[v2,3/3] arm64: dts: qcom: sc8280xp: Add soundcard support

Message ID 20221119164425.86014-4-srinivas.kandagatla@linaro.org
State New
Headers
Series arm64: dts: qcom: sc8280xp: add audio support |

Commit Message

Srinivas Kandagatla Nov. 19, 2022, 4:44 p.m. UTC
  Add support for SoundCard on X13s. This patch adds support for Headset
Playback, record and 2 DMICs on the Panel along with the regulators
required for powering up the LPASS codecs.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
---
 .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts    | 217 ++++++++++++++++++
 1 file changed, 217 insertions(+)
  

Comments

Johan Hovold Nov. 21, 2022, 8:02 a.m. UTC | #1
On Sat, Nov 19, 2022 at 04:44:25PM +0000, Srinivas Kandagatla wrote:
> Add support for SoundCard on X13s. This patch adds support for Headset
> Playback, record and 2 DMICs on the Panel along with the regulators
> required for powering up the LPASS codecs.

Subject prefix should include "x13s":

	arm64: dts: qcom: sc8280xp-x13s: ...

> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---
>  .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts    | 217 ++++++++++++++++++
>  1 file changed, 217 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> index b2b744bb8a53..f1f93fc4fa2d 100644
> --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts

> @@ -346,6 +378,163 @@ edp_bl_pwm: edp-bl-pwm-state {
>  	};
>  };
>  
> +&soc {
> +	wcd938x: codec {
> +		compatible = "qcom,wcd9380-codec";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&wcd_default>;
> +		reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
> +		#sound-dai-cells = <1>;
> +
> +		vdd-buck-supply = <&vreg_s10b>;
> +		vdd-rxtx-supply = <&vreg_s10b>;
> +		vdd-io-supply = <&vreg_s10b>;
> +		vdd-mic-bias-supply = <&vreg_bob>;
> +		qcom,micbias1-microvolt = <1800000>;
> +		qcom,micbias2-microvolt = <1800000>;
> +		qcom,micbias3-microvolt = <1800000>;
> +		qcom,micbias4-microvolt = <1800000>;
> +		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
> +		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
> +		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
> +		qcom,rx-device = <&wcd_rx>;
> +		qcom,tx-device = <&wcd_tx>;
> +	};
> +};

Please move all the sound nodes above the "/* PINCTRL */" marker and try
to maintain the sort order (by node name).

> +
> +&sound {

...

> +};
> +
> +&swr0 {
> +	left_spkr: wsa8830-left@0,1 {
> +		compatible = "sdw10217020200";
> +		reg = <0 1>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&spkr_1_sd_n_default>;
> +		powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>;
> +		#thermal-sensor-cells = <0>;
> +		sound-name-prefix = "SpkrLeft";
> +		#sound-dai-cells = <0>;
> +		vdd-supply = <&vreg_s10b>;
> +	};
> +
> +	right_spkr: wsa8830-right@0,2{
> +		compatible = "sdw10217020200";
> +		reg = <0 2>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&spkr_2_sd_n_default>;
> +		powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
> +		#thermal-sensor-cells = <0>;
> +		sound-name-prefix = "SpkrRight";
> +		#sound-dai-cells = <0>;
> +		vdd-supply = <&vreg_s10b>;
> +	};
> +};
> +
> +

Stray newline.

> +&swr1 {
> +	status = "okay";
> +
> +	wcd_rx: wcd9380-rx@0,4 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 4>;
> +		qcom,rx-port-mapping = <1 2 3 4 5 6>;
> +

Stray newline.

