[3/3] fpga: xilinx-selectmap: add new driver
Commit Message
Xilinx 7 series FPGA can be programmed using a slave parallel port named
the SelectMAP interface in the datasheet. This slave interface is
compatible with the i.MX6 EIM bus controller but other types of external
memory mapped parallel bus might work.
xilinx-selectmap currently only supports the x8 mode where data is loaded
at one byte per rising edge of the clock, with the MSb of each byte
presented to the D0 pin.
Signed-off-by: Charles Perry <charles.perry@savoirfairelinux.com>
---
drivers/fpga/Kconfig | 8 +++
drivers/fpga/Makefile | 1 +
drivers/fpga/xilinx-core.c | 11 +++-
drivers/fpga/xilinx-core.h | 3 +-
drivers/fpga/xilinx-selectmap.c | 106 ++++++++++++++++++++++++++++++++
drivers/fpga/xilinx-spi.c | 3 +-
6 files changed, 127 insertions(+), 5 deletions(-)
create mode 100644 drivers/fpga/xilinx-selectmap.c
Comments
On Wed, Jan 31, 2024 at 06:05:33PM -0500, Charles Perry wrote:
> Xilinx 7 series FPGA can be programmed using a slave parallel port named
> the SelectMAP interface in the datasheet. This slave interface is
> compatible with the i.MX6 EIM bus controller but other types of external
> memory mapped parallel bus might work.
>
> xilinx-selectmap currently only supports the x8 mode where data is loaded
> at one byte per rising edge of the clock, with the MSb of each byte
> presented to the D0 pin.
>
> Signed-off-by: Charles Perry <charles.perry@savoirfairelinux.com>
> ---
> drivers/fpga/Kconfig | 8 +++
> drivers/fpga/Makefile | 1 +
> drivers/fpga/xilinx-core.c | 11 +++-
> drivers/fpga/xilinx-core.h | 3 +-
> drivers/fpga/xilinx-selectmap.c | 106 ++++++++++++++++++++++++++++++++
> drivers/fpga/xilinx-spi.c | 3 +-
> 6 files changed, 127 insertions(+), 5 deletions(-)
> create mode 100644 drivers/fpga/xilinx-selectmap.c
>
> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
> index d27a1ebf40838..37b35f58f0dfb 100644
> --- a/drivers/fpga/Kconfig
> +++ b/drivers/fpga/Kconfig
> @@ -67,6 +67,14 @@ config FPGA_MGR_STRATIX10_SOC
> config FPGA_MGR_XILINX_CORE
> tristate
>
> +config FPGA_MGR_XILINX_SELECTMAP
> + tristate "Xilinx Configuration over SelectMAP"
> + depends on HAS_IOMEM
> + select FPGA_MGR_XILINX_CORE
> + help
> + FPGA manager driver support for Xilinx FPGA configuration
> + over SelectMAP interface.
> +
> config FPGA_MGR_XILINX_SPI
> tristate "Xilinx Configuration over Slave Serial (SPI)"
> depends on SPI
> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
> index 7ec795b6a5a70..aeb89bb13517e 100644
> --- a/drivers/fpga/Makefile
> +++ b/drivers/fpga/Makefile
> @@ -16,6 +16,7 @@ obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) += socfpga-a10.o
> obj-$(CONFIG_FPGA_MGR_STRATIX10_SOC) += stratix10-soc.o
> obj-$(CONFIG_FPGA_MGR_TS73XX) += ts73xx-fpga.o
> obj-$(CONFIG_FPGA_MGR_XILINX_CORE) += xilinx-core.o
> +obj-$(CONFIG_FPGA_MGR_XILINX_SELECTMAP) += xilinx-selectmap.o
> obj-$(CONFIG_FPGA_MGR_XILINX_SPI) += xilinx-spi.o
> obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o
> obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA) += zynqmp-fpga.o
> diff --git a/drivers/fpga/xilinx-core.c b/drivers/fpga/xilinx-core.c
> index aff40e9394085..64117759be100 100644
> --- a/drivers/fpga/xilinx-core.c
> +++ b/drivers/fpga/xilinx-core.c
> @@ -180,21 +180,26 @@ static const struct fpga_manager_ops xilinx_core_ops = {
>
> int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
> xilinx_write_func write,
> - xilinx_write_one_dummy_byte_func write_one_dummy_byte)
> + xilinx_write_one_dummy_byte_func write_one_dummy_byte,
> + const char *prog_con_id, const char *init_con_id)
These gpio name inputs are not necessary except for DTS format concern.
