diff mbox series

[v2,6/7] arm64: dts: allwinner: h616: Add DMA controller and DMA channels

Message ID 20240127163247.384439-7-wens@kernel.org
State New
Headers
Series arm64: sun50i-h616: Add DMA and SPDIF controllers |

Commit Message

Chen-Yu Tsai Jan. 27, 2024, 4:32 p.m. UTC 
  From: Chen-Yu Tsai <wens@csie.org>

The DMA controllers found on the H616 and H618 are the same as the one
found on the A100. The only difference is the DMA endpoint (DRQ) layout.

Add a device node for it, and add DMA channels for existing peripherals.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
Changes since v1:
- Fall back to A100 instead of H6
- Add DMA channels for r_i2c

 .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 41 +++++++++++++++++++
 1 file changed, 41 insertions(+)

Comments

Andre Przywara Jan. 29, 2024, 4:03 p.m. UTC | #1 
On Sun, 28 Jan 2024 00:32:46 +0800
Chen-Yu Tsai <wens@kernel.org> wrote:

> From: Chen-Yu Tsai <wens@csie.org>
> 
> The DMA controllers found on the H616 and H618 are the same as the one
> found on the A100. The only difference is the DMA endpoint (DRQ) layout.
> 
> Add a device node for it, and add DMA channels for existing peripherals.

Thanks for the changes! I compared all bits against the manual: they match.