> +	};
> +};
> +
> +&swr2 {
> +	status = "okay";
> +
> +	wcd_tx: wcd9380-tx@0,3 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 3>;
> +		qcom,tx-port-mapping = <1 1 2 3>;
> +	};
> +};
> +
> +&vamacro {
> +	pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
> +	pinctrl-names = "default";
> +	vdd-micb-supply = <&vreg_s10b>;
> +	qcom,dmic-sample-rate = <600000>;
> +};
> +
>  &tlmm {
>  	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>  
> @@ -369,6 +558,14 @@ reset {
>  		};
>  	};
>  
> +	wcd_default: wcd-default-state {
> +		reset-pins {
> +			pins = "gpio106";
> +			function = "gpio";
> +			bias-disable;
> +		};
> +	};
> +

Please try to keep the nodes sorted by name (i.e. move it last).

>  	qup0_i2c4_default: qup0-i2c4-default-state {
>  		pins = "gpio171", "gpio172";
>  		function = "qup4";
> @@ -383,6 +580,26 @@ qup2_i2c5_default: qup2-i2c5-default-state {
>  		drive-strength = <16>;
>  	};
>  
> +	spkr_1_sd_n_default: spkr-1-sd-n-default-state {
> +		perst-n-pins {
> +			pins = "gpio178";
> +			function = "gpio";
> +			drive-strength = <16>;
> +			bias-disable;
> +			output-high;
> +		};
> +	};
> +
> +	spkr_2_sd_n_default: spkr-2-sd-n-default-state {
> +		perst-n-pins {
> +			pins = "gpio179";
> +			function = "gpio";
> +			drive-strength = <16>;
> +			bias-disable;
> +			output-high;
> +		};
> +	};
> +
>  	tpad_default: tpad-default-state {
>  		int-n {
>  			pins = "gpio182";

Johan
  
Krzysztof Kozlowski Nov. 21, 2022, 8:34 a.m. UTC | #2
On 19/11/2022 17:44, Srinivas Kandagatla wrote:
> Add support for SoundCard on X13s. This patch adds support for Headset
> Playback, record and 2 DMICs on the Panel along with the regulators
> required for powering up the LPASS codecs.
> 
> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
> ---

Thank you for your patch. There is something to discuss/improve.

> +	right_spkr: wsa8830-right@0,2{
> +		compatible = "sdw10217020200";
> +		reg = <0 2>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&spkr_2_sd_n_default>;
> +		powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
> +		#thermal-sensor-cells = <0>;
> +		sound-name-prefix = "SpkrRight";
> +		#sound-dai-cells = <0>;
> +		vdd-supply = <&vreg_s10b>;
> +	};
> +};
> +
> +

Only one blank line.

> +&swr1 {
> +	status = "okay";
> +
> +	wcd_rx: wcd9380-rx@0,4 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 4>;
> +		qcom,rx-port-mapping = <1 2 3 4 5 6>;

No improvements: Still looks too long.

> +

Drop empty line.
> +	};
> +};
> +
> +&swr2 {
> +	status = "okay";
> +
> +	wcd_tx: wcd9380-tx@0,3 {
> +		compatible = "sdw20217010d00";
> +		reg = <0 3>;
> +		qcom,tx-port-mapping = <1 1 2 3>;
> +	};
> +};
> +
> +&vamacro {
> +	pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
> +	pinctrl-names = "default";
> +	vdd-micb-supply = <&vreg_s10b>;
> +	qcom,dmic-sample-rate = <600000>;
> +};
> +
>  &tlmm {
>  	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>  
> @@ -369,6 +558,14 @@ reset {
>  		};
>  	};
>  
> +	wcd_default: wcd-default-state {
> +		reset-pins {
> +			pins = "gpio106";
> +			function = "gpio";
> +			bias-disable;
> +		};
> +	};
> +
>  	qup0_i2c4_default: qup0-i2c4-default-state {
>  		pins = "gpio171", "gpio172";
>  		function = "qup4";
> @@ -383,6 +580,26 @@ qup2_i2c5_default: qup2-i2c5-default-state {
>  		drive-strength = <16>;
>  	};
>  
> +	spkr_1_sd_n_default: spkr-1-sd-n-default-state {
> +		perst-n-pins {
> +			pins = "gpio178";
> +			function = "gpio";
> +			drive-strength = <16>;
> +			bias-disable;
> +			output-high;
> +		};
> +	};
> +
> +	spkr_2_sd_n_default: spkr-2-sd-n-default-state {
> +		perst-n-pins {
> +			pins = "gpio179";
> +			function = "gpio";
> +			drive-strength = <16>;
> +			bias-disable;
> +			output-high;
> +		};
> +	};
> +
>  	tpad_default: tpad-default-state {
>  		int-n {

This won't apply cleanly. You need to base your patches on recent trees.

