staging: pi433: set DCC setting to spec recommended value

Message ID Y3k0bbM2/5jXfNKQ@qemulion
State New
Headers
Series staging: pi433: set DCC setting to spec recommended value |

Commit Message

Deepak R Varma Nov. 19, 2022, 7:54 p.m. UTC
  The DCCFreq value is used to obtain the DC offset canceller cut-off
frequency. Upon device power reset, the bits 7-5 of the RegRxBw register
that represent the DCCFreq setting are set to 0x4, which evaluates the
cut-off frequency to be 1% of RxBw.

In the current implementation, first, there is no configuration variable
defined in the struct pi433_rx_cfg for the user to set this value as
part of the UAPI. Second, the code simply ignores the value of DCC
setting and allows it to never change.

As per the RFM69HCW tech specs, the default value for DCC frequency is
recommended to be 4% of the RxBw; which requires the DCC setting bits
to be set to 010. So allow the DCC setting to change to recommended /
default value for improved rx sensitivity.

Signed-off-by: Deepak R Varma <drv@mailo.com>
---

Please Note: The proposed change is compile tested only. I am unable to perform
device based testing in the absence of the hardware, both the RasPi board and the
Pi433 device. Please let me know if it is necessary for me to test such patches
on the real device myself. I will stop sending the patches till I have the hardware
to test them. Thanks.



 drivers/staging/pi433/rf69.c | 7 +++++++
 1 file changed, 7 insertions(+)

--
2.34.1
  

Comments

Greg KH Nov. 22, 2022, 12:08 p.m. UTC | #1
On Sun, Nov 20, 2022 at 01:24:21AM +0530, Deepak R Varma wrote:
> The DCCFreq value is used to obtain the DC offset canceller cut-off
> frequency. Upon device power reset, the bits 7-5 of the RegRxBw register
> that represent the DCCFreq setting are set to 0x4, which evaluates the
> cut-off frequency to be 1% of RxBw.
> 
> In the current implementation, first, there is no configuration variable
> defined in the struct pi433_rx_cfg for the user to set this value as
> part of the UAPI. Second, the code simply ignores the value of DCC
> setting and allows it to never change.
> 
> As per the RFM69HCW tech specs, the default value for DCC frequency is
> recommended to be 4% of the RxBw; which requires the DCC setting bits
> to be set to 010. So allow the DCC setting to change to recommended /
> default value for improved rx sensitivity.
> 
> Signed-off-by: Deepak R Varma <drv@mailo.com>
> ---
> 
> Please Note: The proposed change is compile tested only. I am unable to perform
> device based testing in the absence of the hardware, both the RasPi board and the
> Pi433 device. Please let me know if it is necessary for me to test such patches
> on the real device myself. I will stop sending the patches till I have the hardware
> to test them. Thanks.

For changes like this, you need to test it on the device itself.

thanks,

greg k-h
  

Patch

diff --git a/drivers/staging/pi433/rf69.c b/drivers/staging/pi433/rf69.c
index 8c7fab6a46bb..8468d4717dd0 100644
--- a/drivers/staging/pi433/rf69.c
+++ b/drivers/staging/pi433/rf69.c
@@ -465,6 +465,13 @@  static int rf69_set_bandwidth_intern(struct spi_device *spi, u8 reg,
 	// read old value
 	bandwidth = rf69_read_reg(spi, reg);

+	/* DCC setting bits [7-5] are set to 0x4 on reset. Since there is no user
+	 * input available in the rx config struct, we should set it to default
+	 * or the recommended value as per the technical specification.
+	 */
+	if ((bandwidth >> 5) == 0x4)
+		bandwidth = bandwidth & BW_DCC_4_PERCENT;
+
 	// "delete" mantisse and exponent = just keep the DCC setting
 	bandwidth = bandwidth & MASK_BW_DCC_FREQ;