[v3,6/9] arm64: dts: mediatek: Add MT8186 Krabby platform based Tentacruel / Tentacool
Commit Message
Tentacruel and Tentacool are MT8186 based Chromebooks based on the
Krabby design.
Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
convertible device with touchscreen and stylus.
Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
device. It does not have a touchscreen or stylus.
The two devices both have two variants. The difference is a second
source touchpad controller that shares the same address as the original,
but is incompatible.
The extra SKU IDs for the Tentacruel devices map to different sensor
components attached to the Embedded Controller. These are not visible
to the main processor.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
---
Changes since v2:
- Picked up Conor's ack
- Rename touchpad to trackpad
- Drop pinctrl properties from trackpad in tentacruel/tentacool second
source trackpad
Changes since v1:
- Reorder SKU numbers in descending order.
- Fixed pinconfig node names
- Moved pinctrl-* properties after interrupts-*
- Switched to interrupts-extended for external components
- Marked ADSP as explicitly disabled, with a comment explaining that it
stalls the system
- Renamed "touchpad" to "trackpad"
- Dropped bogus "no-laneswap" property from it6505 node
- Moved "realtek,jd-src" property to after all the regulator supplies
- Switched to macros for MT6366 regulator "regulator-allowed-modes"
- Renamed "vgpu" regulator name to allow coupling, with a comment
containing the name used in the design
- Renamed "cr50" node name to "tpm"
- Moved trackpad_pins reference up to i2c2; workaround for second source
component resource sharing.
- Fix copyright year
- Fixed touchscreen supply name
arch/arm64/boot/dts/mediatek/Makefile | 4 +
.../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
.../mt8186-corsola-tentacool-sku327681.dts | 57 +
.../mt8186-corsola-tentacool-sku327683.dts | 24 +
.../mt8186-corsola-tentacruel-sku262144.dts | 44 +
.../mt8186-corsola-tentacruel-sku262148.dts | 26 +
.../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
7 files changed, 2003 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
Comments
Hello Chen-Yu,
On 12/4/23 10:40, Chen-Yu Tsai wrote:
> Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> Krabby design.
>
> Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> convertible device with touchscreen and stylus.
>
> Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> device. It does not have a touchscreen or stylus.
>
> The two devices both have two variants. The difference is a second
> source touchpad controller that shares the same address as the original,
> but is incompatible.
>
> The extra SKU IDs for the Tentacruel devices map to different sensor
> components attached to the Embedded Controller. These are not visible
> to the main processor.
>
> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> ---
> Changes since v2:
> - Picked up Conor's ack
> - Rename touchpad to trackpad
> - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> source trackpad
>
> Changes since v1:
> - Reorder SKU numbers in descending order.
> - Fixed pinconfig node names
> - Moved pinctrl-* properties after interrupts-*
> - Switched to interrupts-extended for external components
> - Marked ADSP as explicitly disabled, with a comment explaining that it
> stalls the system
> - Renamed "touchpad" to "trackpad"
> - Dropped bogus "no-laneswap" property from it6505 node
> - Moved "realtek,jd-src" property to after all the regulator supplies
> - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> - Renamed "vgpu" regulator name to allow coupling, with a comment
> containing the name used in the design
> - Renamed "cr50" node name to "tpm"
> - Moved trackpad_pins reference up to i2c2; workaround for second source
> component resource sharing.
> - Fix copyright year
> - Fixed touchscreen supply name
>
> arch/arm64/boot/dts/mediatek/Makefile | 4 +
> .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
> 7 files changed, 2003 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index e6e7592a3645..442af61b1305 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> new file mode 100644
> index 000000000000..9b2b64525961
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> @@ -0,0 +1,129 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2022 Google LLC
> + */
> +
> +/dts-v1/;
> +#include "mt8186-corsola.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + aliases {
> + i2c4 = &i2c4;
> + };
> +};
> +
> +&dsi_out {
> + remote-endpoint = <&ps8640_in>;
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> +
> + ps8640: edp-bridge@8 {
> + compatible = "parade,ps8640";
> + reg = <0x8>;
> + powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ps8640_pins>;
> + vdd12-supply = <&mt6366_vrf12_reg>;
> + vdd33-supply = <&mt6366_vcn33_reg>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + ps8640_in: endpoint {
> + remote-endpoint = <&dsi_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + ps8640_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +
> + aux-bus {
> + panel {
> + compatible = "edp-panel";
> + power-supply = <&pp3300_disp_x>;
> + backlight = <&backlight_lcd0>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&ps8640_out>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c1 {
> + i2c-scl-internal-delay-ns = <10000>;
> +
> + touchscreen: touchscreen@10 {
> + compatible = "hid-over-i2c";
> + reg = <0x10>;
> + interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&touchscreen_pins>;
> + post-power-on-delay-ms = <10>;
> + hid-descr-addr = <0x0001>;
> + vdd-supply = <&pp3300_s3>;
> + };
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4_pins>;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + proximity@28 {
> + compatible = "semtech,sx9324";
> + reg = <0x28>;
> + interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sar_sensor_pins>;
> + vdd-supply = <&mt6366_vio18_reg>;
> + svdd-supply = <&mt6366_vio18_reg>;
> + #io-channel-cells = <1>;
> + };
> +};
> +
> +&pio {
> + i2c4_pins: i2c4-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
> + <PINMUX_GPIO135__FUNC_SCL4>;
> + bias-disable;
> + drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
> + ps8640_pins: ps8640-pins {
> + pins-pwrdn-rst {
> + pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
> + <PINMUX_GPIO98__FUNC_GPIO98>;
> + output-low;
> + };
> + };
> +
> + sar_sensor_pins: sar-sensor-pins {
> + pins-irq {
> + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> new file mode 100644
> index 000000000000..9bb64353ca65
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> @@ -0,0 +1,57 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2022 Google LLC
> + */
> +
> +/dts-v1/;
> +#include "mt8186-corsola-krabby.dtsi"
> +
> +/ {
> + model = "Google Tentacool board";
> + compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
> + chassis-type = "laptop";
> +};
> +
> +/* Tentacool omits the pen. */
> +&gpio_keys {
> + status = "disabled";
> +};
> +
> +/* Tentacool omits the touchscreen; nothing else is on i2c1. */
> +&i2c1 {
> + status = "disabled";
> +};
> +
> +&keyboard_controller {
> + function-row-physmap = <
> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> + >;
> +
> + linux,keymap = <
> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> + CROS_STD_MAIN_KEYMAP
> + >;
> +};
> +
> +/* Tentacool omits the touchscreen. */
> +&touchscreen {
> + status = "disabled";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> new file mode 100644
> index 000000000000..c3ae6f9616c8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2023 Google LLC
> + */
> +
> +#include "mt8186-corsola-tentacool-sku327681.dts"
> +
> +/ {
> + compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
> +};
> +
> +/* This variant replaces only the trackpad controller. */
> +&i2c2 {
> + /delete-node/ trackpad@15;
> +
> + trackpad@15 {
> + compatible = "hid-over-i2c";
> + reg = <0x15>;
> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> + hid-descr-addr = <0x0001>;
> + vdd-supply = <&pp3300_s3>;
> + wakeup-source;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> new file mode 100644
> index 000000000000..26d3451a5e47
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> @@ -0,0 +1,44 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2022 Google LLC
> + */
> +
> +/dts-v1/;
> +#include "mt8186-corsola-krabby.dtsi"
> +
> +/ {
> + model = "Google Tentacruel board";
> + compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
> + "google,tentacruel-sku262145", "google,tentacruel-sku262144",
> + "google,tentacruel", "mediatek,mt8186";
> + chassis-type = "convertible";
> +};
> +
> +&keyboard_controller {
> + function-row-physmap = <
> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> + >;
> +
> + linux,keymap = <
> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> + CROS_STD_MAIN_KEYMAP
> + >;
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> new file mode 100644
> index 000000000000..447b57b12b41
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2023 Google LLC
> + */
> +
> +#include "mt8186-corsola-tentacruel-sku262144.dts"
> +
> +/ {
> + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
> + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
> + "google,tentacruel", "mediatek,mt8186";
> +};
> +
> +/* This variant replaces only the trackpad controller. */
> +&i2c2 {
> + /delete-node/ trackpad@15;
> +
> + trackpad@15 {
> + compatible = "hid-over-i2c";
> + reg = <0x15>;
> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> + hid-descr-addr = <0x0001>;
> + vdd-supply = <&pp3300_s3>;
> + wakeup-source;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> new file mode 100644
> index 000000000000..8726b2916ef1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> @@ -0,0 +1,1719 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2022 MediaTek Inc.
> + */
> +/dts-v1/;
> +#include "mt8186.dtsi"
> +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
> +
> +/ {
> + aliases {
> + i2c0 = &i2c0;
> + i2c1 = &i2c1;
> + i2c2 = &i2c2;
> + i2c3 = &i2c3;
> + i2c5 = &i2c5;
> + mmc0 = &mmc0;
> + mmc1 = &mmc1;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + /* The size should be filled in by the bootloader. */
> + reg = <0 0x40000000 0 0>;
> + };
> +
> + backlight_lcd0: backlight-lcd0 {
> + compatible = "pwm-backlight";
> + pwms = <&pwm0 0 500000>;
> + power-supply = <&ppvar_sys>;
> + enable-gpios = <&pio 152 0>;
> + brightness-levels = <0 1023>;
> + num-interpolated-steps = <1023>;
> + default-brightness-level = <576>;
> + };
> +
> + btsco: bt-sco {
> + compatible = "linux,bt-sco";
> + #sound-dai-cells = <0>;
> + };
> +
> + dmic_codec: dmic-codec {
> + compatible = "dmic-codec";
> + num-channels = <2>;
> + wakeup-delay-ms = <50>;
> + #sound-dai-cells = <0>;
> + };
> +
> + gpio_keys: gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pen_eject>;
> +
> + pen_insert: pen-insert-switch {
> + label = "Pen Insert";
> + /* Insert = low, eject = high */
> + gpios = <&pio 18 GPIO_ACTIVE_LOW>;
> + linux,code = <SW_PEN_INSERTED>;
> + linux,input-type = <EV_SW>;
> + wakeup-event-action = <EV_ACT_DEASSERTED>;
> + wakeup-source;
> + };
> + };
> +
> + pp1800_dpbrdg_dx: regulator-pp1800-dpbrdg-dx {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&en_pp1800_dpbrdg>;
> + regulator-name = "pp1800_dpbrdg_dx";
> + enable-active-high;
> + gpio = <&pio 39 GPIO_ACTIVE_HIGH>;
> + vin-supply = <&mt6366_vio18_reg>;
> + };
> +
> + pp3300_disp_x: regulator-pp3300-disp-x {
> + compatible = "regulator-fixed";
> + regulator-name = "pp3300_disp_x";
> + pinctrl-names = "default";
> + pinctrl-0 = <&edp_panel_fixed_pins>;
> + enable-active-high;
> + regulator-boot-on;
> + gpio = <&pio 153 GPIO_ACTIVE_HIGH>;
> + vin-supply = <&pp3300_z2>;
> + };
> +
> + /* system wide LDO 3.3V power rail */
> + pp3300_z5: regulator-pp3300-ldo-z5 {
> + compatible = "regulator-fixed";
> + regulator-name = "pp3300_ldo_z5";
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ppvar_sys>;
> + };
> +
> + /* separately switched 3.3V power rail */
> + pp3300_s3: regulator-pp3300-s3 {
> + compatible = "regulator-fixed";
> + regulator-name = "pp3300_s3";
> + /* automatically sequenced by PMIC EXT_PMIC_EN2 */
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&pp3300_z2>;
> + };
> +
> + /* system wide 3.3V power rail */
> + pp3300_z2: regulator-pp3300-z2 {
> + compatible = "regulator-fixed";
> + regulator-name = "pp3300_z2";
> + /* EN pin tied to pp4200_z2, which is controlled by EC */
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + vin-supply = <&ppvar_sys>;
> + };
> +
> + /* system wide 4.2V power rail */
> + pp4200_z2: regulator-pp4200-z2 {
> + compatible = "regulator-fixed";
> + regulator-name = "pp4200_z2";
> + /* controlled by EC */
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <4200000>;
> + regulator-max-microvolt = <4200000>;
> + vin-supply = <&ppvar_sys>;
> + };
> +
> + /* system wide switching 5.0V power rail */
> + pp5000_z2: regulator-pp5000-z2 {
> + compatible = "regulator-fixed";
> + regulator-name = "pp5000_z2";
> + /* controlled by EC */
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + vin-supply = <&ppvar_sys>;
> + };
> +
> + /* system wide semi-regulated power rail from battery or USB */
> + ppvar_sys: regulator-ppvar-sys {
> + compatible = "regulator-fixed";
> + regulator-name = "ppvar_sys";
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + reserved_memory: reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + adsp_dma_mem: memory@61000000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0x61000000 0 0x100000>;
> + no-map;
> + };
> +
> + adsp_mem: memory@60000000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0x60000000 0 0xA00000>;
> + no-map;
> + };
> +
> + scp_mem: memory@50000000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0x50000000 0 0x10a0000>;
> + no-map;
> + };
> + };
> +
> + sound: sound {
> + compatible = "mediatek,mt8186-mt6366-rt1019-rt5682s-sound";
> + pinctrl-names = "aud_clk_mosi_off",
> + "aud_clk_mosi_on",
> + "aud_clk_miso_off",
> + "aud_clk_miso_on",
> + "aud_dat_miso_off",
> + "aud_dat_miso_on",
> + "aud_dat_mosi_off",
> + "aud_dat_mosi_on",
> + "aud_gpio_i2s0_off",
> + "aud_gpio_i2s0_on",
> + "aud_gpio_i2s1_off",
> + "aud_gpio_i2s1_on",
> + "aud_gpio_i2s2_off",
> + "aud_gpio_i2s2_on",
> + "aud_gpio_i2s3_off",
> + "aud_gpio_i2s3_on",
> + "aud_gpio_tdm_off",
> + "aud_gpio_tdm_on",
> + "aud_gpio_pcm_off",
> + "aud_gpio_pcm_on",
> + "aud_gpio_dmic_sec";
> + pinctrl-0 = <&aud_clk_mosi_off>;
> + pinctrl-1 = <&aud_clk_mosi_on>;
> + pinctrl-2 = <&aud_clk_miso_off>;
> + pinctrl-3 = <&aud_clk_miso_on>;
> + pinctrl-4 = <&aud_dat_miso_off>;
> + pinctrl-5 = <&aud_dat_miso_on>;
> + pinctrl-6 = <&aud_dat_mosi_off>;
> + pinctrl-7 = <&aud_dat_mosi_on>;
> + pinctrl-8 = <&aud_gpio_i2s0_off>;
> + pinctrl-9 = <&aud_gpio_i2s0_on>;
> + pinctrl-10 = <&aud_gpio_i2s1_off>;
> + pinctrl-11 = <&aud_gpio_i2s1_on>;
> + pinctrl-12 = <&aud_gpio_i2s2_off>;
> + pinctrl-13 = <&aud_gpio_i2s2_on>;
> + pinctrl-14 = <&aud_gpio_i2s3_off>;
> + pinctrl-15 = <&aud_gpio_i2s3_on>;
> + pinctrl-16 = <&aud_gpio_tdm_off>;
> + pinctrl-17 = <&aud_gpio_tdm_on>;
These two above bring errors, as discussed
> + pinctrl-18 = <&aud_gpio_pcm_off>;
> + pinctrl-19 = <&aud_gpio_pcm_on>;
> + pinctrl-20 = <&aud_gpio_dmic_sec>;
> + mediatek,adsp = <&adsp>;
> + mediatek,platform = <&afe>;
> +
> + playback-codecs {
> + sound-dai = <&it6505dptx>, <&rt1019p>;
> + };
> +
> + headset-codec {
> + sound-dai = <&rt5682s 0>;
> + };
> + };
> +
> + rt1019p: speaker-codec {
> + compatible = "realtek,rt1019p";
> + pinctrl-names = "default";
> + pinctrl-0 = <&rt1019p_pins_default>;
> + sdb-gpios = <&pio 150 GPIO_ACTIVE_HIGH>;
> + #sound-dai-cells = <0>;
> + };
> +
> + usb_p1_vbus: regulator-usb-p1-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "vbus1";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + gpio = <&pio 148 GPIO_ACTIVE_HIGH>;
> + vin-supply = <&pp5000_z2>;
> + };
> +
> + wifi_pwrseq: wifi-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_enable_pin>;
> + post-power-on-delay-ms = <50>;
> + reset-gpios = <&pio 54 GPIO_ACTIVE_LOW>;
> + };
> +
> + wifi_wakeup: wifi-wakeup {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&wifi_wakeup_pin>;
> +
> + wowlan-event {
> + label = "Wake on WiFi";
> + gpios = <&pio 7 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WAKEUP>;
> + wakeup-source;
> + };
> + };
> +};
> +
> +&adsp {
> + memory-region = <&adsp_dma_mem>, <&adsp_mem>;
> + status = "disabled"; /* causes stall */
> +};
> +
> +&afe {
> + i2s0-share = "I2S1";
> + i2s3-share = "I2S2";
These i2sX-share are not documented.
> + status = "okay";
> +};
> +
> +&cci {
> + proc-supply = <&mt6366_vproc12_reg>;
> +};
> +
> +&cpu0 {
> + proc-supply = <&mt6366_vproc12_reg>;
> +};
> +
> +&cpu1 {
> + proc-supply = <&mt6366_vproc12_reg>;
> +};
> +
> +&cpu2 {
> + proc-supply = <&mt6366_vproc12_reg>;
> +};
> +
> +&cpu3 {
> + proc-supply = <&mt6366_vproc12_reg>;
> +};
> +
> +&cpu4 {
> + proc-supply = <&mt6366_vproc12_reg>;
> +};
> +
> +&cpu5 {
> + proc-supply = <&mt6366_vproc12_reg>;
> +};
> +
> +&cpu6 {
> + proc-supply = <&mt6366_vproc11_reg>;
> +};
> +
> +&cpu7 {
> + proc-supply = <&mt6366_vproc11_reg>;
> +};
> +
> +&dpi {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&dpi_pins_default>;
> + pinctrl-1 = <&dpi_pins_sleep>;
> + status = "okay";
> +};
> +
> +&dpi_out {
> + remote-endpoint = <&it6505_in>;
> +};
> +
> +&dsi0 {
> + status = "okay";
> +};
> +
> +&gic {
> + mediatek,broken-save-restore-fw;
> +};
> +
> +&gpu {
> + mali-supply = <&mt6366_vgpu_reg>;
> + status = "okay";
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + clock-frequency = <400000>;
> + i2c-scl-internal-delay-ns = <8000>;
> + status = "okay";
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + /*
> + * Trackpad pin put here to work around second source components
> + * sharing the pinmux in steelix designs.
> + */
> + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
While this makes things better, it's not correct. The i2c2 bus does not use the
trackpad pin. I would believe a better way is to have a node that holds both
trackpads and claims the pin for both at once. And that node not being the i2c bus
as there could be more devices on the bus and the pin would be taken regardless of
any trackpad probing , which is not right.
Another option is to disable parallel probing for the trackpads, such that when one
fails to probe, the pin is released and can be taken by the other one.
> + clock-frequency = <400000>;
> + i2c-scl-internal-delay-ns = <10000>;
> + status = "okay";
> +
> + trackpad@15 {
> + compatible = "elan,ekth3000";
> + reg = <0x15>;
> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> + vcc-supply = <&pp3300_s3>;
> + wakeup-source;
> + };
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> + clock-frequency = <100000>;
> + status = "okay";
> +
> + it6505dptx: dp-bridge@5c {
> + compatible = "ite,it6505";
> + reg = <0x5c>;
> + interrupts-extended = <&pio 8 IRQ_TYPE_LEVEL_LOW>;
> + ovdd-supply = <&mt6366_vsim2_reg>;
> + pwr18-supply = <&pp1800_dpbrdg_dx>;
> + reset-gpios = <&pio 177 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&it6505_pins>;
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #sound-dai-cells = <0>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + it6505_in: endpoint {
> + link-frequencies = /bits/ 64 <150000000>;
> + remote-endpoint = <&dpi_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> + };
> + };
> + };
> +};
> +
> +&i2c5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c5_pins>;
> + status = "okay";
> +
> + rt5682s: codec@1a {
> + compatible = "realtek,rt5682s";
> + reg = <0x1a>;
> + interrupts-extended = <&pio 17 IRQ_TYPE_EDGE_BOTH>;
> + AVDD-supply = <&mt6366_vio18_reg>;
> + DBVDD-supply = <&mt6366_vio18_reg>;
> + LDO1-IN-supply = <&mt6366_vio18_reg>;
> + MICVDD-supply = <&pp3300_z2>;
> + realtek,jd-src = <1>;
> + #sound-dai-cells = <1>;
> + };
> +};
> +
> +&mfg0 {
> + domain-supply = <&mt6366_vsram_gpu_reg>;
> +};
> +
> +&mfg1 {
> + domain-supply = <&mt6366_vgpu_reg>;
> +};
> +
> +&mipi_tx0 {
> + status = "okay";
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc0_pins_default>;
> + pinctrl-1 = <&mmc0_pins_uhs>;
> + bus-width = <8>;
> + max-frequency = <200000000>;
> + non-removable;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + supports-cqe;
> + no-sd;
> + no-sdio;
> + cap-mmc-hw-reset;
> + hs400-ds-delay = <0x11814>;
> + mediatek,hs400-ds-dly3 = <0x14>;
> + vmmc-supply = <&mt6366_vemc_reg>;
> + vqmmc-supply = <&mt6366_vio18_reg>;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default", "state_uhs", "state_eint";
> + pinctrl-0 = <&mmc1_pins_default>;
> + pinctrl-1 = <&mmc1_pins_uhs>;
> + pinctrl-2 = <&mmc1_pins_eint>;
> + /delete-property/ interrupts;
> + interrupt-names = "msdc", "sdio_wakeup";
> + interrupts-extended = <&gic GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH 0>,
> + <&pio 87 IRQ_TYPE_LEVEL_LOW>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + cap-sd-highspeed;
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + keep-power-in-suspend;
> + wakeup-source;
> + cap-sdio-irq;
> + no-mmc;
> + no-sd;
> + non-removable;
> + vmmc-supply = <&pp3300_s3>;
> + vqmmc-supply = <&mt6366_vio18_reg>;
> + mmc-pwrseq = <&wifi_pwrseq>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + bluetooth@2 {
> + compatible = "mediatek,mt7921s-bluetooth";
> + reg = <2>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&bt_pins_reset>;
> + reset-gpios = <&pio 155 GPIO_ACTIVE_LOW>;
> + };
> +};
> +
> +&nor_flash {
> + pinctrl-names = "default";
> + pinctrl-0 = <&nor_pins_default>;
> + assigned-clock-parents = <&topckgen CLK_TOP_MAINPLL_D7_D4>;
> + status = "okay";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <39000000>;
> + };
> +};
> +
> +&pio {
> + /* 185 lines */
> + gpio-line-names = "TP",
> + "TP",
> + "TP",
> + "I2S0_HP_DI",
> + "I2S3_DP_SPKR_DO",
> + "SAR_INT_ODL",
> + "BT_WAKE_AP_ODL",
> + "WIFI_INT_ODL",
> + "DPBRDG_INT_ODL",
> + "EDPBRDG_INT_ODL",
> + "EC_AP_HPD_OD",
> + "TCHPAD_INT_ODL",
> + "TCHSCR_INT_1V8_ODL",
> + "EC_AP_INT_ODL",
> + "EC_IN_RW_ODL",
> + "GSC_AP_INT_ODL",
> + /* AP_FLASH_WP_L is crossystem ABI. Rev1 schematics call it AP_WP_ODL. */
> + "AP_FLASH_WP_L",
> + "HP_INT_ODL",
> + "PEN_EJECT_OD",
> + "WCAM_PWDN_L",
> + "WCAM_RST_L",
> + "UCAM_SEN_EN",
> + "UCAM_RST_L",
> + "LTE_RESET_L",
> + "LTE_SAR_DETECT_L",
> + "I2S2_DP_SPK_MCK",
> + "I2S2_DP_SPKR_BCK",
> + "I2S2_DP_SPKR_LRCK",
> + "I2S2_DP_SPKR_DI (TP)",
> + "EN_PP1000_EDPBRDG",
> + "EN_PP1800_EDPBRDG",
> + "EN_PP3300_EDPBRDG",
> + "UART_GSC_TX_AP_RX",
> + "UART_AP_TX_GSC_RX",
> + "UART_DBGCON_TX_ADSP_RX",
> + "UART_ADSP_TX_DBGCON_RX",
> + "EN_PP1000_DPBRDG",
> + "TCHSCR_REPORT_DISABLE",
> + "EN_PP3300_DPBRDG",
> + "EN_PP1800_DPBRDG",
> + "SPI_AP_CLK_EC",
> + "SPI_AP_CS_EC_L",
> + "SPI_AP_DO_EC_DI",
> + "SPI_AP_DI_EC_DO",
> + "SPI_AP_CLK_GSC",
> + "SPI_AP_CS_GSC_L",
> + "SPI_AP_DO_GSC_DI",
> + "SPI_AP_DI_GSC_DO",
> + "UART_DBGCON_TX_SCP_RX",
> + "UART_SCP_TX_DBGCON_RX",
> + "EN_PP1200_CAM_X",
> + "EN_PP2800A_VCM_X",
> + "EN_PP2800A_UCAM_X",
> + "EN_PP2800A_WCAM_X",
> + "WLAN_MODULE_RST_L",
> + "EN_PP1200_UCAM_X",
> + "I2S1_HP_DO",
> + "I2S1_HP_BCK",
> + "I2S1_HP_LRCK",
> + "I2S1_HP_MCK",
> + "TCHSCR_RST_1V8_L",
> + "SPI_AP_CLK_ROM",
> + "SPI_AP_CS_ROM_L",
> + "SPI_AP_DO_ROM_DI",
> + "SPI_AP_DI_ROM_DO",
> + "NC",
> + "NC",
> + "EMMC_STRB",
> + "EMMC_CLK",
> + "EMMC_CMD",
> + "EMMC_RST_L",
> + "EMMC_DATA0",
> + "EMMC_DATA1",
> + "EMMC_DATA2",
> + "EMMC_DATA3",
> + "EMMC_DATA4",
> + "EMMC_DATA5",
> + "EMMC_DATA6",
> + "EMMC_DATA7",
> + "AP_KPCOL0",
> + "NC",
> + "NC",
> + "NC",
> + "TP",
> + "SDIO_CLK",
> + "SDIO_CMD",
> + "SDIO_DATA0",
> + "SDIO_DATA1",
> + "SDIO_DATA2",
> + "SDIO_DATA3",
> + "NC",
> + "NC",
> + "NC",
> + "NC",
> + "NC",
> + "NC",
> + "EDPBRDG_PWREN",
> + "BL_PWM_1V8",
> + "EDPBRDG_RST_L",
> + "MIPI_DPI_CLK",
> + "MIPI_DPI_VSYNC",
> + "MIPI_DPI_HSYNC",
> + "MIPI_DPI_DE",
> + "MIPI_DPI_D0",
> + "MIPI_DPI_D1",
> + "MIPI_DPI_D2",
> + "MIPI_DPI_D3",
> + "MIPI_DPI_D4",
> + "MIPI_DPI_D5",
> + "MIPI_DPI_D6",
> + "MIPI_DPI_DA7",
> + "MIPI_DPI_D8",
> + "MIPI_DPI_D9",
> + "MIPI_DPI_D10",
> + "MIPI_DPI_D11",
> + "PCM_BT_CLK",
> + "PCM_BT_SYNC",
> + "PCM_BT_DI",
> + "PCM_BT_DO",
> + "JTAG_TMS_TP",
> + "JTAG_TCK_TP",
> + "JTAG_TDI_TP",
> + "JTAG_TDO_TP",
> + "JTAG_TRSTN_TP",
> + "CLK_24M_WCAM",
> + "CLK_24M_UCAM",
> + "UCAM_DET_ODL",
> + "AP_I2C_EDPBRDG_SCL_1V8",
> + "AP_I2C_EDPBRDG_SDA_1V8",
> + "AP_I2C_TCHSCR_SCL_1V8",
> + "AP_I2C_TCHSCR_SDA_1V8",
> + "AP_I2C_TCHPAD_SCL_1V8",
> + "AP_I2C_TCHPAD_SDA_1V8",
> + "AP_I2C_DPBRDG_SCL_1V8",
> + "AP_I2C_DPBRDG_SDA_1V8",
> + "AP_I2C_WLAN_SCL_1V8",
> + "AP_I2C_WLAN_SDA_1V8",
> + "AP_I2C_AUD_SCL_1V8",
> + "AP_I2C_AUD_SDA_1V8",
> + "AP_I2C_TPM_SCL_1V8",
> + "AP_I2C_UCAM_SDA_1V8",
> + "AP_I2C_UCAM_SCL_1V8",
> + "AP_I2C_UCAM_SDA_1V8",
> + "AP_I2C_WCAM_SCL_1V8",
> + "AP_I2C_WCAM_SDA_1V8",
> + "SCP_I2C_SENSOR_SCL_1V8",
> + "SCP_I2C_SENSOR_SDA_1V8",
> + "AP_EC_WARM_RST_REQ",
> + "AP_XHCI_INIT_DONE",
> + "USB3_HUB_RST_L",
> + "EN_SPKR",
> + "BEEP_ON",
> + "AP_EDP_BKLTEN",
> + "EN_PP3300_DISP_X",
> + "EN_PP3300_SDBRDG_X",
> + "BT_KILL_1V8_L",
> + "WIFI_KILL_1V8_L",
> + "PWRAP_SPI0_CSN",
> + "PWRAP_SPI0_CK",
> + "PWRAP_SPI0_MO",
> + "PWRAP_SPI0_MI",
> + "SRCLKENA0",
> + "SRCLKENA1",
> + "SCP_VREQ_VAO",
> + "AP_RTC_CLK32K",
> + "AP_PMIC_WDTRST_L",
> + "AUD_CLK_MOSI",
> + "AUD_SYNC_MOSI",
> + "AUD_DAT_MOSI0",
> + "AUD_DAT_MOSI1",
> + "AUD_CLK_MISO",
> + "AUD_SYNC_MISO",
> + "AUD_DAT_MISO0",
> + "AUD_DAT_MISO1",
> + "NC",
> + "NC",
> + "DPBRDG_PWREN",
> + "DPBRDG_RST_L",
> + "LTE_W_DISABLE_L",
> + "LTE_SAR_DETECT_L",
> + "EN_PP3300_LTE_X",
> + "LTE_PWR_OFF_L",
> + "LTE_RESET_L",
> + "TP",
> + "TP";
> +
> + aud_clk_mosi_off: aud-clk-mosi-off-pins {
> + pins-clk-sync {
> + pinmux = <PINMUX_GPIO166__FUNC_GPIO166>,
> + <PINMUX_GPIO167__FUNC_GPIO167>;
> + input-enable;
> + bias-pull-down;
> + };
> + };
> +
> + aud_clk_mosi_on: aud-clk-mosi-on-pins {
> + pins-clk-sync {
> + pinmux = <PINMUX_GPIO166__FUNC_AUD_CLK_MOSI>,
> + <PINMUX_GPIO167__FUNC_AUD_SYNC_MOSI>;
> + };
> + };
> +
> + aud_clk_miso_off: aud-clk-miso-off-pins {
> + pins-clk-sync {
> + pinmux = <PINMUX_GPIO170__FUNC_GPIO170>,
> + <PINMUX_GPIO171__FUNC_GPIO171>;
> + input-enable;
> + bias-pull-down;
> + };
> + };
> +
> + aud_clk_miso_on: aud-clk-miso-on-pins {
> + pins-clk-sync {
> + pinmux = <PINMUX_GPIO170__FUNC_AUD_CLK_MISO>,
> + <PINMUX_GPIO171__FUNC_AUD_SYNC_MISO>;
> + };
> + };
> +
> + aud_dat_mosi_off: aud-dat-mosi-off-pins {
> + pins-dat {
> + pinmux = <PINMUX_GPIO168__FUNC_GPIO168>,
> + <PINMUX_GPIO169__FUNC_GPIO169>;
> + input-enable;
> + bias-pull-down;
> + };
> + };
> +
> + aud_dat_mosi_on: aud-dat-mosi-on-pins {
> + pins-dat {
> + pinmux = <PINMUX_GPIO168__FUNC_AUD_DAT_MOSI0>,
> + <PINMUX_GPIO169__FUNC_AUD_DAT_MOSI1>;
> + };
> + };
> +
> + aud_dat_miso_off: aud-dat-miso-off-pins {
> + pins-dat {
> + pinmux = <PINMUX_GPIO172__FUNC_GPIO172>,
> + <PINMUX_GPIO173__FUNC_GPIO173>;
> + input-enable;
> + bias-pull-down;
> + };
> + };
> +
> + aud_dat_miso_on: aud-dat-miso-on-pins {
> + pins-dat {
> + pinmux = <PINMUX_GPIO172__FUNC_AUD_DAT_MISO0>,
> + <PINMUX_GPIO173__FUNC_AUD_DAT_MISO1>;
> + input-schmitt-enable;
> + bias-disable;
> + };
> + };
> +
> + aud_gpio_i2s0_off: aud-gpio-i2s0-off-pins {
> + pins-sdata {
> + pinmux = <PINMUX_GPIO3__FUNC_GPIO3>;
> + };
> + };
> +
> + aud_gpio_i2s0_on: aud-gpio-i2s0-on-pins {
> + pins-sdata {
> + pinmux = <PINMUX_GPIO3__FUNC_I2S0_DI>;
> + };
> + };
> +
> + aud_gpio_i2s1_off: aud-gpio-i2s-off-pins {
> + pins-clk-sdata {
> + pinmux = <PINMUX_GPIO56__FUNC_GPIO56>,
> + <PINMUX_GPIO57__FUNC_GPIO57>,
> + <PINMUX_GPIO58__FUNC_GPIO58>,
> + <PINMUX_GPIO59__FUNC_GPIO59>;
> + output-low;
> + };
> + };
> +
> + aud_gpio_i2s1_on: aud-gpio-i2s1-on-pins {
> + pins-clk-sdata {
> + pinmux = <PINMUX_GPIO56__FUNC_I2S1_DO>,
> + <PINMUX_GPIO57__FUNC_I2S1_BCK>,
> + <PINMUX_GPIO58__FUNC_I2S1_LRCK>,
> + <PINMUX_GPIO59__FUNC_I2S1_MCK>;
> + };
> + };
> +
> + aud_gpio_i2s2_off: aud-gpio-i2s2-off-pins {
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO26__FUNC_GPIO26>,
> + <PINMUX_GPIO27__FUNC_GPIO27>;
> + output-low;
> + };
> + };
> +
> + aud_gpio_i2s2_on: aud-gpio-i2s2-on-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO26__FUNC_I2S2_BCK>,
> + <PINMUX_GPIO27__FUNC_I2S2_LRCK>;
> + drive-strength = <4>;
> + };
> + };
> +
> + aud_gpio_i2s3_off: aud-gpio-i2s3-off-pins {
> + pins-sdata {
> + pinmux = <PINMUX_GPIO4__FUNC_GPIO4>;
> + output-low;
> + };
> + };
> +
> + aud_gpio_i2s3_on: aud-gpio-i2s3-on-pins {
> + pins-sdata {
> + pinmux = <PINMUX_GPIO4__FUNC_I2S3_DO>;
> + drive-strength = <4>;
> + };
> + };
> +
> + aud_gpio_tdm_off: aud-gpio-tdm-off-pins { };
> +
> + aud_gpio_tdm_on: aud-gpio-tdm-on-pins { };
Guess have to remove these two empty pinctrls.
