[V5,05/26] mmc: core: Add definitions for SD UHS-II cards

Message ID 20221019110647.11076-6-victor.shih@genesyslogic.com.tw
State New
Headers
Series Add support UHS-II for GL9755 |

Commit Message

Victor Shih Oct. 19, 2022, 11:06 a.m. UTC
  Add UHS-II specific data structures for commands and defines for
registers, as described in Part 1 UHS-II Addendum Version 1.01.

UHS-II related definitions are listed below:
  1. UHS-II card capability: sd_uhs2_caps{}
  2. UHS-II configuration: sd_uhs2_config{}
  3. UHS-II Command structure: uhs2_command{}
  4. UHS-II register I/O address and register field definitions: sd_uhs2.h

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
---

Updates in V5:
 - Added UHS2 interfaces in mmc_host_ops: host.h
 - Added UHS2 VDD2 power supply in mmc_supply: host.h
 - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
 - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
 - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
---
 include/linux/mmc/card.h    |  42 +++++-
 include/linux/mmc/core.h    |  13 ++
 include/linux/mmc/host.h    |  70 +++++++++-
 include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
 4 files changed, 386 insertions(+), 2 deletions(-)
 create mode 100644 include/linux/mmc/sd_uhs2.h
  

Comments

Adrian Hunter Nov. 1, 2022, 5:12 p.m. UTC | #1
On 19/10/22 14:06, Victor Shih wrote:
> Add UHS-II specific data structures for commands and defines for
> registers, as described in Part 1 UHS-II Addendum Version 1.01.
> 
> UHS-II related definitions are listed below:
>   1. UHS-II card capability: sd_uhs2_caps{}
>   2. UHS-II configuration: sd_uhs2_config{}
>   3. UHS-II Command structure: uhs2_command{}
>   4. UHS-II register I/O address and register field definitions: sd_uhs2.h
> 
> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
> Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> ---
> 
> Updates in V5:
>  - Added UHS2 interfaces in mmc_host_ops: host.h
>  - Added UHS2 VDD2 power supply in mmc_supply: host.h
>  - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
>  - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
>  - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
> ---
>  include/linux/mmc/card.h    |  42 +++++-
>  include/linux/mmc/core.h    |  13 ++
>  include/linux/mmc/host.h    |  70 +++++++++-
>  include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
>  4 files changed, 386 insertions(+), 2 deletions(-)
>  create mode 100644 include/linux/mmc/sd_uhs2.h
> 
> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> index 4a42f31b7bb0..d638a2c689cf 100644
> --- a/include/linux/mmc/card.h
> +++ b/include/linux/mmc/card.h
> @@ -190,6 +190,13 @@ struct sd_switch_caps {
>  #define SD_MAX_CURRENT_400	(1 << SD_SET_CURRENT_LIMIT_400)
>  #define SD_MAX_CURRENT_600	(1 << SD_SET_CURRENT_LIMIT_600)
>  #define SD_MAX_CURRENT_800	(1 << SD_SET_CURRENT_LIMIT_800)
> +	unsigned int		sd4_curr_limit;
> +#define SD4_SET_POWER_LIMIT_0_72W	0
> +#define SD4_SET_POWER_LIMIT_1_44W	1
> +#define SD4_SET_POWER_LIMIT_2_16W	2
> +#define SD4_SET_POWER_LIMIT_2_88W	3
> +#define SD4_SET_POWER_LIMIT_1_80W	4
> +#define SD4_SET_POWER_NO_CHANGE		(-1)
>  };
>  
>  struct sd_ext_reg {
> @@ -213,7 +220,35 @@ struct sd_ext_reg {
>  
>  struct sd_uhs2_config {
>  	u32			node_id;
> -	/* TODO: Extend with more register configs. */
> +
> +	u32			dap;
> +	u32			gap;
> +	u32			n_fcu;
> +	u32			maxblk_len;
> +	u8			n_lanes;
> +	u8			dadr_len;
> +	u8			app_type;
> +	u8			phy_minor_rev;
> +	u8			phy_major_rev;
> +	u8			can_hibernate;
> +	u8			n_lss_sync;
> +	u8			n_lss_dir;
> +	u8			link_minor_rev;
> +	u8			link_major_rev;
> +	u8			dev_type;
> +	u8			n_data_gap;
> +
> +	u32			n_fcu_set;
> +	u32			maxblk_len_set;
> +	u8			n_lanes_set;
> +	u8			speed_range_set;
> +	u8			n_lss_sync_set;
> +	u8			n_lss_dir_set;
> +	u8			n_data_gap_set;
> +	u8			pwrctrl_mode_set;
> +	u8			max_retry_set;
> +
> +	u8			cfg_complete;
>  };
>  
>  struct sdio_cccr {
> @@ -323,6 +358,9 @@ struct mmc_card {
>  	struct sd_ext_reg	ext_perf;	/* SD extension reg for PERF */
>  
>  	struct sd_uhs2_config	uhs2_config;	/* SD UHS-II config */
> +	u8			uhs2_state;	/* SD UHS-II states */
> +#define MMC_UHS2_INITIALIZED	BIT(1)
> +#define MMC_UHS2_SPEED_B	BIT(2)
>  
>  	unsigned int		sdio_funcs;	/* number of SDIO functions */
>  	atomic_t		sdio_funcs_probed; /* number of probed SDIO funcs */
> @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
>  #define mmc_card_sdio(c)	((c)->type == MMC_TYPE_SDIO)
>  #define mmc_card_sd_combo(c)	((c)->type == MMC_TYPE_SD_COMBO)
>  
> +#define mmc_card_can_poweroff_notify(c)	((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
> +
>  #endif /* LINUX_MMC_CARD_H */
> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> index 6efec0b9820c..2a0581d87706 100644
> --- a/include/linux/mmc/core.h
> +++ b/include/linux/mmc/core.h
> @@ -23,6 +23,14 @@ enum mmc_blk_status {
>  	MMC_BLK_NEW_REQUEST,
>  };
>  
> +struct uhs2_command {
> +	u16	header;
> +	u16	arg;
> +	__be32	*payload;
> +	u32	payload_len;
> +	u32	packet_len;
> +};
> +
>  struct mmc_command {
>  	u32			opcode;
>  	u32			arg;
> @@ -109,6 +117,11 @@ struct mmc_command {
>  	unsigned int		busy_timeout;	/* busy detect timeout in ms */
>  	struct mmc_data		*data;		/* data segment associated with cmd */
>  	struct mmc_request	*mrq;		/* associated request */
> +
> +	struct uhs2_command	*uhs2_cmd;	/* UHS2 command */
> +	u8			*uhs2_resp;	/* UHS2 native cmd resp */
> +	u8			uhs2_resp_len;	/* UHS2 native cmd resp len */
> +	u8			uhs2_tmode0_flag; /* UHS2 transfer mode flag */
>  };
>  
>  struct mmc_data {
> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> index 895bcf7f80b7..249a9414ad10 100644
> --- a/include/linux/mmc/host.h
> +++ b/include/linux/mmc/host.h
> @@ -16,6 +16,7 @@
>  #include <linux/mmc/pm.h>
>  #include <linux/dma-direction.h>
>  #include <linux/blk-crypto-profile.h>
> +#include <linux/mmc/sd_uhs2.h>
>  
>  struct mmc_ios {
>  	unsigned int	clock;			/* clock rate */
> @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
>  };
>  
>  struct sd_uhs2_caps {
> -	/* TODO: Add UHS-II capabilities for the host. */
> +	u32	dap;
> +	u32	gap;
> +	u32	group_desc;
> +	u32	maxblk_len;
> +	u32	n_fcu;
> +	u8	n_lanes;
> +	u8	addr64;
> +	u8	card_type;
> +	u8	phy_rev;
> +	u8	speed_range;
> +	u8	can_hibernate;
> +	u8	n_lss_sync;
> +	u8	n_lss_dir;
> +	u8	link_rev;
> +	u8	host_type;
> +	u8	n_data_gap;
> +
> +	u32	maxblk_len_set;
> +	u32	n_fcu_set;
> +	u8	n_lanes_set;
> +	u8	n_lss_sync_set;
> +	u8	n_lss_dir_set;
> +	u8	n_data_gap_set;
> +	u8	max_retry_set;
> +};
> +
> +struct sd_uhs2_ios {
> +	bool		is_2L_HD_mode;
> +	bool		is_APP_CMD;
> +	unsigned int	power_delay_ms;		/* waiting for stable power */
> +};
> +
> +enum sd_uhs2_operation {
> +	UHS2_PHY_INIT = 0,
> +	UHS2_SET_CONFIG,
> +	UHS2_ENABLE_INT,
> +	UHS2_DISABLE_INT,
> +	UHS2_ENABLE_CLK,
> +	UHS2_DISABLE_CLK,
> +	UHS2_CHECK_DORMANT,
> +	UHS2_SET_SPEED_B,
> +	UHS2_POST_ATTACH_SD,
>  };
>  
>  struct mmc_host;
> @@ -231,6 +273,20 @@ struct mmc_host_ops {
>  
>  	/* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
>  	int	(*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
> +
> +	/* UHS2 interfaces */
> +	int	(*uhs2_detect_init)(struct mmc_host *host);

Never called?

> +	int	(*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);

Never called?

> +	int (*uhs2_disable_clk)(struct mmc_host *host);

Never called?

> +	int (*uhs2_enable_clk)(struct mmc_host *host);

Never called?

> +
> +	/*
> +	 * The uhs2_control callback is used to execute SD UHS-II specific
> +	 * operations. It's mandatory to implement for hosts that supports the
> +	 * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
> +	 * negative errno in case of a failure or zero for success.
> +	 */
> +	int	(*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
>  };
>  
>  struct mmc_cqe_ops {
> @@ -323,6 +379,7 @@ struct mmc_pwrseq;
>  
>  struct mmc_supply {
>  	struct regulator *vmmc;		/* Card power supply */
> +	struct regulator *vmmc2;	/* UHS2 VDD2 power supply */
>  	struct regulator *vqmmc;	/* Optional Vccq supply */
>  	struct regulator *vqmmc2;	/* Optional supply for phy */
>  };
> @@ -344,10 +401,12 @@ struct mmc_host {
>  	u32			ocr_avail_sdio;	/* SDIO-specific OCR */
>  	u32			ocr_avail_sd;	/* SD-specific OCR */
>  	u32			ocr_avail_mmc;	/* MMC-specific OCR */
> +	u32			ocr_avail_uhs2; /* UHS2-specific OCR */
>  	struct wakeup_source	*ws;		/* Enable consume of uevents */
>  	u32			max_current_330;
>  	u32			max_current_300;
>  	u32			max_current_180;
> +	u32			max_current_180_vdd2; /* UHS2 vdd2 max curt. */
>  
>  #define MMC_VDD_165_195		0x00000080	/* VDD voltage 1.65 - 1.95 */
>  #define MMC_VDD_20_21		0x00000100	/* VDD voltage 2.0 ~ 2.1 */
> @@ -366,6 +425,7 @@ struct mmc_host {
>  #define MMC_VDD_33_34		0x00200000	/* VDD voltage 3.3 ~ 3.4 */
>  #define MMC_VDD_34_35		0x00400000	/* VDD voltage 3.4 ~ 3.5 */
>  #define MMC_VDD_35_36		0x00800000	/* VDD voltage 3.5 ~ 3.6 */
> +#define MMC_VDD2_165_195	0x00000080	/* UHS2 VDD2 1.65 ~ 1.95 */
>  
>  	u32			caps;		/* Host capabilities */
>  
> @@ -443,7 +503,12 @@ struct mmc_host {
>  #endif
>  #define MMC_CAP2_ALT_GPT_TEGRA	(1 << 28)	/* Host with eMMC that has GPT entry at a non-standard location */
>  
> +	int flags;
> +#define MMC_UHS2_SUPPORT	(1 << 0)

MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
Both have the same value, but MMC_UHS2_SUPPORT is for
host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state

Please use the correct flag with the correct variable.

> +#define MMC_UHS2_2L_HD		(1 << 2)

MMC_UHS2_2L_HD does not seem to be used. Is it needed?