Is it possible we don't change the names?
> {
> struct fpga_manager *mgr;
>
> + if (!core || !dev || !write || !write_one_dummy_byte || !prog_con_id ||
> + !init_con_id)
> + return -EINVAL;
These checks belong to Patch #1.
> +
> core->dev = dev;
> core->write = write;
> core->write_one_dummy_byte = write_one_dummy_byte;
>
> /* PROGRAM_B is active low */
> - core->prog_b = devm_gpiod_get(dev, "prog_b", GPIOD_OUT_LOW);
> + core->prog_b = devm_gpiod_get(dev, prog_con_id, GPIOD_OUT_LOW);
> if (IS_ERR(core->prog_b))
> return dev_err_probe(dev, PTR_ERR(core->prog_b),
> "Failed to get PROGRAM_B gpio\n");
>
> - core->init_b = devm_gpiod_get_optional(dev, "init-b", GPIOD_IN);
> + core->init_b = devm_gpiod_get_optional(dev, init_con_id, GPIOD_IN);
> if (IS_ERR(core->init_b))
> return dev_err_probe(dev, PTR_ERR(core->init_b),
> "Failed to get INIT_B gpio\n");
> diff --git a/drivers/fpga/xilinx-core.h b/drivers/fpga/xilinx-core.h
> index 40e120945ba70..817f0e551d093 100644
> --- a/drivers/fpga/xilinx-core.h
> +++ b/drivers/fpga/xilinx-core.h
> @@ -22,6 +22,7 @@ struct xilinx_fpga_core {
>
> int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
> xilinx_write_func write,
> - xilinx_write_one_dummy_byte_func write_one_dummy_byte);
> + xilinx_write_one_dummy_byte_func write_one_dummy_byte,
> + const char *prog_con_id, const char *init_con_id);
>
> #endif /* __XILINX_CORE_H */
> diff --git a/drivers/fpga/xilinx-selectmap.c b/drivers/fpga/xilinx-selectmap.c
> new file mode 100644
> index 0000000000000..08054e19bb498
> --- /dev/null
> +++ b/drivers/fpga/xilinx-selectmap.c
> @@ -0,0 +1,106 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Xilinx Spartan6 and 7 Series SelectMAP interface driver
> + *
> + * (C) 2024 Charles Perry <charles.perry@savoirfairelinux.com>
> + *
> + * Manage Xilinx FPGA firmware loaded over the SelectMAP configuration
> + * interface.
> + */
> +
> +#include "xilinx-core.h"
> +
> +#include <linux/platform_device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/mod_devicetable.h>
> +#include <linux/of.h>
> +#include <linux/io.h>
> +
> +struct xilinx_selectmap_conf {
> + struct xilinx_fpga_core core;
> + void __iomem *base;
> + struct gpio_desc *csi_b;
> + struct gpio_desc *rdwr_b;
These 2 gpio_desc are not used globally, maybe remove them here.
> +};
> +
> +#define to_xilinx_selectmap_conf(obj) \
> + container_of(obj, struct xilinx_selectmap_conf, core)
> +
> +static int xilinx_selectmap_write(struct xilinx_fpga_core *core,
> + const char *buf, size_t count)
> +{
> + struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
> + u32 i;
> +
> + for (i = 0; i < count; ++i)
> + writeb(buf[i], conf->base);
> +
> + return 0;
> +}
> +
> +static int xilinx_selectmap_apply_padding(struct xilinx_fpga_core *core)
> +{
> + struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
> +
> + writeb(0xFF, conf->base);
Seems only one callback needed. Just use write() to xfer 1 byte?