> +
> + aud_gpio_pcm_off: aud-gpio-pcm-off-pins {
> + pins-clk-sdata {
> + pinmux = <PINMUX_GPIO115__FUNC_GPIO115>,
> + <PINMUX_GPIO116__FUNC_GPIO116>,
> + <PINMUX_GPIO117__FUNC_GPIO117>,
> + <PINMUX_GPIO118__FUNC_GPIO118>;
> + output-low;
> + };
> + };
> +
> + aud_gpio_pcm_on: aud-gpio-pcm-on-pins {
> + pins-clk-sdata {
> + pinmux = <PINMUX_GPIO115__FUNC_PCM_CLK>,
> + <PINMUX_GPIO116__FUNC_PCM_SYNC>,
> + <PINMUX_GPIO117__FUNC_PCM_DI>,
> + <PINMUX_GPIO118__FUNC_PCM_DO>;
> + };
> + };
> +
> + aud_gpio_dmic_sec: aud-gpio-dmic-sec-pins {
> + pins {
> + pinmux = <PINMUX_GPIO23__FUNC_GPIO23>;
> + output-low;
> + };
> + };
> +
> + bt_pins_reset: bt-reset-pins {
> + pins-bt-reset {
> + pinmux = <PINMUX_GPIO155__FUNC_GPIO155>;
> + output-high;
> + };
> + };
> +
> + dpi_pins_sleep: dpi-sleep-pins {
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO103__FUNC_GPIO103>,
> + <PINMUX_GPIO104__FUNC_GPIO104>,
> + <PINMUX_GPIO105__FUNC_GPIO105>,
> + <PINMUX_GPIO106__FUNC_GPIO106>,
> + <PINMUX_GPIO107__FUNC_GPIO107>,
> + <PINMUX_GPIO108__FUNC_GPIO108>,
> + <PINMUX_GPIO109__FUNC_GPIO109>,
> + <PINMUX_GPIO110__FUNC_GPIO110>,
> + <PINMUX_GPIO111__FUNC_GPIO111>,
> + <PINMUX_GPIO112__FUNC_GPIO112>,
> + <PINMUX_GPIO113__FUNC_GPIO113>,
> + <PINMUX_GPIO114__FUNC_GPIO114>,
> + <PINMUX_GPIO101__FUNC_GPIO101>,
> + <PINMUX_GPIO100__FUNC_GPIO100>,
> + <PINMUX_GPIO102__FUNC_GPIO102>,
> + <PINMUX_GPIO99__FUNC_GPIO99>;
> + drive-strength = <10>;
> + output-low;
> + };
> + };
> +
> + dpi_pins_default: dpi-default-pins {
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO103__FUNC_DPI_DATA0>,
> + <PINMUX_GPIO104__FUNC_DPI_DATA1>,
> + <PINMUX_GPIO105__FUNC_DPI_DATA2>,
> + <PINMUX_GPIO106__FUNC_DPI_DATA3>,
> + <PINMUX_GPIO107__FUNC_DPI_DATA4>,
> + <PINMUX_GPIO108__FUNC_DPI_DATA5>,
> + <PINMUX_GPIO109__FUNC_DPI_DATA6>,
> + <PINMUX_GPIO110__FUNC_DPI_DATA7>,
> + <PINMUX_GPIO111__FUNC_DPI_DATA8>,
> + <PINMUX_GPIO112__FUNC_DPI_DATA9>,
> + <PINMUX_GPIO113__FUNC_DPI_DATA10>,
> + <PINMUX_GPIO114__FUNC_DPI_DATA11>,
> + <PINMUX_GPIO101__FUNC_DPI_HSYNC>,
> + <PINMUX_GPIO100__FUNC_DPI_VSYNC>,
> + <PINMUX_GPIO102__FUNC_DPI_DE>,
> + <PINMUX_GPIO99__FUNC_DPI_PCLK>;
> + drive-strength = <10>;
> + };
> + };
> +
> + ec_ap_int: cros-ec-int-pins {
> + pins-ec-ap-int-odl {
> + pinmux = <PINMUX_GPIO13__FUNC_GPIO13>;
> + input-enable;
> + };
> + };
> +
> + edp_panel_fixed_pins: edp-panel-fixed-pins {
> + pins-vreg-en {
> + pinmux = <PINMUX_GPIO153__FUNC_GPIO153>;
> + output-high;
> + };
> + };
> +
> + en_pp1800_dpbrdg: en-pp1800-dpbrdg-pins {
> + pins-vreg-en {
> + pinmux = <PINMUX_GPIO39__FUNC_GPIO39>;
> + output-low;
> + };
> + };
> +
> + gsc_int: gsc-int-pins {
> + pins-gsc-ap-int-odl {
> + pinmux = <PINMUX_GPIO15__FUNC_GPIO15>;
> + input-enable;
> + };
> + };
> +
> + i2c0_pins: i2c0-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO128__FUNC_SDA0>,
> + <PINMUX_GPIO127__FUNC_SCL0>;
> + bias-disable;
> + drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
> + i2c1_pins: i2c1-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO130__FUNC_SDA1>,
> + <PINMUX_GPIO129__FUNC_SCL1>;
> + bias-disable;
> + drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
> + i2c2_pins: i2c2-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO132__FUNC_SDA2>,
> + <PINMUX_GPIO131__FUNC_SCL2>;
> + bias-disable;
> + drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
> + i2c3_pins: i2c3-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO134__FUNC_SDA3>,
> + <PINMUX_GPIO133__FUNC_SCL3>;
> + bias-disable;
> + drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
> + i2c5_pins: i2c5-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO138__FUNC_SDA5>,
> + <PINMUX_GPIO137__FUNC_SCL5>;
> + bias-disable;
> + drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
> + it6505_pins: it6505-pins {
> + pins-hpd {
> + pinmux = <PINMUX_GPIO10__FUNC_GPIO10>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + pins-int {
> + pinmux = <PINMUX_GPIO8__FUNC_GPIO8>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + pins-reset {
> + pinmux = <PINMUX_GPIO177__FUNC_GPIO177>;
> + output-low;
> + bias-pull-up;
> + };
> + };
> +
> + mmc0_pins_default: mmc0-default-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO68__FUNC_MSDC0_CLK>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO71__FUNC_MSDC0_DAT0>,
> + <PINMUX_GPIO72__FUNC_MSDC0_DAT1>,
> + <PINMUX_GPIO73__FUNC_MSDC0_DAT2>,
> + <PINMUX_GPIO74__FUNC_MSDC0_DAT3>,
> + <PINMUX_GPIO75__FUNC_MSDC0_DAT4>,
> + <PINMUX_GPIO76__FUNC_MSDC0_DAT5>,
> + <PINMUX_GPIO77__FUNC_MSDC0_DAT6>,
> + <PINMUX_GPIO78__FUNC_MSDC0_DAT7>,
> + <PINMUX_GPIO69__FUNC_MSDC0_CMD>;
> + input-enable;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins-rst {
> + pinmux = <PINMUX_GPIO70__FUNC_MSDC0_RSTB>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + mmc0_pins_uhs: mmc0-uhs-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO68__FUNC_MSDC0_CLK>;
> + drive-strength = <6>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO71__FUNC_MSDC0_DAT0>,
> + <PINMUX_GPIO72__FUNC_MSDC0_DAT1>,
> + <PINMUX_GPIO73__FUNC_MSDC0_DAT2>,
> + <PINMUX_GPIO74__FUNC_MSDC0_DAT3>,
> + <PINMUX_GPIO75__FUNC_MSDC0_DAT4>,
> + <PINMUX_GPIO76__FUNC_MSDC0_DAT5>,
> + <PINMUX_GPIO77__FUNC_MSDC0_DAT6>,
> + <PINMUX_GPIO78__FUNC_MSDC0_DAT7>,
> + <PINMUX_GPIO69__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <6>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins-ds {
> + pinmux = <PINMUX_GPIO67__FUNC_MSDC0_DSL>;
> + drive-strength = <6>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-rst {
> + pinmux = <PINMUX_GPIO70__FUNC_MSDC0_RSTB>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + mmc1_pins_default: mmc1-default-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO84__FUNC_MSDC1_CLK>;
> + drive-strength = <6>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO86__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO87__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO88__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO89__FUNC_MSDC1_DAT3>,
> + <PINMUX_GPIO85__FUNC_MSDC1_CMD>;
> + input-enable;
> + drive-strength = <6>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + mmc1_pins_uhs: mmc1-uhs-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO84__FUNC_MSDC1_CLK>;
> + drive-strength = <6>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO86__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO87__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO88__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO89__FUNC_MSDC1_DAT3>,
> + <PINMUX_GPIO85__FUNC_MSDC1_CMD>;
> + input-enable;
> + drive-strength = <8>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + mmc1_pins_eint: mmc1-eint-pins {
> + pins-dat1 {
> + pinmux = <PINMUX_GPIO87__FUNC_GPIO87>;
> + input-enable;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + nor_pins_default: nor-default-pins {
> + pins-clk-dat {
> + pinmux = <PINMUX_GPIO63__FUNC_SPINOR_IO0>,
> + <PINMUX_GPIO61__FUNC_SPINOR_CK>,
> + <PINMUX_GPIO64__FUNC_SPINOR_IO1>;
> + drive-strength = <6>;
> + bias-pull-down;
> + };
> +
> + pins-cs-dat {
> + pinmux = <PINMUX_GPIO62__FUNC_SPINOR_CS>,
> + <PINMUX_GPIO65__FUNC_SPINOR_IO2>,
> + <PINMUX_GPIO66__FUNC_SPINOR_IO3>;
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> + };
> +
> + pen_eject: pen-eject-pins {
> + pins {
> + pinmux = <PINMUX_GPIO18__FUNC_GPIO18>;
> + input-enable;
> + /* External pull-up. */
> + bias-disable;
> + };
> + };
> +
> + pwm0_pin: disp-pwm-pins {
> + pins {
> + pinmux = <PINMUX_GPIO97__FUNC_DISP_PWM>;
> + output-high;
> + };
> + };
> +
> + rt1019p_pins_default: rt1019p-default-pins {
> + pins-sdb {
> + pinmux = <PINMUX_GPIO150__FUNC_GPIO150>;
> + output-low;
> + };
> + };
> +
> + scp_pins: scp-default-pins {
> + pins-scp-uart {
> + pinmux = <PINMUX_GPIO48__FUNC_TP_URXD2_AO>,
> + <PINMUX_GPIO49__FUNC_TP_UTXD2_AO>;
> + };
> + };
> +
> + spi1_pins: spi1-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO40__FUNC_SPI1_CLK_A>,
> + <PINMUX_GPIO41__FUNC_SPI1_CSB_A>,
> + <PINMUX_GPIO42__FUNC_SPI1_MO_A>,
> + <PINMUX_GPIO43__FUNC_SPI1_MI_A>;
> + bias-disable;
> + input-enable;
> + };
> + };
> +
> + spi2_pins: spi2-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO44__FUNC_SPI2_CLK_A>,
> + <PINMUX_GPIO45__FUNC_GPIO45>,
> + <PINMUX_GPIO46__FUNC_SPI2_MO_A>,
> + <PINMUX_GPIO47__FUNC_SPI2_MI_A>;
> + bias-disable;
> + input-enable;
> + };
> + };
> +
> + spmi_pins: spmi-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO183__FUNC_SPMI_SCL>,
> + <PINMUX_GPIO184__FUNC_SPMI_SDA>;
> + };
> + };
> +
> + touchscreen_pins: touchscreen-pins {
> + pins-irq {
> + pinmux = <PINMUX_GPIO12__FUNC_GPIO12>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + pins-reset {
> + pinmux = <PINMUX_GPIO60__FUNC_GPIO60>;
> + output-high;
> + };
> +
> + pins-report-sw {
> + pinmux = <PINMUX_GPIO37__FUNC_GPIO37>;
> + output-low;
> + };
> + };
> +
> + trackpad_pin: trackpad-default-pins {
> + pins-int-n {
> + pinmux = <PINMUX_GPIO11__FUNC_GPIO11>;
> + input-enable;
> + bias-disable; /* pulled externally */
> + };
> + };
> +
> + wifi_enable_pin: wifi-enable-pins {
> + pins-wifi-enable {
> + pinmux = <PINMUX_GPIO54__FUNC_GPIO54>;
> + };
> + };
> +
> + wifi_wakeup_pin: wifi-wakeup-pins {
> + pins-wifi-wakeup {
> + pinmux = <PINMUX_GPIO7__FUNC_GPIO7>;
> + input-enable;
> + };
> + };
> +};
> +
> +&pwm0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwm0_pin>;
> + status = "okay";
> +};
> +
> +&pwrap {
> + pmic {
> + compatible = "mediatek,mt6366", "mediatek,mt6358";
> + interrupt-controller;
> + interrupts-extended = <&pio 201 IRQ_TYPE_LEVEL_HIGH>;
> + #interrupt-cells = <2>;
> +
> + mt6366codec: codec {
> + compatible = "mediatek,mt6366-sound", "mediatek,mt6358-sound";
> + Avdd-supply = <&mt6366_vaud28_reg>;
> + mediatek,dmic-mode = <1>; /* one-wire */
> + };
> +
> + mt6366_regulators: regulators {
> + compatible = "mediatek,mt6366-regulator", "mediatek,mt6358-regulator";
> + vsys-ldo1-supply = <&pp4200_z2>;
> + vsys-ldo2-supply = <&pp4200_z2>;
> + vsys-ldo3-supply = <&pp4200_z2>;
> + vsys-vcore-supply = <&pp4200_z2>;
> + vsys-vdram1-supply = <&pp4200_z2>;
> + vsys-vgpu-supply = <&pp4200_z2>;
> + vsys-vmodem-supply = <&pp4200_z2>;
> + vsys-vpa-supply = <&pp4200_z2>;
> + vsys-vproc11-supply = <&pp4200_z2>;
> + vsys-vproc12-supply = <&pp4200_z2>;
> + vsys-vs1-supply = <&pp4200_z2>;
> + vsys-vs2-supply = <&pp4200_z2>;
> + vs1-ldo1-supply = <&mt6366_vs1_reg>;
> + vs2-ldo1-supply = <&mt6366_vdram1_reg>;
> + vs2-ldo2-supply = <&mt6366_vs2_reg>;
> + vs2-ldo3-supply = <&mt6366_vs2_reg>;
> +
> + vcore {
> + regulator-name = "pp0750_dvdd_core";
> + regulator-min-microvolt = <550000>;
> + regulator-max-microvolt = <800000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <200>;
> + regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
> + MT6397_BUCK_MODE_FORCE_PWM>;
> + regulator-always-on;
> + };
> +
> + mt6366_vdram1_reg: vdram1 {
> + regulator-name = "pp1125_emi_vdd2";
> + regulator-min-microvolt = <1125000>;
> + regulator-max-microvolt = <1125000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <0>;
> + regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
> + MT6397_BUCK_MODE_FORCE_PWM>;
> + regulator-always-on;
> + };
> +
> + mt6366_vgpu_reg: vgpu {
> + /*
> + * Called "ppvar_dvdd_gpu" in the schematic.
> + * Called "ppvar_dvdd_vgpu" here to match
> + * regulator coupling requirements.
> + */
> + regulator-name = "ppvar_dvdd_vgpu";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <950000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <200>;
> + regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
> + MT6397_BUCK_MODE_FORCE_PWM>;
> + regulator-coupled-with = <&mt6366_vsram_gpu_reg>;
> + regulator-coupled-max-spread = <10000>;
> + };
> +
> + mt6366_vproc11_reg: vproc11 {
> + regulator-name = "ppvar_dvdd_proc_bc_mt6366";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <200>;
> + regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
> + MT6397_BUCK_MODE_FORCE_PWM>;
> + regulator-always-on;
> + };
> +
> + mt6366_vproc12_reg: vproc12 {
> + regulator-name = "ppvar_dvdd_proc_lc";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <200>;
> + regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
> + MT6397_BUCK_MODE_FORCE_PWM>;
> + regulator-always-on;
> + };
> +
> + mt6366_vs1_reg: vs1 {
> + regulator-name = "pp2000_vs1";
> + regulator-min-microvolt = <2000000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <0>;
> + regulator-always-on;
> + };
> +
> + mt6366_vs2_reg: vs2 {
> + regulator-name = "pp1350_vs2";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-ramp-delay = <12500>;
> + regulator-enable-ramp-delay = <0>;
> + regulator-always-on;
> + };
> +
> + va12 {
> + regulator-name = "pp1200_va12";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-enable-ramp-delay = <270>;
> + regulator-always-on;
> + };
> +
> + mt6366_vaud28_reg: vaud28 {
> + regulator-name = "pp2800_vaud28";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vaux18_reg: vaux18 {
> + regulator-name = "pp1840_vaux18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1840000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vbif28_reg: vbif28 {
> + regulator-name = "pp2800_vbif28";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vcn18_reg: vcn18 {
> + regulator-name = "pp1800_vcn18_x";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vcn28_reg: vcn28 {
> + regulator-name = "pp2800_vcn28_x";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vefuse_reg: vefuse {
> + regulator-name = "pp1800_vefuse";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vfe28_reg: vfe28 {
> + regulator-name = "pp2800_vfe28_x";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vemc_reg: vemc {
> + regulator-name = "pp3000_vemc";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-enable-ramp-delay = <60>;
> + };
> +
> + mt6366_vibr_reg: vibr {
> + regulator-name = "pp2800_vibr_x";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-enable-ramp-delay = <60>;
> + };
> +
> + mt6366_vio18_reg: vio18 {
> + regulator-name = "pp1800_vio18_s3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <2700>;
> + regulator-always-on;
> + };
> +
> + mt6366_vio28_reg: vio28 {
> + regulator-name = "pp2800_vio28_x";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + mt6366_vm18_reg: vm18 {
> + regulator-name = "pp1800_emi_vdd1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1840000>;
> + regulator-enable-ramp-delay = <325>;
> + regulator-always-on;
> + };
> +
> + mt6366_vmc_reg: vmc {
> + regulator-name = "pp3000_vmc";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-enable-ramp-delay = <60>;
> + };
> +
> + mt6366_vmddr_reg: vmddr {
> + regulator-name = "pm0750_emi_vmddr";
> + regulator-min-microvolt = <700000>;
> + regulator-max-microvolt = <750000>;
> + regulator-enable-ramp-delay = <325>;
> + regulator-always-on;
> + };
> +
> + mt6366_vmch_reg: vmch {
> + regulator-name = "pp3000_vmch";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-enable-ramp-delay = <60>;
> + };
> +
> + mt6366_vcn33_reg: vcn33 {
> + regulator-name = "pp3300_vcn33_x";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-enable-ramp-delay = <270>;
> + };
> +
> + vdram2 {
> + regulator-name = "pp0600_emi_vddq";
> + regulator-min-microvolt = <600000>;
> + regulator-max-microvolt = <600000>;
> + regulator-enable-ramp-delay = <3300>;
> + regulator-always-on;
> + };
> +
> + mt6366_vrf12_reg: vrf12 {
> + regulator-name = "pp1200_vrf12_x";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-enable-ramp-delay = <120>;
> + };
> +
> + mt6366_vrf18_reg: vrf18 {
> + regulator-name = "pp1800_vrf18_x";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-enable-ramp-delay = <120>;
> + };
> +
> + vsim1 {
> + regulator-name = "pp1860_vsim1_x";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1860000>;
> + regulator-enable-ramp-delay = <540>;
> + };
> +
> + mt6366_vsim2_reg: vsim2 {
> + regulator-name = "pp2760_vsim2_x";
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <2760000>;
> + regulator-enable-ramp-delay = <540>;
> + };
> +
> + mt6366_vsram_gpu_reg: vsram-gpu {
> + regulator-name = "pp0900_dvdd_sram_gpu";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1050000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <240>;
> + regulator-coupled-with = <&mt6366_vgpu_reg>;
> + regulator-coupled-max-spread = <10000>;
> + };
> +
> + mt6366_vsram_others_reg: vsram-others {
> + regulator-name = "pp0900_dvdd_sram_core";
> + regulator-min-microvolt = <900000>;
> + regulator-max-microvolt = <900000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <240>;
> + regulator-always-on;
> + };
> +
> + mt6366_vsram_proc11_reg: vsram-proc11 {
> + regulator-name = "pp0900_dvdd_sram_bc";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1120000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <240>;
> + regulator-always-on;
> + };
> +
> + mt6366_vsram_proc12_reg: vsram-proc12 {
> + regulator-name = "pp0900_dvdd_sram_lc";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1120000>;
> + regulator-ramp-delay = <6250>;
> + regulator-enable-ramp-delay = <240>;
> + regulator-always-on;
> + };
> +
> + vusb {
> + regulator-name = "pp3070_vusb";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3070000>;
> + regulator-enable-ramp-delay = <270>;
> + regulator-always-on;
> + };
> +
> + vxo22 {
> + regulator-name = "pp2240_vxo22";
> + regulator-min-microvolt = <2200000>;
> + regulator-max-microvolt = <2240000>;
> + regulator-enable-ramp-delay = <120>;
> + /* Feeds DCXO internally */
> + regulator-always-on;
> + };
> + };
> +
> + rtc {
> + compatible = "mediatek,mt6366-rtc", "mediatek,mt6358-rtc";
> + };
> + };
> +};
> +
> +&scp {
> + pinctrl-names = "default";
> + pinctrl-0 = <&scp_pins>;
> + firmware-name = "mediatek/mt8186/scp.img";
> + memory-region = <&scp_mem>;
> + status = "okay";
> +
> + cros-ec-rpmsg {
> + compatible = "google,cros-ec-rpmsg";
> + mediatek,rpmsg-name = "cros-ec-rpmsg";
> + };
> +};
> +
> +&spi1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_pins>;
> + mediatek,pad-select = <0>;
> + status = "okay";
> +
> + cros_ec: ec@0 {
> + compatible = "google,cros-ec-spi";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + interrupts-extended = <&pio 13 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ec_ap_int>;
> +
> + i2c_tunnel: i2c-tunnel {
> + compatible = "google,cros-ec-i2c-tunnel";
> + google,remote-bus = <1>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + typec {
> + compatible = "google,cros-ec-typec";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + usb_c0: connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + label = "left";
> + power-role = "dual";
> + data-role = "host";
> + try-power-role = "source";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <1>;
> +
> + typec_port0: endpoint { };
> + };
> + };
> + };
> +
> + usb_c1: connector@1 {
> + compatible = "usb-c-connector";
> + reg = <1>;
> + label = "right";
> + power-role = "dual";
> + data-role = "host";
> + try-power-role = "source";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <1>;
> +
> + typec_port1: endpoint { };
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&spi2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi2_pins>;
> + cs-gpios = <&pio 45 GPIO_ACTIVE_LOW>;
> + mediatek,pad-select = <0>;
> + status = "okay";
> +
> + tpm@0 {
> + compatible = "google,cr50";
> + reg = <0>;
> + spi-max-frequency = <1000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&gsc_int>;
> + interrupt-parent = <&pio>;
> + interrupts = <15 IRQ_TYPE_EDGE_RISING>;
> + };
> +};
> +
> +&ssusb0 {
> + status = "okay";
> +};
> +
> +&ssusb1 {
> + status = "okay";
> +};
> +
> +&u3phy0 {
> + status = "okay";
> +};
> +
> +&u3phy1 {
> + status = "okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&usb_host0 {
> + vbus-supply = <&pp3300_s3>;
> + status = "okay";
> +};
> +
> +&usb_host1 {
> + vbus-supply = <&usb_p1_vbus>;
> + status = "okay";
> + #address-cells = <2>;
> + #size-cells = <2>;
> +};
> +
> +&watchdog {
> + mediatek,reset-by-toprgu;
> +};
> +
> +#include <arm/cros-ec-keyboard.dtsi>
> +#include <arm/cros-ec-sbs.dtsi>
Il 04/12/23 09:40, Chen-Yu Tsai ha scritto:
> Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> Krabby design.