Best regards,
Krzysztof
  
Srinivas Kandagatla Nov. 21, 2022, 11:08 a.m. UTC | #3
Thanks Krzysztof,

On 21/11/2022 08:34, Krzysztof Kozlowski wrote:
> On 19/11/2022 17:44, Srinivas Kandagatla wrote:
>> Add support for SoundCard on X13s. This patch adds support for Headset
>> Playback, record and 2 DMICs on the Panel along with the regulators
>> required for powering up the LPASS codecs.
>>
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> ---
> 
> Thank you for your patch. There is something to discuss/improve.
> 
>> +	right_spkr: wsa8830-right@0,2{
>> +		compatible = "sdw10217020200";
>> +		reg = <0 2>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&spkr_2_sd_n_default>;
>> +		powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
>> +		#thermal-sensor-cells = <0>;
>> +		sound-name-prefix = "SpkrRight";
>> +		#sound-dai-cells = <0>;
>> +		vdd-supply = <&vreg_s10b>;
>> +	};
>> +};
>> +
>> +
> 
> Only one blank line.
> 
>> +&swr1 {
>> +	status = "okay";
>> +
>> +	wcd_rx: wcd9380-rx@0,4 {
>> +		compatible = "sdw20217010d00";
>> +		reg = <0 4>;
>> +		qcom,rx-port-mapping = <1 2 3 4 5 6>;
> 
> No improvements: Still looks too long.
Yep we only have 5 out ports.

> 
>> +
> 
> Drop empty line.

Looks like I had to many stray lines :-)

will fix this in next spin.

>> +	};
>> +};
>> +
>> +&swr2 {
>> +	status = "okay";
>> +
>> +	wcd_tx: wcd9380-tx@0,3 {
>> +		compatible = "sdw20217010d00";
>> +		reg = <0 3>;
>> +		qcom,tx-port-mapping = <1 1 2 3>;
>> +	};
>> +};
>> +
>> +&vamacro {
>> +	pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
>> +	pinctrl-names = "default";
>> +	vdd-micb-supply = <&vreg_s10b>;
>> +	qcom,dmic-sample-rate = <600000>;
>> +};
>> +
>>   &tlmm {
>>   	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>>   
>> @@ -369,6 +558,14 @@ reset {
>>   		};
>>   	};
>>   
>> +	wcd_default: wcd-default-state {
>> +		reset-pins {
>> +			pins = "gpio106";
>> +			function = "gpio";
>> +			bias-disable;
>> +		};
>> +	};
>> +
>>   	qup0_i2c4_default: qup0-i2c4-default-state {
>>   		pins = "gpio171", "gpio172";
>>   		function = "qup4";
>> @@ -383,6 +580,26 @@ qup2_i2c5_default: qup2-i2c5-default-state {
>>   		drive-strength = <16>;
>>   	};
>>   
>> +	spkr_1_sd_n_default: spkr-1-sd-n-default-state {
>> +		perst-n-pins {
>> +			pins = "gpio178";
>> +			function = "gpio";
>> +			drive-strength = <16>;
>> +			bias-disable;
>> +			output-high;
>> +		};
>> +	};
>> +
>> +	spkr_2_sd_n_default: spkr-2-sd-n-default-state {
>> +		perst-n-pins {
>> +			pins = "gpio179";
>> +			function = "gpio";
>> +			drive-strength = <16>;
>> +			bias-disable;
>> +			output-high;
>> +		};
>> +	};
>> +
>>   	tpad_default: tpad-default-state {
>>   		int-n {
> 
> This won't apply cleanly. You need to base your patches on recent trees.