Thanks,
Yilun
> + return 0;
> +}
> +
> +static int xilinx_selectmap_probe(struct platform_device *pdev)
> +{
> + struct xilinx_selectmap_conf *conf;
> + struct resource *r;
> + void __iomem *base;
> +
> + conf = devm_kzalloc(&pdev->dev, sizeof(*conf), GFP_KERNEL);
> + if (!conf)
> + return -ENOMEM;
> +
> + base = devm_platform_get_and_ioremap_resource(pdev, 0, &r);
> + if (IS_ERR(base))
> + return dev_err_probe(&pdev->dev, PTR_ERR(base),
> + "ioremap error\n");
> + conf->base = base;
> +
> + /* CSI_B is active low */
> + conf->csi_b =
> + devm_gpiod_get_optional(&pdev->dev, "csi", GPIOD_OUT_HIGH);
> + if (IS_ERR(conf->csi_b))
> + return dev_err_probe(&pdev->dev, PTR_ERR(conf->csi_b),
> + "Failed to get CSI_B gpio\n");
> +
> + /* RDWR_B is active low */
> + conf->rdwr_b =
> + devm_gpiod_get_optional(&pdev->dev, "rdwr", GPIOD_OUT_HIGH);
> + if (IS_ERR(conf->rdwr_b))
> + return dev_err_probe(&pdev->dev, PTR_ERR(conf->rdwr_b),
> + "Failed to get RDWR_B gpio\n");
> +
> + return xilinx_core_probe(&conf->core, &pdev->dev,
> + xilinx_selectmap_write,
> + xilinx_selectmap_apply_padding, "prog",
> + "init");
> +}
> +
> +static const struct of_device_id xlnx_selectmap_of_match[] = {
> + {
> + .compatible = "xlnx,fpga-selectmap",
> + },
> + {}
> +};
> +MODULE_DEVICE_TABLE(of, xlnx_selectmap_of_match);
> +
> +static struct platform_driver xilinx_selectmap_driver = {
> + .driver = {
> + .name = "xilinx-selectmap",
> + .of_match_table = xlnx_selectmap_of_match,
> + },
> + .probe = xilinx_selectmap_probe,
> +};
> +
> +module_platform_driver(xilinx_selectmap_driver);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Charles Perry <charles.perry@savoirfairelinux.com>");
> +MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SelectMap");
> diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
> index ec128dee97312..b9ab3d5da004c 100644
> --- a/drivers/fpga/xilinx-spi.c
> +++ b/drivers/fpga/xilinx-spi.c
> @@ -74,7 +74,8 @@ static int xilinx_spi_probe(struct spi_device *spi)
> conf->spi = spi;
>
> return xilinx_core_probe(&conf->core, &spi->dev, xilinx_spi_write,
> - xilinx_spi_apply_cclk_cycles);
> + xilinx_spi_apply_cclk_cycles, "prog_b",
> + "init-b");
> }
>
> #ifdef CONFIG_OF
> --
> 2.43.0
>
>
On Feb 4, 2024, at 3:10 AM, Xu Yilun yilun.xu@linux.intel.com wrote:
> On Wed, Jan 31, 2024 at 06:05:33PM -0500, Charles Perry wrote:
>> Xilinx 7 series FPGA can be programmed using a slave parallel port named
>> the SelectMAP interface in the datasheet. This slave interface is
>> compatible with the i.MX6 EIM bus controller but other types of external
>> memory mapped parallel bus might work.
>>
>> xilinx-selectmap currently only supports the x8 mode where data is loaded
>> at one byte per rising edge of the clock, with the MSb of each byte
>> presented to the D0 pin.
>>
>> Signed-off-by: Charles Perry <charles.perry@savoirfairelinux.com>
>> ---
>> drivers/fpga/Kconfig | 8 +++
>> drivers/fpga/Makefile | 1 +
>> drivers/fpga/xilinx-core.c | 11 +++-
>> drivers/fpga/xilinx-core.h | 3 +-
>> drivers/fpga/xilinx-selectmap.c | 106 ++++++++++++++++++++++++++++++++
>> drivers/fpga/xilinx-spi.c | 3 +-
>> 6 files changed, 127 insertions(+), 5 deletions(-)
>> create mode 100644 drivers/fpga/xilinx-selectmap.c
>>
>> diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
>> index d27a1ebf40838..37b35f58f0dfb 100644
>> --- a/drivers/fpga/Kconfig
>> +++ b/drivers/fpga/Kconfig
>> @@ -67,6 +67,14 @@ config FPGA_MGR_STRATIX10_SOC
>> config FPGA_MGR_XILINX_CORE
>> tristate
>>
>> +config FPGA_MGR_XILINX_SELECTMAP
>> + tristate "Xilinx Configuration over SelectMAP"
>> + depends on HAS_IOMEM
>> + select FPGA_MGR_XILINX_CORE
>> + help
>> + FPGA manager driver support for Xilinx FPGA configuration
>> + over SelectMAP interface.