> +
>  	struct sd_uhs2_caps	uhs2_caps;	/* Host UHS-II capabilities */
> +	struct sd_uhs2_ios	uhs2_ios;	/* Host UHS-II capabilities */
>  
>  	int			fixed_drv_type;	/* fixed driver type for non-removable media */
>  
> @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
>  int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
>  int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
>  
> +#define mmc_uhs2_2L_HD_mode(h)	((h)->uhs2_ios.is_2L_HD_mode)
> +#define mmc_uhs2_APP_cmd(h)	((h)->uhs2_ios.is_APP_CMD)
> +
>  #endif /* LINUX_MMC_HOST_H */
> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
> new file mode 100644
> index 000000000000..8fcf702cf4a5
> --- /dev/null
> +++ b/include/linux/mmc/sd_uhs2.h
> @@ -0,0 +1,263 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Header file for UHS-II packets, Host Controller registers and I/O
> + * accessors.
> + *
> + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
> + */
> +#ifndef LINUX_MMC_UHS2_H
> +#define LINUX_MMC_UHS2_H
> +
> +/* LINK Layer definition */
> +/*
> + * UHS2 Header:
> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
> + *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
> + *      bit [6:4]  : TYP(Packet Type)
> + *                   000b: CCMD(Control command packet)
> + *                   001b: DCMD(Data command packet)
> + *                   010b: RES(Response packet)
> + *                   011b: DATA(Data payload packet)
> + *                   111b: MSG(Message packet)
> + *                   Others: Reserved
> + *      bit [7]    : NP(Native Packet)
> + *      bit [10:8] : TID(Transaction ID)
> + *      bit [11]   : Reserved
> + *      bit [15:12]: SID(Source ID 0: Node ID of Host)
> + *
> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
> + */
> +/*
> + * UHS2 Argument:
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
> + *      bit [3:0]  : MSB of IOADR
> + *      bit [5:4]  : PLEN(Payload Length)
> + *                   00b: 0 byte
> + *                   01b: 4 bytes
> + *                   10b: 8 bytes
> + *                   11b: 16 bytes
> + *      bit [6]    : Reserved
> + *      bit [7]    : R/W(Read/Write)
> + *                   0: Control read command
> + *                   1: Control write command
> + *      bit [15:8] : LSB of IOADR
> + *
> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> + */
> +#define UHS2_NATIVE_PACKET_POS	7
> +#define UHS2_NATIVE_PACKET	(1 << UHS2_NATIVE_PACKET_POS)
> +
> +#define UHS2_PACKET_TYPE_POS	4
> +#define UHS2_PACKET_TYPE_CCMD	(0 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_DCMD	(1 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_RES	(2 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_DATA	(3 << UHS2_PACKET_TYPE_POS)
> +#define UHS2_PACKET_TYPE_MSG	(7 << UHS2_PACKET_TYPE_POS)
> +
> +#define UHS2_DEST_ID_MASK	0x0F
> +#define UHS2_DEST_ID		0x1
> +
> +#define UHS2_SRC_ID_POS		12
> +#define UHS2_SRC_ID_MASK	0xF000
> +
> +#define UHS2_TRANS_ID_POS	8
> +#define UHS2_TRANS_ID_MASK	0x0700
> +
> +/* UHS2 MSG */
> +#define UHS2_MSG_CTG_POS	5
> +#define UHS2_MSG_CTG_LMSG	0x00
> +#define UHS2_MSG_CTG_INT	0x60
> +#define UHS2_MSG_CTG_AMSG	0x80
> +
> +#define UHS2_MSG_CTG_FCREQ	0x00
> +#define UHS2_MSG_CTG_FCRDY	0x01
> +#define UHS2_MSG_CTG_STAT	0x02
> +
> +#define UHS2_MSG_CODE_POS			8
> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR		0x8
> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR	0x8
> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR		0x1
> +
> +/* TRANS Layer definition */
> +
> +/* Native packets*/
> +#define UHS2_NATIVE_CMD_RW_POS	7
> +#define UHS2_NATIVE_CMD_WRITE	(1 << UHS2_NATIVE_CMD_RW_POS)
> +#define UHS2_NATIVE_CMD_READ	(0 << UHS2_NATIVE_CMD_RW_POS)
> +
> +#define UHS2_NATIVE_CMD_PLEN_POS	4
> +#define UHS2_NATIVE_CMD_PLEN_4B		(1 << UHS2_NATIVE_CMD_PLEN_POS)
> +#define UHS2_NATIVE_CMD_PLEN_8B		(2 << UHS2_NATIVE_CMD_PLEN_POS)
> +#define UHS2_NATIVE_CMD_PLEN_16B	(3 << UHS2_NATIVE_CMD_PLEN_POS)
> +
> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK	0xF00
> +#define UHS2_NATIVE_CCMD_MIOADR_MASK		0x0F
> +
> +#define UHS2_NATIVE_CCMD_LIOADR_POS		8
> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK	0x0FF
> +
> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG	BIT(11)
> +#define UHS2_DEV_INIT_PAYLOAD_LEN		1
> +#define UHS2_DEV_INIT_RESP_LEN			6
> +#define UHS2_DEV_ENUM_PAYLOAD_LEN		1
> +#define UHS2_DEV_ENUM_RESP_LEN			8
> +#define UHS2_CFG_WRITE_PAYLOAD_LEN		2
> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN		4
> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN	5
> +#define UHS2_GO_DORMANT_PAYLOAD_LEN		1
> +
> +/*
> + * UHS2 Argument:
> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
> + *      bit [3:0]  : Reserved
> + *      bit [6:3]  : TMODE(Transfer Mode)
> + *                   bit 3: DAM(Data Access Mode)
> + *                   bit 4: TLUM(TLEN Unit Mode)
> + *                   bit 5: LM(Length Mode)
> + *                   bit 6: DM(Duplex Mode)
> + *      bit [7]    : R/W(Read/Write)
> + *                   0: Control read command
> + *                   1: Control write command
> + *      bit [15:8] : Reserved
> + *
> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> + */
> +#define UHS2_DCMD_DM_POS		6
> +#define UHS2_DCMD_2L_HD_MODE		(1 << UHS2_DCMD_DM_POS)
> +#define UHS2_DCMD_LM_POS		5
> +#define UHS2_DCMD_LM_TLEN_EXIST		(1 << UHS2_DCMD_LM_POS)
> +#define UHS2_DCMD_TLUM_POS		4
> +#define UHS2_DCMD_TLUM_BYTE_MODE	(1 << UHS2_DCMD_TLUM_POS)
> +#define UHS2_NATIVE_DCMD_DAM_POS	3
> +#define UHS2_NATIVE_DCMD_DAM_IO		(1 << UHS2_NATIVE_DCMD_DAM_POS)
> +
> +/*
> + * Per UHS2 spec, DCMD payload should be MSB first. There may be
> + * two types of data be assembled to MSB:
> + * 1. TLEN: Input block size for single read/write and number of blocks
> + * for multiple read/write to calculate TLEN as MSB first per spec.
> + * 2. SD command argument.
> + */
> +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
> +{
> +	u32 ret = 0;
> +
> +	ret = ((input & 0xFF) << 24) |
> +		(((input >> 8) & 0xFF) << 16) |
> +		(((input >> 16) & 0xFF) << 8) |
> +		((input >> 24) & 0xFF);
> +	return cpu_to_be32(ret);
> +}
> +
> +#define UHS2_RES_NACK_POS	7
> +#define UHS2_RES_NACK_MASK	(0x1 << UHS2_RES_NACK_POS)
> +
> +#define UHS2_RES_ECODE_POS	4
> +#define UHS2_RES_ECODE_MASK	0x7
> +#define UHS2_RES_ECODE_COND	1
> +#define UHS2_RES_ECODE_ARG	2
> +#define UHS2_RES_ECODE_GEN	3
> +
> +/* IOADR of device registers */
> +#define UHS2_IOADR_GENERIC_CAPS		0x00
> +#define UHS2_IOADR_PHY_CAPS		0x02
> +#define UHS2_IOADR_LINK_CAPS		0x04
> +#define UHS2_IOADR_RSV_CAPS		0x06
> +#define UHS2_IOADR_GENERIC_SETTINGS	0x08
> +#define UHS2_IOADR_PHY_SETTINGS		0x0A
> +#define UHS2_IOADR_LINK_SETTINGS	0x0C
> +#define UHS2_IOADR_PRESET		0x40
> +
> +/* SD application packets */
> +#define UHS2_SD_CMD_INDEX_POS	8
> +
> +#define UHS2_SD_CMD_APP_POS	14
> +#define UHS2_SD_CMD_APP		(1 << UHS2_SD_CMD_APP_POS)
> +
> +/* UHS-II Device Registers */
> +#define UHS2_DEV_CONFIG_REG	0x000
> +
> +/* General Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_GEN_CAPS	(UHS2_DEV_CONFIG_REG + 0x000)
> +#define UHS2_DEV_CONFIG_N_LANES_POS	8
> +#define UHS2_DEV_CONFIG_N_LANES_MASK	0x3F
> +#define UHS2_DEV_CONFIG_2L_HD_FD	0x1
> +#define UHS2_DEV_CONFIG_2D1U_FD		0x2
> +#define UHS2_DEV_CONFIG_1D2U_FD		0x4
> +#define UHS2_DEV_CONFIG_2D2U_FD		0x8
> +#define UHS2_DEV_CONFIG_DADR_POS	14
> +#define UHS2_DEV_CONFIG_DADR_MASK	0x1
> +#define UHS2_DEV_CONFIG_APP_POS		16
> +#define UHS2_DEV_CONFIG_APP_MASK	0xFF
> +#define UHS2_DEV_CONFIG_APP_SD_MEM	0x1
> +
> +#define UHS2_DEV_CONFIG_GEN_SET			(UHS2_DEV_CONFIG_REG + 0x008)
> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS	8
> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD	0x0
> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD		0x2
> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD		0x3
> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD		0x4
> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE	BIT(31)
> +
> +/* PHY Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_PHY_CAPS	(UHS2_DEV_CONFIG_REG + 0x002)
> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK	0xF
> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS	4
> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK	0x3
> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS	15
> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK	0x1
> +#define UHS2_DEV_CONFIG_PHY_CAPS1	(UHS2_DEV_CONFIG_REG + 0x003)
> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK	0xF
> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS	4
> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK	0xF
> +
> +#define UHS2_DEV_CONFIG_PHY_SET			(UHS2_DEV_CONFIG_REG + 0x00A)
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS	6
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A		0x0
> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B		0x1
> +
> +/* LINK-TRAN Caps and Settings registers */
> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS		(UHS2_DEV_CONFIG_REG + 0x004)
> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK		0xF
> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS		4
> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK		0x3
> +#define UHS2_DEV_CONFIG_N_FCU_POS		8
> +#define UHS2_DEV_CONFIG_N_FCU_MASK		0xFF
> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS		16
> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK		0x7
> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS		20
> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK	0xFFF
> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1		(UHS2_DEV_CONFIG_REG + 0x005)
> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK		0xFF
> +
> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET		(UHS2_DEV_CONFIG_REG + 0x00C)
> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN	0x200
> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS	16
> +
> +/* Preset register */
> +#define UHS2_DEV_CONFIG_PRESET	(UHS2_DEV_CONFIG_REG + 0x040)
> +
> +#define UHS2_DEV_INT_REG	0x100
> +
> +#define UHS2_DEV_STATUS_REG	0x180
> +
> +#define UHS2_DEV_CMD_REG		0x200
> +#define UHS2_DEV_CMD_FULL_RESET		(UHS2_DEV_CMD_REG + 0x000)
> +#define UHS2_DEV_CMD_GO_DORMANT_STATE	(UHS2_DEV_CMD_REG + 0x001)
> +#define UHS2_DEV_CMD_DORMANT_HIBER	BIT(7)
> +#define UHS2_DEV_CMD_DEVICE_INIT	(UHS2_DEV_CMD_REG + 0x002)
> +#define UHS2_DEV_INIT_COMPLETE_FLAG	BIT(11)
> +#define UHS2_DEV_CMD_ENUMERATE		(UHS2_DEV_CMD_REG + 0x003)
> +#define UHS2_DEV_CMD_TRANS_ABORT	(UHS2_DEV_CMD_REG + 0x004)
> +
> +#define UHS2_RCLK_MAX	52000000
> +#define UHS2_RCLK_MIN	26000000
> +
> +struct sd_uhs2_wait_active_state_data {
> +	struct mmc_host *host;
> +	struct mmc_command *cmd;
> +};
> +
> +#endif /* LINUX_MMC_UHS2_H */
  
Victor Shih Nov. 16, 2022, 11:06 a.m. UTC | #2
Hi, Adrian

On Wed, Nov 2, 2022 at 1:12 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
>
> On 19/10/22 14:06, Victor Shih wrote:
> > Add UHS-II specific data structures for commands and defines for
> > registers, as described in Part 1 UHS-II Addendum Version 1.01.
> >
> > UHS-II related definitions are listed below:
> >   1. UHS-II card capability: sd_uhs2_caps{}
> >   2. UHS-II configuration: sd_uhs2_config{}
> >   3. UHS-II Command structure: uhs2_command{}
> >   4. UHS-II register I/O address and register field definitions: sd_uhs2.h
> >
> > Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
> > Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
> > Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> > ---
> >
> > Updates in V5:
> >  - Added UHS2 interfaces in mmc_host_ops: host.h
> >  - Added UHS2 VDD2 power supply in mmc_supply: host.h
> >  - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
> >  - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
> >  - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
> > ---
> >  include/linux/mmc/card.h    |  42 +++++-
> >  include/linux/mmc/core.h    |  13 ++
> >  include/linux/mmc/host.h    |  70 +++++++++-
> >  include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
> >  4 files changed, 386 insertions(+), 2 deletions(-)
> >  create mode 100644 include/linux/mmc/sd_uhs2.h
> >
> > diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> > index 4a42f31b7bb0..d638a2c689cf 100644
> > --- a/include/linux/mmc/card.h
> > +++ b/include/linux/mmc/card.h
> > @@ -190,6 +190,13 @@ struct sd_switch_caps {
> >  #define SD_MAX_CURRENT_400   (1 << SD_SET_CURRENT_LIMIT_400)
> >  #define SD_MAX_CURRENT_600   (1 << SD_SET_CURRENT_LIMIT_600)
> >  #define SD_MAX_CURRENT_800   (1 << SD_SET_CURRENT_LIMIT_800)
> > +     unsigned int            sd4_curr_limit;
> > +#define SD4_SET_POWER_LIMIT_0_72W    0
> > +#define SD4_SET_POWER_LIMIT_1_44W    1
> > +#define SD4_SET_POWER_LIMIT_2_16W    2
> > +#define SD4_SET_POWER_LIMIT_2_88W    3
> > +#define SD4_SET_POWER_LIMIT_1_80W    4
> > +#define SD4_SET_POWER_NO_CHANGE              (-1)
> >  };
> >
> >  struct sd_ext_reg {
> > @@ -213,7 +220,35 @@ struct sd_ext_reg {
> >
> >  struct sd_uhs2_config {
> >       u32                     node_id;
> > -     /* TODO: Extend with more register configs. */
> > +
> > +     u32                     dap;
> > +     u32                     gap;
> > +     u32                     n_fcu;
> > +     u32                     maxblk_len;
> > +     u8                      n_lanes;
> > +     u8                      dadr_len;
> > +     u8                      app_type;
> > +     u8                      phy_minor_rev;
> > +     u8                      phy_major_rev;
> > +     u8                      can_hibernate;
> > +     u8                      n_lss_sync;
> > +     u8                      n_lss_dir;
> > +     u8                      link_minor_rev;
> > +     u8                      link_major_rev;
> > +     u8                      dev_type;
> > +     u8                      n_data_gap;
> > +
> > +     u32                     n_fcu_set;
> > +     u32                     maxblk_len_set;
> > +     u8                      n_lanes_set;
> > +     u8                      speed_range_set;
> > +     u8                      n_lss_sync_set;
> > +     u8                      n_lss_dir_set;
> > +     u8                      n_data_gap_set;
> > +     u8                      pwrctrl_mode_set;
> > +     u8                      max_retry_set;
> > +
> > +     u8                      cfg_complete;
> >  };
> >
> >  struct sdio_cccr {
> > @@ -323,6 +358,9 @@ struct mmc_card {
> >       struct sd_ext_reg       ext_perf;       /* SD extension reg for PERF */
> >
> >       struct sd_uhs2_config   uhs2_config;    /* SD UHS-II config */
> > +     u8                      uhs2_state;     /* SD UHS-II states */
> > +#define MMC_UHS2_INITIALIZED BIT(1)
> > +#define MMC_UHS2_SPEED_B     BIT(2)
> >
> >       unsigned int            sdio_funcs;     /* number of SDIO functions */
> >       atomic_t                sdio_funcs_probed; /* number of probed SDIO funcs */
> > @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
> >  #define mmc_card_sdio(c)     ((c)->type == MMC_TYPE_SDIO)
> >  #define mmc_card_sd_combo(c) ((c)->type == MMC_TYPE_SD_COMBO)
> >
> > +#define mmc_card_can_poweroff_notify(c)      ((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
> > +
> >  #endif /* LINUX_MMC_CARD_H */
> > diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> > index 6efec0b9820c..2a0581d87706 100644
> > --- a/include/linux/mmc/core.h
> > +++ b/include/linux/mmc/core.h
> > @@ -23,6 +23,14 @@ enum mmc_blk_status {
> >       MMC_BLK_NEW_REQUEST,
> >  };
> >
> > +struct uhs2_command {
> > +     u16     header;
> > +     u16     arg;
> > +     __be32  *payload;
> > +     u32     payload_len;
> > +     u32     packet_len;
> > +};
> > +
> >  struct mmc_command {
> >       u32                     opcode;
> >       u32                     arg;
> > @@ -109,6 +117,11 @@ struct mmc_command {
> >       unsigned int            busy_timeout;   /* busy detect timeout in ms */
> >       struct mmc_data         *data;          /* data segment associated with cmd */
> >       struct mmc_request      *mrq;           /* associated request */
> > +
> > +     struct uhs2_command     *uhs2_cmd;      /* UHS2 command */
> > +     u8                      *uhs2_resp;     /* UHS2 native cmd resp */
> > +     u8                      uhs2_resp_len;  /* UHS2 native cmd resp len */
> > +     u8                      uhs2_tmode0_flag; /* UHS2 transfer mode flag */
> >  };
> >
> >  struct mmc_data {
> > diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> > index 895bcf7f80b7..249a9414ad10 100644
> > --- a/include/linux/mmc/host.h
> > +++ b/include/linux/mmc/host.h
> > @@ -16,6 +16,7 @@
> >  #include <linux/mmc/pm.h>
> >  #include <linux/dma-direction.h>
> >  #include <linux/blk-crypto-profile.h>
> > +#include <linux/mmc/sd_uhs2.h>
> >
> >  struct mmc_ios {
> >       unsigned int    clock;                  /* clock rate */
> > @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
> >  };
> >
> >  struct sd_uhs2_caps {
> > -     /* TODO: Add UHS-II capabilities for the host. */
> > +     u32     dap;
> > +     u32     gap;
> > +     u32     group_desc;
> > +     u32     maxblk_len;
> > +     u32     n_fcu;
> > +     u8      n_lanes;
> > +     u8      addr64;
> > +     u8      card_type;
> > +     u8      phy_rev;
> > +     u8      speed_range;
> > +     u8      can_hibernate;
> > +     u8      n_lss_sync;
> > +     u8      n_lss_dir;
> > +     u8      link_rev;
> > +     u8      host_type;
> > +     u8      n_data_gap;
> > +
> > +     u32     maxblk_len_set;
> > +     u32     n_fcu_set;
> > +     u8      n_lanes_set;
> > +     u8      n_lss_sync_set;
> > +     u8      n_lss_dir_set;
> > +     u8      n_data_gap_set;
> > +     u8      max_retry_set;
> > +};
> > +
> > +struct sd_uhs2_ios {
> > +     bool            is_2L_HD_mode;
> > +     bool            is_APP_CMD;
> > +     unsigned int    power_delay_ms;         /* waiting for stable power */
> > +};
> > +
> > +enum sd_uhs2_operation {
> > +     UHS2_PHY_INIT = 0,
> > +     UHS2_SET_CONFIG,
> > +     UHS2_ENABLE_INT,
> > +     UHS2_DISABLE_INT,
> > +     UHS2_ENABLE_CLK,
> > +     UHS2_DISABLE_CLK,
> > +     UHS2_CHECK_DORMANT,
> > +     UHS2_SET_SPEED_B,
> > +     UHS2_POST_ATTACH_SD,
> >  };
> >
> >  struct mmc_host;
> > @@ -231,6 +273,20 @@ struct mmc_host_ops {
> >
> >       /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
> >       int     (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
> > +
> > +     /* UHS2 interfaces */
> > +     int     (*uhs2_detect_init)(struct mmc_host *host);
>
> Never called?

Yes, I will delete it.

>
> > +     int     (*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
>
> Never called?

Yes, I will delete it.

>
> > +     int (*uhs2_disable_clk)(struct mmc_host *host);
>
> Never called?

Yes, I will delete it.

>
> > +     int (*uhs2_enable_clk)(struct mmc_host *host);
>
> Never called?

Yes, I will delete it.

>
> > +
> > +     /*
> > +      * The uhs2_control callback is used to execute SD UHS-II specific
> > +      * operations. It's mandatory to implement for hosts that supports the
> > +      * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
> > +      * negative errno in case of a failure or zero for success.
> > +      */
> > +     int     (*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
> >  };
> >
> >  struct mmc_cqe_ops {
> > @@ -323,6 +379,7 @@ struct mmc_pwrseq;
> >
> >  struct mmc_supply {
> >       struct regulator *vmmc;         /* Card power supply */
> > +     struct regulator *vmmc2;        /* UHS2 VDD2 power supply */
> >       struct regulator *vqmmc;        /* Optional Vccq supply */
> >       struct regulator *vqmmc2;       /* Optional supply for phy */
> >  };
> > @@ -344,10 +401,12 @@ struct mmc_host {
> >       u32                     ocr_avail_sdio; /* SDIO-specific OCR */
> >       u32                     ocr_avail_sd;   /* SD-specific OCR */
> >       u32                     ocr_avail_mmc;  /* MMC-specific OCR */
> > +     u32                     ocr_avail_uhs2; /* UHS2-specific OCR */
> >       struct wakeup_source    *ws;            /* Enable consume of uevents */
> >       u32                     max_current_330;
> >       u32                     max_current_300;
> >       u32                     max_current_180;
> > +     u32                     max_current_180_vdd2; /* UHS2 vdd2 max curt. */
> >
> >  #define MMC_VDD_165_195              0x00000080      /* VDD voltage 1.65 - 1.95 */
> >  #define MMC_VDD_20_21                0x00000100      /* VDD voltage 2.0 ~ 2.1 */
> > @@ -366,6 +425,7 @@ struct mmc_host {
> >  #define MMC_VDD_33_34                0x00200000      /* VDD voltage 3.3 ~ 3.4 */
> >  #define MMC_VDD_34_35                0x00400000      /* VDD voltage 3.4 ~ 3.5 */
> >  #define MMC_VDD_35_36                0x00800000      /* VDD voltage 3.5 ~ 3.6 */
> > +#define MMC_VDD2_165_195     0x00000080      /* UHS2 VDD2 1.65 ~ 1.95 */
> >
> >       u32                     caps;           /* Host capabilities */
> >
> > @@ -443,7 +503,12 @@ struct mmc_host {
> >  #endif
> >  #define MMC_CAP2_ALT_GPT_TEGRA       (1 << 28)       /* Host with eMMC that has GPT entry at a non-standard location */
> >
> > +     int flags;
> > +#define MMC_UHS2_SUPPORT     (1 << 0)
>
> MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
> Both have the same value, but MMC_UHS2_SUPPORT is for
> host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state
>
> Please use the correct flag with the correct variable.
>

The value of MMC_UHS2_SUPPORT is (1<<0) and the value of
MMC_UHS2_INITIALIZED is BIT(1).
Both have different values, therefore I'm not sure what you mean.
May you give me some more advice? Thanks.