>
> Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> convertible device with touchscreen and stylus.
>
> Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> device. It does not have a touchscreen or stylus.
>
> The two devices both have two variants. The difference is a second
> source touchpad controller that shares the same address as the original,
> but is incompatible.
>
> The extra SKU IDs for the Tentacruel devices map to different sensor
> components attached to the Embedded Controller. These are not visible
> to the main processor.
>
> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> ---
> Changes since v2:
> - Picked up Conor's ack
> - Rename touchpad to trackpad
> - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> source trackpad
>
> Changes since v1:
> - Reorder SKU numbers in descending order.
> - Fixed pinconfig node names
> - Moved pinctrl-* properties after interrupts-*
> - Switched to interrupts-extended for external components
> - Marked ADSP as explicitly disabled, with a comment explaining that it
> stalls the system
> - Renamed "touchpad" to "trackpad"
> - Dropped bogus "no-laneswap" property from it6505 node
> - Moved "realtek,jd-src" property to after all the regulator supplies
> - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> - Renamed "vgpu" regulator name to allow coupling, with a comment
> containing the name used in the design
> - Renamed "cr50" node name to "tpm"
> - Moved trackpad_pins reference up to i2c2; workaround for second source
> component resource sharing.
> - Fix copyright year
> - Fixed touchscreen supply name
>
> arch/arm64/boot/dts/mediatek/Makefile | 4 +
> .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
> 7 files changed, 2003 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index e6e7592a3645..442af61b1305 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> new file mode 100644
> index 000000000000..9b2b64525961
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> @@ -0,0 +1,129 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2022 Google LLC
> + */
> +
> +/dts-v1/;
> +#include "mt8186-corsola.dtsi"
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + aliases {
> + i2c4 = &i2c4;
> + };
> +};
> +
> +&dsi_out {
> + remote-endpoint = <&ps8640_in>;
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> +
> + ps8640: edp-bridge@8 {
> + compatible = "parade,ps8640";
> + reg = <0x8>;
> + powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
> + reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ps8640_pins>;
> + vdd12-supply = <&mt6366_vrf12_reg>;
> + vdd33-supply = <&mt6366_vcn33_reg>;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + ps8640_in: endpoint {
> + remote-endpoint = <&dsi_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + ps8640_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + };
> + };
> + };
> +
> + aux-bus {
> + panel {
> + compatible = "edp-panel";
> + power-supply = <&pp3300_disp_x>;
> + backlight = <&backlight_lcd0>;
> +
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&ps8640_out>;
> + };
> + };
> + };
> + };
> + };
> +};
> +
> +&i2c1 {
> + i2c-scl-internal-delay-ns = <10000>;
> +
> + touchscreen: touchscreen@10 {
> + compatible = "hid-over-i2c";
> + reg = <0x10>;
> + interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&touchscreen_pins>;
> + post-power-on-delay-ms = <10>;
> + hid-descr-addr = <0x0001>;
> + vdd-supply = <&pp3300_s3>;
> + };
> +};
> +
> +&i2c4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c4_pins>;
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + proximity@28 {
> + compatible = "semtech,sx9324";
> + reg = <0x28>;
> + interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sar_sensor_pins>;
> + vdd-supply = <&mt6366_vio18_reg>;
> + svdd-supply = <&mt6366_vio18_reg>;
> + #io-channel-cells = <1>;
From the newest DTS coding style document:
The following order of properties in device nodes is preferred:
1. compatible
2. reg
3. ranges
4. Standard/common properties (defined by common bindings, e.g. without
vendor-prefixes)
5. Vendor-specific properties
6. status (if applicable)
7. Child nodes, where each node is preceded with a blank line
The "status" property is by default "okay", thus it can be omitted.
The above-described ordering follows this approach:
1. Most important properties start the node: compatible then bus addressing to
match unit address.
2. Each node will have common properties in similar place.
3. Status is the last information to annotate that device node is or is not
finished (board resources are needed).
#io-channel-cells goes after `reg` (same for the other instances) :-)
> + };
> +};
> +
> +&pio {
> + i2c4_pins: i2c4-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
> + <PINMUX_GPIO135__FUNC_SCL4>;
> + bias-disable;
> + drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
> + ps8640_pins: ps8640-pins {
> + pins-pwrdn-rst {
> + pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
> + <PINMUX_GPIO98__FUNC_GPIO98>;
> + output-low;
> + };
> + };
> +
> + sar_sensor_pins: sar-sensor-pins {
> + pins-irq {
> + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> new file mode 100644
> index 000000000000..9bb64353ca65
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> @@ -0,0 +1,57 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2022 Google LLC
> + */
> +
> +/dts-v1/;
> +#include "mt8186-corsola-krabby.dtsi"
> +
> +/ {
> + model = "Google Tentacool board";
> + compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
> + chassis-type = "laptop";
> +};
> +
> +/* Tentacool omits the pen. */
> +&gpio_keys {
> + status = "disabled";
> +};
> +
> +/* Tentacool omits the touchscreen; nothing else is on i2c1. */
> +&i2c1 {
> + status = "disabled";
> +};
> +
> +&keyboard_controller {
> + function-row-physmap = <
> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> + >;
> +
> + linux,keymap = <
> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> + CROS_STD_MAIN_KEYMAP
> + >;
> +};
> +
> +/* Tentacool omits the touchscreen. */
> +&touchscreen {
> + status = "disabled";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> new file mode 100644
> index 000000000000..c3ae6f9616c8
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> @@ -0,0 +1,24 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2023 Google LLC
> + */
> +
> +#include "mt8186-corsola-tentacool-sku327681.dts"
> +
> +/ {
> + compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
> +};
> +
> +/* This variant replaces only the trackpad controller. */
> +&i2c2 {
> + /delete-node/ trackpad@15;
Why are you deleting the trackpad@15 node?
You can simply override the compatible, or actually omit the compatible string
in the *.dtsi file, and set just that in each board *.dts.
dtsi:
trackpad_a: trackpad@15 {
/* Compatible is set in each board dts */
reg, interrupts, others
}
dts:
&trackpad_a {
compatible = "elan,ekth3000";
};
other dts:
&trackpad_a {
compatible = "hid-over-i2c";
};
> +
> + trackpad@15 {
> + compatible = "hid-over-i2c";
> + reg = <0x15>;
> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> + hid-descr-addr = <0x0001>;
> + vdd-supply = <&pp3300_s3>;
> + wakeup-source;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> new file mode 100644
> index 000000000000..26d3451a5e47
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> @@ -0,0 +1,44 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2022 Google LLC
> + */
> +
> +/dts-v1/;
> +#include "mt8186-corsola-krabby.dtsi"
> +
> +/ {
> + model = "Google Tentacruel board";
> + compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
> + "google,tentacruel-sku262145", "google,tentacruel-sku262144",
> + "google,tentacruel", "mediatek,mt8186";
> + chassis-type = "convertible";
> +};
> +
> +&keyboard_controller {
> + function-row-physmap = <
> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> + >;
> +
> + linux,keymap = <
> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> + CROS_STD_MAIN_KEYMAP
> + >;
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> new file mode 100644
> index 000000000000..447b57b12b41
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> @@ -0,0 +1,26 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright 2023 Google LLC
> + */
> +
> +#include "mt8186-corsola-tentacruel-sku262144.dts"
> +
> +/ {
> + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
> + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
> + "google,tentacruel", "mediatek,mt8186";
> +};
> +
> +/* This variant replaces only the trackpad controller. */
> +&i2c2 {
> + /delete-node/ trackpad@15;
> +
> + trackpad@15 {
> + compatible = "hid-over-i2c";
> + reg = <0x15>;
> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> + hid-descr-addr = <0x0001>;
> + vdd-supply = <&pp3300_s3>;
> + wakeup-source;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> new file mode 100644
> index 000000000000..8726b2916ef1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> @@ -0,0 +1,1719 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2022 MediaTek Inc.
> + */
> +/dts-v1/;
> +#include "mt8186.dtsi"
> +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
> +
> +/ {
> + aliases {
> + i2c0 = &i2c0;
> + i2c1 = &i2c1;
> + i2c2 = &i2c2;
> + i2c3 = &i2c3;
> + i2c5 = &i2c5;
> + mmc0 = &mmc0;
> + mmc1 = &mmc1;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@40000000 {
> + device_type = "memory";
> + /* The size should be filled in by the bootloader. */
> + reg = <0 0x40000000 0 0>;
> + };
> +
> + backlight_lcd0: backlight-lcd0 {
> + compatible = "pwm-backlight";
> + pwms = <&pwm0 0 500000>;
> + power-supply = <&ppvar_sys>;
> + enable-gpios = <&pio 152 0>;
> + brightness-levels = <0 1023>;
> + num-interpolated-steps = <1023>;
> + default-brightness-level = <576>;
> + };
> +
> + btsco: bt-sco {
Do you really need the phandle to bt-sco?
Also, this node describes a codec, so: "bt-sco-codec" please!
> + compatible = "linux,bt-sco";
> + #sound-dai-cells = <0>;
> + };
> +
> + dmic_codec: dmic-codec {
This phandle is unused...
..snip..
> +
> +&adsp {
> + memory-region = <&adsp_dma_mem>, <&adsp_mem>;
> + status = "disabled"; /* causes stall */
This is a firmware issue: once the correct firmware is uploaded to linux-firmware
the dsp node can get enabled... so it we make sure that this happens before this
devicetree gets picked, we can avoid a second commit enabling audio.
After all, since we *want to* use the Xtensa DSP for audio, without it booted
sound won't work *anyway*.... so having the firmware in place can also be seen
as a direct dependency of the entire audio functionality.
P.S.: The FW that is distributed with ChromeOS works just fine!
> +};
> +
> +&afe {
> + i2s0-share = "I2S1";
> + i2s3-share = "I2S2";
> + status = "okay";
> +};
> +
..snip..
> +&i2c2 {
> + pinctrl-names = "default";
> + /*
> + * Trackpad pin put here to work around second source components
> + * sharing the pinmux in steelix designs.
> + */
> + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
There's no choice for now... even if this is not beautiful to see... but it's still
ok for me because we can revisit this later when the HW Prober mechanism will be
upstreamed.
> + clock-frequency = <400000>;
> + i2c-scl-internal-delay-ns = <10000>;
> + status = "okay";
> +
> + trackpad@15 {
> + compatible = "elan,ekth3000";
> + reg = <0x15>;
> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> + vcc-supply = <&pp3300_s3>;
> + wakeup-source;
> + };
> +};
> +
Thanks,
Angelo
On Mon, Dec 4, 2023 at 11:27 PM AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com> wrote:
>
> Il 04/12/23 09:40, Chen-Yu Tsai ha scritto:
> > Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> > Krabby design.
> >
> > Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> > convertible device with touchscreen and stylus.
> >
> > Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> > device. It does not have a touchscreen or stylus.
> >
> > The two devices both have two variants. The difference is a second
> > source touchpad controller that shares the same address as the original,
> > but is incompatible.
> >
> > The extra SKU IDs for the Tentacruel devices map to different sensor
> > components attached to the Embedded Controller. These are not visible
> > to the main processor.
> >
> > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> > Acked-by: Conor Dooley <conor.dooley@microchip.com>
> > ---
> > Changes since v2:
> > - Picked up Conor's ack
> > - Rename touchpad to trackpad
> > - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> > source trackpad
> >
> > Changes since v1:
> > - Reorder SKU numbers in descending order.
> > - Fixed pinconfig node names
> > - Moved pinctrl-* properties after interrupts-*
> > - Switched to interrupts-extended for external components
> > - Marked ADSP as explicitly disabled, with a comment explaining that it
> > stalls the system
> > - Renamed "touchpad" to "trackpad"
> > - Dropped bogus "no-laneswap" property from it6505 node
> > - Moved "realtek,jd-src" property to after all the regulator supplies
> > - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> > - Renamed "vgpu" regulator name to allow coupling, with a comment
> > containing the name used in the design
> > - Renamed "cr50" node name to "tpm"
> > - Moved trackpad_pins reference up to i2c2; workaround for second source
> > component resource sharing.
> > - Fix copyright year
> > - Fixed touchscreen supply name
> >
> > arch/arm64/boot/dts/mediatek/Makefile | 4 +
> > .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> > .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> > .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> > .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> > .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> > .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
> > 7 files changed, 2003 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > index e6e7592a3645..442af61b1305 100644
> > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > new file mode 100644
> > index 000000000000..9b2b64525961
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > @@ -0,0 +1,129 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2022 Google LLC
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt8186-corsola.dtsi"
> > +#include <dt-bindings/gpio/gpio.h>
> > +
> > +/ {
> > + aliases {
> > + i2c4 = &i2c4;
> > + };
> > +};
> > +
> > +&dsi_out {
> > + remote-endpoint = <&ps8640_in>;
> > +};
> > +
> > +&i2c0 {
> > + clock-frequency = <400000>;
> > +
> > + ps8640: edp-bridge@8 {
> > + compatible = "parade,ps8640";
> > + reg = <0x8>;
> > + powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
> > + reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&ps8640_pins>;
> > + vdd12-supply = <&mt6366_vrf12_reg>;
> > + vdd33-supply = <&mt6366_vcn33_reg>;
> > +
> > + ports {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + port@0 {
> > + reg = <0>;
> > +
> > + ps8640_in: endpoint {
> > + remote-endpoint = <&dsi_out>;
> > + };
> > + };
> > +
> > + port@1 {
> > + reg = <1>;
> > +
> > + ps8640_out: endpoint {
> > + remote-endpoint = <&panel_in>;
> > + };
> > + };
> > + };
> > +
> > + aux-bus {
> > + panel {
> > + compatible = "edp-panel";
> > + power-supply = <&pp3300_disp_x>;
> > + backlight = <&backlight_lcd0>;
> > +
> > + port {
> > + panel_in: endpoint {
> > + remote-endpoint = <&ps8640_out>;
> > + };
> > + };
> > + };
> > + };
> > + };
> > +};
> > +
> > +&i2c1 {
> > + i2c-scl-internal-delay-ns = <10000>;
> > +
> > + touchscreen: touchscreen@10 {
> > + compatible = "hid-over-i2c";
> > + reg = <0x10>;
> > + interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&touchscreen_pins>;
> > + post-power-on-delay-ms = <10>;
> > + hid-descr-addr = <0x0001>;
> > + vdd-supply = <&pp3300_s3>;
> > + };
> > +};
> > +
> > +&i2c4 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&i2c4_pins>;
> > + clock-frequency = <400000>;
> > + status = "okay";
> > +
> > + proximity@28 {
> > + compatible = "semtech,sx9324";
> > + reg = <0x28>;
> > + interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&sar_sensor_pins>;
> > + vdd-supply = <&mt6366_vio18_reg>;
> > + svdd-supply = <&mt6366_vio18_reg>;
> > + #io-channel-cells = <1>;
>
> From the newest DTS coding style document:
>
> The following order of properties in device nodes is preferred:
>
> 1. compatible
> 2. reg
> 3. ranges
> 4. Standard/common properties (defined by common bindings, e.g. without
> vendor-prefixes)
> 5. Vendor-specific properties
> 6. status (if applicable)
> 7. Child nodes, where each node is preceded with a blank line
>
> The "status" property is by default "okay", thus it can be omitted.
>
> The above-described ordering follows this approach:
>
> 1. Most important properties start the node: compatible then bus addressing to
> match unit address.
> 2. Each node will have common properties in similar place.
> 3. Status is the last information to annotate that device node is or is not
> finished (board resources are needed).
Wishing for a checking tool now. :p
> #io-channel-cells goes after `reg` (same for the other instances) :-)
Ack (though it looks weird).
> > + };
> > +};
> > +
> > +&pio {
> > + i2c4_pins: i2c4-pins {
> > + pins-bus {
> > + pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
> > + <PINMUX_GPIO135__FUNC_SCL4>;
> > + bias-disable;
> > + drive-strength = <4>;
> > + input-enable;
> > + };
> > + };
> > +
> > + ps8640_pins: ps8640-pins {
> > + pins-pwrdn-rst {
> > + pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
> > + <PINMUX_GPIO98__FUNC_GPIO98>;
> > + output-low;
> > + };
> > + };
> > +
> > + sar_sensor_pins: sar-sensor-pins {
> > + pins-irq {
> > + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
> > + input-enable;
> > + bias-pull-up;
> > + };
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > new file mode 100644
> > index 000000000000..9bb64353ca65
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > @@ -0,0 +1,57 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2022 Google LLC
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt8186-corsola-krabby.dtsi"
> > +
> > +/ {
> > + model = "Google Tentacool board";
> > + compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
> > + chassis-type = "laptop";
> > +};
> > +
> > +/* Tentacool omits the pen. */
> > +&gpio_keys {
> > + status = "disabled";
> > +};
> > +
> > +/* Tentacool omits the touchscreen; nothing else is on i2c1. */
> > +&i2c1 {
> > + status = "disabled";
> > +};
> > +
> > +&keyboard_controller {
> > + function-row-physmap = <
> > + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> > + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> > + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> > + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> > + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> > + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> > + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> > + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> > + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> > + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> > + >;
> > +
> > + linux,keymap = <
> > + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> > + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> > + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> > + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> > + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> > + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> > + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> > + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> > + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> > + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> > + CROS_STD_MAIN_KEYMAP
> > + >;
> > +};
> > +
> > +/* Tentacool omits the touchscreen. */
> > +&touchscreen {
> > + status = "disabled";
> > +};
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > new file mode 100644
> > index 000000000000..c3ae6f9616c8
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > @@ -0,0 +1,24 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2023 Google LLC
> > + */
> > +
> > +#include "mt8186-corsola-tentacool-sku327681.dts"
> > +
> > +/ {
> > + compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
> > +};
> > +
> > +/* This variant replaces only the trackpad controller. */
> > +&i2c2 {
> > + /delete-node/ trackpad@15;
>
> Why are you deleting the trackpad@15 node?
>
> You can simply override the compatible, or actually omit the compatible string
> in the *.dtsi file, and set just that in each board *.dts.
>
> dtsi:
> trackpad_a: trackpad@15 {
> /* Compatible is set in each board dts */
> reg, interrupts, others
> }
>
> dts:
>
> &trackpad_a {
> compatible = "elan,ekth3000";
> };
The original trackpad@15 comes from the base design and is used for all
models other than the ones with the conflicting component. Hence I believe
it should live in the base .dtsi.
The delete-node makes it much less likely to have any lingering properties.
These are not nodes that just differ in compatible strings like DSI panels.
They have incompatible bindings. For example, elan,ekth3000 uses "vcc-supply",
while "hid-over-i2c" uses "vdd-supply".
And going back to my previous argument, the base design used one specific
model which is carried over to all the other models.
Suppose I add a phandle to the original trackpad, and do
/delete-node/ &trackpad;
Would that be better?
> other dts:
>
> &trackpad_a {
> compatible = "hid-over-i2c";
> };
>
> > +
> > + trackpad@15 {
> > + compatible = "hid-over-i2c";
> > + reg = <0x15>;
> > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > + hid-descr-addr = <0x0001>;
> > + vdd-supply = <&pp3300_s3>;
> > + wakeup-source;
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > new file mode 100644
> > index 000000000000..26d3451a5e47
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > @@ -0,0 +1,44 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2022 Google LLC
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt8186-corsola-krabby.dtsi"
> > +
> > +/ {
> > + model = "Google Tentacruel board";
> > + compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
> > + "google,tentacruel-sku262145", "google,tentacruel-sku262144",
> > + "google,tentacruel", "mediatek,mt8186";
> > + chassis-type = "convertible";
> > +};
> > +
> > +&keyboard_controller {
> > + function-row-physmap = <
> > + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> > + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> > + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> > + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> > + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> > + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> > + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> > + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> > + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> > + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> > + >;
> > +
> > + linux,keymap = <
> > + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> > + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> > + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> > + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> > + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> > + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> > + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> > + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> > + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> > + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> > + CROS_STD_MAIN_KEYMAP
> > + >;
> > +};
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > new file mode 100644
> > index 000000000000..447b57b12b41
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > @@ -0,0 +1,26 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright 2023 Google LLC
> > + */
> > +
> > +#include "mt8186-corsola-tentacruel-sku262144.dts"
> > +
> > +/ {
> > + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
> > + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
> > + "google,tentacruel", "mediatek,mt8186";
> > +};
> > +
> > +/* This variant replaces only the trackpad controller. */
> > +&i2c2 {
> > + /delete-node/ trackpad@15;
> > +
> > + trackpad@15 {
> > + compatible = "hid-over-i2c";
> > + reg = <0x15>;
> > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > + hid-descr-addr = <0x0001>;
> > + vdd-supply = <&pp3300_s3>;
> > + wakeup-source;
> > + };
> > +};
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > new file mode 100644
> > index 000000000000..8726b2916ef1
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > @@ -0,0 +1,1719 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright (C) 2022 MediaTek Inc.
> > + */
> > +/dts-v1/;
> > +#include "mt8186.dtsi"
> > +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/input/gpio-keys.h>
> > +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
> > +
> > +/ {
> > + aliases {
> > + i2c0 = &i2c0;
> > + i2c1 = &i2c1;
> > + i2c2 = &i2c2;
> > + i2c3 = &i2c3;
> > + i2c5 = &i2c5;
> > + mmc0 = &mmc0;
> > + mmc1 = &mmc1;
> > + serial0 = &uart0;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + memory@40000000 {
> > + device_type = "memory";
> > + /* The size should be filled in by the bootloader. */
> > + reg = <0 0x40000000 0 0>;
> > + };
> > +
> > + backlight_lcd0: backlight-lcd0 {
> > + compatible = "pwm-backlight";
> > + pwms = <&pwm0 0 500000>;
> > + power-supply = <&ppvar_sys>;
> > + enable-gpios = <&pio 152 0>;
> > + brightness-levels = <0 1023>;
> > + num-interpolated-steps = <1023>;
> > + default-brightness-level = <576>;
> > + };
> > +
> > + btsco: bt-sco {
>
> Do you really need the phandle to bt-sco?
No. But the sound node probably should be referencing it and the dmic
node via DT instead of hardcoding the DAI and codec names in the machine
driver.
Anyway, will remove the label for now.
> Also, this node describes a codec, so: "bt-sco-codec" please!
Ack.
> > + compatible = "linux,bt-sco";
> > + #sound-dai-cells = <0>;
> > + };
> > +
> > + dmic_codec: dmic-codec {
>
> This phandle is unused...
Removed.
> ..snip..
>
> > +
> > +&adsp {
> > + memory-region = <&adsp_dma_mem>, <&adsp_mem>;
> > + status = "disabled"; /* causes stall */
>
> This is a firmware issue: once the correct firmware is uploaded to linux-firmware
> the dsp node can get enabled... so it we make sure that this happens before this
> devicetree gets picked, we can avoid a second commit enabling audio.
>
> After all, since we *want to* use the Xtensa DSP for audio, without it booted
> sound won't work *anyway*.... so having the firmware in place can also be seen
> as a direct dependency of the entire audio functionality.
>
> P.S.: The FW that is distributed with ChromeOS works just fine!
I'll give that a try.
> > +};
> > +
> > +&afe {
> > + i2s0-share = "I2S1";
> > + i2s3-share = "I2S2";
> > + status = "okay";
> > +};
> > +
>
> ..snip..
>
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + /*
> > + * Trackpad pin put here to work around second source components
> > + * sharing the pinmux in steelix designs.
> > + */
> > + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
>
> There's no choice for now... even if this is not beautiful to see... but it's still
> ok for me because we can revisit this later when the HW Prober mechanism will be
> upstreamed.
Yup. Working on that.
> > + clock-frequency = <400000>;
> > + i2c-scl-internal-delay-ns = <10000>;
> > + status = "okay";
> > +
> > + trackpad@15 {
> > + compatible = "elan,ekth3000";
> > + reg = <0x15>;
> > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > + vcc-supply = <&pp3300_s3>;
> > + wakeup-source;
> > + };
> > +};
> > +
>
> Thanks,
> Angelo
Thanks for the review again.
ChenYu
On Mon, Dec 04, 2023 at 01:55:06PM +0200, Eugen Hristev wrote:
> Hello Chen-Yu,
>
> On 12/4/23 10:40, Chen-Yu Tsai wrote:
> > Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> > Krabby design.
