diff mbox series

[07/33] ARM: dts: aspeed: p10 and tacoma: Set FSI clock frequency

Message ID 20240215220759.976998-8-eajames@linux.ibm.com
State New
Headers
Series fsi: Interrupt support |

Commit Message

Eddie James Feb. 15, 2024, 10:07 p.m. UTC 
  Now that the driver doesn't hardcode the clock divider, set it
in the device tree.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
---
 arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts | 1 +
 arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi     | 1 +
 2 files changed, 2 insertions(+)

Comments

Krzysztof Kozlowski Feb. 16, 2024, 8:08 a.m. UTC | #1 
On 15/02/2024 23:07, Eddie James wrote:
> Now that the driver doesn't hardcode the clock divider, set it
> in the device tree.
> 
> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> ---
>  arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts | 1 +
>  arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi     | 1 +
>  2 files changed, 2 insertions(+)

Please do not mix DTS patches with driver code. DTS goes to the end
because driver code CANNOT depend on it (there are exceptions but it was
not explained here).

Best regards,
Krzysztof
Eddie James Feb. 16, 2024, 7:14 p.m. UTC | #2 
On 2/16/24 02:08, Krzysztof Kozlowski wrote:
> On 15/02/2024 23:07, Eddie James wrote:
>> Now that the driver doesn't hardcode the clock divider, set it
>> in the device tree.
>>
>> Signed-off-by: Eddie James <eajames@linux.ibm.com>
>> ---
>>   arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts | 1 +
>>   arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi     | 1 +
>>   2 files changed, 2 insertions(+)
> Please do not mix DTS patches with driver code. DTS goes to the end
> because driver code CANNOT depend on it (there are exceptions but it was
> not explained here).


Sure, I didn't realize. Thanks.

Eddie


>
> Best regards,
> Krzysztof
>
Joel Stanley Feb. 22, 2024, 12:33 p.m. UTC | #3 
On Sat, 17 Feb 2024 at 05:44, Eddie James <eajames@linux.ibm.com> wrote:
>
>
> On 2/16/24 02:08, Krzysztof Kozlowski wrote:
> > On 15/02/2024 23:07, Eddie James wrote:
> >> Now that the driver doesn't hardcode the clock divider, set it
> >> in the device tree.
> >>
> >> Signed-off-by: Eddie James <eajames@linux.ibm.com>
> >> ---
> >>   arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts | 1 +
> >>   arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi     | 1 +
> >>   2 files changed, 2 insertions(+)
> > Please do not mix DTS patches with driver code. DTS goes to the end
> > because driver code CANNOT depend on it (there are exceptions but it was
> > not explained here).

No, this is fine. Please continue sending the patches in logical order
as you see fit.
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
index 213023bc5aec..96a8f727bc38 100644
--- a/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
+++ b/arch/arm/boot/dts/aspeed/aspeed-bmc-opp-tacoma.dts
@@ -193,6 +193,7 @@  &fsim0 {
 	#address-cells = <2>;
 	#size-cells = <0>;
 
+	clock-frequency = <100000000>;
 	fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
 	fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
 
diff --git a/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi b/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
index cc466910bb52..a93a241d005a 100644
--- a/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
+++ b/arch/arm/boot/dts/aspeed/ibm-power10-dual.dtsi
@@ -8,6 +8,7 @@  &fsim0 {
 	#size-cells = <0>;
 
 	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+	clock-frequency = <100000000>;
 
 	cfam@0,0 {
 		reg = <0 0>;