> > +#define MMC_UHS2_2L_HD               (1 << 2)
>
> MMC_UHS2_2L_HD does not seem to be used. Is it needed?

I confirmed this, I don't use it, I will delete it.

>
> > +
> >       struct sd_uhs2_caps     uhs2_caps;      /* Host UHS-II capabilities */
> > +     struct sd_uhs2_ios      uhs2_ios;       /* Host UHS-II capabilities */
> >
> >       int                     fixed_drv_type; /* fixed driver type for non-removable media */
> >
> > @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
> >  int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
> >  int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
> >
> > +#define mmc_uhs2_2L_HD_mode(h)       ((h)->uhs2_ios.is_2L_HD_mode)
> > +#define mmc_uhs2_APP_cmd(h)  ((h)->uhs2_ios.is_APP_CMD)
> > +
> >  #endif /* LINUX_MMC_HOST_H */
> > diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
> > new file mode 100644
> > index 000000000000..8fcf702cf4a5
> > --- /dev/null
> > +++ b/include/linux/mmc/sd_uhs2.h
> > @@ -0,0 +1,263 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + * Header file for UHS-II packets, Host Controller registers and I/O
> > + * accessors.
> > + *
> > + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
> > + */
> > +#ifndef LINUX_MMC_UHS2_H
> > +#define LINUX_MMC_UHS2_H
> > +
> > +/* LINK Layer definition */
> > +/*
> > + * UHS2 Header:
> > + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
> > + *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
> > + *      bit [6:4]  : TYP(Packet Type)
> > + *                   000b: CCMD(Control command packet)
> > + *                   001b: DCMD(Data command packet)
> > + *                   010b: RES(Response packet)
> > + *                   011b: DATA(Data payload packet)
> > + *                   111b: MSG(Message packet)
> > + *                   Others: Reserved
> > + *      bit [7]    : NP(Native Packet)
> > + *      bit [10:8] : TID(Transaction ID)
> > + *      bit [11]   : Reserved
> > + *      bit [15:12]: SID(Source ID 0: Node ID of Host)
> > + *
> > + * Broadcast CCMD issued by Host is represented as DID=SID=0.
> > + */
> > +/*
> > + * UHS2 Argument:
> > + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
> > + *      bit [3:0]  : MSB of IOADR
> > + *      bit [5:4]  : PLEN(Payload Length)
> > + *                   00b: 0 byte
> > + *                   01b: 4 bytes
> > + *                   10b: 8 bytes
> > + *                   11b: 16 bytes
> > + *      bit [6]    : Reserved
> > + *      bit [7]    : R/W(Read/Write)
> > + *                   0: Control read command
> > + *                   1: Control write command
> > + *      bit [15:8] : LSB of IOADR
> > + *
> > + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> > + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> > + */
> > +#define UHS2_NATIVE_PACKET_POS       7
> > +#define UHS2_NATIVE_PACKET   (1 << UHS2_NATIVE_PACKET_POS)
> > +
> > +#define UHS2_PACKET_TYPE_POS 4
> > +#define UHS2_PACKET_TYPE_CCMD        (0 << UHS2_PACKET_TYPE_POS)
> > +#define UHS2_PACKET_TYPE_DCMD        (1 << UHS2_PACKET_TYPE_POS)
> > +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
> > +#define UHS2_PACKET_TYPE_DATA        (3 << UHS2_PACKET_TYPE_POS)
> > +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
> > +
> > +#define UHS2_DEST_ID_MASK    0x0F
> > +#define UHS2_DEST_ID         0x1
> > +
> > +#define UHS2_SRC_ID_POS              12
> > +#define UHS2_SRC_ID_MASK     0xF000
> > +
> > +#define UHS2_TRANS_ID_POS    8
> > +#define UHS2_TRANS_ID_MASK   0x0700
> > +
> > +/* UHS2 MSG */
> > +#define UHS2_MSG_CTG_POS     5
> > +#define UHS2_MSG_CTG_LMSG    0x00
> > +#define UHS2_MSG_CTG_INT     0x60
> > +#define UHS2_MSG_CTG_AMSG    0x80
> > +
> > +#define UHS2_MSG_CTG_FCREQ   0x00
> > +#define UHS2_MSG_CTG_FCRDY   0x01
> > +#define UHS2_MSG_CTG_STAT    0x02
> > +
> > +#define UHS2_MSG_CODE_POS                    8
> > +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR               0x8
> > +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR     0x8
> > +#define UHS2_MSG_CODE_STAT_RECOVER_ERR               0x1
> > +
> > +/* TRANS Layer definition */
> > +
> > +/* Native packets*/
> > +#define UHS2_NATIVE_CMD_RW_POS       7
> > +#define UHS2_NATIVE_CMD_WRITE        (1 << UHS2_NATIVE_CMD_RW_POS)
> > +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
> > +
> > +#define UHS2_NATIVE_CMD_PLEN_POS     4
> > +#define UHS2_NATIVE_CMD_PLEN_4B              (1 << UHS2_NATIVE_CMD_PLEN_POS)
> > +#define UHS2_NATIVE_CMD_PLEN_8B              (2 << UHS2_NATIVE_CMD_PLEN_POS)
> > +#define UHS2_NATIVE_CMD_PLEN_16B     (3 << UHS2_NATIVE_CMD_PLEN_POS)
> > +
> > +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK     0xF00
> > +#define UHS2_NATIVE_CCMD_MIOADR_MASK         0x0F
> > +
> > +#define UHS2_NATIVE_CCMD_LIOADR_POS          8
> > +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK     0x0FF
> > +
> > +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG     BIT(11)
> > +#define UHS2_DEV_INIT_PAYLOAD_LEN            1
> > +#define UHS2_DEV_INIT_RESP_LEN                       6
> > +#define UHS2_DEV_ENUM_PAYLOAD_LEN            1
> > +#define UHS2_DEV_ENUM_RESP_LEN                       8
> > +#define UHS2_CFG_WRITE_PAYLOAD_LEN           2
> > +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN              4
> > +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN  5
> > +#define UHS2_GO_DORMANT_PAYLOAD_LEN          1
> > +
> > +/*
> > + * UHS2 Argument:
> > + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
> > + *      bit [3:0]  : Reserved
> > + *      bit [6:3]  : TMODE(Transfer Mode)
> > + *                   bit 3: DAM(Data Access Mode)
> > + *                   bit 4: TLUM(TLEN Unit Mode)
> > + *                   bit 5: LM(Length Mode)
> > + *                   bit 6: DM(Duplex Mode)
> > + *      bit [7]    : R/W(Read/Write)
> > + *                   0: Control read command
> > + *                   1: Control write command
> > + *      bit [15:8] : Reserved
> > + *
> > + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> > + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> > + */
> > +#define UHS2_DCMD_DM_POS             6
> > +#define UHS2_DCMD_2L_HD_MODE         (1 << UHS2_DCMD_DM_POS)
> > +#define UHS2_DCMD_LM_POS             5
> > +#define UHS2_DCMD_LM_TLEN_EXIST              (1 << UHS2_DCMD_LM_POS)
> > +#define UHS2_DCMD_TLUM_POS           4
> > +#define UHS2_DCMD_TLUM_BYTE_MODE     (1 << UHS2_DCMD_TLUM_POS)
> > +#define UHS2_NATIVE_DCMD_DAM_POS     3
> > +#define UHS2_NATIVE_DCMD_DAM_IO              (1 << UHS2_NATIVE_DCMD_DAM_POS)
> > +
> > +/*
> > + * Per UHS2 spec, DCMD payload should be MSB first. There may be
> > + * two types of data be assembled to MSB:
> > + * 1. TLEN: Input block size for single read/write and number of blocks
> > + * for multiple read/write to calculate TLEN as MSB first per spec.
> > + * 2. SD command argument.
> > + */
> > +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
> > +{
> > +     u32 ret = 0;
> > +
> > +     ret = ((input & 0xFF) << 24) |
> > +             (((input >> 8) & 0xFF) << 16) |
> > +             (((input >> 16) & 0xFF) << 8) |
> > +             ((input >> 24) & 0xFF);
> > +     return cpu_to_be32(ret);
> > +}
> > +
> > +#define UHS2_RES_NACK_POS    7
> > +#define UHS2_RES_NACK_MASK   (0x1 << UHS2_RES_NACK_POS)
> > +
> > +#define UHS2_RES_ECODE_POS   4
> > +#define UHS2_RES_ECODE_MASK  0x7
> > +#define UHS2_RES_ECODE_COND  1
> > +#define UHS2_RES_ECODE_ARG   2
> > +#define UHS2_RES_ECODE_GEN   3
> > +
> > +/* IOADR of device registers */
> > +#define UHS2_IOADR_GENERIC_CAPS              0x00
> > +#define UHS2_IOADR_PHY_CAPS          0x02
> > +#define UHS2_IOADR_LINK_CAPS         0x04
> > +#define UHS2_IOADR_RSV_CAPS          0x06
> > +#define UHS2_IOADR_GENERIC_SETTINGS  0x08
> > +#define UHS2_IOADR_PHY_SETTINGS              0x0A
> > +#define UHS2_IOADR_LINK_SETTINGS     0x0C
> > +#define UHS2_IOADR_PRESET            0x40
> > +
> > +/* SD application packets */
> > +#define UHS2_SD_CMD_INDEX_POS        8
> > +
> > +#define UHS2_SD_CMD_APP_POS  14
> > +#define UHS2_SD_CMD_APP              (1 << UHS2_SD_CMD_APP_POS)
> > +
> > +/* UHS-II Device Registers */
> > +#define UHS2_DEV_CONFIG_REG  0x000
> > +
> > +/* General Caps and Settings registers */
> > +#define UHS2_DEV_CONFIG_GEN_CAPS     (UHS2_DEV_CONFIG_REG + 0x000)
> > +#define UHS2_DEV_CONFIG_N_LANES_POS  8
> > +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
> > +#define UHS2_DEV_CONFIG_2L_HD_FD     0x1
> > +#define UHS2_DEV_CONFIG_2D1U_FD              0x2
> > +#define UHS2_DEV_CONFIG_1D2U_FD              0x4
> > +#define UHS2_DEV_CONFIG_2D2U_FD              0x8
> > +#define UHS2_DEV_CONFIG_DADR_POS     14
> > +#define UHS2_DEV_CONFIG_DADR_MASK    0x1
> > +#define UHS2_DEV_CONFIG_APP_POS              16
> > +#define UHS2_DEV_CONFIG_APP_MASK     0xFF
> > +#define UHS2_DEV_CONFIG_APP_SD_MEM   0x1
> > +
> > +#define UHS2_DEV_CONFIG_GEN_SET                      (UHS2_DEV_CONFIG_REG + 0x008)
> > +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS  8
> > +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD     0x0
> > +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD              0x2
> > +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD              0x3
> > +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD              0x4
> > +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
> > +
> > +/* PHY Caps and Settings registers */
> > +#define UHS2_DEV_CONFIG_PHY_CAPS     (UHS2_DEV_CONFIG_REG + 0x002)
> > +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK       0xF
> > +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS        4
> > +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK       0x3
> > +#define UHS2_DEV_CONFIG_CAN_HIBER_POS        15
> > +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK       0x1
> > +#define UHS2_DEV_CONFIG_PHY_CAPS1    (UHS2_DEV_CONFIG_REG + 0x003)
> > +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK       0xF
> > +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS        4
> > +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK       0xF
> > +
> > +#define UHS2_DEV_CONFIG_PHY_SET                      (UHS2_DEV_CONFIG_REG + 0x00A)
> > +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS    6
> > +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A              0x0
> > +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B              0x1
> > +
> > +/* LINK-TRAN Caps and Settings registers */
> > +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS               (UHS2_DEV_CONFIG_REG + 0x004)
> > +#define UHS2_DEV_CONFIG_LT_MINOR_MASK                0xF
> > +#define UHS2_DEV_CONFIG_LT_MAJOR_POS         4
> > +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK                0x3
> > +#define UHS2_DEV_CONFIG_N_FCU_POS            8
> > +#define UHS2_DEV_CONFIG_N_FCU_MASK           0xFF
> > +#define UHS2_DEV_CONFIG_DEV_TYPE_POS         16
> > +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK                0x7
> > +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS              20
> > +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK     0xFFF
> > +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1              (UHS2_DEV_CONFIG_REG + 0x005)
> > +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK              0xFF
> > +
> > +#define UHS2_DEV_CONFIG_LINK_TRAN_SET                (UHS2_DEV_CONFIG_REG + 0x00C)
> > +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN   0x200
> > +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
> > +
> > +/* Preset register */
> > +#define UHS2_DEV_CONFIG_PRESET       (UHS2_DEV_CONFIG_REG + 0x040)
> > +
> > +#define UHS2_DEV_INT_REG     0x100
> > +
> > +#define UHS2_DEV_STATUS_REG  0x180
> > +
> > +#define UHS2_DEV_CMD_REG             0x200
> > +#define UHS2_DEV_CMD_FULL_RESET              (UHS2_DEV_CMD_REG + 0x000)
> > +#define UHS2_DEV_CMD_GO_DORMANT_STATE        (UHS2_DEV_CMD_REG + 0x001)
> > +#define UHS2_DEV_CMD_DORMANT_HIBER   BIT(7)
> > +#define UHS2_DEV_CMD_DEVICE_INIT     (UHS2_DEV_CMD_REG + 0x002)
> > +#define UHS2_DEV_INIT_COMPLETE_FLAG  BIT(11)
> > +#define UHS2_DEV_CMD_ENUMERATE               (UHS2_DEV_CMD_REG + 0x003)
> > +#define UHS2_DEV_CMD_TRANS_ABORT     (UHS2_DEV_CMD_REG + 0x004)
> > +
> > +#define UHS2_RCLK_MAX        52000000
> > +#define UHS2_RCLK_MIN        26000000
> > +
> > +struct sd_uhs2_wait_active_state_data {
> > +     struct mmc_host *host;
> > +     struct mmc_command *cmd;
> > +};
> > +
> > +#endif /* LINUX_MMC_UHS2_H */
>