> >
> > Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> > convertible device with touchscreen and stylus.
> >
> > Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> > device. It does not have a touchscreen or stylus.
> >
> > The two devices both have two variants. The difference is a second
> > source touchpad controller that shares the same address as the original,
> > but is incompatible.
> >
> > The extra SKU IDs for the Tentacruel devices map to different sensor
> > components attached to the Embedded Controller. These are not visible
> > to the main processor.
> >
> > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> > Acked-by: Conor Dooley <conor.dooley@microchip.com>
> > ---
> > Changes since v2:
> > - Picked up Conor's ack
> > - Rename touchpad to trackpad
> > - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> > source trackpad
> >
> > Changes since v1:
> > - Reorder SKU numbers in descending order.
> > - Fixed pinconfig node names
> > - Moved pinctrl-* properties after interrupts-*
> > - Switched to interrupts-extended for external components
> > - Marked ADSP as explicitly disabled, with a comment explaining that it
> > stalls the system
> > - Renamed "touchpad" to "trackpad"
> > - Dropped bogus "no-laneswap" property from it6505 node
> > - Moved "realtek,jd-src" property to after all the regulator supplies
> > - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> > - Renamed "vgpu" regulator name to allow coupling, with a comment
> > containing the name used in the design
> > - Renamed "cr50" node name to "tpm"
> > - Moved trackpad_pins reference up to i2c2; workaround for second source
> > component resource sharing.
> > - Fix copyright year
> > - Fixed touchscreen supply name
> >
> > arch/arm64/boot/dts/mediatek/Makefile | 4 +
> > .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> > .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> > .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> > .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> > .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> > .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
> > 7 files changed, 2003 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
[...]
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > new file mode 100644
> > index 000000000000..8726b2916ef1
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > @@ -0,0 +1,1719 @@
[...]
> > + sound: sound {
> > + compatible = "mediatek,mt8186-mt6366-rt1019-rt5682s-sound";
> > + pinctrl-names = "aud_clk_mosi_off",
> > + "aud_clk_mosi_on",
> > + "aud_clk_miso_off",
> > + "aud_clk_miso_on",
> > + "aud_dat_miso_off",
> > + "aud_dat_miso_on",
> > + "aud_dat_mosi_off",
> > + "aud_dat_mosi_on",
> > + "aud_gpio_i2s0_off",
> > + "aud_gpio_i2s0_on",
> > + "aud_gpio_i2s1_off",
> > + "aud_gpio_i2s1_on",
> > + "aud_gpio_i2s2_off",
> > + "aud_gpio_i2s2_on",
> > + "aud_gpio_i2s3_off",
> > + "aud_gpio_i2s3_on",
> > + "aud_gpio_tdm_off",
> > + "aud_gpio_tdm_on",
> > + "aud_gpio_pcm_off",
> > + "aud_gpio_pcm_on",
> > + "aud_gpio_dmic_sec";
> > + pinctrl-0 = <&aud_clk_mosi_off>;
> > + pinctrl-1 = <&aud_clk_mosi_on>;
> > + pinctrl-2 = <&aud_clk_miso_off>;
> > + pinctrl-3 = <&aud_clk_miso_on>;
> > + pinctrl-4 = <&aud_dat_miso_off>;
> > + pinctrl-5 = <&aud_dat_miso_on>;
> > + pinctrl-6 = <&aud_dat_mosi_off>;
> > + pinctrl-7 = <&aud_dat_mosi_on>;
> > + pinctrl-8 = <&aud_gpio_i2s0_off>;
> > + pinctrl-9 = <&aud_gpio_i2s0_on>;
> > + pinctrl-10 = <&aud_gpio_i2s1_off>;
> > + pinctrl-11 = <&aud_gpio_i2s1_on>;
> > + pinctrl-12 = <&aud_gpio_i2s2_off>;
> > + pinctrl-13 = <&aud_gpio_i2s2_on>;
> > + pinctrl-14 = <&aud_gpio_i2s3_off>;
> > + pinctrl-15 = <&aud_gpio_i2s3_on>;
> > + pinctrl-16 = <&aud_gpio_tdm_off>;
> > + pinctrl-17 = <&aud_gpio_tdm_on>;
>
> These two above bring errors, as discussed
Looking at the machine driver code, it seems OK to remove them. So I
will.
> > + pinctrl-18 = <&aud_gpio_pcm_off>;
> > + pinctrl-19 = <&aud_gpio_pcm_on>;
> > + pinctrl-20 = <&aud_gpio_dmic_sec>;
> > + mediatek,adsp = <&adsp>;
> > + mediatek,platform = <&afe>;
> > +
> > + playback-codecs {
> > + sound-dai = <&it6505dptx>, <&rt1019p>;
> > + };
> > +
> > + headset-codec {
> > + sound-dai = <&rt5682s 0>;
> > + };
> > + };
[...]
> > +&afe {
> > + i2s0-share = "I2S1";
> > + i2s3-share = "I2S2";
>
> These i2sX-share are not documented.
Looks like this got handled directly in the machine driver.
Will remove.
> > + status = "okay";
> > +};
[...]
> > +&i2c2 {
> > + pinctrl-names = "default";
> > + /*
> > + * Trackpad pin put here to work around second source components
> > + * sharing the pinmux in steelix designs.
> > + */
> > + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
>
> While this makes things better, it's not correct. The i2c2 bus does not use the
> trackpad pin. I would believe a better way is to have a node that holds both
> trackpads and claims the pin for both at once. And that node not being the i2c bus
> as there could be more devices on the bus and the pin would be taken regardless of
> any trackpad probing , which is not right.
That is still a workaround, and it also doesn't work because there are
no bindings nor code for the extra device node level.
> Another option is to disable parallel probing for the trackpads, such that when one
> fails to probe, the pin is released and can be taken by the other one.
We thought about this but this workaround would impact everyone else not
dealing with second source components.
[...]
> > + aud_gpio_tdm_off: aud-gpio-tdm-off-pins { };
> > +
> > + aud_gpio_tdm_on: aud-gpio-tdm-on-pins { };
>
> Guess have to remove these two empty pinctrls.
Yes. I'll try that. Looking at the code it should work.
Thanks for the review
ChenYu
On Thu, Dec 7, 2023 at 2:28 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
>
> On Mon, Dec 4, 2023 at 11:27 PM AngeloGioacchino Del Regno
> <angelogioacchino.delregno@collabora.com> wrote:
> >
> > Il 04/12/23 09:40, Chen-Yu Tsai ha scritto:
> > > Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> > > Krabby design.
> > >
> > > Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> > > convertible device with touchscreen and stylus.
> > >
> > > Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> > > device. It does not have a touchscreen or stylus.
> > >
> > > The two devices both have two variants. The difference is a second
> > > source touchpad controller that shares the same address as the original,
> > > but is incompatible.
> > >
> > > The extra SKU IDs for the Tentacruel devices map to different sensor
> > > components attached to the Embedded Controller. These are not visible
> > > to the main processor.
> > >
> > > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> > > Acked-by: Conor Dooley <conor.dooley@microchip.com>
> > > ---
> > > Changes since v2:
> > > - Picked up Conor's ack
> > > - Rename touchpad to trackpad
> > > - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> > > source trackpad
> > >
> > > Changes since v1:
> > > - Reorder SKU numbers in descending order.
> > > - Fixed pinconfig node names
> > > - Moved pinctrl-* properties after interrupts-*
> > > - Switched to interrupts-extended for external components
> > > - Marked ADSP as explicitly disabled, with a comment explaining that it
> > > stalls the system
> > > - Renamed "touchpad" to "trackpad"
> > > - Dropped bogus "no-laneswap" property from it6505 node
> > > - Moved "realtek,jd-src" property to after all the regulator supplies
> > > - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> > > - Renamed "vgpu" regulator name to allow coupling, with a comment
> > > containing the name used in the design
> > > - Renamed "cr50" node name to "tpm"
> > > - Moved trackpad_pins reference up to i2c2; workaround for second source
> > > component resource sharing.
> > > - Fix copyright year
> > > - Fixed touchscreen supply name
> > >
> > > arch/arm64/boot/dts/mediatek/Makefile | 4 +
> > > .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> > > .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> > > .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> > > .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> > > .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> > > .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
> > > 7 files changed, 2003 insertions(+)
> > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > >
> > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > > index e6e7592a3645..442af61b1305 100644
> > > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > > @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
> > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
> > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
> > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
> > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
> > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
> > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > > new file mode 100644
> > > index 000000000000..9b2b64525961
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > > @@ -0,0 +1,129 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/*
> > > + * Copyright 2022 Google LLC
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include "mt8186-corsola.dtsi"
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +
> > > +/ {
> > > + aliases {
> > > + i2c4 = &i2c4;
> > > + };
> > > +};
> > > +
> > > +&dsi_out {
> > > + remote-endpoint = <&ps8640_in>;
> > > +};
> > > +
> > > +&i2c0 {
> > > + clock-frequency = <400000>;
> > > +
> > > + ps8640: edp-bridge@8 {
> > > + compatible = "parade,ps8640";
> > > + reg = <0x8>;
> > > + powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
> > > + reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&ps8640_pins>;
> > > + vdd12-supply = <&mt6366_vrf12_reg>;
> > > + vdd33-supply = <&mt6366_vcn33_reg>;
> > > +
> > > + ports {
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > +
> > > + port@0 {
> > > + reg = <0>;
> > > +
> > > + ps8640_in: endpoint {
> > > + remote-endpoint = <&dsi_out>;
> > > + };
> > > + };
> > > +
> > > + port@1 {
> > > + reg = <1>;
> > > +
> > > + ps8640_out: endpoint {
> > > + remote-endpoint = <&panel_in>;
> > > + };
> > > + };
> > > + };
> > > +
> > > + aux-bus {
> > > + panel {
> > > + compatible = "edp-panel";
> > > + power-supply = <&pp3300_disp_x>;
> > > + backlight = <&backlight_lcd0>;
> > > +
> > > + port {
> > > + panel_in: endpoint {
> > > + remote-endpoint = <&ps8640_out>;
> > > + };
> > > + };
> > > + };
> > > + };
> > > + };
> > > +};
> > > +
> > > +&i2c1 {
> > > + i2c-scl-internal-delay-ns = <10000>;
> > > +
> > > + touchscreen: touchscreen@10 {
> > > + compatible = "hid-over-i2c";
> > > + reg = <0x10>;
> > > + interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&touchscreen_pins>;
> > > + post-power-on-delay-ms = <10>;
> > > + hid-descr-addr = <0x0001>;
> > > + vdd-supply = <&pp3300_s3>;
> > > + };
> > > +};
> > > +
> > > +&i2c4 {
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&i2c4_pins>;
> > > + clock-frequency = <400000>;
> > > + status = "okay";
> > > +
> > > + proximity@28 {
> > > + compatible = "semtech,sx9324";
> > > + reg = <0x28>;
> > > + interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&sar_sensor_pins>;
> > > + vdd-supply = <&mt6366_vio18_reg>;
> > > + svdd-supply = <&mt6366_vio18_reg>;
> > > + #io-channel-cells = <1>;
> >
> > From the newest DTS coding style document:
> >
> > The following order of properties in device nodes is preferred:
> >
> > 1. compatible
> > 2. reg
> > 3. ranges
> > 4. Standard/common properties (defined by common bindings, e.g. without
> > vendor-prefixes)
> > 5. Vendor-specific properties
> > 6. status (if applicable)
> > 7. Child nodes, where each node is preceded with a blank line
> >
> > The "status" property is by default "okay", thus it can be omitted.
> >
> > The above-described ordering follows this approach:
> >
> > 1. Most important properties start the node: compatible then bus addressing to
> > match unit address.
> > 2. Each node will have common properties in similar place.
> > 3. Status is the last information to annotate that device node is or is not
> > finished (board resources are needed).
>
> Wishing for a checking tool now. :p
>
> > #io-channel-cells goes after `reg` (same for the other instances) :-)
>
> Ack (though it looks weird).
>
> > > + };
> > > +};
> > > +
> > > +&pio {
> > > + i2c4_pins: i2c4-pins {
> > > + pins-bus {
> > > + pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
> > > + <PINMUX_GPIO135__FUNC_SCL4>;
> > > + bias-disable;
> > > + drive-strength = <4>;
> > > + input-enable;
> > > + };
> > > + };
> > > +
> > > + ps8640_pins: ps8640-pins {
> > > + pins-pwrdn-rst {
> > > + pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
> > > + <PINMUX_GPIO98__FUNC_GPIO98>;
> > > + output-low;
> > > + };
> > > + };
> > > +
> > > + sar_sensor_pins: sar-sensor-pins {
> > > + pins-irq {
> > > + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
> > > + input-enable;
> > > + bias-pull-up;
> > > + };
> > > + };
> > > +};
> > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > > new file mode 100644
> > > index 000000000000..9bb64353ca65
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > > @@ -0,0 +1,57 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/*
> > > + * Copyright 2022 Google LLC
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include "mt8186-corsola-krabby.dtsi"
> > > +
> > > +/ {
> > > + model = "Google Tentacool board";
> > > + compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
> > > + chassis-type = "laptop";
> > > +};
> > > +
> > > +/* Tentacool omits the pen. */
> > > +&gpio_keys {
> > > + status = "disabled";
> > > +};
> > > +
> > > +/* Tentacool omits the touchscreen; nothing else is on i2c1. */
> > > +&i2c1 {
> > > + status = "disabled";
> > > +};
> > > +
> > > +&keyboard_controller {
> > > + function-row-physmap = <
> > > + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> > > + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> > > + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> > > + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> > > + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> > > + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> > > + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> > > + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> > > + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> > > + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> > > + >;
> > > +
> > > + linux,keymap = <
> > > + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> > > + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> > > + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> > > + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> > > + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> > > + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> > > + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> > > + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> > > + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> > > + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> > > + CROS_STD_MAIN_KEYMAP
> > > + >;
> > > +};
> > > +
> > > +/* Tentacool omits the touchscreen. */
> > > +&touchscreen {
> > > + status = "disabled";
> > > +};
> > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > > new file mode 100644
> > > index 000000000000..c3ae6f9616c8
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > > @@ -0,0 +1,24 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/*
> > > + * Copyright 2023 Google LLC
> > > + */
> > > +
> > > +#include "mt8186-corsola-tentacool-sku327681.dts"
> > > +
> > > +/ {
> > > + compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
> > > +};
> > > +
> > > +/* This variant replaces only the trackpad controller. */
> > > +&i2c2 {
> > > + /delete-node/ trackpad@15;
> >
> > Why are you deleting the trackpad@15 node?
> >
> > You can simply override the compatible, or actually omit the compatible string
> > in the *.dtsi file, and set just that in each board *.dts.
> >
> > dtsi:
> > trackpad_a: trackpad@15 {
> > /* Compatible is set in each board dts */
> > reg, interrupts, others
> > }
> >
> > dts:
> >
> > &trackpad_a {
> > compatible = "elan,ekth3000";
> > };
>
> The original trackpad@15 comes from the base design and is used for all
> models other than the ones with the conflicting component. Hence I believe
> it should live in the base .dtsi.
>
> The delete-node makes it much less likely to have any lingering properties.
> These are not nodes that just differ in compatible strings like DSI panels.
> They have incompatible bindings. For example, elan,ekth3000 uses "vcc-supply",
> while "hid-over-i2c" uses "vdd-supply".
>
> And going back to my previous argument, the base design used one specific
> model which is carried over to all the other models.
>
> Suppose I add a phandle to the original trackpad, and do
>
> /delete-node/ &trackpad;
>
> Would that be better?
>
> > other dts:
> >
> > &trackpad_a {
> > compatible = "hid-over-i2c";
> > };
> >
> > > +
> > > + trackpad@15 {
> > > + compatible = "hid-over-i2c";
> > > + reg = <0x15>;
> > > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > > + hid-descr-addr = <0x0001>;
> > > + vdd-supply = <&pp3300_s3>;
> > > + wakeup-source;
> > > + };
> > > +};
> > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > > new file mode 100644
> > > index 000000000000..26d3451a5e47
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > > @@ -0,0 +1,44 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/*
> > > + * Copyright 2022 Google LLC
> > > + */
> > > +
> > > +/dts-v1/;
> > > +#include "mt8186-corsola-krabby.dtsi"
> > > +
> > > +/ {
> > > + model = "Google Tentacruel board";
> > > + compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
> > > + "google,tentacruel-sku262145", "google,tentacruel-sku262144",
> > > + "google,tentacruel", "mediatek,mt8186";
> > > + chassis-type = "convertible";
> > > +};
> > > +
> > > +&keyboard_controller {
> > > + function-row-physmap = <
> > > + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> > > + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> > > + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> > > + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> > > + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> > > + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> > > + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> > > + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> > > + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> > > + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> > > + >;
> > > +
> > > + linux,keymap = <
> > > + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> > > + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> > > + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> > > + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> > > + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> > > + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> > > + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> > > + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> > > + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> > > + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> > > + CROS_STD_MAIN_KEYMAP
> > > + >;
> > > +};
> > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > > new file mode 100644
> > > index 000000000000..447b57b12b41
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > > @@ -0,0 +1,26 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/*
> > > + * Copyright 2023 Google LLC
> > > + */
> > > +
> > > +#include "mt8186-corsola-tentacruel-sku262144.dts"
> > > +
> > > +/ {
> > > + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
> > > + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
> > > + "google,tentacruel", "mediatek,mt8186";
> > > +};
> > > +
> > > +/* This variant replaces only the trackpad controller. */
> > > +&i2c2 {
> > > + /delete-node/ trackpad@15;
> > > +
> > > + trackpad@15 {
> > > + compatible = "hid-over-i2c";
> > > + reg = <0x15>;
> > > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > > + hid-descr-addr = <0x0001>;
> > > + vdd-supply = <&pp3300_s3>;
> > > + wakeup-source;
> > > + };
> > > +};
> > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > > new file mode 100644
> > > index 000000000000..8726b2916ef1
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > > @@ -0,0 +1,1719 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/*
> > > + * Copyright (C) 2022 MediaTek Inc.
> > > + */
> > > +/dts-v1/;
> > > +#include "mt8186.dtsi"
> > > +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> > > +#include <dt-bindings/gpio/gpio.h>
> > > +#include <dt-bindings/input/input.h>
> > > +#include <dt-bindings/input/gpio-keys.h>
> > > +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
> > > +
> > > +/ {
> > > + aliases {
> > > + i2c0 = &i2c0;
> > > + i2c1 = &i2c1;
> > > + i2c2 = &i2c2;
> > > + i2c3 = &i2c3;
> > > + i2c5 = &i2c5;
> > > + mmc0 = &mmc0;
> > > + mmc1 = &mmc1;
> > > + serial0 = &uart0;
> > > + };
> > > +
> > > + chosen {
> > > + stdout-path = "serial0:115200n8";
> > > + };
> > > +
> > > + memory@40000000 {
> > > + device_type = "memory";
> > > + /* The size should be filled in by the bootloader. */
> > > + reg = <0 0x40000000 0 0>;
> > > + };
> > > +
> > > + backlight_lcd0: backlight-lcd0 {
> > > + compatible = "pwm-backlight";
> > > + pwms = <&pwm0 0 500000>;
> > > + power-supply = <&ppvar_sys>;
> > > + enable-gpios = <&pio 152 0>;
> > > + brightness-levels = <0 1023>;
> > > + num-interpolated-steps = <1023>;
> > > + default-brightness-level = <576>;
> > > + };
> > > +
> > > + btsco: bt-sco {
> >
> > Do you really need the phandle to bt-sco?
>
> No. But the sound node probably should be referencing it and the dmic
> node via DT instead of hardcoding the DAI and codec names in the machine
> driver.
>
> Anyway, will remove the label for now.
>
> > Also, this node describes a codec, so: "bt-sco-codec" please!
>
> Ack.
>
> > > + compatible = "linux,bt-sco";
> > > + #sound-dai-cells = <0>;
> > > + };
> > > +
> > > + dmic_codec: dmic-codec {
> >
> > This phandle is unused...
>
> Removed.
>
> > ..snip..
> >
> > > +
> > > +&adsp {
> > > + memory-region = <&adsp_dma_mem>, <&adsp_mem>;
> > > + status = "disabled"; /* causes stall */
> >
> > This is a firmware issue: once the correct firmware is uploaded to linux-firmware
> > the dsp node can get enabled... so it we make sure that this happens before this
> > devicetree gets picked, we can avoid a second commit enabling audio.
> >
> > After all, since we *want to* use the Xtensa DSP for audio, without it booted
> > sound won't work *anyway*.... so having the firmware in place can also be seen
> > as a direct dependency of the entire audio functionality.
> >
> > P.S.: The FW that is distributed with ChromeOS works just fine!
>
> I'll give that a try.
I have:
sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
sof-audio-of-mt8186 10680000.adsp: unknown sof_ext_man header type 3 size 0x30
sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
and it's still hanging.
And FTR, I think sound is also blocked on the it6505 audio support series.
ChenYu
> > > +};
> > > +
> > > +&afe {
> > > + i2s0-share = "I2S1";
> > > + i2s3-share = "I2S2";
> > > + status = "okay";
> > > +};
> > > +
> >
> > ..snip..
> >
> > > +&i2c2 {
> > > + pinctrl-names = "default";
> > > + /*
> > > + * Trackpad pin put here to work around second source components
> > > + * sharing the pinmux in steelix designs.
> > > + */
> > > + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
> >
> > There's no choice for now... even if this is not beautiful to see... but it's still
> > ok for me because we can revisit this later when the HW Prober mechanism will be
> > upstreamed.
>
> Yup. Working on that.
>
> > > + clock-frequency = <400000>;
> > > + i2c-scl-internal-delay-ns = <10000>;
> > > + status = "okay";
> > > +
> > > + trackpad@15 {
> > > + compatible = "elan,ekth3000";
> > > + reg = <0x15>;
> > > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > > + vcc-supply = <&pp3300_s3>;
> > > + wakeup-source;
> > > + };
> > > +};
> > > +
> >
> > Thanks,
> > Angelo
>
> Thanks for the review again.
>
> ChenYu
On Thu, Dec 7, 2023 at 8:23 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
>
> On Thu, Dec 7, 2023 at 2:28 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
> >
> > On Mon, Dec 4, 2023 at 11:27 PM AngeloGioacchino Del Regno
> > <angelogioacchino.delregno@collabora.com> wrote:
> > >
> > > Il 04/12/23 09:40, Chen-Yu Tsai ha scritto:
> > > > Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> > > > Krabby design.
> > > >
> > > > Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> > > > convertible device with touchscreen and stylus.
> > > >
> > > > Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> > > > device. It does not have a touchscreen or stylus.
> > > >
> > > > The two devices both have two variants. The difference is a second
> > > > source touchpad controller that shares the same address as the original,
> > > > but is incompatible.
> > > >
> > > > The extra SKU IDs for the Tentacruel devices map to different sensor
> > > > components attached to the Embedded Controller. These are not visible
> > > > to the main processor.
> > > >
> > > > Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> > > > Acked-by: Conor Dooley <conor.dooley@microchip.com>
> > > > ---
> > > > Changes since v2:
> > > > - Picked up Conor's ack
> > > > - Rename touchpad to trackpad
> > > > - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> > > > source trackpad
> > > >
> > > > Changes since v1:
> > > > - Reorder SKU numbers in descending order.
> > > > - Fixed pinconfig node names
> > > > - Moved pinctrl-* properties after interrupts-*
> > > > - Switched to interrupts-extended for external components
> > > > - Marked ADSP as explicitly disabled, with a comment explaining that it
> > > > stalls the system
> > > > - Renamed "touchpad" to "trackpad"
> > > > - Dropped bogus "no-laneswap" property from it6505 node
> > > > - Moved "realtek,jd-src" property to after all the regulator supplies
> > > > - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> > > > - Renamed "vgpu" regulator name to allow coupling, with a comment
> > > > containing the name used in the design
> > > > - Renamed "cr50" node name to "tpm"
> > > > - Moved trackpad_pins reference up to i2c2; workaround for second source
> > > > component resource sharing.
> > > > - Fix copyright year
> > > > - Fixed touchscreen supply name
> > > >
> > > > arch/arm64/boot/dts/mediatek/Makefile | 4 +
> > > > .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> > > > .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> > > > .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> > > > .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> > > > .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> > > > .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
> > > > 7 files changed, 2003 insertions(+)
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > > > create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > > >
> > > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > > > index e6e7592a3645..442af61b1305 100644
> > > > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > > > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > > > @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> > > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
> > > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
> > > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
> > > > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
> > > > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > > > new file mode 100644
> > > > index 000000000000..9b2b64525961
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> > > > @@ -0,0 +1,129 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright 2022 Google LLC
> > > > + */
> > > > +
> > > > +/dts-v1/;
> > > > +#include "mt8186-corsola.dtsi"
> > > > +#include <dt-bindings/gpio/gpio.h>
> > > > +
> > > > +/ {
> > > > + aliases {
> > > > + i2c4 = &i2c4;
> > > > + };
> > > > +};
> > > > +
> > > > +&dsi_out {
> > > > + remote-endpoint = <&ps8640_in>;
> > > > +};
> > > > +
> > > > +&i2c0 {
> > > > + clock-frequency = <400000>;
> > > > +
> > > > + ps8640: edp-bridge@8 {
> > > > + compatible = "parade,ps8640";
> > > > + reg = <0x8>;
> > > > + powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
> > > > + reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&ps8640_pins>;
> > > > + vdd12-supply = <&mt6366_vrf12_reg>;
> > > > + vdd33-supply = <&mt6366_vcn33_reg>;
> > > > +
> > > > + ports {
> > > > + #address-cells = <1>;
> > > > + #size-cells = <0>;
> > > > +
> > > > + port@0 {
> > > > + reg = <0>;
> > > > +
> > > > + ps8640_in: endpoint {
> > > > + remote-endpoint = <&dsi_out>;
> > > > + };
> > > > + };
> > > > +
> > > > + port@1 {
> > > > + reg = <1>;
> > > > +
> > > > + ps8640_out: endpoint {
> > > > + remote-endpoint = <&panel_in>;
> > > > + };
> > > > + };
> > > > + };
> > > > +
> > > > + aux-bus {
> > > > + panel {
> > > > + compatible = "edp-panel";
> > > > + power-supply = <&pp3300_disp_x>;
> > > > + backlight = <&backlight_lcd0>;
> > > > +
> > > > + port {
> > > > + panel_in: endpoint {
> > > > + remote-endpoint = <&ps8640_out>;
> > > > + };
> > > > + };
> > > > + };
> > > > + };
> > > > + };
> > > > +};
> > > > +
> > > > +&i2c1 {
> > > > + i2c-scl-internal-delay-ns = <10000>;
> > > > +
> > > > + touchscreen: touchscreen@10 {
> > > > + compatible = "hid-over-i2c";
> > > > + reg = <0x10>;
> > > > + interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&touchscreen_pins>;
> > > > + post-power-on-delay-ms = <10>;
> > > > + hid-descr-addr = <0x0001>;
> > > > + vdd-supply = <&pp3300_s3>;
> > > > + };
> > > > +};
> > > > +
> > > > +&i2c4 {
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&i2c4_pins>;
> > > > + clock-frequency = <400000>;
> > > > + status = "okay";
> > > > +
> > > > + proximity@28 {
> > > > + compatible = "semtech,sx9324";
> > > > + reg = <0x28>;
> > > > + interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&sar_sensor_pins>;
> > > > + vdd-supply = <&mt6366_vio18_reg>;
> > > > + svdd-supply = <&mt6366_vio18_reg>;
> > > > + #io-channel-cells = <1>;
> > >
> > > From the newest DTS coding style document:
> > >
> > > The following order of properties in device nodes is preferred:
> > >
> > > 1. compatible
> > > 2. reg
> > > 3. ranges
> > > 4. Standard/common properties (defined by common bindings, e.g. without
> > > vendor-prefixes)
> > > 5. Vendor-specific properties
> > > 6. status (if applicable)
> > > 7. Child nodes, where each node is preceded with a blank line
> > >
> > > The "status" property is by default "okay", thus it can be omitted.
