_ports[1].dp_connected);
+
+ new_dp_connected = ctx->typec_ports[0].dp_connected || ctx->typec_ports[1].dp_connected;
+
+ /* dp on, power on first */
+ if (!old_dp_connected && new_dp_connected)
+ pm_runtime_get_sync(dev);
+
+ anx7625_typec_two_ports_update(ctx);
+
+ /* dp off, power off last */
+ if (old_dp_connected && !new_dp_connected)
+ pm_runtime_put_sync(dev);
+
+ return 0;
+}
+
+static int anx7625_register_mode_switch(struct device *dev, struct device_node *node,
+ struct anx7625_data *ctx)
+{
+ struct anx7625_port_data *port_data;
+ struct typec_mux_desc mux_desc = {};
+ char name[32];
+ u32 dp_lanes[2];
+ int ret, num_lanes, i, port_num = -1;
+
+ num_lanes = drm_of_get_data_lanes_count(node, 0, 2);
+ if (num_lanes < 0) {
+ dev_err(dev, "Error on getting data lanes count: %d\n", num_lanes);
+ return num_lanes;
+ }
+
+ ret = of_property_read_u32_array(node, "data-lanes", dp_lanes, num_lanes);
+ if (ret) {
+ dev_err(dev, "Failed to read the data-lanes variable: %d\n",
+ ret);
+ return ret;
+ }
+
+ /*
+ * <0 1> refers to SSRX1/SSTX1, and <2 3> refers to SSRX2/SSTX2.
+ */
+ for (i = 0; i < num_lanes; i++) {
+ if (port_num != -1 && port_num != dp_lanes[i] / 2) {
+ dev_err(dev, "Invalid data lane numbers\n");
+ return -EINVAL;
+ }
+ port_num = dp_lanes[i] / 2;
+ }
+
+ port_data = &ctx->typec_ports[port_num];
+ port_data->ctx = ctx;
+ mux_desc.fwnode = &node->fwnode;
+ mux_desc.drvdata = port_data;
+ snprintf(name, sizeof(name), "%s-%u", node->name, port_num);
+ mux_desc.name = name;
+ mux_desc.set = anx7625_typec_mux_set;
+
+ port_data->typec_mux = typec_mux_register(dev, &mux_desc);
+ if (IS_ERR(port_data->typec_mux)) {
+ ret = PTR_ERR(port_data->typec_mux);
+ dev_err(dev, "Mode switch register for port %d failed: %d\n",
+ port_num, ret);
+ }
+
+ return ret;
+}
+
+static void anx7625_unregister_typec_switches(struct anx7625_data *ctx)
+{
+ int i;
+
+ for (i = 0; i < ctx->num_typec_switches; i++)
+ typec_mux_unregister(ctx->typec_ports[i].typec_mux);
+}
+
+static int anx7625_register_typec_switches(struct device *dev, struct anx7625_data *ctx)
+{
+ struct device_node *port, *sw;
+ int ret = 0;
+
+ port = of_graph_get_port_by_id(dev->of_node, 1);
+
+ for_each_child_of_node(port, sw) {
+ if (of_property_read_bool(sw, "mode-switch"))
+ ctx->num_typec_switches++;
+ }
+
+ if (!ctx->num_typec_switches) {
+ dev_warn(dev, "No Type-C switches node found\n");
+ return ret;
+ }
+
+ ctx->typec_ports = devm_kcalloc(
+ dev, ctx->num_typec_switches, sizeof(struct anx7625_port_data),
+ GFP_KERNEL);
+ if (!ctx->typec_ports)
+ return -ENOMEM;
+
+ /* Register switches for each connector. */
+ for_each_child_of_node(port, sw) {
+ if (!of_property_read_bool(sw, "mode-switch"))
+ continue;
+ ret = anx7625_register_mode_switch(dev, sw, ctx);
+ if (ret) {
+ dev_err(dev, "Failed to register mode switch: %d\n", ret);
+ of_node_put(sw);
+ break;
+ }
+ }
+
+ if (ret)
+ anx7625_unregister_typec_switches(ctx);
+
+ return ret;
+}
+
static int anx7625_i2c_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
@@ -2681,6 +2844,10 @@ static int anx7625_i2c_probe(struct i2c_client *client,
if (platform->pdata.intp_irq)
queue_work(platform->workqueue, &platform->work);
+ ret = anx7625_register_typec_switches(dev, platform);
+ if (ret && ret != -ENODEV)
+ dev_warn(dev, "Didn't register Type-C switches, err: %d\n", ret);
+
platform->bridge.funcs = &anx7625_bridge_funcs;
platform->bridge.of_node = client->dev.of_node;
if (!anx7625_of_panel_on_aux_bus(&client->dev))
@@ -2732,6 +2899,8 @@ static void anx7625_i2c_remove(struct i2c_client *client)
drm_bridge_remove(&platform->bridge);
+ anx7625_unregister_typec_switches(platform);
+
if (platform->pdata.intp_irq)
destroy_workqueue(platform->workqueue);
@@ -55,6 +55,18 @@
#define HPD_STATUS_CHANGE 0x80
#define HPD_STATUS 0x80
+#define TCPC_SWITCH_0 0xB4
+#define SW_SEL1_DPTX0_RX2 BIT(0)
+#define SW_SEL1_DPTX0_RX1 BIT(1)
+#define SW_SEL1_SSRX_RX2 BIT(4)
+#define SW_SEL1_SSRX_RX1 BIT(5)
+
+#define TCPC_SWITCH_1 0xB5
+#define SW_SEL2_DPTX1_TX2 BIT(0)
+#define SW_SEL2_DPTX1_TX1 BIT(1)
+#define SW_SEL2_SSTX_TX2 BIT(4)
+#define SW_SEL2_SSTX_TX1 BIT(5)
+
/******** END of I2C Address 0x58 ********/
/***************************************************************/
@@ -449,6 +461,12 @@ struct anx7625_i2c_client {
struct i2c_client *tcpc_client;
};
+struct anx7625_port_data {
+ bool dp_connected;
+ struct typec_mux_dev *typec_mux;
+ struct anx7625_data *ctx;
+};
+
struct anx7625_data {
struct anx7625_platform_data pdata;
struct platform_device *audio_pdev;
@@ -479,6 +497,8 @@ struct anx7625_data {
struct drm_connector *connector;
struct mipi_dsi_device *dsi;
struct drm_dp_aux aux;
+ int num_typec_switches;
+ struct anx7625_port_data *typec_ports;
};
#endif /* __ANX7625_H__ */