Thanks, Victor Shih
  
Adrian Hunter Nov. 16, 2022, 1:48 p.m. UTC | #3
On 16/11/22 13:06, Victor Shih wrote:
> Hi, Adrian
> 
> On Wed, Nov 2, 2022 at 1:12 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
>>
>> On 19/10/22 14:06, Victor Shih wrote:
>>> Add UHS-II specific data structures for commands and defines for
>>> registers, as described in Part 1 UHS-II Addendum Version 1.01.
>>>
>>> UHS-II related definitions are listed below:
>>>   1. UHS-II card capability: sd_uhs2_caps{}
>>>   2. UHS-II configuration: sd_uhs2_config{}
>>>   3. UHS-II Command structure: uhs2_command{}
>>>   4. UHS-II register I/O address and register field definitions: sd_uhs2.h
>>>
>>> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
>>> Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
>>> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
>>> ---
>>>
>>> Updates in V5:
>>>  - Added UHS2 interfaces in mmc_host_ops: host.h
>>>  - Added UHS2 VDD2 power supply in mmc_supply: host.h
>>>  - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
>>>  - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
>>>  - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
>>> ---
>>>  include/linux/mmc/card.h    |  42 +++++-
>>>  include/linux/mmc/core.h    |  13 ++
>>>  include/linux/mmc/host.h    |  70 +++++++++-
>>>  include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
>>>  4 files changed, 386 insertions(+), 2 deletions(-)
>>>  create mode 100644 include/linux/mmc/sd_uhs2.h
>>>
>>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
>>> index 4a42f31b7bb0..d638a2c689cf 100644
>>> --- a/include/linux/mmc/card.h
>>> +++ b/include/linux/mmc/card.h
>>> @@ -190,6 +190,13 @@ struct sd_switch_caps {
>>>  #define SD_MAX_CURRENT_400   (1 << SD_SET_CURRENT_LIMIT_400)
>>>  #define SD_MAX_CURRENT_600   (1 << SD_SET_CURRENT_LIMIT_600)
>>>  #define SD_MAX_CURRENT_800   (1 << SD_SET_CURRENT_LIMIT_800)
>>> +     unsigned int            sd4_curr_limit;
>>> +#define SD4_SET_POWER_LIMIT_0_72W    0
>>> +#define SD4_SET_POWER_LIMIT_1_44W    1
>>> +#define SD4_SET_POWER_LIMIT_2_16W    2
>>> +#define SD4_SET_POWER_LIMIT_2_88W    3
>>> +#define SD4_SET_POWER_LIMIT_1_80W    4
>>> +#define SD4_SET_POWER_NO_CHANGE              (-1)
>>>  };
>>>
>>>  struct sd_ext_reg {
>>> @@ -213,7 +220,35 @@ struct sd_ext_reg {
>>>
>>>  struct sd_uhs2_config {
>>>       u32                     node_id;
>>> -     /* TODO: Extend with more register configs. */
>>> +
>>> +     u32                     dap;
>>> +     u32                     gap;
>>> +     u32                     n_fcu;
>>> +     u32                     maxblk_len;
>>> +     u8                      n_lanes;
>>> +     u8                      dadr_len;
>>> +     u8                      app_type;
>>> +     u8                      phy_minor_rev;
>>> +     u8                      phy_major_rev;
>>> +     u8                      can_hibernate;
>>> +     u8                      n_lss_sync;
>>> +     u8                      n_lss_dir;
>>> +     u8                      link_minor_rev;
>>> +     u8                      link_major_rev;
>>> +     u8                      dev_type;
>>> +     u8                      n_data_gap;
>>> +
>>> +     u32                     n_fcu_set;
>>> +     u32                     maxblk_len_set;
>>> +     u8                      n_lanes_set;
>>> +     u8                      speed_range_set;
>>> +     u8                      n_lss_sync_set;
>>> +     u8                      n_lss_dir_set;
>>> +     u8                      n_data_gap_set;
>>> +     u8                      pwrctrl_mode_set;
>>> +     u8                      max_retry_set;
>>> +
>>> +     u8                      cfg_complete;
>>>  };
>>>
>>>  struct sdio_cccr {
>>> @@ -323,6 +358,9 @@ struct mmc_card {
>>>       struct sd_ext_reg       ext_perf;       /* SD extension reg for PERF */
>>>
>>>       struct sd_uhs2_config   uhs2_config;    /* SD UHS-II config */
>>> +     u8                      uhs2_state;     /* SD UHS-II states */
>>> +#define MMC_UHS2_INITIALIZED BIT(1)
>>> +#define MMC_UHS2_SPEED_B     BIT(2)
>>>
>>>       unsigned int            sdio_funcs;     /* number of SDIO functions */
>>>       atomic_t                sdio_funcs_probed; /* number of probed SDIO funcs */
>>> @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
>>>  #define mmc_card_sdio(c)     ((c)->type == MMC_TYPE_SDIO)
>>>  #define mmc_card_sd_combo(c) ((c)->type == MMC_TYPE_SD_COMBO)
>>>
>>> +#define mmc_card_can_poweroff_notify(c)      ((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
>>> +
>>>  #endif /* LINUX_MMC_CARD_H */
>>> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
>>> index 6efec0b9820c..2a0581d87706 100644
>>> --- a/include/linux/mmc/core.h
>>> +++ b/include/linux/mmc/core.h
>>> @@ -23,6 +23,14 @@ enum mmc_blk_status {
>>>       MMC_BLK_NEW_REQUEST,
>>>  };
>>>
>>> +struct uhs2_command {
>>> +     u16     header;
>>> +     u16     arg;
>>> +     __be32  *payload;
>>> +     u32     payload_len;
>>> +     u32     packet_len;
>>> +};
>>> +
>>>  struct mmc_command {
>>>       u32                     opcode;
>>>       u32                     arg;
>>> @@ -109,6 +117,11 @@ struct mmc_command {
>>>       unsigned int            busy_timeout;   /* busy detect timeout in ms */
>>>       struct mmc_data         *data;          /* data segment associated with cmd */
>>>       struct mmc_request      *mrq;           /* associated request */
>>> +
>>> +     struct uhs2_command     *uhs2_cmd;      /* UHS2 command */
>>> +     u8                      *uhs2_resp;     /* UHS2 native cmd resp */
>>> +     u8                      uhs2_resp_len;  /* UHS2 native cmd resp len */
>>> +     u8                      uhs2_tmode0_flag; /* UHS2 transfer mode flag */
>>>  };
>>>
>>>  struct mmc_data {
>>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
>>> index 895bcf7f80b7..249a9414ad10 100644
>>> --- a/include/linux/mmc/host.h
>>> +++ b/include/linux/mmc/host.h
>>> @@ -16,6 +16,7 @@
>>>  #include <linux/mmc/pm.h>
>>>  #include <linux/dma-direction.h>
>>>  #include <linux/blk-crypto-profile.h>
>>> +#include <linux/mmc/sd_uhs2.h>
>>>
>>>  struct mmc_ios {
>>>       unsigned int    clock;                  /* clock rate */
>>> @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
>>>  };
>>>
>>>  struct sd_uhs2_caps {
>>> -     /* TODO: Add UHS-II capabilities for the host. */
>>> +     u32     dap;
>>> +     u32     gap;
>>> +     u32     group_desc;
>>> +     u32     maxblk_len;
>>> +     u32     n_fcu;
>>> +     u8      n_lanes;
>>> +     u8      addr64;
>>> +     u8      card_type;
>>> +     u8      phy_rev;
>>> +     u8      speed_range;
>>> +     u8      can_hibernate;
>>> +     u8      n_lss_sync;
>>> +     u8      n_lss_dir;
>>> +     u8      link_rev;
>>> +     u8      host_type;
>>> +     u8      n_data_gap;
>>> +
>>> +     u32     maxblk_len_set;
>>> +     u32     n_fcu_set;
>>> +     u8      n_lanes_set;
>>> +     u8      n_lss_sync_set;
>>> +     u8      n_lss_dir_set;
>>> +     u8      n_data_gap_set;
>>> +     u8      max_retry_set;
>>> +};
>>> +
>>> +struct sd_uhs2_ios {
>>> +     bool            is_2L_HD_mode;
>>> +     bool            is_APP_CMD;
>>> +     unsigned int    power_delay_ms;         /* waiting for stable power */
>>> +};
>>> +
>>> +enum sd_uhs2_operation {
>>> +     UHS2_PHY_INIT = 0,
>>> +     UHS2_SET_CONFIG,
>>> +     UHS2_ENABLE_INT,
>>> +     UHS2_DISABLE_INT,
>>> +     UHS2_ENABLE_CLK,
>>> +     UHS2_DISABLE_CLK,
>>> +     UHS2_CHECK_DORMANT,
>>> +     UHS2_SET_SPEED_B,
>>> +     UHS2_POST_ATTACH_SD,
>>>  };
>>>
>>>  struct mmc_host;
>>> @@ -231,6 +273,20 @@ struct mmc_host_ops {
>>>
>>>       /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
>>>       int     (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
>>> +
>>> +     /* UHS2 interfaces */
>>> +     int     (*uhs2_detect_init)(struct mmc_host *host);
>>
>> Never called?
> 
> Yes, I will delete it.
> 
>>
>>> +     int     (*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
>>
>> Never called?
> 
> Yes, I will delete it.
> 
>>
>>> +     int (*uhs2_disable_clk)(struct mmc_host *host);
>>
>> Never called?
> 
> Yes, I will delete it.
> 
>>
>>> +     int (*uhs2_enable_clk)(struct mmc_host *host);
>>
>> Never called?
> 
> Yes, I will delete it.
> 
>>
>>> +
>>> +     /*
>>> +      * The uhs2_control callback is used to execute SD UHS-II specific
>>> +      * operations. It's mandatory to implement for hosts that supports the
>>> +      * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
>>> +      * negative errno in case of a failure or zero for success.
>>> +      */
>>> +     int     (*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
>>>  };
>>>
>>>  struct mmc_cqe_ops {
>>> @@ -323,6 +379,7 @@ struct mmc_pwrseq;
>>>
>>>  struct mmc_supply {
>>>       struct regulator *vmmc;         /* Card power supply */
>>> +     struct regulator *vmmc2;        /* UHS2 VDD2 power supply */
>>>       struct regulator *vqmmc;        /* Optional Vccq supply */
>>>       struct regulator *vqmmc2;       /* Optional supply for phy */
>>>  };
>>> @@ -344,10 +401,12 @@ struct mmc_host {
>>>       u32                     ocr_avail_sdio; /* SDIO-specific OCR */
>>>       u32                     ocr_avail_sd;   /* SD-specific OCR */
>>>       u32                     ocr_avail_mmc;  /* MMC-specific OCR */
>>> +     u32                     ocr_avail_uhs2; /* UHS2-specific OCR */
>>>       struct wakeup_source    *ws;            /* Enable consume of uevents */
>>>       u32                     max_current_330;
>>>       u32                     max_current_300;
>>>       u32                     max_current_180;
>>> +     u32                     max_current_180_vdd2; /* UHS2 vdd2 max curt. */
>>>
>>>  #define MMC_VDD_165_195              0x00000080      /* VDD voltage 1.65 - 1.95 */
>>>  #define MMC_VDD_20_21                0x00000100      /* VDD voltage 2.0 ~ 2.1 */
>>> @@ -366,6 +425,7 @@ struct mmc_host {
>>>  #define MMC_VDD_33_34                0x00200000      /* VDD voltage 3.3 ~ 3.4 */
>>>  #define MMC_VDD_34_35                0x00400000      /* VDD voltage 3.4 ~ 3.5 */
>>>  #define MMC_VDD_35_36                0x00800000      /* VDD voltage 3.5 ~ 3.6 */
>>> +#define MMC_VDD2_165_195     0x00000080      /* UHS2 VDD2 1.65 ~ 1.95 */
>>>
>>>       u32                     caps;           /* Host capabilities */
>>>
>>> @@ -443,7 +503,12 @@ struct mmc_host {
>>>  #endif
>>>  #define MMC_CAP2_ALT_GPT_TEGRA       (1 << 28)       /* Host with eMMC that has GPT entry at a non-standard location */
>>>
>>> +     int flags;
>>> +#define MMC_UHS2_SUPPORT     (1 << 0)
>>
>> MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
>> Both have the same value, but MMC_UHS2_SUPPORT is for
>> host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state
>>
>> Please use the correct flag with the correct variable.
>>
> 
> The value of MMC_UHS2_SUPPORT is (1<<0) and the value of
> MMC_UHS2_INITIALIZED is BIT(1).
> Both have different values, therefore I'm not sure what you mean.
> May you give me some more advice? Thanks.

I guess I got confused about the values, however it is not OK to
use MMC_UHS2_INITIALIZED for both mmc->flags and card->uhs2_state.
Please make a separate define with a different name for mmc->flags
version of MMC_UHS2_INITIALIZED.

Also, I am confused about the purpose of mmc->flags and
card->uhs2_state.

A host is UHS-II capable as represented by MMC_CAP2_SD_UHS2.
To initialize and use a UHS-II card in UHS-II mode, the host
must be in UHS-II mode.
To initialize and use a UHS-II card in SD mode, the host
must be in SD mode.
So the state of the card and host is always the same:
either UHS-II or not.  Note, that is a consequence of the
hardware I/F.  Whether SD I/F or UHS-II I/F is used is
decided before sending any UHS-II commands. SD I/F is
disabled during UHS-II PHY initialization, whereas
UHS-II I/F is disabled before execution of ACMD41 is
completed.

So it seems like there would only be a need for one flag
to indicate UHS-II mode?