Yes, I will rebase this on top of 
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/log/?h=arm64-for-6.2

--srini
> 
> Best regards,
> Krzysztof
>
  
Srinivas Kandagatla Nov. 21, 2022, 11:34 a.m. UTC | #4
Thanks Johan,

On 21/11/2022 08:02, Johan Hovold wrote:
> On Sat, Nov 19, 2022 at 04:44:25PM +0000, Srinivas Kandagatla wrote:
>> Add support for SoundCard on X13s. This patch adds support for Headset
>> Playback, record and 2 DMICs on the Panel along with the regulators
>> required for powering up the LPASS codecs.
> 
> Subject prefix should include "x13s":
> 
> 	arm64: dts: qcom: sc8280xp-x13s: ...
> 
>> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> ---
>>   .../qcom/sc8280xp-lenovo-thinkpad-x13s.dts    | 217 ++++++++++++++++++
>>   1 file changed, 217 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
>> index b2b744bb8a53..f1f93fc4fa2d 100644
>> --- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
>> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
> 
>> @@ -346,6 +378,163 @@ edp_bl_pwm: edp-bl-pwm-state {
>>   	};
>>   };
>>   
>> +&soc {
>> +	wcd938x: codec {
>> +		compatible = "qcom,wcd9380-codec";
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&wcd_default>;
>> +		reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
>> +		#sound-dai-cells = <1>;
>> +
>> +		vdd-buck-supply = <&vreg_s10b>;
>> +		vdd-rxtx-supply = <&vreg_s10b>;
>> +		vdd-io-supply = <&vreg_s10b>;
>> +		vdd-mic-bias-supply = <&vreg_bob>;
>> +		qcom,micbias1-microvolt = <1800000>;
>> +		qcom,micbias2-microvolt = <1800000>;
>> +		qcom,micbias3-microvolt = <1800000>;
>> +		qcom,micbias4-microvolt = <1800000>;
>> +		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
>> +		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
>> +		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
>> +		qcom,rx-device = <&wcd_rx>;
>> +		qcom,tx-device = <&wcd_tx>;
>> +	};
>> +};
> 
> Please move all the sound nodes above the "/* PINCTRL */" marker and try
> to maintain the sort order (by node name).

Yes, I did miss this indeed, its now fixed in v3.

Will send v3 along with other fixes.