>> +
>> config FPGA_MGR_XILINX_SPI
>> tristate "Xilinx Configuration over Slave Serial (SPI)"
>> depends on SPI
>> diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
>> index 7ec795b6a5a70..aeb89bb13517e 100644
>> --- a/drivers/fpga/Makefile
>> +++ b/drivers/fpga/Makefile
>> @@ -16,6 +16,7 @@ obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) += socfpga-a10.o
>> obj-$(CONFIG_FPGA_MGR_STRATIX10_SOC) += stratix10-soc.o
>> obj-$(CONFIG_FPGA_MGR_TS73XX) += ts73xx-fpga.o
>> obj-$(CONFIG_FPGA_MGR_XILINX_CORE) += xilinx-core.o
>> +obj-$(CONFIG_FPGA_MGR_XILINX_SELECTMAP) += xilinx-selectmap.o
>> obj-$(CONFIG_FPGA_MGR_XILINX_SPI) += xilinx-spi.o
>> obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o
>> obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA) += zynqmp-fpga.o
>> diff --git a/drivers/fpga/xilinx-core.c b/drivers/fpga/xilinx-core.c
>> index aff40e9394085..64117759be100 100644
>> --- a/drivers/fpga/xilinx-core.c
>> +++ b/drivers/fpga/xilinx-core.c
>> @@ -180,21 +180,26 @@ static const struct fpga_manager_ops xilinx_core_ops = {
>>
>> int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
>> xilinx_write_func write,
>> - xilinx_write_one_dummy_byte_func write_one_dummy_byte)
>> + xilinx_write_one_dummy_byte_func write_one_dummy_byte,
>> + const char *prog_con_id, const char *init_con_id)
>
> These gpio name inputs are not necessary except for DTS format concern.
> Is it possible we don't change the names?
>
Krzysztof won't accept the old names as they are non standard (contain a
prohibited char "_" and use a "-b" prefix for active low). I agree that it
is cumbersome to have different gpio names injected in the core by the top
level driver.
Can I change the GPIO names of xlnx,fpga-slave-serial? i.e.:
* "prog_b" -> "prog"
* "init-b" -> "init"
and keep a fallback in the driver so that current users of this driver keep
working without adaptation in the DT.
>> {
>> struct fpga_manager *mgr;
>>
>> + if (!core || !dev || !write || !write_one_dummy_byte || !prog_con_id ||
>> + !init_con_id)
>> + return -EINVAL;
>
> These checks belong to Patch #1.
>
Ok
>> +
>> core->dev = dev;
>> core->write = write;
>> core->write_one_dummy_byte = write_one_dummy_byte;
>>
>> /* PROGRAM_B is active low */
>> - core->prog_b = devm_gpiod_get(dev, "prog_b", GPIOD_OUT_LOW);
>> + core->prog_b = devm_gpiod_get(dev, prog_con_id, GPIOD_OUT_LOW);
>> if (IS_ERR(core->prog_b))
>> return dev_err_probe(dev, PTR_ERR(core->prog_b),
>> "Failed to get PROGRAM_B gpio\n");
>>
>> - core->init_b = devm_gpiod_get_optional(dev, "init-b", GPIOD_IN);
>> + core->init_b = devm_gpiod_get_optional(dev, init_con_id, GPIOD_IN);
>> if (IS_ERR(core->init_b))
>> return dev_err_probe(dev, PTR_ERR(core->init_b),
>> "Failed to get INIT_B gpio\n");
>> diff --git a/drivers/fpga/xilinx-core.h b/drivers/fpga/xilinx-core.h
>> index 40e120945ba70..817f0e551d093 100644
>> --- a/drivers/fpga/xilinx-core.h
>> +++ b/drivers/fpga/xilinx-core.h
>> @@ -22,6 +22,7 @@ struct xilinx_fpga_core {
>>
>> int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
>> xilinx_write_func write,
>> - xilinx_write_one_dummy_byte_func write_one_dummy_byte);
>> + xilinx_write_one_dummy_byte_func write_one_dummy_byte,
>> + const char *prog_con_id, const char *init_con_id);
>>
>> #endif /* __XILINX_CORE_H */
>> diff --git a/drivers/fpga/xilinx-selectmap.c b/drivers/fpga/xilinx-selectmap.c
>> new file mode 100644
>> index 0000000000000..08054e19bb498
>> --- /dev/null
>> +++ b/drivers/fpga/xilinx-selectmap.c
>> @@ -0,0 +1,106 @@
>> +// SPDX-License-Identifier: GPL-2.0-only
>> +/*
>> + * Xilinx Spartan6 and 7 Series SelectMAP interface driver
>> + *
>> + * (C) 2024 Charles Perry <charles.perry@savoirfairelinux.com>
>> + *
>> + * Manage Xilinx FPGA firmware loaded over the SelectMAP configuration
>> + * interface.