> 
>>> +#define MMC_UHS2_2L_HD               (1 << 2)
>>
>> MMC_UHS2_2L_HD does not seem to be used. Is it needed?
> 
> I confirmed this, I don't use it, I will delete it.
> 
>>
>>> +
>>>       struct sd_uhs2_caps     uhs2_caps;      /* Host UHS-II capabilities */
>>> +     struct sd_uhs2_ios      uhs2_ios;       /* Host UHS-II capabilities */
>>>
>>>       int                     fixed_drv_type; /* fixed driver type for non-removable media */
>>>
>>> @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
>>>  int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
>>>  int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
>>>
>>> +#define mmc_uhs2_2L_HD_mode(h)       ((h)->uhs2_ios.is_2L_HD_mode)
>>> +#define mmc_uhs2_APP_cmd(h)  ((h)->uhs2_ios.is_APP_CMD)
>>> +
>>>  #endif /* LINUX_MMC_HOST_H */
>>> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
>>> new file mode 100644
>>> index 000000000000..8fcf702cf4a5
>>> --- /dev/null
>>> +++ b/include/linux/mmc/sd_uhs2.h
>>> @@ -0,0 +1,263 @@
>>> +/* SPDX-License-Identifier: GPL-2.0-or-later */
>>> +/*
>>> + * Header file for UHS-II packets, Host Controller registers and I/O
>>> + * accessors.
>>> + *
>>> + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
>>> + */
>>> +#ifndef LINUX_MMC_UHS2_H
>>> +#define LINUX_MMC_UHS2_H
>>> +
>>> +/* LINK Layer definition */
>>> +/*
>>> + * UHS2 Header:
>>> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
>>> + *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
>>> + *      bit [6:4]  : TYP(Packet Type)
>>> + *                   000b: CCMD(Control command packet)
>>> + *                   001b: DCMD(Data command packet)
>>> + *                   010b: RES(Response packet)
>>> + *                   011b: DATA(Data payload packet)
>>> + *                   111b: MSG(Message packet)
>>> + *                   Others: Reserved
>>> + *      bit [7]    : NP(Native Packet)
>>> + *      bit [10:8] : TID(Transaction ID)
>>> + *      bit [11]   : Reserved
>>> + *      bit [15:12]: SID(Source ID 0: Node ID of Host)
>>> + *
>>> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
>>> + */
>>> +/*
>>> + * UHS2 Argument:
>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
>>> + *      bit [3:0]  : MSB of IOADR
>>> + *      bit [5:4]  : PLEN(Payload Length)
>>> + *                   00b: 0 byte
>>> + *                   01b: 4 bytes
>>> + *                   10b: 8 bytes
>>> + *                   11b: 16 bytes
>>> + *      bit [6]    : Reserved
>>> + *      bit [7]    : R/W(Read/Write)
>>> + *                   0: Control read command
>>> + *                   1: Control write command
>>> + *      bit [15:8] : LSB of IOADR
>>> + *
>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
>>> + */
>>> +#define UHS2_NATIVE_PACKET_POS       7
>>> +#define UHS2_NATIVE_PACKET   (1 << UHS2_NATIVE_PACKET_POS)
>>> +
>>> +#define UHS2_PACKET_TYPE_POS 4
>>> +#define UHS2_PACKET_TYPE_CCMD        (0 << UHS2_PACKET_TYPE_POS)
>>> +#define UHS2_PACKET_TYPE_DCMD        (1 << UHS2_PACKET_TYPE_POS)
>>> +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
>>> +#define UHS2_PACKET_TYPE_DATA        (3 << UHS2_PACKET_TYPE_POS)
>>> +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
>>> +
>>> +#define UHS2_DEST_ID_MASK    0x0F
>>> +#define UHS2_DEST_ID         0x1
>>> +
>>> +#define UHS2_SRC_ID_POS              12
>>> +#define UHS2_SRC_ID_MASK     0xF000
>>> +
>>> +#define UHS2_TRANS_ID_POS    8
>>> +#define UHS2_TRANS_ID_MASK   0x0700
>>> +
>>> +/* UHS2 MSG */
>>> +#define UHS2_MSG_CTG_POS     5
>>> +#define UHS2_MSG_CTG_LMSG    0x00
>>> +#define UHS2_MSG_CTG_INT     0x60
>>> +#define UHS2_MSG_CTG_AMSG    0x80
>>> +
>>> +#define UHS2_MSG_CTG_FCREQ   0x00
>>> +#define UHS2_MSG_CTG_FCRDY   0x01
>>> +#define UHS2_MSG_CTG_STAT    0x02
>>> +
>>> +#define UHS2_MSG_CODE_POS                    8
>>> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR               0x8
>>> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR     0x8
>>> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR               0x1
>>> +
>>> +/* TRANS Layer definition */
>>> +
>>> +/* Native packets*/
>>> +#define UHS2_NATIVE_CMD_RW_POS       7
>>> +#define UHS2_NATIVE_CMD_WRITE        (1 << UHS2_NATIVE_CMD_RW_POS)
>>> +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
>>> +
>>> +#define UHS2_NATIVE_CMD_PLEN_POS     4
>>> +#define UHS2_NATIVE_CMD_PLEN_4B              (1 << UHS2_NATIVE_CMD_PLEN_POS)
>>> +#define UHS2_NATIVE_CMD_PLEN_8B              (2 << UHS2_NATIVE_CMD_PLEN_POS)
>>> +#define UHS2_NATIVE_CMD_PLEN_16B     (3 << UHS2_NATIVE_CMD_PLEN_POS)
>>> +
>>> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK     0xF00
>>> +#define UHS2_NATIVE_CCMD_MIOADR_MASK         0x0F
>>> +
>>> +#define UHS2_NATIVE_CCMD_LIOADR_POS          8
>>> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK     0x0FF
>>> +
>>> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG     BIT(11)
>>> +#define UHS2_DEV_INIT_PAYLOAD_LEN            1
>>> +#define UHS2_DEV_INIT_RESP_LEN                       6
>>> +#define UHS2_DEV_ENUM_PAYLOAD_LEN            1
>>> +#define UHS2_DEV_ENUM_RESP_LEN                       8
>>> +#define UHS2_CFG_WRITE_PAYLOAD_LEN           2
>>> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN              4
>>> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN  5
>>> +#define UHS2_GO_DORMANT_PAYLOAD_LEN          1
>>> +
>>> +/*
>>> + * UHS2 Argument:
>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
>>> + *      bit [3:0]  : Reserved
>>> + *      bit [6:3]  : TMODE(Transfer Mode)
>>> + *                   bit 3: DAM(Data Access Mode)
>>> + *                   bit 4: TLUM(TLEN Unit Mode)
>>> + *                   bit 5: LM(Length Mode)
>>> + *                   bit 6: DM(Duplex Mode)
>>> + *      bit [7]    : R/W(Read/Write)
>>> + *                   0: Control read command
>>> + *                   1: Control write command
>>> + *      bit [15:8] : Reserved
>>> + *
>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
>>> + */
>>> +#define UHS2_DCMD_DM_POS             6
>>> +#define UHS2_DCMD_2L_HD_MODE         (1 << UHS2_DCMD_DM_POS)
>>> +#define UHS2_DCMD_LM_POS             5
>>> +#define UHS2_DCMD_LM_TLEN_EXIST              (1 << UHS2_DCMD_LM_POS)
>>> +#define UHS2_DCMD_TLUM_POS           4
>>> +#define UHS2_DCMD_TLUM_BYTE_MODE     (1 << UHS2_DCMD_TLUM_POS)
>>> +#define UHS2_NATIVE_DCMD_DAM_POS     3
>>> +#define UHS2_NATIVE_DCMD_DAM_IO              (1 << UHS2_NATIVE_DCMD_DAM_POS)
>>> +
>>> +/*
>>> + * Per UHS2 spec, DCMD payload should be MSB first. There may be
>>> + * two types of data be assembled to MSB:
>>> + * 1. TLEN: Input block size for single read/write and number of blocks
>>> + * for multiple read/write to calculate TLEN as MSB first per spec.
>>> + * 2. SD command argument.
>>> + */
>>> +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
>>> +{
>>> +     u32 ret = 0;
>>> +
>>> +     ret = ((input & 0xFF) << 24) |
>>> +             (((input >> 8) & 0xFF) << 16) |
>>> +             (((input >> 16) & 0xFF) << 8) |
>>> +             ((input >> 24) & 0xFF);
>>> +     return cpu_to_be32(ret);
>>> +}
>>> +
>>> +#define UHS2_RES_NACK_POS    7
>>> +#define UHS2_RES_NACK_MASK   (0x1 << UHS2_RES_NACK_POS)
>>> +
>>> +#define UHS2_RES_ECODE_POS   4
>>> +#define UHS2_RES_ECODE_MASK  0x7
>>> +#define UHS2_RES_ECODE_COND  1
>>> +#define UHS2_RES_ECODE_ARG   2
>>> +#define UHS2_RES_ECODE_GEN   3
>>> +
>>> +/* IOADR of device registers */
>>> +#define UHS2_IOADR_GENERIC_CAPS              0x00
>>> +#define UHS2_IOADR_PHY_CAPS          0x02
>>> +#define UHS2_IOADR_LINK_CAPS         0x04
>>> +#define UHS2_IOADR_RSV_CAPS          0x06
>>> +#define UHS2_IOADR_GENERIC_SETTINGS  0x08
>>> +#define UHS2_IOADR_PHY_SETTINGS              0x0A
>>> +#define UHS2_IOADR_LINK_SETTINGS     0x0C
>>> +#define UHS2_IOADR_PRESET            0x40
>>> +
>>> +/* SD application packets */
>>> +#define UHS2_SD_CMD_INDEX_POS        8
>>> +
>>> +#define UHS2_SD_CMD_APP_POS  14
>>> +#define UHS2_SD_CMD_APP              (1 << UHS2_SD_CMD_APP_POS)
>>> +
>>> +/* UHS-II Device Registers */
>>> +#define UHS2_DEV_CONFIG_REG  0x000
>>> +
>>> +/* General Caps and Settings registers */
>>> +#define UHS2_DEV_CONFIG_GEN_CAPS     (UHS2_DEV_CONFIG_REG + 0x000)
>>> +#define UHS2_DEV_CONFIG_N_LANES_POS  8
>>> +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
>>> +#define UHS2_DEV_CONFIG_2L_HD_FD     0x1
>>> +#define UHS2_DEV_CONFIG_2D1U_FD              0x2
>>> +#define UHS2_DEV_CONFIG_1D2U_FD              0x4
>>> +#define UHS2_DEV_CONFIG_2D2U_FD              0x8
>>> +#define UHS2_DEV_CONFIG_DADR_POS     14
>>> +#define UHS2_DEV_CONFIG_DADR_MASK    0x1
>>> +#define UHS2_DEV_CONFIG_APP_POS              16
>>> +#define UHS2_DEV_CONFIG_APP_MASK     0xFF
>>> +#define UHS2_DEV_CONFIG_APP_SD_MEM   0x1
>>> +
>>> +#define UHS2_DEV_CONFIG_GEN_SET                      (UHS2_DEV_CONFIG_REG + 0x008)
>>> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS  8
>>> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD     0x0
>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD              0x2
>>> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD              0x3
>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD              0x4
>>> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
>>> +
>>> +/* PHY Caps and Settings registers */
>>> +#define UHS2_DEV_CONFIG_PHY_CAPS     (UHS2_DEV_CONFIG_REG + 0x002)
>>> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK       0xF
>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS        4
>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK       0x3
>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS        15
>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK       0x1
>>> +#define UHS2_DEV_CONFIG_PHY_CAPS1    (UHS2_DEV_CONFIG_REG + 0x003)
>>> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK       0xF
>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS        4
>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK       0xF
>>> +
>>> +#define UHS2_DEV_CONFIG_PHY_SET                      (UHS2_DEV_CONFIG_REG + 0x00A)
>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS    6
>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A              0x0
>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B              0x1
>>> +
>>> +/* LINK-TRAN Caps and Settings registers */
>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS               (UHS2_DEV_CONFIG_REG + 0x004)
>>> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK                0xF
>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS         4
>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK                0x3
>>> +#define UHS2_DEV_CONFIG_N_FCU_POS            8
>>> +#define UHS2_DEV_CONFIG_N_FCU_MASK           0xFF
>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS         16
>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK                0x7
>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS              20
>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK     0xFFF
>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1              (UHS2_DEV_CONFIG_REG + 0x005)
>>> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK              0xFF
>>> +
>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET                (UHS2_DEV_CONFIG_REG + 0x00C)
>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN   0x200
>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
>>> +
>>> +/* Preset register */
>>> +#define UHS2_DEV_CONFIG_PRESET       (UHS2_DEV_CONFIG_REG + 0x040)
>>> +
>>> +#define UHS2_DEV_INT_REG     0x100
>>> +
>>> +#define UHS2_DEV_STATUS_REG  0x180
>>> +
>>> +#define UHS2_DEV_CMD_REG             0x200
>>> +#define UHS2_DEV_CMD_FULL_RESET              (UHS2_DEV_CMD_REG + 0x000)
>>> +#define UHS2_DEV_CMD_GO_DORMANT_STATE        (UHS2_DEV_CMD_REG + 0x001)
>>> +#define UHS2_DEV_CMD_DORMANT_HIBER   BIT(7)
>>> +#define UHS2_DEV_CMD_DEVICE_INIT     (UHS2_DEV_CMD_REG + 0x002)
>>> +#define UHS2_DEV_INIT_COMPLETE_FLAG  BIT(11)
>>> +#define UHS2_DEV_CMD_ENUMERATE               (UHS2_DEV_CMD_REG + 0x003)
>>> +#define UHS2_DEV_CMD_TRANS_ABORT     (UHS2_DEV_CMD_REG + 0x004)
>>> +
>>> +#define UHS2_RCLK_MAX        52000000
>>> +#define UHS2_RCLK_MIN        26000000
>>> +
>>> +struct sd_uhs2_wait_active_state_data {
>>> +     struct mmc_host *host;
>>> +     struct mmc_command *cmd;
>>> +};
>>> +
>>> +#endif /* LINUX_MMC_UHS2_H */
>>
> 
> Thanks, Victor Shih
  
Ben Chuang Nov. 17, 2022, 6:19 a.m. UTC | #4
Hi,

On Wed, Nov 16, 2022 at 9:48 PM Adrian Hunter <adrian.hunter@intel.com> wrote:
>
> On 16/11/22 13:06, Victor Shih wrote:
> > Hi, Adrian
> >
> > On Wed, Nov 2, 2022 at 1:12 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
> >>
> >> On 19/10/22 14:06, Victor Shih wrote:
> >>> Add UHS-II specific data structures for commands and defines for
> >>> registers, as described in Part 1 UHS-II Addendum Version 1.01.
> >>>
> >>> UHS-II related definitions are listed below:
> >>>   1. UHS-II card capability: sd_uhs2_caps{}
> >>>   2. UHS-II configuration: sd_uhs2_config{}
> >>>   3. UHS-II Command structure: uhs2_command{}
> >>>   4. UHS-II register I/O address and register field definitions: sd_uhs2.h
> >>>
> >>> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
> >>> Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
> >>> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> >>> ---
> >>>
> >>> Updates in V5:
> >>>  - Added UHS2 interfaces in mmc_host_ops: host.h
> >>>  - Added UHS2 VDD2 power supply in mmc_supply: host.h
> >>>  - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
> >>>  - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
> >>>  - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
> >>> ---
> >>>  include/linux/mmc/card.h    |  42 +++++-
> >>>  include/linux/mmc/core.h    |  13 ++
> >>>  include/linux/mmc/host.h    |  70 +++++++++-
> >>>  include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
> >>>  4 files changed, 386 insertions(+), 2 deletions(-)
> >>>  create mode 100644 include/linux/mmc/sd_uhs2.h
> >>>
> >>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> >>> index 4a42f31b7bb0..d638a2c689cf 100644
> >>> --- a/include/linux/mmc/card.h
> >>> +++ b/include/linux/mmc/card.h
> >>> @@ -190,6 +190,13 @@ struct sd_switch_caps {
> >>>  #define SD_MAX_CURRENT_400   (1 << SD_SET_CURRENT_LIMIT_400)
> >>>  #define SD_MAX_CURRENT_600   (1 << SD_SET_CURRENT_LIMIT_600)
> >>>  #define SD_MAX_CURRENT_800   (1 << SD_SET_CURRENT_LIMIT_800)
> >>> +     unsigned int            sd4_curr_limit;
> >>> +#define SD4_SET_POWER_LIMIT_0_72W    0
> >>> +#define SD4_SET_POWER_LIMIT_1_44W    1
> >>> +#define SD4_SET_POWER_LIMIT_2_16W    2
> >>> +#define SD4_SET_POWER_LIMIT_2_88W    3
> >>> +#define SD4_SET_POWER_LIMIT_1_80W    4
> >>> +#define SD4_SET_POWER_NO_CHANGE              (-1)
> >>>  };
> >>>
> >>>  struct sd_ext_reg {
> >>> @@ -213,7 +220,35 @@ struct sd_ext_reg {
> >>>
> >>>  struct sd_uhs2_config {
> >>>       u32                     node_id;
> >>> -     /* TODO: Extend with more register configs. */
> >>> +
> >>> +     u32                     dap;
> >>> +     u32                     gap;
> >>> +     u32                     n_fcu;
> >>> +     u32                     maxblk_len;
> >>> +     u8                      n_lanes;
> >>> +     u8                      dadr_len;
> >>> +     u8                      app_type;
> >>> +     u8                      phy_minor_rev;
> >>> +     u8                      phy_major_rev;
> >>> +     u8                      can_hibernate;
> >>> +     u8                      n_lss_sync;
> >>> +     u8                      n_lss_dir;
> >>> +     u8                      link_minor_rev;
> >>> +     u8                      link_major_rev;
> >>> +     u8                      dev_type;
> >>> +     u8                      n_data_gap;
> >>> +
> >>> +     u32                     n_fcu_set;
> >>> +     u32                     maxblk_len_set;
> >>> +     u8                      n_lanes_set;
> >>> +     u8                      speed_range_set;
> >>> +     u8                      n_lss_sync_set;
> >>> +     u8                      n_lss_dir_set;
> >>> +     u8                      n_data_gap_set;
> >>> +     u8                      pwrctrl_mode_set;
> >>> +     u8                      max_retry_set;
> >>> +
> >>> +     u8                      cfg_complete;
> >>>  };
> >>>
> >>>  struct sdio_cccr {
> >>> @@ -323,6 +358,9 @@ struct mmc_card {
> >>>       struct sd_ext_reg       ext_perf;       /* SD extension reg for PERF */
> >>>
> >>>       struct sd_uhs2_config   uhs2_config;    /* SD UHS-II config */
> >>> +     u8                      uhs2_state;     /* SD UHS-II states */
> >>> +#define MMC_UHS2_INITIALIZED BIT(1)
> >>> +#define MMC_UHS2_SPEED_B     BIT(2)
> >>>
> >>>       unsigned int            sdio_funcs;     /* number of SDIO functions */
> >>>       atomic_t                sdio_funcs_probed; /* number of probed SDIO funcs */
> >>> @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
> >>>  #define mmc_card_sdio(c)     ((c)->type == MMC_TYPE_SDIO)
> >>>  #define mmc_card_sd_combo(c) ((c)->type == MMC_TYPE_SD_COMBO)
> >>>
> >>> +#define mmc_card_can_poweroff_notify(c)      ((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
> >>> +
> >>>  #endif /* LINUX_MMC_CARD_H */
> >>> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> >>> index 6efec0b9820c..2a0581d87706 100644
> >>> --- a/include/linux/mmc/core.h
> >>> +++ b/include/linux/mmc/core.h
> >>> @@ -23,6 +23,14 @@ enum mmc_blk_status {
> >>>       MMC_BLK_NEW_REQUEST,
> >>>  };
> >>>
> >>> +struct uhs2_command {
> >>> +     u16     header;
> >>> +     u16     arg;
> >>> +     __be32  *payload;
> >>> +     u32     payload_len;
> >>> +     u32     packet_len;
> >>> +};
> >>> +
> >>>  struct mmc_command {
> >>>       u32                     opcode;
> >>>       u32                     arg;
> >>> @@ -109,6 +117,11 @@ struct mmc_command {
> >>>       unsigned int            busy_timeout;   /* busy detect timeout in ms */
> >>>       struct mmc_data         *data;          /* data segment associated with cmd */
> >>>       struct mmc_request      *mrq;           /* associated request */
> >>> +
> >>> +     struct uhs2_command     *uhs2_cmd;      /* UHS2 command */
> >>> +     u8                      *uhs2_resp;     /* UHS2 native cmd resp */
> >>> +     u8                      uhs2_resp_len;  /* UHS2 native cmd resp len */
> >>> +     u8                      uhs2_tmode0_flag; /* UHS2 transfer mode flag */
> >>>  };
> >>>
> >>>  struct mmc_data {
> >>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> >>> index 895bcf7f80b7..249a9414ad10 100644
> >>> --- a/include/linux/mmc/host.h
> >>> +++ b/include/linux/mmc/host.h
> >>> @@ -16,6 +16,7 @@
> >>>  #include <linux/mmc/pm.h>
> >>>  #include <linux/dma-direction.h>
> >>>  #include <linux/blk-crypto-profile.h>
> >>> +#include <linux/mmc/sd_uhs2.h>
> >>>
> >>>  struct mmc_ios {
> >>>       unsigned int    clock;                  /* clock rate */
> >>> @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
> >>>  };
> >>>
> >>>  struct sd_uhs2_caps {
> >>> -     /* TODO: Add UHS-II capabilities for the host. */
> >>> +     u32     dap;
> >>> +     u32     gap;
> >>> +     u32     group_desc;
> >>> +     u32     maxblk_len;
> >>> +     u32     n_fcu;
> >>> +     u8      n_lanes;
> >>> +     u8      addr64;
> >>> +     u8      card_type;
> >>> +     u8      phy_rev;
> >>> +     u8      speed_range;
> >>> +     u8      can_hibernate;
> >>> +     u8      n_lss_sync;
> >>> +     u8      n_lss_dir;
> >>> +     u8      link_rev;
> >>> +     u8      host_type;
> >>> +     u8      n_data_gap;
> >>> +
> >>> +     u32     maxblk_len_set;
> >>> +     u32     n_fcu_set;
> >>> +     u8      n_lanes_set;
> >>> +     u8      n_lss_sync_set;
> >>> +     u8      n_lss_dir_set;
> >>> +     u8      n_data_gap_set;
> >>> +     u8      max_retry_set;
> >>> +};
> >>> +
> >>> +struct sd_uhs2_ios {
> >>> +     bool            is_2L_HD_mode;
> >>> +     bool            is_APP_CMD;
> >>> +     unsigned int    power_delay_ms;         /* waiting for stable power */
> >>> +};
> >>> +
> >>> +enum sd_uhs2_operation {
> >>> +     UHS2_PHY_INIT = 0,
> >>> +     UHS2_SET_CONFIG,
> >>> +     UHS2_ENABLE_INT,
> >>> +     UHS2_DISABLE_INT,
> >>> +     UHS2_ENABLE_CLK,
> >>> +     UHS2_DISABLE_CLK,
> >>> +     UHS2_CHECK_DORMANT,
> >>> +     UHS2_SET_SPEED_B,
> >>> +     UHS2_POST_ATTACH_SD,
> >>>  };
> >>>
> >>>  struct mmc_host;
> >>> @@ -231,6 +273,20 @@ struct mmc_host_ops {
> >>>
> >>>       /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
> >>>       int     (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
> >>> +
> >>> +     /* UHS2 interfaces */
> >>> +     int     (*uhs2_detect_init)(struct mmc_host *host);
> >>
> >> Never called?
> >
> > Yes, I will delete it.
> >
> >>
> >>> +     int     (*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
> >>
> >> Never called?
> >
> > Yes, I will delete it.
> >
> >>
> >>> +     int (*uhs2_disable_clk)(struct mmc_host *host);
> >>
> >> Never called?
> >
> > Yes, I will delete it.
> >
> >>
> >>> +     int (*uhs2_enable_clk)(struct mmc_host *host);
> >>
> >> Never called?
> >
> > Yes, I will delete it.
> >
> >>
> >>> +
> >>> +     /*
> >>> +      * The uhs2_control callback is used to execute SD UHS-II specific
> >>> +      * operations. It's mandatory to implement for hosts that supports the
> >>> +      * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
> >>> +      * negative errno in case of a failure or zero for success.
> >>> +      */
> >>> +     int     (*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
> >>>  };
> >>>
> >>>  struct mmc_cqe_ops {
> >>> @@ -323,6 +379,7 @@ struct mmc_pwrseq;
> >>>
> >>>  struct mmc_supply {
> >>>       struct regulator *vmmc;         /* Card power supply */
> >>> +     struct regulator *vmmc2;        /* UHS2 VDD2 power supply */
> >>>       struct regulator *vqmmc;        /* Optional Vccq supply */
> >>>       struct regulator *vqmmc2;       /* Optional supply for phy */
> >>>  };
> >>> @@ -344,10 +401,12 @@ struct mmc_host {
> >>>       u32                     ocr_avail_sdio; /* SDIO-specific OCR */
> >>>       u32                     ocr_avail_sd;   /* SD-specific OCR */
> >>>       u32                     ocr_avail_mmc;  /* MMC-specific OCR */
> >>> +     u32                     ocr_avail_uhs2; /* UHS2-specific OCR */
> >>>       struct wakeup_source    *ws;            /* Enable consume of uevents */
> >>>       u32                     max_current_330;
> >>>       u32                     max_current_300;
> >>>       u32                     max_current_180;
> >>> +     u32                     max_current_180_vdd2; /* UHS2 vdd2 max curt. */
> >>>
> >>>  #define MMC_VDD_165_195              0x00000080      /* VDD voltage 1.65 - 1.95 */
> >>>  #define MMC_VDD_20_21                0x00000100      /* VDD voltage 2.0 ~ 2.1 */
> >>> @@ -366,6 +425,7 @@ struct mmc_host {
> >>>  #define MMC_VDD_33_34                0x00200000      /* VDD voltage 3.3 ~ 3.4 */
> >>>  #define MMC_VDD_34_35                0x00400000      /* VDD voltage 3.4 ~ 3.5 */
> >>>  #define MMC_VDD_35_36                0x00800000      /* VDD voltage 3.5 ~ 3.6 */
> >>> +#define MMC_VDD2_165_195     0x00000080      /* UHS2 VDD2 1.65 ~ 1.95 */
> >>>
> >>>       u32                     caps;           /* Host capabilities */
> >>>
> >>> @@ -443,7 +503,12 @@ struct mmc_host {
> >>>  #endif
> >>>  #define MMC_CAP2_ALT_GPT_TEGRA       (1 << 28)       /* Host with eMMC that has GPT entry at a non-standard location */
> >>>
> >>> +     int flags;
> >>> +#define MMC_UHS2_SUPPORT     (1 << 0)
> >>
> >> MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
> >> Both have the same value, but MMC_UHS2_SUPPORT is for
> >> host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state
> >>
> >> Please use the correct flag with the correct variable.
> >>
> >
> > The value of MMC_UHS2_SUPPORT is (1<<0) and the value of
> > MMC_UHS2_INITIALIZED is BIT(1).
> > Both have different values, therefore I'm not sure what you mean.
> > May you give me some more advice? Thanks.
>
> I guess I got confused about the values, however it is not OK to
> use MMC_UHS2_INITIALIZED for both mmc->flags and card->uhs2_state.
> Please make a separate define with a different name for mmc->flags
> version of MMC_UHS2_INITIALIZED.