> Signed-off-by: Chen-Yu Tsai <wens@csie.org>

Reviewed-by: Andre Przywara <andre.przywara@arm.com>

Cheers,
Andre

> ---
> Changes since v1:
> - Fall back to A100 instead of H6
> - Add DMA channels for r_i2c
> 
>  .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 41 +++++++++++++++++++
>  1 file changed, 41 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> index d549d277d972..885809137b9d 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> @@ -133,6 +133,19 @@ ccu: clock@3001000 {
>  			#reset-cells = <1>;
>  		};
>  
> +		dma: dma-controller@3002000 {
> +			compatible = "allwinner,sun50i-h616-dma",
> +				     "allwinner,sun50i-a100-dma";
> +			reg = <0x03002000 0x1000>;
> +			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
> +			clock-names = "bus", "mbus";
> +			dma-channels = <16>;
> +			dma-requests = <49>;
> +			resets = <&ccu RST_BUS_DMA>;
> +			#dma-cells = <1>;
> +		};
> +
>  		sid: efuse@3006000 {
>  			compatible = "allwinner,sun50i-h616-sid", "allwinner,sun50i-a64-sid";
>  			reg = <0x03006000 0x1000>;
> @@ -339,6 +352,8 @@ uart0: serial@5000000 {
>  			reg-shift = <2>;
>  			reg-io-width = <4>;
>  			clocks = <&ccu CLK_BUS_UART0>;
> +			dmas = <&dma 14>, <&dma 14>;
> +			dma-names = "tx", "rx";
>  			resets = <&ccu RST_BUS_UART0>;
>  			status = "disabled";
>  		};
> @@ -350,6 +365,8 @@ uart1: serial@5000400 {
>  			reg-shift = <2>;
>  			reg-io-width = <4>;
>  			clocks = <&ccu CLK_BUS_UART1>;
> +			dmas = <&dma 15>, <&dma 15>;
> +			dma-names = "tx", "rx";
>  			resets = <&ccu RST_BUS_UART1>;
>  			status = "disabled";
>  		};
> @@ -361,6 +378,8 @@ uart2: serial@5000800 {
>  			reg-shift = <2>;
>  			reg-io-width = <4>;
>  			clocks = <&ccu CLK_BUS_UART2>;
> +			dmas = <&dma 16>, <&dma 16>;
> +			dma-names = "tx", "rx";
>  			resets = <&ccu RST_BUS_UART2>;
>  			status = "disabled";
>  		};
> @@ -372,6 +391,8 @@ uart3: serial@5000c00 {
>  			reg-shift = <2>;
>  			reg-io-width = <4>;
>  			clocks = <&ccu CLK_BUS_UART3>;
> +			dmas = <&dma 17>, <&dma 17>;
> +			dma-names = "tx", "rx";
>  			resets = <&ccu RST_BUS_UART3>;
>  			status = "disabled";
>  		};
> @@ -383,6 +404,8 @@ uart4: serial@5001000 {
>  			reg-shift = <2>;
>  			reg-io-width = <4>;
>  			clocks = <&ccu CLK_BUS_UART4>;
> +			dmas = <&dma 18>, <&dma 18>;
> +			dma-names = "tx", "rx";
>  			resets = <&ccu RST_BUS_UART4>;
>  			status = "disabled";
>  		};
> @@ -394,6 +417,8 @@ uart5: serial@5001400 {
>  			reg-shift = <2>;
>  			reg-io-width = <4>;
>  			clocks = <&ccu CLK_BUS_UART5>;
> +			dmas = <&dma 19>, <&dma 19>;
> +			dma-names = "tx", "rx";
>  			resets = <&ccu RST_BUS_UART5>;
>  			status = "disabled";
>  		};
> @@ -405,6 +430,8 @@ i2c0: i2c@5002000 {
>  			reg = <0x05002000 0x400>;
>  			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&ccu CLK_BUS_I2C0>;
> +			dmas = <&dma 43>, <&dma 43>;
> +			dma-names = "rx", "tx";
>  			resets = <&ccu RST_BUS_I2C0>;
>  			pinctrl-names = "default";
>  			pinctrl-0 = <&i2c0_pins>;
> @@ -420,6 +447,8 @@ i2c1: i2c@5002400 {
>  			reg = <0x05002400 0x400>;
>  			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&ccu CLK_BUS_I2C1>;
> +			dmas = <&dma 44>, <&dma 44>;
> +			dma-names = "rx", "tx";
>  			resets = <&ccu RST_BUS_I2C1>;
>  			status = "disabled";
>  			#address-cells = <1>;
> @@ -433,6 +462,8 @@ i2c2: i2c@5002800 {
>  			reg = <0x05002800 0x400>;
>  			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&ccu CLK_BUS_I2C2>;
> +			dmas = <&dma 45>, <&dma 45>;
> +			dma-names = "rx", "tx";
>  			resets = <&ccu RST_BUS_I2C2>;
>  			status = "disabled";
>  			#address-cells = <1>;
> @@ -446,6 +477,8 @@ i2c3: i2c@5002c00 {
>  			reg = <0x05002c00 0x400>;
>  			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&ccu CLK_BUS_I2C3>;
> +			dmas = <&dma 46>, <&dma 46>;
> +			dma-names = "rx", "tx";
>  			resets = <&ccu RST_BUS_I2C3>;
>  			status = "disabled";
>  			#address-cells = <1>;
> @@ -459,6 +492,8 @@ i2c4: i2c@5003000 {
>  			reg = <0x05003000 0x400>;
>  			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&ccu CLK_BUS_I2C4>;
> +			dmas = <&dma 47>, <&dma 47>;
> +			dma-names = "rx", "tx";
>  			resets = <&ccu RST_BUS_I2C4>;
>  			status = "disabled";
>  			#address-cells = <1>;
> @@ -472,6 +507,8 @@ spi0: spi@5010000 {
>  			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
>  			clock-names = "ahb", "mod";
> +			dmas = <&dma 22>, <&dma 22>;
> +			dma-names = "rx", "tx";
>  			resets = <&ccu RST_BUS_SPI0>;
>  			status = "disabled";
>  			#address-cells = <1>;
> @@ -485,6 +522,8 @@ spi1: spi@5011000 {
>  			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
>  			clock-names = "ahb", "mod";
> +			dmas = <&dma 23>, <&dma 23>;
> +			dma-names = "rx", "tx";
>  			resets = <&ccu RST_BUS_SPI1>;
>  			status = "disabled";
>  			#address-cells = <1>;
> @@ -734,6 +773,8 @@ r_i2c: i2c@7081400 {
>  			reg = <0x07081400 0x400>;
>  			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
>  			clocks = <&r_ccu CLK_R_APB2_I2C>;
> +			dmas = <&dma 48>, <&dma 48>;
> +			dma-names = "rx", "tx";
>  			resets = <&r_ccu RST_R_APB2_I2C>;
>  			status = "disabled";
>  			#address-cells = <1>;
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
index d549d277d972..885809137b9d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -133,6 +133,19 @@  ccu: clock@3001000 {
 			#reset-cells = <1>;
 		};
 