--srini
> 
>> +
>> +&sound {
> 
> ...
> 
>> +};
>> +
>> +&swr0 {
>> +	left_spkr: wsa8830-left@0,1 {
>> +		compatible = "sdw10217020200";
>> +		reg = <0 1>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&spkr_1_sd_n_default>;
>> +		powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>;
>> +		#thermal-sensor-cells = <0>;
>> +		sound-name-prefix = "SpkrLeft";
>> +		#sound-dai-cells = <0>;
>> +		vdd-supply = <&vreg_s10b>;
>> +	};
>> +
>> +	right_spkr: wsa8830-right@0,2{
>> +		compatible = "sdw10217020200";
>> +		reg = <0 2>;
>> +		pinctrl-names = "default";
>> +		pinctrl-0 = <&spkr_2_sd_n_default>;
>> +		powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
>> +		#thermal-sensor-cells = <0>;
>> +		sound-name-prefix = "SpkrRight";
>> +		#sound-dai-cells = <0>;
>> +		vdd-supply = <&vreg_s10b>;
>> +	};
>> +};
>> +
>> +
> 
> Stray newline.
> 
>> +&swr1 {
>> +	status = "okay";
>> +
>> +	wcd_rx: wcd9380-rx@0,4 {
>> +		compatible = "sdw20217010d00";
>> +		reg = <0 4>;
>> +		qcom,rx-port-mapping = <1 2 3 4 5 6>;
>> +
> 
> Stray newline.
> 
>> +	};
>> +};
>> +
>> +&swr2 {
>> +	status = "okay";
>> +
>> +	wcd_tx: wcd9380-tx@0,3 {
>> +		compatible = "sdw20217010d00";
>> +		reg = <0 3>;
>> +		qcom,tx-port-mapping = <1 1 2 3>;
>> +	};
>> +};
>> +
>> +&vamacro {
>> +	pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
>> +	pinctrl-names = "default";
>> +	vdd-micb-supply = <&vreg_s10b>;
>> +	qcom,dmic-sample-rate = <600000>;
>> +};
>> +
>>   &tlmm {
>>   	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
>>   
>> @@ -369,6 +558,14 @@ reset {
>>   		};
>>   	};
>>   
>> +	wcd_default: wcd-default-state {
>> +		reset-pins {
>> +			pins = "gpio106";
>> +			function = "gpio";
>> +			bias-disable;
>> +		};
>> +	};
>> +
> 
> Please try to keep the nodes sorted by name (i.e. move it last).
> 
>>   	qup0_i2c4_default: qup0-i2c4-default-state {
>>   		pins = "gpio171", "gpio172";
>>   		function = "qup4";
>> @@ -383,6 +580,26 @@ qup2_i2c5_default: qup2-i2c5-default-state {
>>   		drive-strength = <16>;
>>   	};
>>   
>> +	spkr_1_sd_n_default: spkr-1-sd-n-default-state {
>> +		perst-n-pins {
>> +			pins = "gpio178";
>> +			function = "gpio";
>> +			drive-strength = <16>;
>> +			bias-disable;
>> +			output-high;
>> +		};
>> +	};
>> +
>> +	spkr_2_sd_n_default: spkr-2-sd-n-default-state {
>> +		perst-n-pins {
>> +			pins = "gpio179";
>> +			function = "gpio";
>> +			drive-strength = <16>;
>> +			bias-disable;
>> +			output-high;
>> +		};
>> +	};
>> +
>>   	tpad_default: tpad-default-state {
>>   		int-n {
>>   			pins = "gpio182";
> 
> Johan
  

Patch

diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
index b2b744bb8a53..f1f93fc4fa2d 100644
--- a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
@@ -58,6 +58,16 @@  vreg_misc_3p3: regulator-misc-3p3 {
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	vreg_vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "VPH_VCC3R9";
+		regulator-min-microvolt = <3900000>;
+		regulator-max-microvolt = <3900000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &apps_rsc {
@@ -67,6 +77,13 @@  pmc8280-1-rpmh-regulators {
 
 		vdd-l3-l5-supply = <&vreg_s11b>;
 
+		vreg_s10b: smps10 {
+			regulator-name = "vreg_s10b";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
 		vreg_s11b: smps11 {
 			regulator-name = "vreg_s11b";
 			regulator-min-microvolt = <1272000>;
@@ -74,6 +91,13 @@  vreg_s11b: smps11 {
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
+		vreg_s12b: smps12 {
+			regulator-name = "vreg_s12b";
+			regulator-min-microvolt = <984000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
 		vreg_l3b: ldo3 {
 			regulator-name = "vreg_l3b";
 			regulator-min-microvolt = <1200000>;
@@ -102,6 +126,7 @@  vreg_l6b: ldo6 {
 	pmc8280c-rpmh-regulators {
 		compatible = "qcom,pm8350c-rpmh-regulators";
 		qcom,pmic-id = "c";
+		vdd-bob-supply = <&vreg_vph_pwr>;
 
 		vreg_l1c: ldo1 {
 			regulator-name = "vreg_l1c";
@@ -123,6 +148,13 @@  vreg_l13c: ldo13 {
 			regulator-max-microvolt = <3072000>;
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
+
+		vreg_bob: bob {
+			regulator-name = "vreg_bob";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
 	};
 
 	pmc8280-2-rpmh-regulators {
@@ -346,6 +378,163 @@  edp_bl_pwm: edp-bl-pwm-state {
 	};
 };
 