MMC_UHS2_INITIALIZED here is used to judge that the UHS-II I/F has been
initialized and can run in SD-TRAN. In this state,  some SD commands
require a distinction. For example, ACMD (CMD55) should be set by the APP
field in UHS-II packet.

>
> Also, I am confused about the purpose of mmc->flags and
> card->uhs2_state.

It looks like the mmc->flags and card->uhs2_state have the same purpose.
I think it is having trouble with card == NULL in mmc_app_cmd(*host, *card)
in patch [V5, 06/26] so just add one more mmc->flags.
Can wait for confirmation from Victor.

>
> A host is UHS-II capable as represented by MMC_CAP2_SD_UHS2.
> To initialize and use a UHS-II card in UHS-II mode, the host
> must be in UHS-II mode.
> To initialize and use a UHS-II card in SD mode, the host
> must be in SD mode.
> So the state of the card and host is always the same:
> either UHS-II or not.  Note, that is a consequence of the
> hardware I/F.  Whether SD I/F or UHS-II I/F is used is
> decided before sending any UHS-II commands. SD I/F is
> disabled during UHS-II PHY initialization, whereas
> UHS-II I/F is disabled before execution of ACMD41 is
> completed.
>
> So it seems like there would only be a need for one flag
> to indicate UHS-II mode?
>
> >
> >>> +#define MMC_UHS2_2L_HD               (1 << 2)
> >>
> >> MMC_UHS2_2L_HD does not seem to be used. Is it needed?
> >
> > I confirmed this, I don't use it, I will delete it.
> >
> >>
> >>> +
> >>>       struct sd_uhs2_caps     uhs2_caps;      /* Host UHS-II capabilities */
> >>> +     struct sd_uhs2_ios      uhs2_ios;       /* Host UHS-II capabilities */
> >>>
> >>>       int                     fixed_drv_type; /* fixed driver type for non-removable media */
> >>>
> >>> @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
> >>>  int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
> >>>  int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
> >>>
> >>> +#define mmc_uhs2_2L_HD_mode(h)       ((h)->uhs2_ios.is_2L_HD_mode)
> >>> +#define mmc_uhs2_APP_cmd(h)  ((h)->uhs2_ios.is_APP_CMD)
> >>> +
> >>>  #endif /* LINUX_MMC_HOST_H */
> >>> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
> >>> new file mode 100644
> >>> index 000000000000..8fcf702cf4a5
> >>> --- /dev/null
> >>> +++ b/include/linux/mmc/sd_uhs2.h
> >>> @@ -0,0 +1,263 @@
> >>> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> >>> +/*
> >>> + * Header file for UHS-II packets, Host Controller registers and I/O
> >>> + * accessors.
> >>> + *
> >>> + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
> >>> + */
> >>> +#ifndef LINUX_MMC_UHS2_H
> >>> +#define LINUX_MMC_UHS2_H
> >>> +
> >>> +/* LINK Layer definition */
> >>> +/*
> >>> + * UHS2 Header:
> >>> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
> >>> + *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
> >>> + *      bit [6:4]  : TYP(Packet Type)
> >>> + *                   000b: CCMD(Control command packet)
> >>> + *                   001b: DCMD(Data command packet)
> >>> + *                   010b: RES(Response packet)
> >>> + *                   011b: DATA(Data payload packet)
> >>> + *                   111b: MSG(Message packet)
> >>> + *                   Others: Reserved
> >>> + *      bit [7]    : NP(Native Packet)
> >>> + *      bit [10:8] : TID(Transaction ID)
> >>> + *      bit [11]   : Reserved
> >>> + *      bit [15:12]: SID(Source ID 0: Node ID of Host)
> >>> + *
> >>> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
> >>> + */
> >>> +/*
> >>> + * UHS2 Argument:
> >>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
> >>> + *      bit [3:0]  : MSB of IOADR
> >>> + *      bit [5:4]  : PLEN(Payload Length)
> >>> + *                   00b: 0 byte
> >>> + *                   01b: 4 bytes
> >>> + *                   10b: 8 bytes
> >>> + *                   11b: 16 bytes
> >>> + *      bit [6]    : Reserved
> >>> + *      bit [7]    : R/W(Read/Write)
> >>> + *                   0: Control read command
> >>> + *                   1: Control write command
> >>> + *      bit [15:8] : LSB of IOADR
> >>> + *
> >>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> >>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> >>> + */
> >>> +#define UHS2_NATIVE_PACKET_POS       7
> >>> +#define UHS2_NATIVE_PACKET   (1 << UHS2_NATIVE_PACKET_POS)
> >>> +
> >>> +#define UHS2_PACKET_TYPE_POS 4
> >>> +#define UHS2_PACKET_TYPE_CCMD        (0 << UHS2_PACKET_TYPE_POS)
> >>> +#define UHS2_PACKET_TYPE_DCMD        (1 << UHS2_PACKET_TYPE_POS)
> >>> +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
> >>> +#define UHS2_PACKET_TYPE_DATA        (3 << UHS2_PACKET_TYPE_POS)
> >>> +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
> >>> +
> >>> +#define UHS2_DEST_ID_MASK    0x0F
> >>> +#define UHS2_DEST_ID         0x1
> >>> +
> >>> +#define UHS2_SRC_ID_POS              12
> >>> +#define UHS2_SRC_ID_MASK     0xF000
> >>> +
> >>> +#define UHS2_TRANS_ID_POS    8
> >>> +#define UHS2_TRANS_ID_MASK   0x0700
> >>> +
> >>> +/* UHS2 MSG */
> >>> +#define UHS2_MSG_CTG_POS     5
> >>> +#define UHS2_MSG_CTG_LMSG    0x00
> >>> +#define UHS2_MSG_CTG_INT     0x60
> >>> +#define UHS2_MSG_CTG_AMSG    0x80
> >>> +
> >>> +#define UHS2_MSG_CTG_FCREQ   0x00
> >>> +#define UHS2_MSG_CTG_FCRDY   0x01
> >>> +#define UHS2_MSG_CTG_STAT    0x02
> >>> +
> >>> +#define UHS2_MSG_CODE_POS                    8
> >>> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR               0x8
> >>> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR     0x8
> >>> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR               0x1
> >>> +
> >>> +/* TRANS Layer definition */
> >>> +
> >>> +/* Native packets*/
> >>> +#define UHS2_NATIVE_CMD_RW_POS       7
> >>> +#define UHS2_NATIVE_CMD_WRITE        (1 << UHS2_NATIVE_CMD_RW_POS)
> >>> +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
> >>> +
> >>> +#define UHS2_NATIVE_CMD_PLEN_POS     4
> >>> +#define UHS2_NATIVE_CMD_PLEN_4B              (1 << UHS2_NATIVE_CMD_PLEN_POS)
> >>> +#define UHS2_NATIVE_CMD_PLEN_8B              (2 << UHS2_NATIVE_CMD_PLEN_POS)
> >>> +#define UHS2_NATIVE_CMD_PLEN_16B     (3 << UHS2_NATIVE_CMD_PLEN_POS)
> >>> +
> >>> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK     0xF00
> >>> +#define UHS2_NATIVE_CCMD_MIOADR_MASK         0x0F
> >>> +
> >>> +#define UHS2_NATIVE_CCMD_LIOADR_POS          8
> >>> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK     0x0FF
> >>> +
> >>> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG     BIT(11)
> >>> +#define UHS2_DEV_INIT_PAYLOAD_LEN            1
> >>> +#define UHS2_DEV_INIT_RESP_LEN                       6
> >>> +#define UHS2_DEV_ENUM_PAYLOAD_LEN            1
> >>> +#define UHS2_DEV_ENUM_RESP_LEN                       8
> >>> +#define UHS2_CFG_WRITE_PAYLOAD_LEN           2
> >>> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN              4
> >>> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN  5
> >>> +#define UHS2_GO_DORMANT_PAYLOAD_LEN          1
> >>> +
> >>> +/*
> >>> + * UHS2 Argument:
> >>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
> >>> + *      bit [3:0]  : Reserved
> >>> + *      bit [6:3]  : TMODE(Transfer Mode)
> >>> + *                   bit 3: DAM(Data Access Mode)
> >>> + *                   bit 4: TLUM(TLEN Unit Mode)
> >>> + *                   bit 5: LM(Length Mode)
> >>> + *                   bit 6: DM(Duplex Mode)
> >>> + *      bit [7]    : R/W(Read/Write)
> >>> + *                   0: Control read command
> >>> + *                   1: Control write command
> >>> + *      bit [15:8] : Reserved
> >>> + *
> >>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> >>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> >>> + */
> >>> +#define UHS2_DCMD_DM_POS             6
> >>> +#define UHS2_DCMD_2L_HD_MODE         (1 << UHS2_DCMD_DM_POS)
> >>> +#define UHS2_DCMD_LM_POS             5
> >>> +#define UHS2_DCMD_LM_TLEN_EXIST              (1 << UHS2_DCMD_LM_POS)
> >>> +#define UHS2_DCMD_TLUM_POS           4
> >>> +#define UHS2_DCMD_TLUM_BYTE_MODE     (1 << UHS2_DCMD_TLUM_POS)
> >>> +#define UHS2_NATIVE_DCMD_DAM_POS     3
> >>> +#define UHS2_NATIVE_DCMD_DAM_IO              (1 << UHS2_NATIVE_DCMD_DAM_POS)
> >>> +
> >>> +/*
> >>> + * Per UHS2 spec, DCMD payload should be MSB first. There may be
> >>> + * two types of data be assembled to MSB:
> >>> + * 1. TLEN: Input block size for single read/write and number of blocks
> >>> + * for multiple read/write to calculate TLEN as MSB first per spec.
> >>> + * 2. SD command argument.
> >>> + */
> >>> +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
> >>> +{
> >>> +     u32 ret = 0;
> >>> +
> >>> +     ret = ((input & 0xFF) << 24) |
> >>> +             (((input >> 8) & 0xFF) << 16) |
> >>> +             (((input >> 16) & 0xFF) << 8) |
> >>> +             ((input >> 24) & 0xFF);
> >>> +     return cpu_to_be32(ret);
> >>> +}
> >>> +
> >>> +#define UHS2_RES_NACK_POS    7
> >>> +#define UHS2_RES_NACK_MASK   (0x1 << UHS2_RES_NACK_POS)
> >>> +
> >>> +#define UHS2_RES_ECODE_POS   4
> >>> +#define UHS2_RES_ECODE_MASK  0x7
> >>> +#define UHS2_RES_ECODE_COND  1
> >>> +#define UHS2_RES_ECODE_ARG   2
> >>> +#define UHS2_RES_ECODE_GEN   3
> >>> +
> >>> +/* IOADR of device registers */
> >>> +#define UHS2_IOADR_GENERIC_CAPS              0x00
> >>> +#define UHS2_IOADR_PHY_CAPS          0x02
> >>> +#define UHS2_IOADR_LINK_CAPS         0x04
> >>> +#define UHS2_IOADR_RSV_CAPS          0x06
> >>> +#define UHS2_IOADR_GENERIC_SETTINGS  0x08
> >>> +#define UHS2_IOADR_PHY_SETTINGS              0x0A
> >>> +#define UHS2_IOADR_LINK_SETTINGS     0x0C
> >>> +#define UHS2_IOADR_PRESET            0x40
> >>> +
> >>> +/* SD application packets */
> >>> +#define UHS2_SD_CMD_INDEX_POS        8
> >>> +
> >>> +#define UHS2_SD_CMD_APP_POS  14
> >>> +#define UHS2_SD_CMD_APP              (1 << UHS2_SD_CMD_APP_POS)
> >>> +
> >>> +/* UHS-II Device Registers */
> >>> +#define UHS2_DEV_CONFIG_REG  0x000
> >>> +
> >>> +/* General Caps and Settings registers */
> >>> +#define UHS2_DEV_CONFIG_GEN_CAPS     (UHS2_DEV_CONFIG_REG + 0x000)
> >>> +#define UHS2_DEV_CONFIG_N_LANES_POS  8
> >>> +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
> >>> +#define UHS2_DEV_CONFIG_2L_HD_FD     0x1
> >>> +#define UHS2_DEV_CONFIG_2D1U_FD              0x2
> >>> +#define UHS2_DEV_CONFIG_1D2U_FD              0x4
> >>> +#define UHS2_DEV_CONFIG_2D2U_FD              0x8
> >>> +#define UHS2_DEV_CONFIG_DADR_POS     14
> >>> +#define UHS2_DEV_CONFIG_DADR_MASK    0x1
> >>> +#define UHS2_DEV_CONFIG_APP_POS              16
> >>> +#define UHS2_DEV_CONFIG_APP_MASK     0xFF
> >>> +#define UHS2_DEV_CONFIG_APP_SD_MEM   0x1
> >>> +
> >>> +#define UHS2_DEV_CONFIG_GEN_SET                      (UHS2_DEV_CONFIG_REG + 0x008)
> >>> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS  8
> >>> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD     0x0
> >>> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD              0x2
> >>> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD              0x3
> >>> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD              0x4
> >>> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
> >>> +
> >>> +/* PHY Caps and Settings registers */
> >>> +#define UHS2_DEV_CONFIG_PHY_CAPS     (UHS2_DEV_CONFIG_REG + 0x002)
> >>> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK       0xF
> >>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS        4
> >>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK       0x3
> >>> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS        15
> >>> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK       0x1
> >>> +#define UHS2_DEV_CONFIG_PHY_CAPS1    (UHS2_DEV_CONFIG_REG + 0x003)
> >>> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK       0xF
> >>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS        4
> >>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK       0xF
> >>> +
> >>> +#define UHS2_DEV_CONFIG_PHY_SET                      (UHS2_DEV_CONFIG_REG + 0x00A)
> >>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS    6
> >>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A              0x0
> >>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B              0x1
> >>> +
> >>> +/* LINK-TRAN Caps and Settings registers */
> >>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS               (UHS2_DEV_CONFIG_REG + 0x004)
> >>> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK                0xF
> >>> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS         4
> >>> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK                0x3
> >>> +#define UHS2_DEV_CONFIG_N_FCU_POS            8
> >>> +#define UHS2_DEV_CONFIG_N_FCU_MASK           0xFF
> >>> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS         16
> >>> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK                0x7
> >>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS              20
> >>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK     0xFFF
> >>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1              (UHS2_DEV_CONFIG_REG + 0x005)
> >>> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK              0xFF
> >>> +
> >>> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET                (UHS2_DEV_CONFIG_REG + 0x00C)
> >>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN   0x200
> >>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
> >>> +
> >>> +/* Preset register */
> >>> +#define UHS2_DEV_CONFIG_PRESET       (UHS2_DEV_CONFIG_REG + 0x040)
> >>> +
> >>> +#define UHS2_DEV_INT_REG     0x100
> >>> +
> >>> +#define UHS2_DEV_STATUS_REG  0x180
> >>> +
> >>> +#define UHS2_DEV_CMD_REG             0x200
> >>> +#define UHS2_DEV_CMD_FULL_RESET              (UHS2_DEV_CMD_REG + 0x000)
> >>> +#define UHS2_DEV_CMD_GO_DORMANT_STATE        (UHS2_DEV_CMD_REG + 0x001)
> >>> +#define UHS2_DEV_CMD_DORMANT_HIBER   BIT(7)
> >>> +#define UHS2_DEV_CMD_DEVICE_INIT     (UHS2_DEV_CMD_REG + 0x002)
> >>> +#define UHS2_DEV_INIT_COMPLETE_FLAG  BIT(11)
> >>> +#define UHS2_DEV_CMD_ENUMERATE               (UHS2_DEV_CMD_REG + 0x003)
> >>> +#define UHS2_DEV_CMD_TRANS_ABORT     (UHS2_DEV_CMD_REG + 0x004)
> >>> +
> >>> +#define UHS2_RCLK_MAX        52000000
> >>> +#define UHS2_RCLK_MIN        26000000
> >>> +
> >>> +struct sd_uhs2_wait_active_state_data {
> >>> +     struct mmc_host *host;
> >>> +     struct mmc_command *cmd;
> >>> +};
> >>> +
> >>> +#endif /* LINUX_MMC_UHS2_H */
> >>
> >
> > Thanks, Victor Shih
>