> > >
> > > The above-described ordering follows this approach:
> > >
> > > 1. Most important properties start the node: compatible then bus addressing to
> > > match unit address.
> > > 2. Each node will have common properties in similar place.
> > > 3. Status is the last information to annotate that device node is or is not
> > > finished (board resources are needed).
> >
> > Wishing for a checking tool now. :p
> >
> > > #io-channel-cells goes after `reg` (same for the other instances) :-)
> >
> > Ack (though it looks weird).
> >
> > > > + };
> > > > +};
> > > > +
> > > > +&pio {
> > > > + i2c4_pins: i2c4-pins {
> > > > + pins-bus {
> > > > + pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
> > > > + <PINMUX_GPIO135__FUNC_SCL4>;
> > > > + bias-disable;
> > > > + drive-strength = <4>;
> > > > + input-enable;
> > > > + };
> > > > + };
> > > > +
> > > > + ps8640_pins: ps8640-pins {
> > > > + pins-pwrdn-rst {
> > > > + pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
> > > > + <PINMUX_GPIO98__FUNC_GPIO98>;
> > > > + output-low;
> > > > + };
> > > > + };
> > > > +
> > > > + sar_sensor_pins: sar-sensor-pins {
> > > > + pins-irq {
> > > > + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
> > > > + input-enable;
> > > > + bias-pull-up;
> > > > + };
> > > > + };
> > > > +};
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > > > new file mode 100644
> > > > index 000000000000..9bb64353ca65
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> > > > @@ -0,0 +1,57 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright 2022 Google LLC
> > > > + */
> > > > +
> > > > +/dts-v1/;
> > > > +#include "mt8186-corsola-krabby.dtsi"
> > > > +
> > > > +/ {
> > > > + model = "Google Tentacool board";
> > > > + compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
> > > > + chassis-type = "laptop";
> > > > +};
> > > > +
> > > > +/* Tentacool omits the pen. */
> > > > +&gpio_keys {
> > > > + status = "disabled";
> > > > +};
> > > > +
> > > > +/* Tentacool omits the touchscreen; nothing else is on i2c1. */
> > > > +&i2c1 {
> > > > + status = "disabled";
> > > > +};
> > > > +
> > > > +&keyboard_controller {
> > > > + function-row-physmap = <
> > > > + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> > > > + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> > > > + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> > > > + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> > > > + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> > > > + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> > > > + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> > > > + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> > > > + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> > > > + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> > > > + >;
> > > > +
> > > > + linux,keymap = <
> > > > + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> > > > + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> > > > + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> > > > + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> > > > + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> > > > + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> > > > + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> > > > + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> > > > + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> > > > + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> > > > + CROS_STD_MAIN_KEYMAP
> > > > + >;
> > > > +};
> > > > +
> > > > +/* Tentacool omits the touchscreen. */
> > > > +&touchscreen {
> > > > + status = "disabled";
> > > > +};
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > > > new file mode 100644
> > > > index 000000000000..c3ae6f9616c8
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> > > > @@ -0,0 +1,24 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright 2023 Google LLC
> > > > + */
> > > > +
> > > > +#include "mt8186-corsola-tentacool-sku327681.dts"
> > > > +
> > > > +/ {
> > > > + compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
> > > > +};
> > > > +
> > > > +/* This variant replaces only the trackpad controller. */
> > > > +&i2c2 {
> > > > + /delete-node/ trackpad@15;
> > >
> > > Why are you deleting the trackpad@15 node?
> > >
> > > You can simply override the compatible, or actually omit the compatible string
> > > in the *.dtsi file, and set just that in each board *.dts.
> > >
> > > dtsi:
> > > trackpad_a: trackpad@15 {
> > > /* Compatible is set in each board dts */
> > > reg, interrupts, others
> > > }
> > >
> > > dts:
> > >
> > > &trackpad_a {
> > > compatible = "elan,ekth3000";
> > > };
> >
> > The original trackpad@15 comes from the base design and is used for all
> > models other than the ones with the conflicting component. Hence I believe
> > it should live in the base .dtsi.
> >
> > The delete-node makes it much less likely to have any lingering properties.
> > These are not nodes that just differ in compatible strings like DSI panels.
> > They have incompatible bindings. For example, elan,ekth3000 uses "vcc-supply",
> > while "hid-over-i2c" uses "vdd-supply".
> >
> > And going back to my previous argument, the base design used one specific
> > model which is carried over to all the other models.
> >
> > Suppose I add a phandle to the original trackpad, and do
> >
> > /delete-node/ &trackpad;
> >
> > Would that be better?
> >
> > > other dts:
> > >
> > > &trackpad_a {
> > > compatible = "hid-over-i2c";
> > > };
> > >
> > > > +
> > > > + trackpad@15 {
> > > > + compatible = "hid-over-i2c";
> > > > + reg = <0x15>;
> > > > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > > > + hid-descr-addr = <0x0001>;
> > > > + vdd-supply = <&pp3300_s3>;
> > > > + wakeup-source;
> > > > + };
> > > > +};
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > > > new file mode 100644
> > > > index 000000000000..26d3451a5e47
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> > > > @@ -0,0 +1,44 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright 2022 Google LLC
> > > > + */
> > > > +
> > > > +/dts-v1/;
> > > > +#include "mt8186-corsola-krabby.dtsi"
> > > > +
> > > > +/ {
> > > > + model = "Google Tentacruel board";
> > > > + compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
> > > > + "google,tentacruel-sku262145", "google,tentacruel-sku262144",
> > > > + "google,tentacruel", "mediatek,mt8186";
> > > > + chassis-type = "convertible";
> > > > +};
> > > > +
> > > > +&keyboard_controller {
> > > > + function-row-physmap = <
> > > > + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> > > > + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> > > > + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> > > > + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> > > > + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> > > > + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> > > > + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> > > > + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> > > > + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> > > > + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> > > > + >;
> > > > +
> > > > + linux,keymap = <
> > > > + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> > > > + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> > > > + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> > > > + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> > > > + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> > > > + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> > > > + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> > > > + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> > > > + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> > > > + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> > > > + CROS_STD_MAIN_KEYMAP
> > > > + >;
> > > > +};
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > > > new file mode 100644
> > > > index 000000000000..447b57b12b41
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> > > > @@ -0,0 +1,26 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright 2023 Google LLC
> > > > + */
> > > > +
> > > > +#include "mt8186-corsola-tentacruel-sku262144.dts"
> > > > +
> > > > +/ {
> > > > + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
> > > > + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
> > > > + "google,tentacruel", "mediatek,mt8186";
> > > > +};
> > > > +
> > > > +/* This variant replaces only the trackpad controller. */
> > > > +&i2c2 {
> > > > + /delete-node/ trackpad@15;
> > > > +
> > > > + trackpad@15 {
> > > > + compatible = "hid-over-i2c";
> > > > + reg = <0x15>;
> > > > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > > > + hid-descr-addr = <0x0001>;
> > > > + vdd-supply = <&pp3300_s3>;
> > > > + wakeup-source;
> > > > + };
> > > > +};
> > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > > > new file mode 100644
> > > > index 000000000000..8726b2916ef1
> > > > --- /dev/null
> > > > +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> > > > @@ -0,0 +1,1719 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/*
> > > > + * Copyright (C) 2022 MediaTek Inc.
> > > > + */
> > > > +/dts-v1/;
> > > > +#include "mt8186.dtsi"
> > > > +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> > > > +#include <dt-bindings/gpio/gpio.h>
> > > > +#include <dt-bindings/input/input.h>
> > > > +#include <dt-bindings/input/gpio-keys.h>
> > > > +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
> > > > +
> > > > +/ {
> > > > + aliases {
> > > > + i2c0 = &i2c0;
> > > > + i2c1 = &i2c1;
> > > > + i2c2 = &i2c2;
> > > > + i2c3 = &i2c3;
> > > > + i2c5 = &i2c5;
> > > > + mmc0 = &mmc0;
> > > > + mmc1 = &mmc1;
> > > > + serial0 = &uart0;
> > > > + };
> > > > +
> > > > + chosen {
> > > > + stdout-path = "serial0:115200n8";
> > > > + };
> > > > +
> > > > + memory@40000000 {
> > > > + device_type = "memory";
> > > > + /* The size should be filled in by the bootloader. */
> > > > + reg = <0 0x40000000 0 0>;
> > > > + };
> > > > +
> > > > + backlight_lcd0: backlight-lcd0 {
> > > > + compatible = "pwm-backlight";
> > > > + pwms = <&pwm0 0 500000>;
> > > > + power-supply = <&ppvar_sys>;
> > > > + enable-gpios = <&pio 152 0>;
> > > > + brightness-levels = <0 1023>;
> > > > + num-interpolated-steps = <1023>;
> > > > + default-brightness-level = <576>;
> > > > + };
> > > > +
> > > > + btsco: bt-sco {
> > >
> > > Do you really need the phandle to bt-sco?
> >
> > No. But the sound node probably should be referencing it and the dmic
> > node via DT instead of hardcoding the DAI and codec names in the machine
> > driver.
> >
> > Anyway, will remove the label for now.
> >
> > > Also, this node describes a codec, so: "bt-sco-codec" please!
> >
> > Ack.
> >
> > > > + compatible = "linux,bt-sco";
> > > > + #sound-dai-cells = <0>;
> > > > + };
> > > > +
> > > > + dmic_codec: dmic-codec {
> > >
> > > This phandle is unused...
> >
> > Removed.
> >
> > > ..snip..
> > >
> > > > +
> > > > +&adsp {
> > > > + memory-region = <&adsp_dma_mem>, <&adsp_mem>;
> > > > + status = "disabled"; /* causes stall */
> > >
> > > This is a firmware issue: once the correct firmware is uploaded to linux-firmware
> > > the dsp node can get enabled... so it we make sure that this happens before this
> > > devicetree gets picked, we can avoid a second commit enabling audio.
> > >
> > > After all, since we *want to* use the Xtensa DSP for audio, without it booted
> > > sound won't work *anyway*.... so having the firmware in place can also be seen
> > > as a direct dependency of the entire audio functionality.
> > >
> > > P.S.: The FW that is distributed with ChromeOS works just fine!
> >
> > I'll give that a try.
>
> I have:
>
> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
> sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
> sof-audio-of-mt8186 10680000.adsp: unknown sof_ext_man header type 3 size 0x30
> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
>
> and it's still hanging.
Looks like I was still using the bad version due to module options...
After removing the options, I now have:
sof-audio-of-mt8186 10680000.adsp: DT DSP detected
sof-audio-of-mt8186 10680000.adsp: assigned reserved memory node memory@61000000
sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-714c6
sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
sof-audio-of-mt8186 10680000.adsp: unknown sof_ext_man header type 3 size 0x30
sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-714c6
sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
But sound is still deferring probe:
# cat /sys/kernel/debug/devices_deferred
sound mt8186_mt6366_rt1019_rt5682s:
mt8186_mt6366_rt1019_rt5682s_dev_probe snd_soc_register_card fail
ChenYu
> And FTR, I think sound is also blocked on the it6505 audio support series.
>
> ChenYu
>
>
>
> > > > +};
> > > > +
> > > > +&afe {
> > > > + i2s0-share = "I2S1";
> > > > + i2s3-share = "I2S2";
> > > > + status = "okay";
> > > > +};
> > > > +
> > >
> > > ..snip..
> > >
> > > > +&i2c2 {
> > > > + pinctrl-names = "default";
> > > > + /*
> > > > + * Trackpad pin put here to work around second source components
> > > > + * sharing the pinmux in steelix designs.
> > > > + */
> > > > + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
> > >
> > > There's no choice for now... even if this is not beautiful to see... but it's still
> > > ok for me because we can revisit this later when the HW Prober mechanism will be
> > > upstreamed.
> >
> > Yup. Working on that.
> >
> > > > + clock-frequency = <400000>;
> > > > + i2c-scl-internal-delay-ns = <10000>;
> > > > + status = "okay";
> > > > +
> > > > + trackpad@15 {
> > > > + compatible = "elan,ekth3000";
> > > > + reg = <0x15>;
> > > > + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> > > > + vcc-supply = <&pp3300_s3>;
> > > > + wakeup-source;
> > > > + };
> > > > +};
> > > > +
> > >
> > > Thanks,
> > > Angelo
> >
> > Thanks for the review again.
> >
> > ChenYu
Il 07/12/23 12:28, Chen-Yu Tsai ha scritto:
> On Thu, Dec 7, 2023 at 8:23 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
>>
>> On Thu, Dec 7, 2023 at 2:28 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
>>>
>>> On Mon, Dec 4, 2023 at 11:27 PM AngeloGioacchino Del Regno
>>> <angelogioacchino.delregno@collabora.com> wrote:
>>>>
>>>> Il 04/12/23 09:40, Chen-Yu Tsai ha scritto:
>>>>> Tentacruel and Tentacool are MT8186 based Chromebooks based on the
>>>>> Krabby design.
>>>>>
>>>>> Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
>>>>> convertible device with touchscreen and stylus.
>>>>>
>>>>> Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
>>>>> device. It does not have a touchscreen or stylus.
>>>>>
>>>>> The two devices both have two variants. The difference is a second
>>>>> source touchpad controller that shares the same address as the original,
>>>>> but is incompatible.
>>>>>
>>>>> The extra SKU IDs for the Tentacruel devices map to different sensor
>>>>> components attached to the Embedded Controller. These are not visible
>>>>> to the main processor.
>>>>>
>>>>> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
>>>>> Acked-by: Conor Dooley <conor.dooley@microchip.com>
>>>>> ---
>>>>> Changes since v2:
>>>>> - Picked up Conor's ack
>>>>> - Rename touchpad to trackpad
>>>>> - Drop pinctrl properties from trackpad in tentacruel/tentacool second
>>>>> source trackpad
>>>>>
>>>>> Changes since v1:
>>>>> - Reorder SKU numbers in descending order.
>>>>> - Fixed pinconfig node names
>>>>> - Moved pinctrl-* properties after interrupts-*
>>>>> - Switched to interrupts-extended for external components
>>>>> - Marked ADSP as explicitly disabled, with a comment explaining that it
>>>>> stalls the system
>>>>> - Renamed "touchpad" to "trackpad"
>>>>> - Dropped bogus "no-laneswap" property from it6505 node
>>>>> - Moved "realtek,jd-src" property to after all the regulator supplies
>>>>> - Switched to macros for MT6366 regulator "regulator-allowed-modes"
>>>>> - Renamed "vgpu" regulator name to allow coupling, with a comment
>>>>> containing the name used in the design
>>>>> - Renamed "cr50" node name to "tpm"
>>>>> - Moved trackpad_pins reference up to i2c2; workaround for second source
>>>>> component resource sharing.
>>>>> - Fix copyright year
>>>>> - Fixed touchscreen supply name
>>>>>
>>>>> arch/arm64/boot/dts/mediatek/Makefile | 4 +
>>>>> .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
>>>>> .../mt8186-corsola-tentacool-sku327681.dts | 57 +
>>>>> .../mt8186-corsola-tentacool-sku327683.dts | 24 +
>>>>> .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
>>>>> .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
>>>>> .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
>>>>> 7 files changed, 2003 insertions(+)
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
>>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
>>>>>
>>>>> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
>>>>> index e6e7592a3645..442af61b1305 100644
>>>>> --- a/arch/arm64/boot/dts/mediatek/Makefile
>>>>> +++ b/arch/arm64/boot/dts/mediatek/Makefile
>>>>> @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
>>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
>>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
>>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
>>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
>>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
>>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
>>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
>>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
>>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
>>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
>>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
>>>>> new file mode 100644
>>>>> index 000000000000..9b2b64525961
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
>>>>> @@ -0,0 +1,129 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>>>> +/*
>>>>> + * Copyright 2022 Google LLC
>>>>> + */
>>>>> +
>>>>> +/dts-v1/;
>>>>> +#include "mt8186-corsola.dtsi"
>>>>> +#include <dt-bindings/gpio/gpio.h>
>>>>> +
>>>>> +/ {
>>>>> + aliases {
>>>>> + i2c4 = &i2c4;
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&dsi_out {
>>>>> + remote-endpoint = <&ps8640_in>;
>>>>> +};
>>>>> +
>>>>> +&i2c0 {
>>>>> + clock-frequency = <400000>;
>>>>> +
>>>>> + ps8640: edp-bridge@8 {
>>>>> + compatible = "parade,ps8640";
>>>>> + reg = <0x8>;
>>>>> + powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
>>>>> + reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&ps8640_pins>;
>>>>> + vdd12-supply = <&mt6366_vrf12_reg>;
>>>>> + vdd33-supply = <&mt6366_vcn33_reg>;
>>>>> +
>>>>> + ports {
>>>>> + #address-cells = <1>;
>>>>> + #size-cells = <0>;
>>>>> +
>>>>> + port@0 {
>>>>> + reg = <0>;
>>>>> +
>>>>> + ps8640_in: endpoint {
>>>>> + remote-endpoint = <&dsi_out>;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + port@1 {
>>>>> + reg = <1>;
>>>>> +
>>>>> + ps8640_out: endpoint {
>>>>> + remote-endpoint = <&panel_in>;
>>>>> + };
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + aux-bus {
>>>>> + panel {
>>>>> + compatible = "edp-panel";
>>>>> + power-supply = <&pp3300_disp_x>;
>>>>> + backlight = <&backlight_lcd0>;
>>>>> +
>>>>> + port {
>>>>> + panel_in: endpoint {
>>>>> + remote-endpoint = <&ps8640_out>;
>>>>> + };
>>>>> + };
>>>>> + };
>>>>> + };
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&i2c1 {
>>>>> + i2c-scl-internal-delay-ns = <10000>;
>>>>> +
>>>>> + touchscreen: touchscreen@10 {
>>>>> + compatible = "hid-over-i2c";
>>>>> + reg = <0x10>;
>>>>> + interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&touchscreen_pins>;
>>>>> + post-power-on-delay-ms = <10>;
>>>>> + hid-descr-addr = <0x0001>;
>>>>> + vdd-supply = <&pp3300_s3>;
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&i2c4 {
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&i2c4_pins>;
>>>>> + clock-frequency = <400000>;
>>>>> + status = "okay";
>>>>> +
>>>>> + proximity@28 {
>>>>> + compatible = "semtech,sx9324";
>>>>> + reg = <0x28>;
>>>>> + interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&sar_sensor_pins>;
>>>>> + vdd-supply = <&mt6366_vio18_reg>;
>>>>> + svdd-supply = <&mt6366_vio18_reg>;
>>>>> + #io-channel-cells = <1>;
>>>>
>>>> From the newest DTS coding style document:
>>>>
>>>> The following order of properties in device nodes is preferred:
>>>>
>>>> 1. compatible
>>>> 2. reg
>>>> 3. ranges
>>>> 4. Standard/common properties (defined by common bindings, e.g. without
>>>> vendor-prefixes)
>>>> 5. Vendor-specific properties
>>>> 6. status (if applicable)
>>>> 7. Child nodes, where each node is preceded with a blank line
>>>>
>>>> The "status" property is by default "okay", thus it can be omitted.
>>>>
>>>> The above-described ordering follows this approach:
>>>>
>>>> 1. Most important properties start the node: compatible then bus addressing to
>>>> match unit address.
>>>> 2. Each node will have common properties in similar place.
>>>> 3. Status is the last information to annotate that device node is or is not
>>>> finished (board resources are needed).
>>>
>>> Wishing for a checking tool now. :p
>>>
>>>> #io-channel-cells goes after `reg` (same for the other instances) :-)
>>>
>>> Ack (though it looks weird).
>>>
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&pio {
>>>>> + i2c4_pins: i2c4-pins {
>>>>> + pins-bus {
>>>>> + pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
>>>>> + <PINMUX_GPIO135__FUNC_SCL4>;
>>>>> + bias-disable;
>>>>> + drive-strength = <4>;
>>>>> + input-enable;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + ps8640_pins: ps8640-pins {
>>>>> + pins-pwrdn-rst {
>>>>> + pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
>>>>> + <PINMUX_GPIO98__FUNC_GPIO98>;
>>>>> + output-low;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + sar_sensor_pins: sar-sensor-pins {
>>>>> + pins-irq {
>>>>> + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
>>>>> + input-enable;
>>>>> + bias-pull-up;
>>>>> + };
>>>>> + };
>>>>> +};
>>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
>>>>> new file mode 100644
>>>>> index 000000000000..9bb64353ca65
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
>>>>> @@ -0,0 +1,57 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>>>> +/*
>>>>> + * Copyright 2022 Google LLC
>>>>> + */
>>>>> +
>>>>> +/dts-v1/;
>>>>> +#include "mt8186-corsola-krabby.dtsi"
>>>>> +
>>>>> +/ {
>>>>> + model = "Google Tentacool board";
>>>>> + compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
>>>>> + chassis-type = "laptop";
>>>>> +};
>>>>> +
>>>>> +/* Tentacool omits the pen. */
>>>>> +&gpio_keys {
>>>>> + status = "disabled";
>>>>> +};
>>>>> +
>>>>> +/* Tentacool omits the touchscreen; nothing else is on i2c1. */
>>>>> +&i2c1 {
>>>>> + status = "disabled";
>>>>> +};
>>>>> +
>>>>> +&keyboard_controller {
>>>>> + function-row-physmap = <
>>>>> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
>>>>> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
>>>>> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
>>>>> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
>>>>> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
>>>>> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
>>>>> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
>>>>> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
>>>>> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
>>>>> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
>>>>> + >;
>>>>> +
>>>>> + linux,keymap = <
>>>>> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
>>>>> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
>>>>> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
>>>>> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
>>>>> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
>>>>> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
>>>>> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
>>>>> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
>>>>> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
>>>>> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
>>>>> + CROS_STD_MAIN_KEYMAP
>>>>> + >;
>>>>> +};
>>>>> +
>>>>> +/* Tentacool omits the touchscreen. */
>>>>> +&touchscreen {
>>>>> + status = "disabled";
>>>>> +};
>>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
>>>>> new file mode 100644
>>>>> index 000000000000..c3ae6f9616c8
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
>>>>> @@ -0,0 +1,24 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>>>> +/*
>>>>> + * Copyright 2023 Google LLC
>>>>> + */
>>>>> +
>>>>> +#include "mt8186-corsola-tentacool-sku327681.dts"
>>>>> +
>>>>> +/ {
>>>>> + compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
>>>>> +};
>>>>> +
>>>>> +/* This variant replaces only the trackpad controller. */
>>>>> +&i2c2 {
>>>>> + /delete-node/ trackpad@15;
>>>>
>>>> Why are you deleting the trackpad@15 node?
>>>>
>>>> You can simply override the compatible, or actually omit the compatible string
>>>> in the *.dtsi file, and set just that in each board *.dts.
>>>>
>>>> dtsi:
>>>> trackpad_a: trackpad@15 {
>>>> /* Compatible is set in each board dts */
>>>> reg, interrupts, others
>>>> }
>>>>
>>>> dts:
>>>>
>>>> &trackpad_a {
>>>> compatible = "elan,ekth3000";
>>>> };
>>>
>>> The original trackpad@15 comes from the base design and is used for all
>>> models other than the ones with the conflicting component. Hence I believe
>>> it should live in the base .dtsi.
>>>
>>> The delete-node makes it much less likely to have any lingering properties.
>>> These are not nodes that just differ in compatible strings like DSI panels.
>>> They have incompatible bindings. For example, elan,ekth3000 uses "vcc-supply",
>>> while "hid-over-i2c" uses "vdd-supply".
>>>
>>> And going back to my previous argument, the base design used one specific
>>> model which is carried over to all the other models.
>>>
>>> Suppose I add a phandle to the original trackpad, and do
>>>
>>> /delete-node/ &trackpad;
>>>
>>> Would that be better?
>>>
>>>> other dts:
>>>>
>>>> &trackpad_a {
>>>> compatible = "hid-over-i2c";
>>>> };
>>>>
>>>>> +
>>>>> + trackpad@15 {
>>>>> + compatible = "hid-over-i2c";
>>>>> + reg = <0x15>;
>>>>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
>>>>> + hid-descr-addr = <0x0001>;
>>>>> + vdd-supply = <&pp3300_s3>;
>>>>> + wakeup-source;
>>>>> + };
>>>>> +};
>>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
>>>>> new file mode 100644
>>>>> index 000000000000..26d3451a5e47
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
>>>>> @@ -0,0 +1,44 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>>>> +/*
>>>>> + * Copyright 2022 Google LLC
>>>>> + */
>>>>> +
>>>>> +/dts-v1/;
>>>>> +#include "mt8186-corsola-krabby.dtsi"
>>>>> +
>>>>> +/ {
>>>>> + model = "Google Tentacruel board";
>>>>> + compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
>>>>> + "google,tentacruel-sku262145", "google,tentacruel-sku262144",
>>>>> + "google,tentacruel", "mediatek,mt8186";
>>>>> + chassis-type = "convertible";
>>>>> +};
>>>>> +
>>>>> +&keyboard_controller {
>>>>> + function-row-physmap = <
>>>>> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
>>>>> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
>>>>> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
>>>>> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
>>>>> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
>>>>> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
>>>>> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
>>>>> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
>>>>> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
>>>>> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
>>>>> + >;
>>>>> +
>>>>> + linux,keymap = <
>>>>> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
>>>>> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
>>>>> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
>>>>> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
>>>>> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
>>>>> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
>>>>> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
>>>>> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
>>>>> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
>>>>> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
>>>>> + CROS_STD_MAIN_KEYMAP
>>>>> + >;
>>>>> +};
>>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
>>>>> new file mode 100644
>>>>> index 000000000000..447b57b12b41
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
>>>>> @@ -0,0 +1,26 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>>>> +/*
>>>>> + * Copyright 2023 Google LLC
>>>>> + */
>>>>> +
>>>>> +#include "mt8186-corsola-tentacruel-sku262144.dts"
>>>>> +
>>>>> +/ {
>>>>> + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
>>>>> + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
>>>>> + "google,tentacruel", "mediatek,mt8186";
>>>>> +};
>>>>> +
>>>>> +/* This variant replaces only the trackpad controller. */
>>>>> +&i2c2 {
>>>>> + /delete-node/ trackpad@15;
>>>>> +
>>>>> + trackpad@15 {
>>>>> + compatible = "hid-over-i2c";
>>>>> + reg = <0x15>;
>>>>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
>>>>> + hid-descr-addr = <0x0001>;
>>>>> + vdd-supply = <&pp3300_s3>;
>>>>> + wakeup-source;
>>>>> + };
>>>>> +};
>>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
>>>>> new file mode 100644
>>>>> index 000000000000..8726b2916ef1
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
>>>>> @@ -0,0 +1,1719 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
>>>>> +/*
>>>>> + * Copyright (C) 2022 MediaTek Inc.
>>>>> + */
>>>>> +/dts-v1/;
>>>>> +#include "mt8186.dtsi"
>>>>> +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
>>>>> +#include <dt-bindings/gpio/gpio.h>
>>>>> +#include <dt-bindings/input/input.h>
>>>>> +#include <dt-bindings/input/gpio-keys.h>
>>>>> +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
>>>>> +
>>>>> +/ {
>>>>> + aliases {
>>>>> + i2c0 = &i2c0;
>>>>> + i2c1 = &i2c1;
>>>>> + i2c2 = &i2c2;
>>>>> + i2c3 = &i2c3;
>>>>> + i2c5 = &i2c5;
>>>>> + mmc0 = &mmc0;
>>>>> + mmc1 = &mmc1;
>>>>> + serial0 = &uart0;
>>>>> + };
>>>>> +
>>>>> + chosen {
>>>>> + stdout-path = "serial0:115200n8";
>>>>> + };
>>>>> +
>>>>> + memory@40000000 {
>>>>> + device_type = "memory";
>>>>> + /* The size should be filled in by the bootloader. */
>>>>> + reg = <0 0x40000000 0 0>;
>>>>> + };
>>>>> +
>>>>> + backlight_lcd0: backlight-lcd0 {
>>>>> + compatible = "pwm-backlight";
>>>>> + pwms = <&pwm0 0 500000>;
>>>>> + power-supply = <&ppvar_sys>;
>>>>> + enable-gpios = <&pio 152 0>;
>>>>> + brightness-levels = <0 1023>;
>>>>> + num-interpolated-steps = <1023>;
>>>>> + default-brightness-level = <576>;
>>>>> + };
>>>>> +
>>>>> + btsco: bt-sco {
>>>>
>>>> Do you really need the phandle to bt-sco?