>> + */
>> +
>> +#include "xilinx-core.h"
>> +
>> +#include <linux/platform_device.h>
>> +#include <linux/gpio/consumer.h>
>> +#include <linux/module.h>
>> +#include <linux/mod_devicetable.h>
>> +#include <linux/of.h>
>> +#include <linux/io.h>
>> +
>> +struct xilinx_selectmap_conf {
>> + struct xilinx_fpga_core core;
>> + void __iomem *base;
>> + struct gpio_desc *csi_b;
>> + struct gpio_desc *rdwr_b;
>
> These 2 gpio_desc are not used globally, maybe remove them here.
>
Ok
>> +};
>> +
>> +#define to_xilinx_selectmap_conf(obj) \
>> + container_of(obj, struct xilinx_selectmap_conf, core)
>> +
>> +static int xilinx_selectmap_write(struct xilinx_fpga_core *core,
>> + const char *buf, size_t count)
>> +{
>> + struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
>> + u32 i;
>> +
>> + for (i = 0; i < count; ++i)
>> + writeb(buf[i], conf->base);
>> +
>> + return 0;
>> +}
>> +
>> +static int xilinx_selectmap_apply_padding(struct xilinx_fpga_core *core)
>> +{
>> + struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
>> +
>> + writeb(0xFF, conf->base);
>
> Seems only one callback needed. Just use write() to xfer 1 byte?
>
> Thanks,
> Yilun
>
Yes, will be changed.
Thank you,
Charles
>> + return 0;
>> +}
>> +
>> +static int xilinx_selectmap_probe(struct platform_device *pdev)
>> +{
>> + struct xilinx_selectmap_conf *conf;
>> + struct resource *r;
>> + void __iomem *base;
>> +
>> + conf = devm_kzalloc(&pdev->dev, sizeof(*conf), GFP_KERNEL);
>> + if (!conf)
>> + return -ENOMEM;
>> +
>> + base = devm_platform_get_and_ioremap_resource(pdev, 0, &r);
>> + if (IS_ERR(base))
>> + return dev_err_probe(&pdev->dev, PTR_ERR(base),
>> + "ioremap error\n");
>> + conf->base = base;
>> +
>> + /* CSI_B is active low */
>> + conf->csi_b =
>> + devm_gpiod_get_optional(&pdev->dev, "csi", GPIOD_OUT_HIGH);
>> + if (IS_ERR(conf->csi_b))
>> + return dev_err_probe(&pdev->dev, PTR_ERR(conf->csi_b),
>> + "Failed to get CSI_B gpio\n");
>> +
>> + /* RDWR_B is active low */
>> + conf->rdwr_b =
>> + devm_gpiod_get_optional(&pdev->dev, "rdwr", GPIOD_OUT_HIGH);
>> + if (IS_ERR(conf->rdwr_b))
>> + return dev_err_probe(&pdev->dev, PTR_ERR(conf->rdwr_b),
>> + "Failed to get RDWR_B gpio\n");
>> +
>> + return xilinx_core_probe(&conf->core, &pdev->dev,
>> + xilinx_selectmap_write,
>> + xilinx_selectmap_apply_padding, "prog",
>> + "init");
>> +}
>> +
>> +static const struct of_device_id xlnx_selectmap_of_match[] = {
>> + {
>> + .compatible = "xlnx,fpga-selectmap",
>> + },
>> + {}
>> +};
>> +MODULE_DEVICE_TABLE(of, xlnx_selectmap_of_match);
>> +
>> +static struct platform_driver xilinx_selectmap_driver = {
>> + .driver = {
>> + .name = "xilinx-selectmap",
>> + .of_match_table = xlnx_selectmap_of_match,
>> + },
>> + .probe = xilinx_selectmap_probe,
>> +};
>> +
>> +module_platform_driver(xilinx_selectmap_driver);
>> +
>> +MODULE_LICENSE("GPL");
>> +MODULE_AUTHOR("Charles Perry <charles.perry@savoirfairelinux.com>");
>> +MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SelectMap");
>> diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