Best regards,
Ben Chuang
  
Adrian Hunter Nov. 17, 2022, 4:03 p.m. UTC | #5
On 17/11/22 08:19, Ben Chuang wrote:
> Hi,
> 
> On Wed, Nov 16, 2022 at 9:48 PM Adrian Hunter <adrian.hunter@intel.com> wrote:
>>
>> On 16/11/22 13:06, Victor Shih wrote:
>>> Hi, Adrian
>>>
>>> On Wed, Nov 2, 2022 at 1:12 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
>>>>
>>>> On 19/10/22 14:06, Victor Shih wrote:
>>>>> Add UHS-II specific data structures for commands and defines for
>>>>> registers, as described in Part 1 UHS-II Addendum Version 1.01.
>>>>>
>>>>> UHS-II related definitions are listed below:
>>>>>   1. UHS-II card capability: sd_uhs2_caps{}
>>>>>   2. UHS-II configuration: sd_uhs2_config{}
>>>>>   3. UHS-II Command structure: uhs2_command{}
>>>>>   4. UHS-II register I/O address and register field definitions: sd_uhs2.h
>>>>>
>>>>> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
>>>>> Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
>>>>> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
>>>>> ---
>>>>>
>>>>> Updates in V5:
>>>>>  - Added UHS2 interfaces in mmc_host_ops: host.h
>>>>>  - Added UHS2 VDD2 power supply in mmc_supply: host.h
>>>>>  - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
>>>>>  - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
>>>>>  - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
>>>>> ---
>>>>>  include/linux/mmc/card.h    |  42 +++++-
>>>>>  include/linux/mmc/core.h    |  13 ++
>>>>>  include/linux/mmc/host.h    |  70 +++++++++-
>>>>>  include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
>>>>>  4 files changed, 386 insertions(+), 2 deletions(-)
>>>>>  create mode 100644 include/linux/mmc/sd_uhs2.h
>>>>>
>>>>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
>>>>> index 4a42f31b7bb0..d638a2c689cf 100644
>>>>> --- a/include/linux/mmc/card.h
>>>>> +++ b/include/linux/mmc/card.h
>>>>> @@ -190,6 +190,13 @@ struct sd_switch_caps {
>>>>>  #define SD_MAX_CURRENT_400   (1 << SD_SET_CURRENT_LIMIT_400)
>>>>>  #define SD_MAX_CURRENT_600   (1 << SD_SET_CURRENT_LIMIT_600)
>>>>>  #define SD_MAX_CURRENT_800   (1 << SD_SET_CURRENT_LIMIT_800)
>>>>> +     unsigned int            sd4_curr_limit;
>>>>> +#define SD4_SET_POWER_LIMIT_0_72W    0
>>>>> +#define SD4_SET_POWER_LIMIT_1_44W    1
>>>>> +#define SD4_SET_POWER_LIMIT_2_16W    2
>>>>> +#define SD4_SET_POWER_LIMIT_2_88W    3
>>>>> +#define SD4_SET_POWER_LIMIT_1_80W    4
>>>>> +#define SD4_SET_POWER_NO_CHANGE              (-1)
>>>>>  };
>>>>>
>>>>>  struct sd_ext_reg {
>>>>> @@ -213,7 +220,35 @@ struct sd_ext_reg {
>>>>>
>>>>>  struct sd_uhs2_config {
>>>>>       u32                     node_id;
>>>>> -     /* TODO: Extend with more register configs. */
>>>>> +
>>>>> +     u32                     dap;
>>>>> +     u32                     gap;
>>>>> +     u32                     n_fcu;
>>>>> +     u32                     maxblk_len;
>>>>> +     u8                      n_lanes;
>>>>> +     u8                      dadr_len;
>>>>> +     u8                      app_type;
>>>>> +     u8                      phy_minor_rev;
>>>>> +     u8                      phy_major_rev;
>>>>> +     u8                      can_hibernate;
>>>>> +     u8                      n_lss_sync;
>>>>> +     u8                      n_lss_dir;
>>>>> +     u8                      link_minor_rev;
>>>>> +     u8                      link_major_rev;
>>>>> +     u8                      dev_type;
>>>>> +     u8                      n_data_gap;
>>>>> +
>>>>> +     u32                     n_fcu_set;
>>>>> +     u32                     maxblk_len_set;
>>>>> +     u8                      n_lanes_set;
>>>>> +     u8                      speed_range_set;
>>>>> +     u8                      n_lss_sync_set;
>>>>> +     u8                      n_lss_dir_set;
>>>>> +     u8                      n_data_gap_set;
>>>>> +     u8                      pwrctrl_mode_set;
>>>>> +     u8                      max_retry_set;
>>>>> +
>>>>> +     u8                      cfg_complete;
>>>>>  };
>>>>>
>>>>>  struct sdio_cccr {
>>>>> @@ -323,6 +358,9 @@ struct mmc_card {
>>>>>       struct sd_ext_reg       ext_perf;       /* SD extension reg for PERF */
>>>>>
>>>>>       struct sd_uhs2_config   uhs2_config;    /* SD UHS-II config */
>>>>> +     u8                      uhs2_state;     /* SD UHS-II states */
>>>>> +#define MMC_UHS2_INITIALIZED BIT(1)
>>>>> +#define MMC_UHS2_SPEED_B     BIT(2)
>>>>>
>>>>>       unsigned int            sdio_funcs;     /* number of SDIO functions */
>>>>>       atomic_t                sdio_funcs_probed; /* number of probed SDIO funcs */
>>>>> @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
>>>>>  #define mmc_card_sdio(c)     ((c)->type == MMC_TYPE_SDIO)
>>>>>  #define mmc_card_sd_combo(c) ((c)->type == MMC_TYPE_SD_COMBO)
>>>>>
>>>>> +#define mmc_card_can_poweroff_notify(c)      ((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
>>>>> +
>>>>>  #endif /* LINUX_MMC_CARD_H */
>>>>> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
>>>>> index 6efec0b9820c..2a0581d87706 100644
>>>>> --- a/include/linux/mmc/core.h
>>>>> +++ b/include/linux/mmc/core.h
>>>>> @@ -23,6 +23,14 @@ enum mmc_blk_status {
>>>>>       MMC_BLK_NEW_REQUEST,
>>>>>  };
>>>>>
>>>>> +struct uhs2_command {
>>>>> +     u16     header;
>>>>> +     u16     arg;
>>>>> +     __be32  *payload;
>>>>> +     u32     payload_len;
>>>>> +     u32     packet_len;
>>>>> +};
>>>>> +
>>>>>  struct mmc_command {
>>>>>       u32                     opcode;
>>>>>       u32                     arg;
>>>>> @@ -109,6 +117,11 @@ struct mmc_command {
>>>>>       unsigned int            busy_timeout;   /* busy detect timeout in ms */
>>>>>       struct mmc_data         *data;          /* data segment associated with cmd */
>>>>>       struct mmc_request      *mrq;           /* associated request */
>>>>> +
>>>>> +     struct uhs2_command     *uhs2_cmd;      /* UHS2 command */
>>>>> +     u8                      *uhs2_resp;     /* UHS2 native cmd resp */
>>>>> +     u8                      uhs2_resp_len;  /* UHS2 native cmd resp len */
>>>>> +     u8                      uhs2_tmode0_flag; /* UHS2 transfer mode flag */
>>>>>  };
>>>>>
>>>>>  struct mmc_data {
>>>>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
>>>>> index 895bcf7f80b7..249a9414ad10 100644
>>>>> --- a/include/linux/mmc/host.h
>>>>> +++ b/include/linux/mmc/host.h
>>>>> @@ -16,6 +16,7 @@
>>>>>  #include <linux/mmc/pm.h>
>>>>>  #include <linux/dma-direction.h>
>>>>>  #include <linux/blk-crypto-profile.h>
>>>>> +#include <linux/mmc/sd_uhs2.h>
>>>>>
>>>>>  struct mmc_ios {
>>>>>       unsigned int    clock;                  /* clock rate */
>>>>> @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
>>>>>  };
>>>>>
>>>>>  struct sd_uhs2_caps {
>>>>> -     /* TODO: Add UHS-II capabilities for the host. */
>>>>> +     u32     dap;
>>>>> +     u32     gap;
>>>>> +     u32     group_desc;
>>>>> +     u32     maxblk_len;
>>>>> +     u32     n_fcu;
>>>>> +     u8      n_lanes;
>>>>> +     u8      addr64;
>>>>> +     u8      card_type;
>>>>> +     u8      phy_rev;
>>>>> +     u8      speed_range;
>>>>> +     u8      can_hibernate;
>>>>> +     u8      n_lss_sync;
>>>>> +     u8      n_lss_dir;
>>>>> +     u8      link_rev;
>>>>> +     u8      host_type;
>>>>> +     u8      n_data_gap;
>>>>> +
>>>>> +     u32     maxblk_len_set;
>>>>> +     u32     n_fcu_set;
>>>>> +     u8      n_lanes_set;
>>>>> +     u8      n_lss_sync_set;
>>>>> +     u8      n_lss_dir_set;
>>>>> +     u8      n_data_gap_set;
>>>>> +     u8      max_retry_set;
>>>>> +};
>>>>> +
>>>>> +struct sd_uhs2_ios {
>>>>> +     bool            is_2L_HD_mode;
>>>>> +     bool            is_APP_CMD;
>>>>> +     unsigned int    power_delay_ms;         /* waiting for stable power */
>>>>> +};
>>>>> +
>>>>> +enum sd_uhs2_operation {
>>>>> +     UHS2_PHY_INIT = 0,
>>>>> +     UHS2_SET_CONFIG,
>>>>> +     UHS2_ENABLE_INT,
>>>>> +     UHS2_DISABLE_INT,
>>>>> +     UHS2_ENABLE_CLK,
>>>>> +     UHS2_DISABLE_CLK,
>>>>> +     UHS2_CHECK_DORMANT,
>>>>> +     UHS2_SET_SPEED_B,
>>>>> +     UHS2_POST_ATTACH_SD,
>>>>>  };
>>>>>
>>>>>  struct mmc_host;
>>>>> @@ -231,6 +273,20 @@ struct mmc_host_ops {
>>>>>
>>>>>       /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
>>>>>       int     (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
>>>>> +
>>>>> +     /* UHS2 interfaces */
>>>>> +     int     (*uhs2_detect_init)(struct mmc_host *host);
>>>>
>>>> Never called?
>>>
>>> Yes, I will delete it.
>>>
>>>>
>>>>> +     int     (*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
>>>>
>>>> Never called?
>>>
>>> Yes, I will delete it.
>>>
>>>>
>>>>> +     int (*uhs2_disable_clk)(struct mmc_host *host);
>>>>
>>>> Never called?
>>>
>>> Yes, I will delete it.
>>>
>>>>
>>>>> +     int (*uhs2_enable_clk)(struct mmc_host *host);
>>>>
>>>> Never called?
>>>
>>> Yes, I will delete it.
>>>
>>>>
>>>>> +
>>>>> +     /*
>>>>> +      * The uhs2_control callback is used to execute SD UHS-II specific
>>>>> +      * operations. It's mandatory to implement for hosts that supports the
>>>>> +      * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
>>>>> +      * negative errno in case of a failure or zero for success.
>>>>> +      */
>>>>> +     int     (*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
>>>>>  };
>>>>>
>>>>>  struct mmc_cqe_ops {
>>>>> @@ -323,6 +379,7 @@ struct mmc_pwrseq;
>>>>>
>>>>>  struct mmc_supply {
>>>>>       struct regulator *vmmc;         /* Card power supply */
>>>>> +     struct regulator *vmmc2;        /* UHS2 VDD2 power supply */
>>>>>       struct regulator *vqmmc;        /* Optional Vccq supply */
>>>>>       struct regulator *vqmmc2;       /* Optional supply for phy */
>>>>>  };
>>>>> @@ -344,10 +401,12 @@ struct mmc_host {
>>>>>       u32                     ocr_avail_sdio; /* SDIO-specific OCR */
>>>>>       u32                     ocr_avail_sd;   /* SD-specific OCR */
>>>>>       u32                     ocr_avail_mmc;  /* MMC-specific OCR */
>>>>> +     u32                     ocr_avail_uhs2; /* UHS2-specific OCR */
>>>>>       struct wakeup_source    *ws;            /* Enable consume of uevents */
>>>>>       u32                     max_current_330;
>>>>>       u32                     max_current_300;
>>>>>       u32                     max_current_180;
>>>>> +     u32                     max_current_180_vdd2; /* UHS2 vdd2 max curt. */
>>>>>
>>>>>  #define MMC_VDD_165_195              0x00000080      /* VDD voltage 1.65 - 1.95 */
>>>>>  #define MMC_VDD_20_21                0x00000100      /* VDD voltage 2.0 ~ 2.1 */
>>>>> @@ -366,6 +425,7 @@ struct mmc_host {
>>>>>  #define MMC_VDD_33_34                0x00200000      /* VDD voltage 3.3 ~ 3.4 */
>>>>>  #define MMC_VDD_34_35                0x00400000      /* VDD voltage 3.4 ~ 3.5 */
>>>>>  #define MMC_VDD_35_36                0x00800000      /* VDD voltage 3.5 ~ 3.6 */
>>>>> +#define MMC_VDD2_165_195     0x00000080      /* UHS2 VDD2 1.65 ~ 1.95 */
>>>>>
>>>>>       u32                     caps;           /* Host capabilities */
>>>>>
>>>>> @@ -443,7 +503,12 @@ struct mmc_host {
>>>>>  #endif
>>>>>  #define MMC_CAP2_ALT_GPT_TEGRA       (1 << 28)       /* Host with eMMC that has GPT entry at a non-standard location */
>>>>>
>>>>> +     int flags;
>>>>> +#define MMC_UHS2_SUPPORT     (1 << 0)
>>>>
>>>> MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
>>>> Both have the same value, but MMC_UHS2_SUPPORT is for
>>>> host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state
>>>>
>>>> Please use the correct flag with the correct variable.
>>>>
>>>
>>> The value of MMC_UHS2_SUPPORT is (1<<0) and the value of
>>> MMC_UHS2_INITIALIZED is BIT(1).
>>> Both have different values, therefore I'm not sure what you mean.
>>> May you give me some more advice? Thanks.
>>
>> I guess I got confused about the values, however it is not OK to
>> use MMC_UHS2_INITIALIZED for both mmc->flags and card->uhs2_state.
>> Please make a separate define with a different name for mmc->flags
>> version of MMC_UHS2_INITIALIZED.
> 
> MMC_UHS2_INITIALIZED here is used to judge that the UHS-II I/F has been
> initialized and can run in SD-TRAN. In this state,  some SD commands
> require a distinction. For example, ACMD (CMD55) should be set by the APP
> field in UHS-II packet.

OK, but SD commands cannot be sent in UHS-II mode without SD-TRAN
so is the distinction needed?

