arm64: dts: rockchip: rk3399-gru: Fix PCI node addresses
Commit Message
The rk3399-gru PCI node addresses are wrong.
In rk3399-gru-scarlet, the bus number in the address should be 0. This is
because bus number assignment is dynamic and not known up front. For FDT,
the bus number is simply ignored.
In rk3399-gru-chromebook, the addresses are simply invalid. The first
"reg" entry must be the configuration space for the device. The entry
should be all 0s except for device/slot and function numbers. The existing
64-bit memory space (0x83000000) entries are not valid because they must
have the BAR address in the lower byte of the first cell.
Warnings for these are enabled by adding the missing 'device_type = "pci"'
for the root port node.
Signed-off-by: Rob Herring <robh@kernel.org>
---
arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi | 3 +--
arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-dumo.dts | 4 ++--
arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi | 1 +
3 files changed, 4 insertions(+), 4 deletions(-)
Comments
On Thu, 30 Nov 2023 13:18:29 -0600, Rob Herring wrote:
> The rk3399-gru PCI node addresses are wrong.
>
> In rk3399-gru-scarlet, the bus number in the address should be 0. This is
> because bus number assignment is dynamic and not known up front. For FDT,
> the bus number is simply ignored.
>
> In rk3399-gru-chromebook, the addresses are simply invalid. The first
> "reg" entry must be the configuration space for the device. The entry
> should be all 0s except for device/slot and function numbers. The existing
> 64-bit memory space (0x83000000) entries are not valid because they must
> have the BAR address in the lower byte of the first cell.
>
> [...]
Applied, thanks!
[1/1] arm64: dts: rockchip: rk3399-gru: Fix PCI node addresses
commit: c13c823a78b77ea0e5f1f73112d910e259911101
Best regards,
@@ -509,8 +509,7 @@ wacky_spi_audio: spi2@0 {
&pci_rootport {
mvl_wifi: wifi@0,0 {
compatible = "pci1b4b,2b42";
- reg = <0x83010000 0x0 0x00000000 0x0 0x00100000
- 0x83010000 0x0 0x00100000 0x0 0x00100000>;
+ reg = <0x0000 0x0 0x0 0x0 0x0>;
interrupt-parent = <&gpio0>;
interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
@@ -34,8 +34,8 @@ &mipi_panel {
&pci_rootport {
wifi@0,0 {
compatible = "qcom,ath10k";
- reg = <0x00010000 0x0 0x00000000 0x0 0x00000000>,
- <0x03010010 0x0 0x00000000 0x0 0x00200000>;
+ reg = <0x00000000 0x0 0x00000000 0x0 0x00000000>,
+ <0x03000010 0x0 0x00000000 0x0 0x00200000>;
qcom,ath10k-calibration-variant = "GO_DUMO";
};
};
@@ -489,6 +489,7 @@ pci_rootport: pcie@0,0 {
#address-cells = <3>;
#size-cells = <2>;
ranges;
+ device_type = "pci";
};
};