>> index ec128dee97312..b9ab3d5da004c 100644
>> --- a/drivers/fpga/xilinx-spi.c
>> +++ b/drivers/fpga/xilinx-spi.c
>> @@ -74,7 +74,8 @@ static int xilinx_spi_probe(struct spi_device *spi)
>> conf->spi = spi;
>>
>> return xilinx_core_probe(&conf->core, &spi->dev, xilinx_spi_write,
>> - xilinx_spi_apply_cclk_cycles);
>> + xilinx_spi_apply_cclk_cycles, "prog_b",
>> + "init-b");
>> }
>>
>> #ifdef CONFIG_OF
>> --
>> 2.43.0
>>
@@ -67,6 +67,14 @@ config FPGA_MGR_STRATIX10_SOC
config FPGA_MGR_XILINX_CORE
tristate
+config FPGA_MGR_XILINX_SELECTMAP
+ tristate "Xilinx Configuration over SelectMAP"
+ depends on HAS_IOMEM
+ select FPGA_MGR_XILINX_CORE
+ help
+ FPGA manager driver support for Xilinx FPGA configuration
+ over SelectMAP interface.
+
config FPGA_MGR_XILINX_SPI
tristate "Xilinx Configuration over Slave Serial (SPI)"
depends on SPI
@@ -16,6 +16,7 @@ obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) += socfpga-a10.o
obj-$(CONFIG_FPGA_MGR_STRATIX10_SOC) += stratix10-soc.o
obj-$(CONFIG_FPGA_MGR_TS73XX) += ts73xx-fpga.o
obj-$(CONFIG_FPGA_MGR_XILINX_CORE) += xilinx-core.o
+obj-$(CONFIG_FPGA_MGR_XILINX_SELECTMAP) += xilinx-selectmap.o
obj-$(CONFIG_FPGA_MGR_XILINX_SPI) += xilinx-spi.o
obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o
obj-$(CONFIG_FPGA_MGR_ZYNQMP_FPGA) += zynqmp-fpga.o
@@ -180,21 +180,26 @@ static const struct fpga_manager_ops xilinx_core_ops = {
int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
xilinx_write_func write,
- xilinx_write_one_dummy_byte_func write_one_dummy_byte)
+ xilinx_write_one_dummy_byte_func write_one_dummy_byte,
+ const char *prog_con_id, const char *init_con_id)
{
struct fpga_manager *mgr;
+ if (!core || !dev || !write || !write_one_dummy_byte || !prog_con_id ||
+ !init_con_id)
+ return -EINVAL;
+
core->dev = dev;
core->write = write;
core->write_one_dummy_byte = write_one_dummy_byte;
/* PROGRAM_B is active low */
- core->prog_b = devm_gpiod_get(dev, "prog_b", GPIOD_OUT_LOW);
+ core->prog_b = devm_gpiod_get(dev, prog_con_id, GPIOD_OUT_LOW);
if (IS_ERR(core->prog_b))
return dev_err_probe(dev, PTR_ERR(core->prog_b),
"Failed to get PROGRAM_B gpio\n");
- core->init_b = devm_gpiod_get_optional(dev, "init-b", GPIOD_IN);
+ core->init_b = devm_gpiod_get_optional(dev, init_con_id, GPIOD_IN);
if (IS_ERR(core->init_b))
return dev_err_probe(dev, PTR_ERR(core->init_b),
"Failed to get INIT_B gpio\n");
@@ -22,6 +22,7 @@ struct xilinx_fpga_core {
int xilinx_core_probe(struct xilinx_fpga_core *core, struct device *dev,
xilinx_write_func write,
- xilinx_write_one_dummy_byte_func write_one_dummy_byte);
+ xilinx_write_one_dummy_byte_func write_one_dummy_byte,
+ const char *prog_con_id, const char *init_con_id);
#endif /* __XILINX_CORE_H */
new file mode 100644
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Xilinx Spartan6 and 7 Series SelectMAP interface driver
+ *
+ * (C) 2024 Charles Perry <charles.perry@savoirfairelinux.com>
+ *
+ * Manage Xilinx FPGA firmware loaded over the SelectMAP configuration
+ * interface.