>>>
>>> No. But the sound node probably should be referencing it and the dmic
>>> node via DT instead of hardcoding the DAI and codec names in the machine
>>> driver.
>>>
>>> Anyway, will remove the label for now.
>>>
>>>> Also, this node describes a codec, so: "bt-sco-codec" please!
>>>
>>> Ack.
>>>
>>>>> + compatible = "linux,bt-sco";
>>>>> + #sound-dai-cells = <0>;
>>>>> + };
>>>>> +
>>>>> + dmic_codec: dmic-codec {
>>>>
>>>> This phandle is unused...
>>>
>>> Removed.
>>>
>>>> ..snip..
>>>>
>>>>> +
>>>>> +&adsp {
>>>>> + memory-region = <&adsp_dma_mem>, <&adsp_mem>;
>>>>> + status = "disabled"; /* causes stall */
>>>>
>>>> This is a firmware issue: once the correct firmware is uploaded to linux-firmware
>>>> the dsp node can get enabled... so it we make sure that this happens before this
>>>> devicetree gets picked, we can avoid a second commit enabling audio.
>>>>
>>>> After all, since we *want to* use the Xtensa DSP for audio, without it booted
>>>> sound won't work *anyway*.... so having the firmware in place can also be seen
>>>> as a direct dependency of the entire audio functionality.
>>>>
>>>> P.S.: The FW that is distributed with ChromeOS works just fine!
>>>
>>> I'll give that a try.
>>
>> I have:
>>
>> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
>> sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
>> sof-audio-of-mt8186 10680000.adsp: unknown sof_ext_man header type 3 size 0x30
>> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
>>
>> and it's still hanging.
>
> Looks like I was still using the bad version due to module options...
>
> After removing the options, I now have:
>
> sof-audio-of-mt8186 10680000.adsp: DT DSP detected
> sof-audio-of-mt8186 10680000.adsp: assigned reserved memory node memory@61000000
> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-714c6
> sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
> sof-audio-of-mt8186 10680000.adsp: unknown sof_ext_man header type 3 size 0x30
> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-714c6
> sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
>
> But sound is still deferring probe:
>
> # cat /sys/kernel/debug/devices_deferred
> sound mt8186_mt6366_rt1019_rt5682s:
> mt8186_mt6366_rt1019_rt5682s_dev_probe snd_soc_register_card fail
>
Yes, this happens because of the missing IT6505 HDMI audio support - but it's not
giving any side effect anyway... in this case, as far as DT is concerned... there
will be no change, and no side effects on working parts of the system, so we can
(imo) upstream this even if the driver-code-only dependency is not there yet.
Cheers!
Angelo
> ChenYu
>
>> And FTR, I think sound is also blocked on the it6505 audio support series.
>>
>> ChenYu
>>
>>
>>
>>>>> +};
>>>>> +
>>>>> +&afe {
>>>>> + i2s0-share = "I2S1";
>>>>> + i2s3-share = "I2S2";
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>
>>>> ..snip..
>>>>
>>>>> +&i2c2 {
>>>>> + pinctrl-names = "default";
>>>>> + /*
>>>>> + * Trackpad pin put here to work around second source components
>>>>> + * sharing the pinmux in steelix designs.
>>>>> + */
>>>>> + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
>>>>
>>>> There's no choice for now... even if this is not beautiful to see... but it's still
>>>> ok for me because we can revisit this later when the HW Prober mechanism will be
>>>> upstreamed.
>>>
>>> Yup. Working on that.
>>>
>>>>> + clock-frequency = <400000>;
>>>>> + i2c-scl-internal-delay-ns = <10000>;
>>>>> + status = "okay";
>>>>> +
>>>>> + trackpad@15 {
>>>>> + compatible = "elan,ekth3000";
>>>>> + reg = <0x15>;
>>>>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
>>>>> + vcc-supply = <&pp3300_s3>;
>>>>> + wakeup-source;
>>>>> + };
>>>>> +};
>>>>> +
>>>>
>>>> Thanks,
>>>> Angelo
>>>
>>> Thanks for the review again.
>>>
>>> ChenYu
On Thu, Dec 7, 2023 at 10:00 PM AngeloGioacchino Del Regno
<angelogioacchino.delregno@collabora.com> wrote:
>
> Il 07/12/23 12:28, Chen-Yu Tsai ha scritto:
> > On Thu, Dec 7, 2023 at 8:23 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
> >>
> >> On Thu, Dec 7, 2023 at 2:28 PM Chen-Yu Tsai <wenst@chromium.org> wrote:
> >>>
> >>> On Mon, Dec 4, 2023 at 11:27 PM AngeloGioacchino Del Regno
> >>> <angelogioacchino.delregno@collabora.com> wrote:
> >>>>
> >>>> Il 04/12/23 09:40, Chen-Yu Tsai ha scritto:
> >>>>> Tentacruel and Tentacool are MT8186 based Chromebooks based on the
> >>>>> Krabby design.
> >>>>>
> >>>>> Tentacruel, also known as the ASUS Chromebook CM14 Flip CM1402F, is a
> >>>>> convertible device with touchscreen and stylus.
> >>>>>
> >>>>> Tentacool, also known as the ASUS Chromebook CM14 CM1402C, is a laptop
> >>>>> device. It does not have a touchscreen or stylus.
> >>>>>
> >>>>> The two devices both have two variants. The difference is a second
> >>>>> source touchpad controller that shares the same address as the original,
> >>>>> but is incompatible.
> >>>>>
> >>>>> The extra SKU IDs for the Tentacruel devices map to different sensor
> >>>>> components attached to the Embedded Controller. These are not visible
> >>>>> to the main processor.
> >>>>>
> >>>>> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
> >>>>> Acked-by: Conor Dooley <conor.dooley@microchip.com>
> >>>>> ---
> >>>>> Changes since v2:
> >>>>> - Picked up Conor's ack
> >>>>> - Rename touchpad to trackpad
> >>>>> - Drop pinctrl properties from trackpad in tentacruel/tentacool second
> >>>>> source trackpad
> >>>>>
> >>>>> Changes since v1:
> >>>>> - Reorder SKU numbers in descending order.
> >>>>> - Fixed pinconfig node names
> >>>>> - Moved pinctrl-* properties after interrupts-*
> >>>>> - Switched to interrupts-extended for external components
> >>>>> - Marked ADSP as explicitly disabled, with a comment explaining that it
> >>>>> stalls the system
> >>>>> - Renamed "touchpad" to "trackpad"
> >>>>> - Dropped bogus "no-laneswap" property from it6505 node
> >>>>> - Moved "realtek,jd-src" property to after all the regulator supplies
> >>>>> - Switched to macros for MT6366 regulator "regulator-allowed-modes"
> >>>>> - Renamed "vgpu" regulator name to allow coupling, with a comment
> >>>>> containing the name used in the design
> >>>>> - Renamed "cr50" node name to "tpm"
> >>>>> - Moved trackpad_pins reference up to i2c2; workaround for second source
> >>>>> component resource sharing.
> >>>>> - Fix copyright year
> >>>>> - Fixed touchscreen supply name
> >>>>>
> >>>>> arch/arm64/boot/dts/mediatek/Makefile | 4 +
> >>>>> .../dts/mediatek/mt8186-corsola-krabby.dtsi | 129 ++
> >>>>> .../mt8186-corsola-tentacool-sku327681.dts | 57 +
> >>>>> .../mt8186-corsola-tentacool-sku327683.dts | 24 +
> >>>>> .../mt8186-corsola-tentacruel-sku262144.dts | 44 +
> >>>>> .../mt8186-corsola-tentacruel-sku262148.dts | 26 +
> >>>>> .../boot/dts/mediatek/mt8186-corsola.dtsi | 1719 +++++++++++++++++
> >>>>> 7 files changed, 2003 insertions(+)
> >>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> >>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> >>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> >>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> >>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> >>>>> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> >>>>>
> >>>>> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> >>>>> index e6e7592a3645..442af61b1305 100644
> >>>>> --- a/arch/arm64/boot/dts/mediatek/Makefile
> >>>>> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> >>>>> @@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> >>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> >>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> >>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> >>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
> >>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
> >>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
> >>>>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
> >>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> >>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
> >>>>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
> >>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> >>>>> new file mode 100644
> >>>>> index 000000000000..9b2b64525961
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-krabby.dtsi
> >>>>> @@ -0,0 +1,129 @@
> >>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>>>> +/*
> >>>>> + * Copyright 2022 Google LLC
> >>>>> + */
> >>>>> +
> >>>>> +/dts-v1/;
> >>>>> +#include "mt8186-corsola.dtsi"
> >>>>> +#include <dt-bindings/gpio/gpio.h>
> >>>>> +
> >>>>> +/ {
> >>>>> + aliases {
> >>>>> + i2c4 = &i2c4;
> >>>>> + };
> >>>>> +};
> >>>>> +
> >>>>> +&dsi_out {
> >>>>> + remote-endpoint = <&ps8640_in>;
> >>>>> +};
> >>>>> +
> >>>>> +&i2c0 {
> >>>>> + clock-frequency = <400000>;
> >>>>> +
> >>>>> + ps8640: edp-bridge@8 {
> >>>>> + compatible = "parade,ps8640";
> >>>>> + reg = <0x8>;
> >>>>> + powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
> >>>>> + reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
> >>>>> + pinctrl-names = "default";
> >>>>> + pinctrl-0 = <&ps8640_pins>;
> >>>>> + vdd12-supply = <&mt6366_vrf12_reg>;
> >>>>> + vdd33-supply = <&mt6366_vcn33_reg>;
> >>>>> +
> >>>>> + ports {
> >>>>> + #address-cells = <1>;
> >>>>> + #size-cells = <0>;
> >>>>> +
> >>>>> + port@0 {
> >>>>> + reg = <0>;
> >>>>> +
> >>>>> + ps8640_in: endpoint {
> >>>>> + remote-endpoint = <&dsi_out>;
> >>>>> + };
> >>>>> + };
> >>>>> +
> >>>>> + port@1 {
> >>>>> + reg = <1>;
> >>>>> +
> >>>>> + ps8640_out: endpoint {
> >>>>> + remote-endpoint = <&panel_in>;
> >>>>> + };
> >>>>> + };
> >>>>> + };
> >>>>> +
> >>>>> + aux-bus {
> >>>>> + panel {
> >>>>> + compatible = "edp-panel";
> >>>>> + power-supply = <&pp3300_disp_x>;
> >>>>> + backlight = <&backlight_lcd0>;
> >>>>> +
> >>>>> + port {
> >>>>> + panel_in: endpoint {
> >>>>> + remote-endpoint = <&ps8640_out>;
> >>>>> + };
> >>>>> + };
> >>>>> + };
> >>>>> + };
> >>>>> + };
> >>>>> +};
> >>>>> +
> >>>>> +&i2c1 {
> >>>>> + i2c-scl-internal-delay-ns = <10000>;
> >>>>> +
> >>>>> + touchscreen: touchscreen@10 {
> >>>>> + compatible = "hid-over-i2c";
> >>>>> + reg = <0x10>;
> >>>>> + interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
> >>>>> + pinctrl-names = "default";
> >>>>> + pinctrl-0 = <&touchscreen_pins>;
> >>>>> + post-power-on-delay-ms = <10>;
> >>>>> + hid-descr-addr = <0x0001>;
> >>>>> + vdd-supply = <&pp3300_s3>;
> >>>>> + };
> >>>>> +};
> >>>>> +
> >>>>> +&i2c4 {
> >>>>> + pinctrl-names = "default";
> >>>>> + pinctrl-0 = <&i2c4_pins>;
> >>>>> + clock-frequency = <400000>;
> >>>>> + status = "okay";
> >>>>> +
> >>>>> + proximity@28 {
> >>>>> + compatible = "semtech,sx9324";
> >>>>> + reg = <0x28>;
> >>>>> + interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
> >>>>> + pinctrl-names = "default";
> >>>>> + pinctrl-0 = <&sar_sensor_pins>;
> >>>>> + vdd-supply = <&mt6366_vio18_reg>;
> >>>>> + svdd-supply = <&mt6366_vio18_reg>;
> >>>>> + #io-channel-cells = <1>;
> >>>>
> >>>> From the newest DTS coding style document:
> >>>>
> >>>> The following order of properties in device nodes is preferred:
> >>>>
> >>>> 1. compatible
> >>>> 2. reg
> >>>> 3. ranges
> >>>> 4. Standard/common properties (defined by common bindings, e.g. without
> >>>> vendor-prefixes)
> >>>> 5. Vendor-specific properties
> >>>> 6. status (if applicable)
> >>>> 7. Child nodes, where each node is preceded with a blank line
> >>>>
> >>>> The "status" property is by default "okay", thus it can be omitted.
> >>>>
> >>>> The above-described ordering follows this approach:
> >>>>
> >>>> 1. Most important properties start the node: compatible then bus addressing to
> >>>> match unit address.
> >>>> 2. Each node will have common properties in similar place.
> >>>> 3. Status is the last information to annotate that device node is or is not
> >>>> finished (board resources are needed).
> >>>
> >>> Wishing for a checking tool now. :p
> >>>
> >>>> #io-channel-cells goes after `reg` (same for the other instances) :-)
> >>>
> >>> Ack (though it looks weird).
> >>>
> >>>>> + };
> >>>>> +};
> >>>>> +
> >>>>> +&pio {
> >>>>> + i2c4_pins: i2c4-pins {
> >>>>> + pins-bus {
> >>>>> + pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
> >>>>> + <PINMUX_GPIO135__FUNC_SCL4>;
> >>>>> + bias-disable;
> >>>>> + drive-strength = <4>;
> >>>>> + input-enable;
> >>>>> + };
> >>>>> + };
> >>>>> +
> >>>>> + ps8640_pins: ps8640-pins {
> >>>>> + pins-pwrdn-rst {
> >>>>> + pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
> >>>>> + <PINMUX_GPIO98__FUNC_GPIO98>;
> >>>>> + output-low;
> >>>>> + };
> >>>>> + };
> >>>>> +
> >>>>> + sar_sensor_pins: sar-sensor-pins {
> >>>>> + pins-irq {
> >>>>> + pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
> >>>>> + input-enable;
> >>>>> + bias-pull-up;
> >>>>> + };
> >>>>> + };
> >>>>> +};
> >>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> >>>>> new file mode 100644
> >>>>> index 000000000000..9bb64353ca65
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327681.dts
> >>>>> @@ -0,0 +1,57 @@
> >>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>>>> +/*
> >>>>> + * Copyright 2022 Google LLC
> >>>>> + */
> >>>>> +
> >>>>> +/dts-v1/;
> >>>>> +#include "mt8186-corsola-krabby.dtsi"
> >>>>> +
> >>>>> +/ {
> >>>>> + model = "Google Tentacool board";
> >>>>> + compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
> >>>>> + chassis-type = "laptop";
> >>>>> +};
> >>>>> +
> >>>>> +/* Tentacool omits the pen. */
> >>>>> +&gpio_keys {
> >>>>> + status = "disabled";
> >>>>> +};
> >>>>> +
> >>>>> +/* Tentacool omits the touchscreen; nothing else is on i2c1. */
> >>>>> +&i2c1 {
> >>>>> + status = "disabled";
> >>>>> +};
> >>>>> +
> >>>>> +&keyboard_controller {
> >>>>> + function-row-physmap = <
> >>>>> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> >>>>> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> >>>>> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> >>>>> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> >>>>> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> >>>>> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> >>>>> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> >>>>> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> >>>>> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> >>>>> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> >>>>> + >;
> >>>>> +
> >>>>> + linux,keymap = <
> >>>>> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> >>>>> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> >>>>> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> >>>>> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> >>>>> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> >>>>> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> >>>>> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> >>>>> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> >>>>> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> >>>>> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> >>>>> + CROS_STD_MAIN_KEYMAP
> >>>>> + >;
> >>>>> +};
> >>>>> +
> >>>>> +/* Tentacool omits the touchscreen. */
> >>>>> +&touchscreen {
> >>>>> + status = "disabled";
> >>>>> +};
> >>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> >>>>> new file mode 100644
> >>>>> index 000000000000..c3ae6f9616c8
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacool-sku327683.dts
> >>>>> @@ -0,0 +1,24 @@
> >>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>>>> +/*
> >>>>> + * Copyright 2023 Google LLC
> >>>>> + */
> >>>>> +
> >>>>> +#include "mt8186-corsola-tentacool-sku327681.dts"
> >>>>> +
> >>>>> +/ {
> >>>>> + compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
> >>>>> +};
> >>>>> +
> >>>>> +/* This variant replaces only the trackpad controller. */
> >>>>> +&i2c2 {
> >>>>> + /delete-node/ trackpad@15;
> >>>>
> >>>> Why are you deleting the trackpad@15 node?
> >>>>
> >>>> You can simply override the compatible, or actually omit the compatible string
> >>>> in the *.dtsi file, and set just that in each board *.dts.
> >>>>
> >>>> dtsi:
> >>>> trackpad_a: trackpad@15 {
> >>>> /* Compatible is set in each board dts */
> >>>> reg, interrupts, others
> >>>> }
> >>>>
> >>>> dts:
> >>>>
> >>>> &trackpad_a {
> >>>> compatible = "elan,ekth3000";
> >>>> };
> >>>
> >>> The original trackpad@15 comes from the base design and is used for all
> >>> models other than the ones with the conflicting component. Hence I believe
> >>> it should live in the base .dtsi.
> >>>
> >>> The delete-node makes it much less likely to have any lingering properties.
> >>> These are not nodes that just differ in compatible strings like DSI panels.
> >>> They have incompatible bindings. For example, elan,ekth3000 uses "vcc-supply",
> >>> while "hid-over-i2c" uses "vdd-supply".
> >>>
> >>> And going back to my previous argument, the base design used one specific
> >>> model which is carried over to all the other models.
> >>>
> >>> Suppose I add a phandle to the original trackpad, and do
> >>>
> >>> /delete-node/ &trackpad;
> >>>
> >>> Would that be better?
> >>>
> >>>> other dts:
> >>>>
> >>>> &trackpad_a {
> >>>> compatible = "hid-over-i2c";
> >>>> };
> >>>>
> >>>>> +
> >>>>> + trackpad@15 {
> >>>>> + compatible = "hid-over-i2c";
> >>>>> + reg = <0x15>;
> >>>>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> >>>>> + hid-descr-addr = <0x0001>;
> >>>>> + vdd-supply = <&pp3300_s3>;
> >>>>> + wakeup-source;
> >>>>> + };
> >>>>> +};
> >>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> >>>>> new file mode 100644
> >>>>> index 000000000000..26d3451a5e47
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262144.dts
> >>>>> @@ -0,0 +1,44 @@
> >>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>>>> +/*
> >>>>> + * Copyright 2022 Google LLC
> >>>>> + */
> >>>>> +
> >>>>> +/dts-v1/;
> >>>>> +#include "mt8186-corsola-krabby.dtsi"
> >>>>> +
> >>>>> +/ {
> >>>>> + model = "Google Tentacruel board";
> >>>>> + compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
> >>>>> + "google,tentacruel-sku262145", "google,tentacruel-sku262144",
> >>>>> + "google,tentacruel", "mediatek,mt8186";
> >>>>> + chassis-type = "convertible";
> >>>>> +};
> >>>>> +
> >>>>> +&keyboard_controller {
> >>>>> + function-row-physmap = <
> >>>>> + MATRIX_KEY(0x00, 0x02, 0) /* T1 */
> >>>>> + MATRIX_KEY(0x03, 0x02, 0) /* T2 */
> >>>>> + MATRIX_KEY(0x02, 0x02, 0) /* T3 */
> >>>>> + MATRIX_KEY(0x01, 0x02, 0) /* T4 */
> >>>>> + MATRIX_KEY(0x03, 0x04, 0) /* T5 */
> >>>>> + MATRIX_KEY(0x02, 0x04, 0) /* T6 */
> >>>>> + MATRIX_KEY(0x01, 0x04, 0) /* T7 */
> >>>>> + MATRIX_KEY(0x02, 0x09, 0) /* T8 */
> >>>>> + MATRIX_KEY(0x01, 0x09, 0) /* T9 */
> >>>>> + MATRIX_KEY(0x00, 0x04, 0) /* T10 */
> >>>>> + >;
> >>>>> +
> >>>>> + linux,keymap = <
> >>>>> + MATRIX_KEY(0x00, 0x02, KEY_BACK)
> >>>>> + MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
> >>>>> + MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
> >>>>> + MATRIX_KEY(0x01, 0x02, KEY_SCALE)
> >>>>> + MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
> >>>>> + MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
> >>>>> + MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
> >>>>> + MATRIX_KEY(0x02, 0x09, KEY_MUTE)
> >>>>> + MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
> >>>>> + MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
> >>>>> + CROS_STD_MAIN_KEYMAP
> >>>>> + >;
> >>>>> +};
> >>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> >>>>> new file mode 100644
> >>>>> index 000000000000..447b57b12b41
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola-tentacruel-sku262148.dts
> >>>>> @@ -0,0 +1,26 @@
> >>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>>>> +/*
> >>>>> + * Copyright 2023 Google LLC
> >>>>> + */
> >>>>> +
> >>>>> +#include "mt8186-corsola-tentacruel-sku262144.dts"
> >>>>> +
> >>>>> +/ {
> >>>>> + compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
> >>>>> + "google,tentacruel-sku262149", "google,tentacruel-sku262148",
> >>>>> + "google,tentacruel", "mediatek,mt8186";
> >>>>> +};
> >>>>> +
> >>>>> +/* This variant replaces only the trackpad controller. */
> >>>>> +&i2c2 {
> >>>>> + /delete-node/ trackpad@15;
> >>>>> +
> >>>>> + trackpad@15 {
> >>>>> + compatible = "hid-over-i2c";
> >>>>> + reg = <0x15>;
> >>>>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> >>>>> + hid-descr-addr = <0x0001>;
> >>>>> + vdd-supply = <&pp3300_s3>;
> >>>>> + wakeup-source;
> >>>>> + };
> >>>>> +};
> >>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> >>>>> new file mode 100644
> >>>>> index 000000000000..8726b2916ef1
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8186-corsola.dtsi
> >>>>> @@ -0,0 +1,1719 @@
> >>>>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> >>>>> +/*
> >>>>> + * Copyright (C) 2022 MediaTek Inc.
> >>>>> + */
> >>>>> +/dts-v1/;
> >>>>> +#include "mt8186.dtsi"
> >>>>> +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> >>>>> +#include <dt-bindings/gpio/gpio.h>
> >>>>> +#include <dt-bindings/input/input.h>
> >>>>> +#include <dt-bindings/input/gpio-keys.h>
> >>>>> +#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
> >>>>> +
> >>>>> +/ {
> >>>>> + aliases {
> >>>>> + i2c0 = &i2c0;
> >>>>> + i2c1 = &i2c1;
> >>>>> + i2c2 = &i2c2;
> >>>>> + i2c3 = &i2c3;
> >>>>> + i2c5 = &i2c5;
> >>>>> + mmc0 = &mmc0;
> >>>>> + mmc1 = &mmc1;
> >>>>> + serial0 = &uart0;
> >>>>> + };
> >>>>> +
> >>>>> + chosen {
> >>>>> + stdout-path = "serial0:115200n8";
> >>>>> + };
> >>>>> +
> >>>>> + memory@40000000 {
> >>>>> + device_type = "memory";
> >>>>> + /* The size should be filled in by the bootloader. */
> >>>>> + reg = <0 0x40000000 0 0>;
> >>>>> + };
> >>>>> +
> >>>>> + backlight_lcd0: backlight-lcd0 {
> >>>>> + compatible = "pwm-backlight";
> >>>>> + pwms = <&pwm0 0 500000>;
> >>>>> + power-supply = <&ppvar_sys>;
> >>>>> + enable-gpios = <&pio 152 0>;
> >>>>> + brightness-levels = <0 1023>;
> >>>>> + num-interpolated-steps = <1023>;
> >>>>> + default-brightness-level = <576>;
> >>>>> + };
> >>>>> +
> >>>>> + btsco: bt-sco {
> >>>>
> >>>> Do you really need the phandle to bt-sco?
> >>>
> >>> No. But the sound node probably should be referencing it and the dmic
> >>> node via DT instead of hardcoding the DAI and codec names in the machine
> >>> driver.
> >>>
> >>> Anyway, will remove the label for now.
> >>>
> >>>> Also, this node describes a codec, so: "bt-sco-codec" please!
> >>>
> >>> Ack.
> >>>
> >>>>> + compatible = "linux,bt-sco";
> >>>>> + #sound-dai-cells = <0>;
> >>>>> + };
> >>>>> +
> >>>>> + dmic_codec: dmic-codec {
> >>>>
> >>>> This phandle is unused...
> >>>
> >>> Removed.
> >>>
> >>>> ..snip..
> >>>>
> >>>>> +
> >>>>> +&adsp {
> >>>>> + memory-region = <&adsp_dma_mem>, <&adsp_mem>;
> >>>>> + status = "disabled"; /* causes stall */
> >>>>
> >>>> This is a firmware issue: once the correct firmware is uploaded to linux-firmware
> >>>> the dsp node can get enabled... so it we make sure that this happens before this
> >>>> devicetree gets picked, we can avoid a second commit enabling audio.
> >>>>
> >>>> After all, since we *want to* use the Xtensa DSP for audio, without it booted
> >>>> sound won't work *anyway*.... so having the firmware in place can also be seen
> >>>> as a direct dependency of the entire audio functionality.
> >>>>
> >>>> P.S.: The FW that is distributed with ChromeOS works just fine!
> >>>
> >>> I'll give that a try.
> >>
> >> I have:
> >>
> >> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
> >> sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
> >> sof-audio-of-mt8186 10680000.adsp: unknown sof_ext_man header type 3 size 0x30
> >> sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-5494c
> >>
> >> and it's still hanging.
> >
> > Looks like I was still using the bad version due to module options...
> >
> > After removing the options, I now have:
> >
> > sof-audio-of-mt8186 10680000.adsp: DT DSP detected
> > sof-audio-of-mt8186 10680000.adsp: assigned reserved memory node memory@61000000
> > sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-714c6
> > sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
> > sof-audio-of-mt8186 10680000.adsp: unknown sof_ext_man header type 3 size 0x30
> > sof-audio-of-mt8186 10680000.adsp: Firmware info: version 2:0:0-714c6
> > sof-audio-of-mt8186 10680000.adsp: Firmware: ABI 3:22:1 Kernel ABI 3:23:0
> >
> > But sound is still deferring probe:
> >
> > # cat /sys/kernel/debug/devices_deferred
> > sound mt8186_mt6366_rt1019_rt5682s:
> > mt8186_mt6366_rt1019_rt5682s_dev_probe snd_soc_register_card fail
> >
>
> Yes, this happens because of the missing IT6505 HDMI audio support - but it's not
> giving any side effect anyway... in this case, as far as DT is concerned... there
> will be no change, and no side effects on working parts of the system, so we can
> (imo) upstream this even if the driver-code-only dependency is not there yet.
I have the it6505 audio patches backported. But maybe they don't actually
work anymore. :(
> Cheers!
> Angelo
>
> > ChenYu
> >
> >> And FTR, I think sound is also blocked on the it6505 audio support series.
> >>
> >> ChenYu
> >>
> >>
> >>
> >>>>> +};
> >>>>> +
> >>>>> +&afe {
> >>>>> + i2s0-share = "I2S1";
> >>>>> + i2s3-share = "I2S2";
> >>>>> + status = "okay";
> >>>>> +};
> >>>>> +
> >>>>
> >>>> ..snip..