+		dma: dma-controller@3002000 {
+			compatible = "allwinner,sun50i-h616-dma",
+				     "allwinner,sun50i-a100-dma";
+			reg = <0x03002000 0x1000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+			clock-names = "bus", "mbus";
+			dma-channels = <16>;
+			dma-requests = <49>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
 		sid: efuse@3006000 {
 			compatible = "allwinner,sun50i-h616-sid", "allwinner,sun50i-a64-sid";
 			reg = <0x03006000 0x1000>;
@@ -339,6 +352,8 @@  uart0: serial@5000000 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART0>;
+			dmas = <&dma 14>, <&dma 14>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
@@ -350,6 +365,8 @@  uart1: serial@5000400 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART1>;
+			dmas = <&dma 15>, <&dma 15>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
@@ -361,6 +378,8 @@  uart2: serial@5000800 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART2>;
+			dmas = <&dma 16>, <&dma 16>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
@@ -372,6 +391,8 @@  uart3: serial@5000c00 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART3>;
+			dmas = <&dma 17>, <&dma 17>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART3>;
 			status = "disabled";
 		};
@@ -383,6 +404,8 @@  uart4: serial@5001000 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART4>;
+			dmas = <&dma 18>, <&dma 18>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART4>;
 			status = "disabled";
 		};
@@ -394,6 +417,8 @@  uart5: serial@5001400 {
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&ccu CLK_BUS_UART5>;
+			dmas = <&dma 19>, <&dma 19>;
+			dma-names = "tx", "rx";
 			resets = <&ccu RST_BUS_UART5>;
 			status = "disabled";
 		};
@@ -405,6 +430,8 @@  i2c0: i2c@5002000 {
 			reg = <0x05002000 0x400>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C0>;
+			dmas = <&dma 43>, <&dma 43>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C0>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&i2c0_pins>;
@@ -420,6 +447,8 @@  i2c1: i2c@5002400 {
 			reg = <0x05002400 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C1>;
+			dmas = <&dma 44>, <&dma 44>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C1>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -433,6 +462,8 @@  i2c2: i2c@5002800 {
 			reg = <0x05002800 0x400>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C2>;
+			dmas = <&dma 45>, <&dma 45>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C2>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -446,6 +477,8 @@  i2c3: i2c@5002c00 {
 			reg = <0x05002c00 0x400>;
 			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C3>;
+			dmas = <&dma 46>, <&dma 46>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C3>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -459,6 +492,8 @@  i2c4: i2c@5003000 {
 			reg = <0x05003000 0x400>;
 			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C4>;
+			dmas = <&dma 47>, <&dma 47>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_I2C4>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -472,6 +507,8 @@  spi0: spi@5010000 {
 			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
 			clock-names = "ahb", "mod";
+			dmas = <&dma 22>, <&dma 22>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_SPI0>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -485,6 +522,8 @@  spi1: spi@5011000 {
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
 			clock-names = "ahb", "mod";
+			dmas = <&dma 23>, <&dma 23>;
+			dma-names = "rx", "tx";
 			resets = <&ccu RST_BUS_SPI1>;
 			status = "disabled";
 			#address-cells = <1>;
@@ -734,6 +773,8 @@  r_i2c: i2c@7081400 {
 			reg = <0x07081400 0x400>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			dmas = <&dma 48>, <&dma 48>;
+			dma-names = "rx", "tx";
 			resets = <&r_ccu RST_R_APB2_I2C>;
 			status = "disabled";
 			#address-cells = <1>;