+ */
+
+#include "xilinx-core.h"
+
+#include <linux/platform_device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/of.h>
+#include <linux/io.h>
+
+struct xilinx_selectmap_conf {
+ struct xilinx_fpga_core core;
+ void __iomem *base;
+ struct gpio_desc *csi_b;
+ struct gpio_desc *rdwr_b;
+};
+
+#define to_xilinx_selectmap_conf(obj) \
+ container_of(obj, struct xilinx_selectmap_conf, core)
+
+static int xilinx_selectmap_write(struct xilinx_fpga_core *core,
+ const char *buf, size_t count)
+{
+ struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
+ u32 i;
+
+ for (i = 0; i < count; ++i)
+ writeb(buf[i], conf->base);
+
+ return 0;
+}
+
+static int xilinx_selectmap_apply_padding(struct xilinx_fpga_core *core)
+{
+ struct xilinx_selectmap_conf *conf = to_xilinx_selectmap_conf(core);
+
+ writeb(0xFF, conf->base);
+ return 0;
+}
+
+static int xilinx_selectmap_probe(struct platform_device *pdev)
+{
+ struct xilinx_selectmap_conf *conf;
+ struct resource *r;
+ void __iomem *base;
+
+ conf = devm_kzalloc(&pdev->dev, sizeof(*conf), GFP_KERNEL);
+ if (!conf)
+ return -ENOMEM;
+
+ base = devm_platform_get_and_ioremap_resource(pdev, 0, &r);
+ if (IS_ERR(base))
+ return dev_err_probe(&pdev->dev, PTR_ERR(base),
+ "ioremap error\n");
+ conf->base = base;
+
+ /* CSI_B is active low */
+ conf->csi_b =
+ devm_gpiod_get_optional(&pdev->dev, "csi", GPIOD_OUT_HIGH);
+ if (IS_ERR(conf->csi_b))
+ return dev_err_probe(&pdev->dev, PTR_ERR(conf->csi_b),
+ "Failed to get CSI_B gpio\n");
+
+ /* RDWR_B is active low */
+ conf->rdwr_b =
+ devm_gpiod_get_optional(&pdev->dev, "rdwr", GPIOD_OUT_HIGH);
+ if (IS_ERR(conf->rdwr_b))
+ return dev_err_probe(&pdev->dev, PTR_ERR(conf->rdwr_b),
+ "Failed to get RDWR_B gpio\n");
+
+ return xilinx_core_probe(&conf->core, &pdev->dev,
+ xilinx_selectmap_write,
+ xilinx_selectmap_apply_padding, "prog",
+ "init");
+}
+
+static const struct of_device_id xlnx_selectmap_of_match[] = {
+ {
+ .compatible = "xlnx,fpga-selectmap",
+ },
+ {}
+};
+MODULE_DEVICE_TABLE(of, xlnx_selectmap_of_match);
+
+static struct platform_driver xilinx_selectmap_driver = {
+ .driver = {
+ .name = "xilinx-selectmap",
+ .of_match_table = xlnx_selectmap_of_match,
+ },
+ .probe = xilinx_selectmap_probe,
+};
+
+module_platform_driver(xilinx_selectmap_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Charles Perry <charles.perry@savoirfairelinux.com>");
+MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SelectMap");
@@ -74,7 +74,8 @@ static int xilinx_spi_probe(struct spi_device *spi)
conf->spi = spi;
return xilinx_core_probe(&conf->core, &spi->dev, xilinx_spi_write,
- xilinx_spi_apply_cclk_cycles);
+ xilinx_spi_apply_cclk_cycles, "prog_b",
+ "init-b");
}
#ifdef CONFIG_OF