> >>>>
> >>>>> +&i2c2 {
> >>>>> + pinctrl-names = "default";
> >>>>> + /*
> >>>>> + * Trackpad pin put here to work around second source components
> >>>>> + * sharing the pinmux in steelix designs.
> >>>>> + */
> >>>>> + pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
> >>>>
> >>>> There's no choice for now... even if this is not beautiful to see... but it's still
> >>>> ok for me because we can revisit this later when the HW Prober mechanism will be
> >>>> upstreamed.
> >>>
> >>> Yup. Working on that.
> >>>
> >>>>> + clock-frequency = <400000>;
> >>>>> + i2c-scl-internal-delay-ns = <10000>;
> >>>>> + status = "okay";
> >>>>> +
> >>>>> + trackpad@15 {
> >>>>> + compatible = "elan,ekth3000";
> >>>>> + reg = <0x15>;
> >>>>> + interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
> >>>>> + vcc-supply = <&pp3300_s3>;
> >>>>> + wakeup-source;
> >>>>> + };
> >>>>> +};
> >>>>> +
> >>>>
> >>>> Thanks,
> >>>> Angelo
> >>>
> >>> Thanks for the review again.
> >>>
> >>> ChenYu
>
@@ -43,6 +43,10 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327681.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacool-sku327683.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262144.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-corsola-tentacruel-sku262148.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r5-sku2.dtb
new file mode 100644
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2022 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8186-corsola.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ aliases {
+ i2c4 = &i2c4;
+ };
+};
+
+&dsi_out {
+ remote-endpoint = <&ps8640_in>;
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+
+ ps8640: edp-bridge@8 {
+ compatible = "parade,ps8640";
+ reg = <0x8>;
+ powerdown-gpios = <&pio 96 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&pio 98 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ps8640_pins>;
+ vdd12-supply = <&mt6366_vrf12_reg>;
+ vdd33-supply = <&mt6366_vcn33_reg>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ ps8640_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ ps8640_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+
+ aux-bus {
+ panel {
+ compatible = "edp-panel";
+ power-supply = <&pp3300_disp_x>;
+ backlight = <&backlight_lcd0>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&ps8640_out>;
+ };
+ };
+ };
+ };
+ };
+};
+
+&i2c1 {
+ i2c-scl-internal-delay-ns = <10000>;
+
+ touchscreen: touchscreen@10 {
+ compatible = "hid-over-i2c";
+ reg = <0x10>;
+ interrupts-extended = <&pio 12 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touchscreen_pins>;
+ post-power-on-delay-ms = <10>;
+ hid-descr-addr = <0x0001>;
+ vdd-supply = <&pp3300_s3>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ proximity@28 {
+ compatible = "semtech,sx9324";
+ reg = <0x28>;
+ interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sar_sensor_pins>;
+ vdd-supply = <&mt6366_vio18_reg>;
+ svdd-supply = <&mt6366_vio18_reg>;
+ #io-channel-cells = <1>;
+ };
+};
+
+&pio {
+ i2c4_pins: i2c4-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
+ <PINMUX_GPIO135__FUNC_SCL4>;
+ bias-disable;
+ drive-strength = <4>;
+ input-enable;
+ };
+ };
+
+ ps8640_pins: ps8640-pins {
+ pins-pwrdn-rst {
+ pinmux = <PINMUX_GPIO96__FUNC_GPIO96>,
+ <PINMUX_GPIO98__FUNC_GPIO98>;
+ output-low;
+ };
+ };
+
+ sar_sensor_pins: sar-sensor-pins {
+ pins-irq {
+ pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
+ input-enable;
+ bias-pull-up;
+ };
+ };
+};
new file mode 100644
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2022 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8186-corsola-krabby.dtsi"
+
+/ {
+ model = "Google Tentacool board";
+ compatible = "google,tentacruel-sku327681", "google,tentacruel", "mediatek,mt8186";
+ chassis-type = "laptop";
+};
+
+/* Tentacool omits the pen. */
+&gpio_keys {
+ status = "disabled";
+};
+
+/* Tentacool omits the touchscreen; nothing else is on i2c1. */
+&i2c1 {
+ status = "disabled";
+};
+
+&keyboard_controller {
+ function-row-physmap = <
+ MATRIX_KEY(0x00, 0x02, 0) /* T1 */
+ MATRIX_KEY(0x03, 0x02, 0) /* T2 */
+ MATRIX_KEY(0x02, 0x02, 0) /* T3 */
+ MATRIX_KEY(0x01, 0x02, 0) /* T4 */
+ MATRIX_KEY(0x03, 0x04, 0) /* T5 */
+ MATRIX_KEY(0x02, 0x04, 0) /* T6 */
+ MATRIX_KEY(0x01, 0x04, 0) /* T7 */
+ MATRIX_KEY(0x02, 0x09, 0) /* T8 */
+ MATRIX_KEY(0x01, 0x09, 0) /* T9 */
+ MATRIX_KEY(0x00, 0x04, 0) /* T10 */
+ >;
+
+ linux,keymap = <
+ MATRIX_KEY(0x00, 0x02, KEY_BACK)
+ MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+ MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
+ MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+ MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+ MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+ MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+ MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+ MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+ MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+ CROS_STD_MAIN_KEYMAP
+ >;
+};
+
+/* Tentacool omits the touchscreen. */
+&touchscreen {
+ status = "disabled";
+};
new file mode 100644
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2023 Google LLC
+ */
+
+#include "mt8186-corsola-tentacool-sku327681.dts"
+
+/ {
+ compatible = "google,tentacruel-sku327683", "google,tentacruel", "mediatek,mt8186";
+};
+
+/* This variant replaces only the trackpad controller. */
+&i2c2 {
+ /delete-node/ trackpad@15;
+
+ trackpad@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+ interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
+ hid-descr-addr = <0x0001>;
+ vdd-supply = <&pp3300_s3>;
+ wakeup-source;
+ };
+};
new file mode 100644
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2022 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8186-corsola-krabby.dtsi"
+
+/ {
+ model = "Google Tentacruel board";
+ compatible = "google,tentacruel-sku262147", "google,tentacruel-sku262146",
+ "google,tentacruel-sku262145", "google,tentacruel-sku262144",
+ "google,tentacruel", "mediatek,mt8186";
+ chassis-type = "convertible";
+};
+
+&keyboard_controller {
+ function-row-physmap = <
+ MATRIX_KEY(0x00, 0x02, 0) /* T1 */
+ MATRIX_KEY(0x03, 0x02, 0) /* T2 */
+ MATRIX_KEY(0x02, 0x02, 0) /* T3 */
+ MATRIX_KEY(0x01, 0x02, 0) /* T4 */
+ MATRIX_KEY(0x03, 0x04, 0) /* T5 */
+ MATRIX_KEY(0x02, 0x04, 0) /* T6 */
+ MATRIX_KEY(0x01, 0x04, 0) /* T7 */
+ MATRIX_KEY(0x02, 0x09, 0) /* T8 */
+ MATRIX_KEY(0x01, 0x09, 0) /* T9 */
+ MATRIX_KEY(0x00, 0x04, 0) /* T10 */
+ >;
+
+ linux,keymap = <
+ MATRIX_KEY(0x00, 0x02, KEY_BACK)
+ MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+ MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
+ MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+ MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+ MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+ MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+ MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+ MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+ MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+ CROS_STD_MAIN_KEYMAP
+ >;
+};
new file mode 100644
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2023 Google LLC
+ */
+
+#include "mt8186-corsola-tentacruel-sku262144.dts"
+
+/ {
+ compatible = "google,tentacruel-sku262151", "google,tentacruel-sku262150",
+ "google,tentacruel-sku262149", "google,tentacruel-sku262148",
+ "google,tentacruel", "mediatek,mt8186";
+};
+
+/* This variant replaces only the trackpad controller. */
+&i2c2 {
+ /delete-node/ trackpad@15;
+
+ trackpad@15 {
+ compatible = "hid-over-i2c";
+ reg = <0x15>;
+ interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
+ hid-descr-addr = <0x0001>;
+ vdd-supply = <&pp3300_s3>;
+ wakeup-source;
+ };
+};
new file mode 100644
@@ -0,0 +1,1719 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+/dts-v1/;
+#include "mt8186.dtsi"
+#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
+
+/ {
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c5 = &i2c5;
+ mmc0 = &mmc0;
+ mmc1 = &mmc1;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@40000000 {
+ device_type = "memory";
+ /* The size should be filled in by the bootloader. */
+ reg = <0 0x40000000 0 0>;
+ };
+
+ backlight_lcd0: backlight-lcd0 {
+ compatible = "pwm-backlight";
+ pwms = <&pwm0 0 500000>;
+ power-supply = <&ppvar_sys>;
+ enable-gpios = <&pio 152 0>;
+ brightness-levels = <0 1023>;
+ num-interpolated-steps = <1023>;
+ default-brightness-level = <576>;
+ };
+
+ btsco: bt-sco {
+ compatible = "linux,bt-sco";
+ #sound-dai-cells = <0>;
+ };
+
+ dmic_codec: dmic-codec {
+ compatible = "dmic-codec";
+ num-channels = <2>;
+ wakeup-delay-ms = <50>;
+ #sound-dai-cells = <0>;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pen_eject>;
+
+ pen_insert: pen-insert-switch {
+ label = "Pen Insert";
+ /* Insert = low, eject = high */
+ gpios = <&pio 18 GPIO_ACTIVE_LOW>;
+ linux,code = <SW_PEN_INSERTED>;
+ linux,input-type = <EV_SW>;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ wakeup-source;
+ };
+ };
+
+ pp1800_dpbrdg_dx: regulator-pp1800-dpbrdg-dx {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&en_pp1800_dpbrdg>;
+ regulator-name = "pp1800_dpbrdg_dx";
+ enable-active-high;
+ gpio = <&pio 39 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&mt6366_vio18_reg>;
+ };
+
+ pp3300_disp_x: regulator-pp3300-disp-x {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_disp_x";
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_panel_fixed_pins>;
+ enable-active-high;
+ regulator-boot-on;
+ gpio = <&pio 153 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&pp3300_z2>;
+ };
+
+ /* system wide LDO 3.3V power rail */
+ pp3300_z5: regulator-pp3300-ldo-z5 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_ldo_z5";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&ppvar_sys>;
+ };
+
+ /* separately switched 3.3V power rail */
+ pp3300_s3: regulator-pp3300-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_s3";
+ /* automatically sequenced by PMIC EXT_PMIC_EN2 */
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&pp3300_z2>;
+ };
+
+ /* system wide 3.3V power rail */
+ pp3300_z2: regulator-pp3300-z2 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_z2";
+ /* EN pin tied to pp4200_z2, which is controlled by EC */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&ppvar_sys>;
+ };
+
+ /* system wide 4.2V power rail */
+ pp4200_z2: regulator-pp4200-z2 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp4200_z2";
+ /* controlled by EC */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <4200000>;
+ regulator-max-microvolt = <4200000>;
+ vin-supply = <&ppvar_sys>;
+ };
+
+ /* system wide switching 5.0V power rail */
+ pp5000_z2: regulator-pp5000-z2 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp5000_z2";
+ /* controlled by EC */
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&ppvar_sys>;
+ };
+
+ /* system wide semi-regulated power rail from battery or USB */
+ ppvar_sys: regulator-ppvar-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvar_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reserved_memory: reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ adsp_dma_mem: memory@61000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x61000000 0 0x100000>;
+ no-map;
+ };
+
+ adsp_mem: memory@60000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x60000000 0 0xA00000>;
+ no-map;
+ };
+
+ scp_mem: memory@50000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x50000000 0 0x10a0000>;
+ no-map;
+ };
+ };
+
+ sound: sound {
+ compatible = "mediatek,mt8186-mt6366-rt1019-rt5682s-sound";
+ pinctrl-names = "aud_clk_mosi_off",
+ "aud_clk_mosi_on",
+ "aud_clk_miso_off",
+ "aud_clk_miso_on",
+ "aud_dat_miso_off",
+ "aud_dat_miso_on",
+ "aud_dat_mosi_off",
+ "aud_dat_mosi_on",
+ "aud_gpio_i2s0_off",
+ "aud_gpio_i2s0_on",
+ "aud_gpio_i2s1_off",
+ "aud_gpio_i2s1_on",
+ "aud_gpio_i2s2_off",
+ "aud_gpio_i2s2_on",
+ "aud_gpio_i2s3_off",
+ "aud_gpio_i2s3_on",
+ "aud_gpio_tdm_off",
+ "aud_gpio_tdm_on",
+ "aud_gpio_pcm_off",
+ "aud_gpio_pcm_on",
+ "aud_gpio_dmic_sec";
+ pinctrl-0 = <&aud_clk_mosi_off>;
+ pinctrl-1 = <&aud_clk_mosi_on>;
+ pinctrl-2 = <&aud_clk_miso_off>;
+ pinctrl-3 = <&aud_clk_miso_on>;
+ pinctrl-4 = <&aud_dat_miso_off>;
+ pinctrl-5 = <&aud_dat_miso_on>;
+ pinctrl-6 = <&aud_dat_mosi_off>;
+ pinctrl-7 = <&aud_dat_mosi_on>;
+ pinctrl-8 = <&aud_gpio_i2s0_off>;
+ pinctrl-9 = <&aud_gpio_i2s0_on>;
+ pinctrl-10 = <&aud_gpio_i2s1_off>;
+ pinctrl-11 = <&aud_gpio_i2s1_on>;
+ pinctrl-12 = <&aud_gpio_i2s2_off>;
+ pinctrl-13 = <&aud_gpio_i2s2_on>;
+ pinctrl-14 = <&aud_gpio_i2s3_off>;
+ pinctrl-15 = <&aud_gpio_i2s3_on>;
+ pinctrl-16 = <&aud_gpio_tdm_off>;
+ pinctrl-17 = <&aud_gpio_tdm_on>;
+ pinctrl-18 = <&aud_gpio_pcm_off>;
+ pinctrl-19 = <&aud_gpio_pcm_on>;
+ pinctrl-20 = <&aud_gpio_dmic_sec>;
+ mediatek,adsp = <&adsp>;
+ mediatek,platform = <&afe>;
+
+ playback-codecs {
+ sound-dai = <&it6505dptx>, <&rt1019p>;
+ };
+
+ headset-codec {
+ sound-dai = <&rt5682s 0>;
+ };
+ };
+
+ rt1019p: speaker-codec {
+ compatible = "realtek,rt1019p";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rt1019p_pins_default>;
+ sdb-gpios = <&pio 150 GPIO_ACTIVE_HIGH>;
+ #sound-dai-cells = <0>;
+ };
+
+ usb_p1_vbus: regulator-usb-p1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "vbus1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&pio 148 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&pp5000_z2>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_enable_pin>;
+ post-power-on-delay-ms = <50>;
+ reset-gpios = <&pio 54 GPIO_ACTIVE_LOW>;
+ };
+
+ wifi_wakeup: wifi-wakeup {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_wakeup_pin>;
+
+ wowlan-event {
+ label = "Wake on WiFi";
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+ };
+};
+
+&adsp {
+ memory-region = <&adsp_dma_mem>, <&adsp_mem>;
+ status = "disabled"; /* causes stall */
+};
+
+&afe {
+ i2s0-share = "I2S1";
+ i2s3-share = "I2S2";
+ status = "okay";
+};
+
+&cci {
+ proc-supply = <&mt6366_vproc12_reg>;
+};
+
+&cpu0 {
+ proc-supply = <&mt6366_vproc12_reg>;
+};
+
+&cpu1 {
+ proc-supply = <&mt6366_vproc12_reg>;
+};
+
+&cpu2 {
+ proc-supply = <&mt6366_vproc12_reg>;
+};
+
+&cpu3 {
+ proc-supply = <&mt6366_vproc12_reg>;
+};
+
+&cpu4 {
+ proc-supply = <&mt6366_vproc12_reg>;
+};
+
+&cpu5 {
+ proc-supply = <&mt6366_vproc12_reg>;
+};
+
+&cpu6 {
+ proc-supply = <&mt6366_vproc11_reg>;
+};
+
+&cpu7 {
+ proc-supply = <&mt6366_vproc11_reg>;
+};
+
+&dpi {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&dpi_pins_default>;
+ pinctrl-1 = <&dpi_pins_sleep>;
+ status = "okay";
+};
+
+&dpi_out {
+ remote-endpoint = <&it6505_in>;
+};
+
+&dsi0 {
+ status = "okay";
+};
+
+&gic {
+ mediatek,broken-save-restore-fw;
+};
+
+&gpu {
+ mali-supply = <&mt6366_vgpu_reg>;
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ clock-frequency = <400000>;
+ i2c-scl-internal-delay-ns = <8000>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ /*
+ * Trackpad pin put here to work around second source components
+ * sharing the pinmux in steelix designs.
+ */
+ pinctrl-0 = <&i2c2_pins>, <&trackpad_pin>;
+ clock-frequency = <400000>;
+ i2c-scl-internal-delay-ns = <10000>;
+ status = "okay";
+
+ trackpad@15 {
+ compatible = "elan,ekth3000";
+ reg = <0x15>;
+ interrupts-extended = <&pio 11 IRQ_TYPE_LEVEL_LOW>;
+ vcc-supply = <&pp3300_s3>;
+ wakeup-source;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ clock-frequency = <100000>;
+ status = "okay";
+
+ it6505dptx: dp-bridge@5c {
+ compatible = "ite,it6505";
+ reg = <0x5c>;
+ interrupts-extended = <&pio 8 IRQ_TYPE_LEVEL_LOW>;
+ ovdd-supply = <&mt6366_vsim2_reg>;
+ pwr18-supply = <&pp1800_dpbrdg_dx>;
+ reset-gpios = <&pio 177 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&it6505_pins>;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ it6505_in: endpoint {
+ link-frequencies = /bits/ 64 <150000000>;
+ remote-endpoint = <&dpi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ };
+ };
+ };
+};
+
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+ status = "okay";
+
+ rt5682s: codec@1a {
+ compatible = "realtek,rt5682s";
+ reg = <0x1a>;
+ interrupts-extended = <&pio 17 IRQ_TYPE_EDGE_BOTH>;
+ AVDD-supply = <&mt6366_vio18_reg>;
+ DBVDD-supply = <&mt6366_vio18_reg>;
+ LDO1-IN-supply = <&mt6366_vio18_reg>;
+ MICVDD-supply = <&pp3300_z2>;
+ realtek,jd-src = <1>;
+ #sound-dai-cells = <1>;
+ };
+};
+
+&mfg0 {
+ domain-supply = <&mt6366_vsram_gpu_reg>;
+};
+
+&mfg1 {
+ domain-supply = <&mt6366_vgpu_reg>;
+};
+
+&mipi_tx0 {
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ non-removable;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ supports-cqe;
+ no-sd;
+ no-sdio;
+ cap-mmc-hw-reset;
+ hs400-ds-delay = <0x11814>;
+ mediatek,hs400-ds-dly3 = <0x14>;
+ vmmc-supply = <&mt6366_vemc_reg>;
+ vqmmc-supply = <&mt6366_vio18_reg>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default", "state_uhs", "state_eint";
+ pinctrl-0 = <&mmc1_pins_default>;
+ pinctrl-1 = <&mmc1_pins_uhs>;
+ pinctrl-2 = <&mmc1_pins_eint>;
+ /delete-property/ interrupts;
+ interrupt-names = "msdc", "sdio_wakeup";
+ interrupts-extended = <&gic GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH 0>,
+ <&pio 87 IRQ_TYPE_LEVEL_LOW>;
+ bus-width = <4>;
+ max-frequency = <200000000>;
+ cap-sd-highspeed;
+ sd-uhs-sdr104;
+ sd-uhs-sdr50;
+ keep-power-in-suspend;
+ wakeup-source;
+ cap-sdio-irq;
+ no-mmc;
+ no-sd;
+ non-removable;
+ vmmc-supply = <&pp3300_s3>;
+ vqmmc-supply = <&mt6366_vio18_reg>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bluetooth@2 {
+ compatible = "mediatek,mt7921s-bluetooth";
+ reg = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_pins_reset>;
+ reset-gpios = <&pio 155 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&nor_flash {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nor_pins_default>;
+ assigned-clock-parents = <&topckgen CLK_TOP_MAINPLL_D7_D4>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <39000000>;
+ };
+};
+
+&pio {
+ /* 185 lines */
+ gpio-line-names = "TP",
+ "TP",
+ "TP",
+ "I2S0_HP_DI",
+ "I2S3_DP_SPKR_DO",
+ "SAR_INT_ODL",
+ "BT_WAKE_AP_ODL",
+ "WIFI_INT_ODL",
+ "DPBRDG_INT_ODL",
+ "EDPBRDG_INT_ODL",
+ "EC_AP_HPD_OD",
+ "TCHPAD_INT_ODL",
+ "TCHSCR_INT_1V8_ODL",
+ "EC_AP_INT_ODL",
+ "EC_IN_RW_ODL",
+ "GSC_AP_INT_ODL",
+ /* AP_FLASH_WP_L is crossystem ABI. Rev1 schematics call it AP_WP_ODL. */
+ "AP_FLASH_WP_L",
+ "HP_INT_ODL",
+ "PEN_EJECT_OD",
+ "WCAM_PWDN_L",
+ "WCAM_RST_L",
+ "UCAM_SEN_EN",
+ "UCAM_RST_L",
+ "LTE_RESET_L",
+ "LTE_SAR_DETECT_L",
+ "I2S2_DP_SPK_MCK",
+ "I2S2_DP_SPKR_BCK",
+ "I2S2_DP_SPKR_LRCK",
+ "I2S2_DP_SPKR_DI (TP)",
+ "EN_PP1000_EDPBRDG",
+ "EN_PP1800_EDPBRDG",
+ "EN_PP3300_EDPBRDG",
+ "UART_GSC_TX_AP_RX",
+ "UART_AP_TX_GSC_RX",
+ "UART_DBGCON_TX_ADSP_RX",
+ "UART_ADSP_TX_DBGCON_RX",
+ "EN_PP1000_DPBRDG",
+ "TCHSCR_REPORT_DISABLE",
+ "EN_PP3300_DPBRDG",
+ "EN_PP1800_DPBRDG",
+ "SPI_AP_CLK_EC",
+ "SPI_AP_CS_EC_L",
+ "SPI_AP_DO_EC_DI",
+ "SPI_AP_DI_EC_DO",
+ "SPI_AP_CLK_GSC",
+ "SPI_AP_CS_GSC_L",
+ "SPI_AP_DO_GSC_DI",
+ "SPI_AP_DI_GSC_DO",
+ "UART_DBGCON_TX_SCP_RX",
+ "UART_SCP_TX_DBGCON_RX",
+ "EN_PP1200_CAM_X",
+ "EN_PP2800A_VCM_X",
+ "EN_PP2800A_UCAM_X",
+ "EN_PP2800A_WCAM_X",
+ "WLAN_MODULE_RST_L",
+ "EN_PP1200_UCAM_X",
+ "I2S1_HP_DO",
+ "I2S1_HP_BCK",
+ "I2S1_HP_LRCK",
+ "I2S1_HP_MCK",
+ "TCHSCR_RST_1V8_L",
+ "SPI_AP_CLK_ROM",
+ "SPI_AP_CS_ROM_L",
+ "SPI_AP_DO_ROM_DI",
+ "SPI_AP_DI_ROM_DO",
+ "NC",
+ "NC",
+ "EMMC_STRB",
+ "EMMC_CLK",
+ "EMMC_CMD",
+ "EMMC_RST_L",
+ "EMMC_DATA0",
+ "EMMC_DATA1",
+ "EMMC_DATA2",
+ "EMMC_DATA3",
+ "EMMC_DATA4",
+ "EMMC_DATA5",
+ "EMMC_DATA6",
+ "EMMC_DATA7",
+ "AP_KPCOL0",
+ "NC",
+ "NC",
+ "NC",
+ "TP",
+ "SDIO_CLK",
+ "SDIO_CMD",
+ "SDIO_DATA0",
+ "SDIO_DATA1",
+ "SDIO_DATA2",
+ "SDIO_DATA3",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "NC",
+ "EDPBRDG_PWREN",
+ "BL_PWM_1V8",
+ "EDPBRDG_RST_L",
+ "MIPI_DPI_CLK",
+ "MIPI_DPI_VSYNC",
+ "MIPI_DPI_HSYNC",
+ "MIPI_DPI_DE",
+ "MIPI_DPI_D0",
+ "MIPI_DPI_D1",
+ "MIPI_DPI_D2",
+ "MIPI_DPI_D3",
+ "MIPI_DPI_D4",
+ "MIPI_DPI_D5",
+ "MIPI_DPI_D6",
+ "MIPI_DPI_DA7",
+ "MIPI_DPI_D8",
+ "MIPI_DPI_D9",
+ "MIPI_DPI_D10",
+ "MIPI_DPI_D11",
+ "PCM_BT_CLK",
+ "PCM_BT_SYNC",
+ "PCM_BT_DI",
+ "PCM_BT_DO",
+ "JTAG_TMS_TP",
+ "JTAG_TCK_TP",
+ "JTAG_TDI_TP",
+ "JTAG_TDO_TP",
+ "JTAG_TRSTN_TP",
+ "CLK_24M_WCAM",
+ "CLK_24M_UCAM",
+ "UCAM_DET_ODL",
+ "AP_I2C_EDPBRDG_SCL_1V8",
+ "AP_I2C_EDPBRDG_SDA_1V8",
+ "AP_I2C_TCHSCR_SCL_1V8",
+ "AP_I2C_TCHSCR_SDA_1V8",
+ "AP_I2C_TCHPAD_SCL_1V8",
+ "AP_I2C_TCHPAD_SDA_1V8",
+ "AP_I2C_DPBRDG_SCL_1V8",
+ "AP_I2C_DPBRDG_SDA_1V8",
+ "AP_I2C_WLAN_SCL_1V8",
+ "AP_I2C_WLAN_SDA_1V8",
+ "AP_I2C_AUD_SCL_1V8",
+ "AP_I2C_AUD_SDA_1V8",
+ "AP_I2C_TPM_SCL_1V8",
+ "AP_I2C_UCAM_SDA_1V8",
+ "AP_I2C_UCAM_SCL_1V8",
+ "AP_I2C_UCAM_SDA_1V8",
+ "AP_I2C_WCAM_SCL_1V8",
+ "AP_I2C_WCAM_SDA_1V8",
+ "SCP_I2C_SENSOR_SCL_1V8",
+ "SCP_I2C_SENSOR_SDA_1V8",
+ "AP_EC_WARM_RST_REQ",
+ "AP_XHCI_INIT_DONE",
+ "USB3_HUB_RST_L",
+ "EN_SPKR",
+ "BEEP_ON",
+ "AP_EDP_BKLTEN",
+ "EN_PP3300_DISP_X",