+&soc {
+	wcd938x: codec {
+		compatible = "qcom,wcd9380-codec";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wcd_default>;
+		reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <1>;
+
+		vdd-buck-supply = <&vreg_s10b>;
+		vdd-rxtx-supply = <&vreg_s10b>;
+		vdd-io-supply = <&vreg_s10b>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+	};
+};
+
+&sound {
+	compatible = "qcom,sc8280xp-sndcard";
+	model = "SC8280XP-LENOVO-X13S";
+	audio-routing =
+		"SpkrLeft IN", "WSA_SPK1 OUT",
+		"SpkrRight IN", "WSA_SPK2 OUT",
+		"IN1_HPHL", "HPHL_OUT",
+		"IN2_HPHR", "HPHR_OUT",
+		"AMIC2", "MIC BIAS2",
+		"VA DMIC0", "MIC BIAS1",
+		"VA DMIC1", "MIC BIAS1",
+		"VA DMIC2", "MIC BIAS3",
+		"TX DMIC0", "MIC BIAS1",
+		"TX DMIC1", "MIC BIAS2",
+		"TX DMIC2", "MIC BIAS3",
+		"TX SWR_ADC1", "ADC2_OUTPUT";
+
+	wcd-playback-dai-link {
+		link-name = "WCD Playback";
+		cpu {
+			sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+		};
+
+		codec {
+			sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+	};
+
+	wcd-capture-dai-link {
+		link-name = "WCD Capture";
+		cpu {
+			sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+		};
+
+		codec {
+			sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+	};
+
+	wsa-dai-link {
+		link-name = "WSA Playback";
+		cpu {
+			sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+		};
+
+		codec {
+			sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+	};
+
+	va-dai-link {
+		link-name = "VA Capture";
+		cpu {
+			sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+		};
+
+		platform {
+			sound-dai = <&q6apm>;
+		};
+
+		codec {
+			sound-dai = <&vamacro 0>;
+		};
+	};
+};
+
+&swr0 {
+	left_spkr: wsa8830-left@0,1 {
+		compatible = "sdw10217020200";
+		reg = <0 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spkr_1_sd_n_default>;
+		powerdown-gpios = <&tlmm 178 GPIO_ACTIVE_LOW>;
+		#thermal-sensor-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		#sound-dai-cells = <0>;
+		vdd-supply = <&vreg_s10b>;
+	};
+
+	right_spkr: wsa8830-right@0,2{
+		compatible = "sdw10217020200";
+		reg = <0 2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&spkr_2_sd_n_default>;
+		powerdown-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
+		#thermal-sensor-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		#sound-dai-cells = <0>;
+		vdd-supply = <&vreg_s10b>;
+	};
+};
+
+
+&swr1 {
+	status = "okay";
+
+	wcd_rx: wcd9380-rx@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5 6>;
+
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	wcd_tx: wcd9380-tx@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <1 1 2 3>;
+	};
+};
+
+&vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
+	pinctrl-names = "default";
+	vdd-micb-supply = <&vreg_s10b>;
+	qcom,dmic-sample-rate = <600000>;
+};
+
 &tlmm {
 	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
 
@@ -369,6 +558,14 @@  reset {
 		};
 	};
 
+	wcd_default: wcd-default-state {
+		reset-pins {
+			pins = "gpio106";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
 	qup0_i2c4_default: qup0-i2c4-default-state {
 		pins = "gpio171", "gpio172";
 		function = "qup4";
@@ -383,6 +580,26 @@  qup2_i2c5_default: qup2-i2c5-default-state {
 		drive-strength = <16>;
 	};
 
+	spkr_1_sd_n_default: spkr-1-sd-n-default-state {
+		perst-n-pins {
+			pins = "gpio178";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	spkr_2_sd_n_default: spkr-2-sd-n-default-state {
+		perst-n-pins {
+			pins = "gpio179";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+			output-high;
+		};
+	};
+
 	tpad_default: tpad-default-state {
 		int-n {
 			pins = "gpio182";