+ "EN_PP3300_SDBRDG_X",
+ "BT_KILL_1V8_L",
+ "WIFI_KILL_1V8_L",
+ "PWRAP_SPI0_CSN",
+ "PWRAP_SPI0_CK",
+ "PWRAP_SPI0_MO",
+ "PWRAP_SPI0_MI",
+ "SRCLKENA0",
+ "SRCLKENA1",
+ "SCP_VREQ_VAO",
+ "AP_RTC_CLK32K",
+ "AP_PMIC_WDTRST_L",
+ "AUD_CLK_MOSI",
+ "AUD_SYNC_MOSI",
+ "AUD_DAT_MOSI0",
+ "AUD_DAT_MOSI1",
+ "AUD_CLK_MISO",
+ "AUD_SYNC_MISO",
+ "AUD_DAT_MISO0",
+ "AUD_DAT_MISO1",
+ "NC",
+ "NC",
+ "DPBRDG_PWREN",
+ "DPBRDG_RST_L",
+ "LTE_W_DISABLE_L",
+ "LTE_SAR_DETECT_L",
+ "EN_PP3300_LTE_X",
+ "LTE_PWR_OFF_L",
+ "LTE_RESET_L",
+ "TP",
+ "TP";
+
+ aud_clk_mosi_off: aud-clk-mosi-off-pins {
+ pins-clk-sync {
+ pinmux = <PINMUX_GPIO166__FUNC_GPIO166>,
+ <PINMUX_GPIO167__FUNC_GPIO167>;
+ input-enable;
+ bias-pull-down;
+ };
+ };
+
+ aud_clk_mosi_on: aud-clk-mosi-on-pins {
+ pins-clk-sync {
+ pinmux = <PINMUX_GPIO166__FUNC_AUD_CLK_MOSI>,
+ <PINMUX_GPIO167__FUNC_AUD_SYNC_MOSI>;
+ };
+ };
+
+ aud_clk_miso_off: aud-clk-miso-off-pins {
+ pins-clk-sync {
+ pinmux = <PINMUX_GPIO170__FUNC_GPIO170>,
+ <PINMUX_GPIO171__FUNC_GPIO171>;
+ input-enable;
+ bias-pull-down;
+ };
+ };
+
+ aud_clk_miso_on: aud-clk-miso-on-pins {
+ pins-clk-sync {
+ pinmux = <PINMUX_GPIO170__FUNC_AUD_CLK_MISO>,
+ <PINMUX_GPIO171__FUNC_AUD_SYNC_MISO>;
+ };
+ };
+
+ aud_dat_mosi_off: aud-dat-mosi-off-pins {
+ pins-dat {
+ pinmux = <PINMUX_GPIO168__FUNC_GPIO168>,
+ <PINMUX_GPIO169__FUNC_GPIO169>;
+ input-enable;
+ bias-pull-down;
+ };
+ };
+
+ aud_dat_mosi_on: aud-dat-mosi-on-pins {
+ pins-dat {
+ pinmux = <PINMUX_GPIO168__FUNC_AUD_DAT_MOSI0>,
+ <PINMUX_GPIO169__FUNC_AUD_DAT_MOSI1>;
+ };
+ };
+
+ aud_dat_miso_off: aud-dat-miso-off-pins {
+ pins-dat {
+ pinmux = <PINMUX_GPIO172__FUNC_GPIO172>,
+ <PINMUX_GPIO173__FUNC_GPIO173>;
+ input-enable;
+ bias-pull-down;
+ };
+ };
+
+ aud_dat_miso_on: aud-dat-miso-on-pins {
+ pins-dat {
+ pinmux = <PINMUX_GPIO172__FUNC_AUD_DAT_MISO0>,
+ <PINMUX_GPIO173__FUNC_AUD_DAT_MISO1>;
+ input-schmitt-enable;
+ bias-disable;
+ };
+ };
+
+ aud_gpio_i2s0_off: aud-gpio-i2s0-off-pins {
+ pins-sdata {
+ pinmux = <PINMUX_GPIO3__FUNC_GPIO3>;
+ };
+ };
+
+ aud_gpio_i2s0_on: aud-gpio-i2s0-on-pins {
+ pins-sdata {
+ pinmux = <PINMUX_GPIO3__FUNC_I2S0_DI>;
+ };
+ };
+
+ aud_gpio_i2s1_off: aud-gpio-i2s-off-pins {
+ pins-clk-sdata {
+ pinmux = <PINMUX_GPIO56__FUNC_GPIO56>,
+ <PINMUX_GPIO57__FUNC_GPIO57>,
+ <PINMUX_GPIO58__FUNC_GPIO58>,
+ <PINMUX_GPIO59__FUNC_GPIO59>;
+ output-low;
+ };
+ };
+
+ aud_gpio_i2s1_on: aud-gpio-i2s1-on-pins {
+ pins-clk-sdata {
+ pinmux = <PINMUX_GPIO56__FUNC_I2S1_DO>,
+ <PINMUX_GPIO57__FUNC_I2S1_BCK>,
+ <PINMUX_GPIO58__FUNC_I2S1_LRCK>,
+ <PINMUX_GPIO59__FUNC_I2S1_MCK>;
+ };
+ };
+
+ aud_gpio_i2s2_off: aud-gpio-i2s2-off-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO26__FUNC_GPIO26>,
+ <PINMUX_GPIO27__FUNC_GPIO27>;
+ output-low;
+ };
+ };
+
+ aud_gpio_i2s2_on: aud-gpio-i2s2-on-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO26__FUNC_I2S2_BCK>,
+ <PINMUX_GPIO27__FUNC_I2S2_LRCK>;
+ drive-strength = <4>;
+ };
+ };
+
+ aud_gpio_i2s3_off: aud-gpio-i2s3-off-pins {
+ pins-sdata {
+ pinmux = <PINMUX_GPIO4__FUNC_GPIO4>;
+ output-low;
+ };
+ };
+
+ aud_gpio_i2s3_on: aud-gpio-i2s3-on-pins {
+ pins-sdata {
+ pinmux = <PINMUX_GPIO4__FUNC_I2S3_DO>;
+ drive-strength = <4>;
+ };
+ };
+
+ aud_gpio_tdm_off: aud-gpio-tdm-off-pins { };
+
+ aud_gpio_tdm_on: aud-gpio-tdm-on-pins { };
+
+ aud_gpio_pcm_off: aud-gpio-pcm-off-pins {
+ pins-clk-sdata {
+ pinmux = <PINMUX_GPIO115__FUNC_GPIO115>,
+ <PINMUX_GPIO116__FUNC_GPIO116>,
+ <PINMUX_GPIO117__FUNC_GPIO117>,
+ <PINMUX_GPIO118__FUNC_GPIO118>;
+ output-low;
+ };
+ };
+
+ aud_gpio_pcm_on: aud-gpio-pcm-on-pins {
+ pins-clk-sdata {
+ pinmux = <PINMUX_GPIO115__FUNC_PCM_CLK>,
+ <PINMUX_GPIO116__FUNC_PCM_SYNC>,
+ <PINMUX_GPIO117__FUNC_PCM_DI>,
+ <PINMUX_GPIO118__FUNC_PCM_DO>;
+ };
+ };
+
+ aud_gpio_dmic_sec: aud-gpio-dmic-sec-pins {
+ pins {
+ pinmux = <PINMUX_GPIO23__FUNC_GPIO23>;
+ output-low;
+ };
+ };
+
+ bt_pins_reset: bt-reset-pins {
+ pins-bt-reset {
+ pinmux = <PINMUX_GPIO155__FUNC_GPIO155>;
+ output-high;
+ };
+ };
+
+ dpi_pins_sleep: dpi-sleep-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO103__FUNC_GPIO103>,
+ <PINMUX_GPIO104__FUNC_GPIO104>,
+ <PINMUX_GPIO105__FUNC_GPIO105>,
+ <PINMUX_GPIO106__FUNC_GPIO106>,
+ <PINMUX_GPIO107__FUNC_GPIO107>,
+ <PINMUX_GPIO108__FUNC_GPIO108>,
+ <PINMUX_GPIO109__FUNC_GPIO109>,
+ <PINMUX_GPIO110__FUNC_GPIO110>,
+ <PINMUX_GPIO111__FUNC_GPIO111>,
+ <PINMUX_GPIO112__FUNC_GPIO112>,
+ <PINMUX_GPIO113__FUNC_GPIO113>,
+ <PINMUX_GPIO114__FUNC_GPIO114>,
+ <PINMUX_GPIO101__FUNC_GPIO101>,
+ <PINMUX_GPIO100__FUNC_GPIO100>,
+ <PINMUX_GPIO102__FUNC_GPIO102>,
+ <PINMUX_GPIO99__FUNC_GPIO99>;
+ drive-strength = <10>;
+ output-low;
+ };
+ };
+
+ dpi_pins_default: dpi-default-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO103__FUNC_DPI_DATA0>,
+ <PINMUX_GPIO104__FUNC_DPI_DATA1>,
+ <PINMUX_GPIO105__FUNC_DPI_DATA2>,
+ <PINMUX_GPIO106__FUNC_DPI_DATA3>,
+ <PINMUX_GPIO107__FUNC_DPI_DATA4>,
+ <PINMUX_GPIO108__FUNC_DPI_DATA5>,
+ <PINMUX_GPIO109__FUNC_DPI_DATA6>,
+ <PINMUX_GPIO110__FUNC_DPI_DATA7>,
+ <PINMUX_GPIO111__FUNC_DPI_DATA8>,
+ <PINMUX_GPIO112__FUNC_DPI_DATA9>,
+ <PINMUX_GPIO113__FUNC_DPI_DATA10>,
+ <PINMUX_GPIO114__FUNC_DPI_DATA11>,
+ <PINMUX_GPIO101__FUNC_DPI_HSYNC>,
+ <PINMUX_GPIO100__FUNC_DPI_VSYNC>,
+ <PINMUX_GPIO102__FUNC_DPI_DE>,
+ <PINMUX_GPIO99__FUNC_DPI_PCLK>;
+ drive-strength = <10>;
+ };
+ };
+
+ ec_ap_int: cros-ec-int-pins {
+ pins-ec-ap-int-odl {
+ pinmux = <PINMUX_GPIO13__FUNC_GPIO13>;
+ input-enable;
+ };
+ };
+
+ edp_panel_fixed_pins: edp-panel-fixed-pins {
+ pins-vreg-en {
+ pinmux = <PINMUX_GPIO153__FUNC_GPIO153>;
+ output-high;
+ };
+ };
+
+ en_pp1800_dpbrdg: en-pp1800-dpbrdg-pins {
+ pins-vreg-en {
+ pinmux = <PINMUX_GPIO39__FUNC_GPIO39>;
+ output-low;
+ };
+ };
+
+ gsc_int: gsc-int-pins {
+ pins-gsc-ap-int-odl {
+ pinmux = <PINMUX_GPIO15__FUNC_GPIO15>;
+ input-enable;
+ };
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO128__FUNC_SDA0>,
+ <PINMUX_GPIO127__FUNC_SCL0>;
+ bias-disable;
+ drive-strength = <4>;
+ input-enable;
+ };
+ };
+
+ i2c1_pins: i2c1-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO130__FUNC_SDA1>,
+ <PINMUX_GPIO129__FUNC_SCL1>;
+ bias-disable;
+ drive-strength = <4>;
+ input-enable;
+ };
+ };
+
+ i2c2_pins: i2c2-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO132__FUNC_SDA2>,
+ <PINMUX_GPIO131__FUNC_SCL2>;
+ bias-disable;
+ drive-strength = <4>;
+ input-enable;
+ };
+ };
+
+ i2c3_pins: i2c3-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO134__FUNC_SDA3>,
+ <PINMUX_GPIO133__FUNC_SCL3>;
+ bias-disable;
+ drive-strength = <4>;
+ input-enable;
+ };
+ };
+
+ i2c5_pins: i2c5-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO138__FUNC_SDA5>,
+ <PINMUX_GPIO137__FUNC_SCL5>;
+ bias-disable;
+ drive-strength = <4>;
+ input-enable;
+ };
+ };
+
+ it6505_pins: it6505-pins {
+ pins-hpd {
+ pinmux = <PINMUX_GPIO10__FUNC_GPIO10>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-int {
+ pinmux = <PINMUX_GPIO8__FUNC_GPIO8>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-reset {
+ pinmux = <PINMUX_GPIO177__FUNC_GPIO177>;
+ output-low;
+ bias-pull-up;
+ };
+ };
+
+ mmc0_pins_default: mmc0-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO68__FUNC_MSDC0_CLK>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO71__FUNC_MSDC0_DAT0>,
+ <PINMUX_GPIO72__FUNC_MSDC0_DAT1>,
+ <PINMUX_GPIO73__FUNC_MSDC0_DAT2>,
+ <PINMUX_GPIO74__FUNC_MSDC0_DAT3>,
+ <PINMUX_GPIO75__FUNC_MSDC0_DAT4>,
+ <PINMUX_GPIO76__FUNC_MSDC0_DAT5>,
+ <PINMUX_GPIO77__FUNC_MSDC0_DAT6>,
+ <PINMUX_GPIO78__FUNC_MSDC0_DAT7>,
+ <PINMUX_GPIO69__FUNC_MSDC0_CMD>;
+ input-enable;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO70__FUNC_MSDC0_RSTB>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc0_pins_uhs: mmc0-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO68__FUNC_MSDC0_CLK>;
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO71__FUNC_MSDC0_DAT0>,
+ <PINMUX_GPIO72__FUNC_MSDC0_DAT1>,
+ <PINMUX_GPIO73__FUNC_MSDC0_DAT2>,
+ <PINMUX_GPIO74__FUNC_MSDC0_DAT3>,
+ <PINMUX_GPIO75__FUNC_MSDC0_DAT4>,
+ <PINMUX_GPIO76__FUNC_MSDC0_DAT5>,
+ <PINMUX_GPIO77__FUNC_MSDC0_DAT6>,
+ <PINMUX_GPIO78__FUNC_MSDC0_DAT7>,
+ <PINMUX_GPIO69__FUNC_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <6>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-ds {
+ pinmux = <PINMUX_GPIO67__FUNC_MSDC0_DSL>;
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO70__FUNC_MSDC0_RSTB>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc1_pins_default: mmc1-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO84__FUNC_MSDC1_CLK>;
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO86__FUNC_MSDC1_DAT0>,
+ <PINMUX_GPIO87__FUNC_MSDC1_DAT1>,
+ <PINMUX_GPIO88__FUNC_MSDC1_DAT2>,
+ <PINMUX_GPIO89__FUNC_MSDC1_DAT3>,
+ <PINMUX_GPIO85__FUNC_MSDC1_CMD>;
+ input-enable;
+ drive-strength = <6>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc1_pins_uhs: mmc1-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO84__FUNC_MSDC1_CLK>;
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO86__FUNC_MSDC1_DAT0>,
+ <PINMUX_GPIO87__FUNC_MSDC1_DAT1>,
+ <PINMUX_GPIO88__FUNC_MSDC1_DAT2>,
+ <PINMUX_GPIO89__FUNC_MSDC1_DAT3>,
+ <PINMUX_GPIO85__FUNC_MSDC1_CMD>;
+ input-enable;
+ drive-strength = <8>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc1_pins_eint: mmc1-eint-pins {
+ pins-dat1 {
+ pinmux = <PINMUX_GPIO87__FUNC_GPIO87>;
+ input-enable;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ nor_pins_default: nor-default-pins {
+ pins-clk-dat {
+ pinmux = <PINMUX_GPIO63__FUNC_SPINOR_IO0>,
+ <PINMUX_GPIO61__FUNC_SPINOR_CK>,
+ <PINMUX_GPIO64__FUNC_SPINOR_IO1>;
+ drive-strength = <6>;
+ bias-pull-down;
+ };
+
+ pins-cs-dat {
+ pinmux = <PINMUX_GPIO62__FUNC_SPINOR_CS>,
+ <PINMUX_GPIO65__FUNC_SPINOR_IO2>,
+ <PINMUX_GPIO66__FUNC_SPINOR_IO3>;
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
+
+ pen_eject: pen-eject-pins {
+ pins {
+ pinmux = <PINMUX_GPIO18__FUNC_GPIO18>;
+ input-enable;
+ /* External pull-up. */
+ bias-disable;
+ };
+ };
+
+ pwm0_pin: disp-pwm-pins {
+ pins {
+ pinmux = <PINMUX_GPIO97__FUNC_DISP_PWM>;
+ output-high;
+ };
+ };
+
+ rt1019p_pins_default: rt1019p-default-pins {
+ pins-sdb {
+ pinmux = <PINMUX_GPIO150__FUNC_GPIO150>;
+ output-low;
+ };
+ };
+
+ scp_pins: scp-default-pins {
+ pins-scp-uart {
+ pinmux = <PINMUX_GPIO48__FUNC_TP_URXD2_AO>,
+ <PINMUX_GPIO49__FUNC_TP_UTXD2_AO>;
+ };
+ };
+
+ spi1_pins: spi1-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO40__FUNC_SPI1_CLK_A>,
+ <PINMUX_GPIO41__FUNC_SPI1_CSB_A>,
+ <PINMUX_GPIO42__FUNC_SPI1_MO_A>,
+ <PINMUX_GPIO43__FUNC_SPI1_MI_A>;
+ bias-disable;
+ input-enable;
+ };
+ };
+
+ spi2_pins: spi2-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO44__FUNC_SPI2_CLK_A>,
+ <PINMUX_GPIO45__FUNC_GPIO45>,
+ <PINMUX_GPIO46__FUNC_SPI2_MO_A>,
+ <PINMUX_GPIO47__FUNC_SPI2_MI_A>;
+ bias-disable;
+ input-enable;
+ };
+ };
+
+ spmi_pins: spmi-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO183__FUNC_SPMI_SCL>,
+ <PINMUX_GPIO184__FUNC_SPMI_SDA>;
+ };
+ };
+
+ touchscreen_pins: touchscreen-pins {
+ pins-irq {
+ pinmux = <PINMUX_GPIO12__FUNC_GPIO12>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-reset {
+ pinmux = <PINMUX_GPIO60__FUNC_GPIO60>;
+ output-high;
+ };
+
+ pins-report-sw {
+ pinmux = <PINMUX_GPIO37__FUNC_GPIO37>;
+ output-low;
+ };
+ };
+
+ trackpad_pin: trackpad-default-pins {
+ pins-int-n {
+ pinmux = <PINMUX_GPIO11__FUNC_GPIO11>;
+ input-enable;
+ bias-disable; /* pulled externally */
+ };
+ };
+
+ wifi_enable_pin: wifi-enable-pins {
+ pins-wifi-enable {
+ pinmux = <PINMUX_GPIO54__FUNC_GPIO54>;
+ };
+ };
+
+ wifi_wakeup_pin: wifi-wakeup-pins {
+ pins-wifi-wakeup {
+ pinmux = <PINMUX_GPIO7__FUNC_GPIO7>;
+ input-enable;
+ };
+ };
+};
+
+&pwm0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pin>;
+ status = "okay";
+};
+
+&pwrap {
+ pmic {
+ compatible = "mediatek,mt6366", "mediatek,mt6358";
+ interrupt-controller;
+ interrupts-extended = <&pio 201 IRQ_TYPE_LEVEL_HIGH>;
+ #interrupt-cells = <2>;
+
+ mt6366codec: codec {
+ compatible = "mediatek,mt6366-sound", "mediatek,mt6358-sound";
+ Avdd-supply = <&mt6366_vaud28_reg>;
+ mediatek,dmic-mode = <1>; /* one-wire */
+ };
+
+ mt6366_regulators: regulators {
+ compatible = "mediatek,mt6366-regulator", "mediatek,mt6358-regulator";
+ vsys-ldo1-supply = <&pp4200_z2>;
+ vsys-ldo2-supply = <&pp4200_z2>;
+ vsys-ldo3-supply = <&pp4200_z2>;
+ vsys-vcore-supply = <&pp4200_z2>;
+ vsys-vdram1-supply = <&pp4200_z2>;
+ vsys-vgpu-supply = <&pp4200_z2>;
+ vsys-vmodem-supply = <&pp4200_z2>;
+ vsys-vpa-supply = <&pp4200_z2>;
+ vsys-vproc11-supply = <&pp4200_z2>;
+ vsys-vproc12-supply = <&pp4200_z2>;
+ vsys-vs1-supply = <&pp4200_z2>;
+ vsys-vs2-supply = <&pp4200_z2>;
+ vs1-ldo1-supply = <&mt6366_vs1_reg>;
+ vs2-ldo1-supply = <&mt6366_vdram1_reg>;
+ vs2-ldo2-supply = <&mt6366_vs2_reg>;
+ vs2-ldo3-supply = <&mt6366_vs2_reg>;
+
+ vcore {
+ regulator-name = "pp0750_dvdd_core";
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <800000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
+ MT6397_BUCK_MODE_FORCE_PWM>;
+ regulator-always-on;
+ };
+
+ mt6366_vdram1_reg: vdram1 {
+ regulator-name = "pp1125_emi_vdd2";
+ regulator-min-microvolt = <1125000>;
+ regulator-max-microvolt = <1125000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <0>;
+ regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
+ MT6397_BUCK_MODE_FORCE_PWM>;
+ regulator-always-on;
+ };
+
+ mt6366_vgpu_reg: vgpu {
+ /*
+ * Called "ppvar_dvdd_gpu" in the schematic.
+ * Called "ppvar_dvdd_vgpu" here to match
+ * regulator coupling requirements.
+ */
+ regulator-name = "ppvar_dvdd_vgpu";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
+ MT6397_BUCK_MODE_FORCE_PWM>;
+ regulator-coupled-with = <&mt6366_vsram_gpu_reg>;
+ regulator-coupled-max-spread = <10000>;
+ };
+
+ mt6366_vproc11_reg: vproc11 {
+ regulator-name = "ppvar_dvdd_proc_bc_mt6366";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
+ MT6397_BUCK_MODE_FORCE_PWM>;
+ regulator-always-on;
+ };
+
+ mt6366_vproc12_reg: vproc12 {
+ regulator-name = "ppvar_dvdd_proc_lc";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <200>;
+ regulator-allowed-modes = <MT6397_BUCK_MODE_AUTO
+ MT6397_BUCK_MODE_FORCE_PWM>;
+ regulator-always-on;
+ };
+
+ mt6366_vs1_reg: vs1 {
+ regulator-name = "pp2000_vs1";
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <0>;
+ regulator-always-on;
+ };
+
+ mt6366_vs2_reg: vs2 {
+ regulator-name = "pp1350_vs2";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-ramp-delay = <12500>;
+ regulator-enable-ramp-delay = <0>;
+ regulator-always-on;
+ };
+
+ va12 {
+ regulator-name = "pp1200_va12";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <270>;
+ regulator-always-on;
+ };
+
+ mt6366_vaud28_reg: vaud28 {
+ regulator-name = "pp2800_vaud28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vaux18_reg: vaux18 {
+ regulator-name = "pp1840_vaux18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1840000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vbif28_reg: vbif28 {
+ regulator-name = "pp2800_vbif28";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vcn18_reg: vcn18 {
+ regulator-name = "pp1800_vcn18_x";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vcn28_reg: vcn28 {
+ regulator-name = "pp2800_vcn28_x";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vefuse_reg: vefuse {
+ regulator-name = "pp1800_vefuse";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vfe28_reg: vfe28 {
+ regulator-name = "pp2800_vfe28_x";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vemc_reg: vemc {
+ regulator-name = "pp3000_vemc";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-enable-ramp-delay = <60>;
+ };
+
+ mt6366_vibr_reg: vibr {
+ regulator-name = "pp2800_vibr_x";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <60>;
+ };
+
+ mt6366_vio18_reg: vio18 {
+ regulator-name = "pp1800_vio18_s3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <2700>;
+ regulator-always-on;
+ };
+
+ mt6366_vio28_reg: vio28 {
+ regulator-name = "pp2800_vio28_x";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ mt6366_vm18_reg: vm18 {
+ regulator-name = "pp1800_emi_vdd1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1840000>;
+ regulator-enable-ramp-delay = <325>;
+ regulator-always-on;
+ };
+
+ mt6366_vmc_reg: vmc {
+ regulator-name = "pp3000_vmc";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-enable-ramp-delay = <60>;
+ };
+
+ mt6366_vmddr_reg: vmddr {
+ regulator-name = "pm0750_emi_vmddr";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <750000>;
+ regulator-enable-ramp-delay = <325>;
+ regulator-always-on;
+ };
+
+ mt6366_vmch_reg: vmch {
+ regulator-name = "pp3000_vmch";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-enable-ramp-delay = <60>;
+ };
+
+ mt6366_vcn33_reg: vcn33 {
+ regulator-name = "pp3300_vcn33_x";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-enable-ramp-delay = <270>;
+ };
+
+ vdram2 {
+ regulator-name = "pp0600_emi_vddq";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <600000>;
+ regulator-enable-ramp-delay = <3300>;
+ regulator-always-on;
+ };
+
+ mt6366_vrf12_reg: vrf12 {
+ regulator-name = "pp1200_vrf12_x";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ mt6366_vrf18_reg: vrf18 {
+ regulator-name = "pp1800_vrf18_x";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-enable-ramp-delay = <120>;
+ };
+
+ vsim1 {
+ regulator-name = "pp1860_vsim1_x";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1860000>;
+ regulator-enable-ramp-delay = <540>;
+ };
+
+ mt6366_vsim2_reg: vsim2 {
+ regulator-name = "pp2760_vsim2_x";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2760000>;
+ regulator-enable-ramp-delay = <540>;
+ };
+
+ mt6366_vsram_gpu_reg: vsram-gpu {
+ regulator-name = "pp0900_dvdd_sram_gpu";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <240>;
+ regulator-coupled-with = <&mt6366_vgpu_reg>;
+ regulator-coupled-max-spread = <10000>;
+ };
+
+ mt6366_vsram_others_reg: vsram-others {
+ regulator-name = "pp0900_dvdd_sram_core";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <240>;
+ regulator-always-on;
+ };
+
+ mt6366_vsram_proc11_reg: vsram-proc11 {
+ regulator-name = "pp0900_dvdd_sram_bc";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <240>;
+ regulator-always-on;
+ };
+
+ mt6366_vsram_proc12_reg: vsram-proc12 {
+ regulator-name = "pp0900_dvdd_sram_lc";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-ramp-delay = <6250>;
+ regulator-enable-ramp-delay = <240>;
+ regulator-always-on;
+ };
+
+ vusb {
+ regulator-name = "pp3070_vusb";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3070000>;
+ regulator-enable-ramp-delay = <270>;
+ regulator-always-on;
+ };
+
+ vxo22 {
+ regulator-name = "pp2240_vxo22";
+ regulator-min-microvolt = <2200000>;
+ regulator-max-microvolt = <2240000>;
+ regulator-enable-ramp-delay = <120>;
+ /* Feeds DCXO internally */
+ regulator-always-on;
+ };
+ };
+
+ rtc {
+ compatible = "mediatek,mt6366-rtc", "mediatek,mt6358-rtc";
+ };
+ };
+};
+
+&scp {
+ pinctrl-names = "default";
+ pinctrl-0 = <&scp_pins>;
+ firmware-name = "mediatek/mt8186/scp.img";
+ memory-region = <&scp_mem>;
+ status = "okay";
+
+ cros-ec-rpmsg {
+ compatible = "google,cros-ec-rpmsg";
+ mediatek,rpmsg-name = "cros-ec-rpmsg";
+ };
+};
+
+&spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ mediatek,pad-select = <0>;
+ status = "okay";
+
+ cros_ec: ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ interrupts-extended = <&pio 13 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_ap_int>;
+
+ i2c_tunnel: i2c-tunnel {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ typec {
+ compatible = "google,cros-ec-typec";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_c0: connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ label = "left";
+ power-role = "dual";
+ data-role = "host";
+ try-power-role = "source";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ typec_port0: endpoint { };
+ };
+ };
+ };
+
+ usb_c1: connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ label = "right";
+ power-role = "dual";
+ data-role = "host";
+ try-power-role = "source";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+
+ typec_port1: endpoint { };
+ };
+ };
+ };
+ };
+ };
+};
+
+&spi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_pins>;
+ cs-gpios = <&pio 45 GPIO_ACTIVE_LOW>;
+ mediatek,pad-select = <0>;
+ status = "okay";
+
+ tpm@0 {
+ compatible = "google,cr50";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&gsc_int>;
+ interrupt-parent = <&pio>;
+ interrupts = <15 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&ssusb0 {
+ status = "okay";
+};
+
+&ssusb1 {
+ status = "okay";
+};
+
+&u3phy0 {
+ status = "okay";
+};
+
+&u3phy1 {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_host0 {
+ vbus-supply = <&pp3300_s3>;
+ status = "okay";
+};
+
+&usb_host1 {
+ vbus-supply = <&usb_p1_vbus>;
+ status = "okay";
+ #address-cells = <2>;
+ #size-cells = <2>;
+};
+
+&watchdog {
+ mediatek,reset-by-toprgu;
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>