> 
>>
>> Also, I am confused about the purpose of mmc->flags and
>> card->uhs2_state.
> 
> It looks like the mmc->flags and card->uhs2_state have the same purpose.
> I think it is having trouble with card == NULL in mmc_app_cmd(*host, *card)
> in patch [V5, 06/26] so just add one more mmc->flags.
> Can wait for confirmation from Victor.
> 
>>
>> A host is UHS-II capable as represented by MMC_CAP2_SD_UHS2.
>> To initialize and use a UHS-II card in UHS-II mode, the host
>> must be in UHS-II mode.
>> To initialize and use a UHS-II card in SD mode, the host
>> must be in SD mode.
>> So the state of the card and host is always the same:
>> either UHS-II or not.  Note, that is a consequence of the
>> hardware I/F.  Whether SD I/F or UHS-II I/F is used is
>> decided before sending any UHS-II commands. SD I/F is
>> disabled during UHS-II PHY initialization, whereas
>> UHS-II I/F is disabled before execution of ACMD41 is
>> completed.
>>
>> So it seems like there would only be a need for one flag
>> to indicate UHS-II mode?
>>
>>>
>>>>> +#define MMC_UHS2_2L_HD               (1 << 2)
>>>>
>>>> MMC_UHS2_2L_HD does not seem to be used. Is it needed?
>>>
>>> I confirmed this, I don't use it, I will delete it.
>>>
>>>>
>>>>> +
>>>>>       struct sd_uhs2_caps     uhs2_caps;      /* Host UHS-II capabilities */
>>>>> +     struct sd_uhs2_ios      uhs2_ios;       /* Host UHS-II capabilities */
>>>>>
>>>>>       int                     fixed_drv_type; /* fixed driver type for non-removable media */
>>>>>
>>>>> @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
>>>>>  int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
>>>>>  int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
>>>>>
>>>>> +#define mmc_uhs2_2L_HD_mode(h)       ((h)->uhs2_ios.is_2L_HD_mode)
>>>>> +#define mmc_uhs2_APP_cmd(h)  ((h)->uhs2_ios.is_APP_CMD)
>>>>> +
>>>>>  #endif /* LINUX_MMC_HOST_H */
>>>>> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
>>>>> new file mode 100644
>>>>> index 000000000000..8fcf702cf4a5
>>>>> --- /dev/null
>>>>> +++ b/include/linux/mmc/sd_uhs2.h
>>>>> @@ -0,0 +1,263 @@
>>>>> +/* SPDX-License-Identifier: GPL-2.0-or-later */
>>>>> +/*
>>>>> + * Header file for UHS-II packets, Host Controller registers and I/O
>>>>> + * accessors.
>>>>> + *
>>>>> + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
>>>>> + */
>>>>> +#ifndef LINUX_MMC_UHS2_H
>>>>> +#define LINUX_MMC_UHS2_H
>>>>> +
>>>>> +/* LINK Layer definition */
>>>>> +/*
>>>>> + * UHS2 Header:
>>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
>>>>> + *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
>>>>> + *      bit [6:4]  : TYP(Packet Type)
>>>>> + *                   000b: CCMD(Control command packet)
>>>>> + *                   001b: DCMD(Data command packet)
>>>>> + *                   010b: RES(Response packet)
>>>>> + *                   011b: DATA(Data payload packet)
>>>>> + *                   111b: MSG(Message packet)
>>>>> + *                   Others: Reserved
>>>>> + *      bit [7]    : NP(Native Packet)
>>>>> + *      bit [10:8] : TID(Transaction ID)
>>>>> + *      bit [11]   : Reserved
>>>>> + *      bit [15:12]: SID(Source ID 0: Node ID of Host)
>>>>> + *
>>>>> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
>>>>> + */
>>>>> +/*
>>>>> + * UHS2 Argument:
>>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
>>>>> + *      bit [3:0]  : MSB of IOADR
>>>>> + *      bit [5:4]  : PLEN(Payload Length)
>>>>> + *                   00b: 0 byte
>>>>> + *                   01b: 4 bytes
>>>>> + *                   10b: 8 bytes
>>>>> + *                   11b: 16 bytes
>>>>> + *      bit [6]    : Reserved
>>>>> + *      bit [7]    : R/W(Read/Write)
>>>>> + *                   0: Control read command
>>>>> + *                   1: Control write command
>>>>> + *      bit [15:8] : LSB of IOADR
>>>>> + *
>>>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
>>>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
>>>>> + */
>>>>> +#define UHS2_NATIVE_PACKET_POS       7
>>>>> +#define UHS2_NATIVE_PACKET   (1 << UHS2_NATIVE_PACKET_POS)
>>>>> +
>>>>> +#define UHS2_PACKET_TYPE_POS 4
>>>>> +#define UHS2_PACKET_TYPE_CCMD        (0 << UHS2_PACKET_TYPE_POS)
>>>>> +#define UHS2_PACKET_TYPE_DCMD        (1 << UHS2_PACKET_TYPE_POS)
>>>>> +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
>>>>> +#define UHS2_PACKET_TYPE_DATA        (3 << UHS2_PACKET_TYPE_POS)
>>>>> +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
>>>>> +
>>>>> +#define UHS2_DEST_ID_MASK    0x0F
>>>>> +#define UHS2_DEST_ID         0x1
>>>>> +
>>>>> +#define UHS2_SRC_ID_POS              12
>>>>> +#define UHS2_SRC_ID_MASK     0xF000
>>>>> +
>>>>> +#define UHS2_TRANS_ID_POS    8
>>>>> +#define UHS2_TRANS_ID_MASK   0x0700
>>>>> +
>>>>> +/* UHS2 MSG */
>>>>> +#define UHS2_MSG_CTG_POS     5
>>>>> +#define UHS2_MSG_CTG_LMSG    0x00
>>>>> +#define UHS2_MSG_CTG_INT     0x60
>>>>> +#define UHS2_MSG_CTG_AMSG    0x80
>>>>> +
>>>>> +#define UHS2_MSG_CTG_FCREQ   0x00
>>>>> +#define UHS2_MSG_CTG_FCRDY   0x01
>>>>> +#define UHS2_MSG_CTG_STAT    0x02
>>>>> +
>>>>> +#define UHS2_MSG_CODE_POS                    8
>>>>> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR               0x8
>>>>> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR     0x8
>>>>> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR               0x1
>>>>> +
>>>>> +/* TRANS Layer definition */
>>>>> +
>>>>> +/* Native packets*/
>>>>> +#define UHS2_NATIVE_CMD_RW_POS       7
>>>>> +#define UHS2_NATIVE_CMD_WRITE        (1 << UHS2_NATIVE_CMD_RW_POS)
>>>>> +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
>>>>> +
>>>>> +#define UHS2_NATIVE_CMD_PLEN_POS     4
>>>>> +#define UHS2_NATIVE_CMD_PLEN_4B              (1 << UHS2_NATIVE_CMD_PLEN_POS)
>>>>> +#define UHS2_NATIVE_CMD_PLEN_8B              (2 << UHS2_NATIVE_CMD_PLEN_POS)
>>>>> +#define UHS2_NATIVE_CMD_PLEN_16B     (3 << UHS2_NATIVE_CMD_PLEN_POS)
>>>>> +
>>>>> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK     0xF00
>>>>> +#define UHS2_NATIVE_CCMD_MIOADR_MASK         0x0F
>>>>> +
>>>>> +#define UHS2_NATIVE_CCMD_LIOADR_POS          8
>>>>> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK     0x0FF
>>>>> +
>>>>> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG     BIT(11)
>>>>> +#define UHS2_DEV_INIT_PAYLOAD_LEN            1
>>>>> +#define UHS2_DEV_INIT_RESP_LEN                       6
>>>>> +#define UHS2_DEV_ENUM_PAYLOAD_LEN            1
>>>>> +#define UHS2_DEV_ENUM_RESP_LEN                       8
>>>>> +#define UHS2_CFG_WRITE_PAYLOAD_LEN           2
>>>>> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN              4
>>>>> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN  5
>>>>> +#define UHS2_GO_DORMANT_PAYLOAD_LEN          1
>>>>> +
>>>>> +/*
>>>>> + * UHS2 Argument:
>>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
>>>>> + *      bit [3:0]  : Reserved
>>>>> + *      bit [6:3]  : TMODE(Transfer Mode)
>>>>> + *                   bit 3: DAM(Data Access Mode)
>>>>> + *                   bit 4: TLUM(TLEN Unit Mode)
>>>>> + *                   bit 5: LM(Length Mode)
>>>>> + *                   bit 6: DM(Duplex Mode)
>>>>> + *      bit [7]    : R/W(Read/Write)
>>>>> + *                   0: Control read command
>>>>> + *                   1: Control write command
>>>>> + *      bit [15:8] : Reserved
>>>>> + *
>>>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
>>>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
>>>>> + */
>>>>> +#define UHS2_DCMD_DM_POS             6
>>>>> +#define UHS2_DCMD_2L_HD_MODE         (1 << UHS2_DCMD_DM_POS)
>>>>> +#define UHS2_DCMD_LM_POS             5
>>>>> +#define UHS2_DCMD_LM_TLEN_EXIST              (1 << UHS2_DCMD_LM_POS)
>>>>> +#define UHS2_DCMD_TLUM_POS           4
>>>>> +#define UHS2_DCMD_TLUM_BYTE_MODE     (1 << UHS2_DCMD_TLUM_POS)
>>>>> +#define UHS2_NATIVE_DCMD_DAM_POS     3
>>>>> +#define UHS2_NATIVE_DCMD_DAM_IO              (1 << UHS2_NATIVE_DCMD_DAM_POS)
>>>>> +
>>>>> +/*
>>>>> + * Per UHS2 spec, DCMD payload should be MSB first. There may be
>>>>> + * two types of data be assembled to MSB:
>>>>> + * 1. TLEN: Input block size for single read/write and number of blocks
>>>>> + * for multiple read/write to calculate TLEN as MSB first per spec.
>>>>> + * 2. SD command argument.
>>>>> + */
>>>>> +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
>>>>> +{
>>>>> +     u32 ret = 0;
>>>>> +
>>>>> +     ret = ((input & 0xFF) << 24) |
>>>>> +             (((input >> 8) & 0xFF) << 16) |
>>>>> +             (((input >> 16) & 0xFF) << 8) |
>>>>> +             ((input >> 24) & 0xFF);
>>>>> +     return cpu_to_be32(ret);
>>>>> +}
>>>>> +
>>>>> +#define UHS2_RES_NACK_POS    7
>>>>> +#define UHS2_RES_NACK_MASK   (0x1 << UHS2_RES_NACK_POS)
>>>>> +
>>>>> +#define UHS2_RES_ECODE_POS   4
>>>>> +#define UHS2_RES_ECODE_MASK  0x7
>>>>> +#define UHS2_RES_ECODE_COND  1
>>>>> +#define UHS2_RES_ECODE_ARG   2
>>>>> +#define UHS2_RES_ECODE_GEN   3
>>>>> +
>>>>> +/* IOADR of device registers */
>>>>> +#define UHS2_IOADR_GENERIC_CAPS              0x00
>>>>> +#define UHS2_IOADR_PHY_CAPS          0x02
>>>>> +#define UHS2_IOADR_LINK_CAPS         0x04
>>>>> +#define UHS2_IOADR_RSV_CAPS          0x06
>>>>> +#define UHS2_IOADR_GENERIC_SETTINGS  0x08
>>>>> +#define UHS2_IOADR_PHY_SETTINGS              0x0A
>>>>> +#define UHS2_IOADR_LINK_SETTINGS     0x0C
>>>>> +#define UHS2_IOADR_PRESET            0x40
>>>>> +
>>>>> +/* SD application packets */
>>>>> +#define UHS2_SD_CMD_INDEX_POS        8
>>>>> +
>>>>> +#define UHS2_SD_CMD_APP_POS  14
>>>>> +#define UHS2_SD_CMD_APP              (1 << UHS2_SD_CMD_APP_POS)
>>>>> +
>>>>> +/* UHS-II Device Registers */
>>>>> +#define UHS2_DEV_CONFIG_REG  0x000
>>>>> +
>>>>> +/* General Caps and Settings registers */
>>>>> +#define UHS2_DEV_CONFIG_GEN_CAPS     (UHS2_DEV_CONFIG_REG + 0x000)
>>>>> +#define UHS2_DEV_CONFIG_N_LANES_POS  8
>>>>> +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
>>>>> +#define UHS2_DEV_CONFIG_2L_HD_FD     0x1
>>>>> +#define UHS2_DEV_CONFIG_2D1U_FD              0x2
>>>>> +#define UHS2_DEV_CONFIG_1D2U_FD              0x4
>>>>> +#define UHS2_DEV_CONFIG_2D2U_FD              0x8
>>>>> +#define UHS2_DEV_CONFIG_DADR_POS     14
>>>>> +#define UHS2_DEV_CONFIG_DADR_MASK    0x1
>>>>> +#define UHS2_DEV_CONFIG_APP_POS              16
>>>>> +#define UHS2_DEV_CONFIG_APP_MASK     0xFF
>>>>> +#define UHS2_DEV_CONFIG_APP_SD_MEM   0x1
>>>>> +
>>>>> +#define UHS2_DEV_CONFIG_GEN_SET                      (UHS2_DEV_CONFIG_REG + 0x008)
>>>>> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS  8
>>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD     0x0
>>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD              0x2
>>>>> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD              0x3
>>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD              0x4
>>>>> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
>>>>> +
>>>>> +/* PHY Caps and Settings registers */
>>>>> +#define UHS2_DEV_CONFIG_PHY_CAPS     (UHS2_DEV_CONFIG_REG + 0x002)
>>>>> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK       0xF
>>>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS        4
>>>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK       0x3
>>>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS        15
>>>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK       0x1
>>>>> +#define UHS2_DEV_CONFIG_PHY_CAPS1    (UHS2_DEV_CONFIG_REG + 0x003)
>>>>> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK       0xF
>>>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS        4
>>>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK       0xF
>>>>> +
>>>>> +#define UHS2_DEV_CONFIG_PHY_SET                      (UHS2_DEV_CONFIG_REG + 0x00A)
>>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS    6
>>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A              0x0
>>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B              0x1
>>>>> +
>>>>> +/* LINK-TRAN Caps and Settings registers */
>>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS               (UHS2_DEV_CONFIG_REG + 0x004)
>>>>> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK                0xF
>>>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS         4
>>>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK                0x3
>>>>> +#define UHS2_DEV_CONFIG_N_FCU_POS            8
>>>>> +#define UHS2_DEV_CONFIG_N_FCU_MASK           0xFF
>>>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS         16
>>>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK                0x7
>>>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS              20
>>>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK     0xFFF
>>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1              (UHS2_DEV_CONFIG_REG + 0x005)
>>>>> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK              0xFF
>>>>> +
>>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET                (UHS2_DEV_CONFIG_REG + 0x00C)
>>>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN   0x200
>>>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
>>>>> +
>>>>> +/* Preset register */
>>>>> +#define UHS2_DEV_CONFIG_PRESET       (UHS2_DEV_CONFIG_REG + 0x040)
>>>>> +
>>>>> +#define UHS2_DEV_INT_REG     0x100
>>>>> +
>>>>> +#define UHS2_DEV_STATUS_REG  0x180
>>>>> +
>>>>> +#define UHS2_DEV_CMD_REG             0x200
>>>>> +#define UHS2_DEV_CMD_FULL_RESET              (UHS2_DEV_CMD_REG + 0x000)
>>>>> +#define UHS2_DEV_CMD_GO_DORMANT_STATE        (UHS2_DEV_CMD_REG + 0x001)
>>>>> +#define UHS2_DEV_CMD_DORMANT_HIBER   BIT(7)
>>>>> +#define UHS2_DEV_CMD_DEVICE_INIT     (UHS2_DEV_CMD_REG + 0x002)
>>>>> +#define UHS2_DEV_INIT_COMPLETE_FLAG  BIT(11)
>>>>> +#define UHS2_DEV_CMD_ENUMERATE               (UHS2_DEV_CMD_REG + 0x003)
>>>>> +#define UHS2_DEV_CMD_TRANS_ABORT     (UHS2_DEV_CMD_REG + 0x004)
>>>>> +
>>>>> +#define UHS2_RCLK_MAX        52000000
>>>>> +#define UHS2_RCLK_MIN        26000000
>>>>> +
>>>>> +struct sd_uhs2_wait_active_state_data {
>>>>> +     struct mmc_host *host;
>>>>> +     struct mmc_command *cmd;
>>>>> +};
>>>>> +
>>>>> +#endif /* LINUX_MMC_UHS2_H */
>>>>
>>>
>>> Thanks, Victor Shih
>>
> 
> Best regards,
> Ben Chuang
  
Ben Chuang Nov. 18, 2022, 1:19 a.m. UTC | #6
On Fri, Nov 18, 2022 at 12:05 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
>
> On 17/11/22 08:19, Ben Chuang wrote:
> > Hi,
> >
> > On Wed, Nov 16, 2022 at 9:48 PM Adrian Hunter <adrian.hunter@intel.com> wrote:
> >>
> >> On 16/11/22 13:06, Victor Shih wrote:
> >>> Hi, Adrian
> >>>
> >>> On Wed, Nov 2, 2022 at 1:12 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
> >>>>
> >>>> On 19/10/22 14:06, Victor Shih wrote:
> >>>>> Add UHS-II specific data structures for commands and defines for
> >>>>> registers, as described in Part 1 UHS-II Addendum Version 1.01.
> >>>>>
> >>>>> UHS-II related definitions are listed below:
> >>>>>   1. UHS-II card capability: sd_uhs2_caps{}
> >>>>>   2. UHS-II configuration: sd_uhs2_config{}
> >>>>>   3. UHS-II Command structure: uhs2_command{}
> >>>>>   4. UHS-II register I/O address and register field definitions: sd_uhs2.h
> >>>>>
> >>>>> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
> >>>>> Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
> >>>>> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> >>>>> ---
> >>>>>
> >>>>> Updates in V5:
> >>>>>  - Added UHS2 interfaces in mmc_host_ops: host.h
> >>>>>  - Added UHS2 VDD2 power supply in mmc_supply: host.h
> >>>>>  - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
> >>>>>  - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
> >>>>>  - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
> >>>>> ---
> >>>>>  include/linux/mmc/card.h    |  42 +++++-
> >>>>>  include/linux/mmc/core.h    |  13 ++
> >>>>>  include/linux/mmc/host.h    |  70 +++++++++-
> >>>>>  include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
> >>>>>  4 files changed, 386 insertions(+), 2 deletions(-)
> >>>>>  create mode 100644 include/linux/mmc/sd_uhs2.h
> >>>>>
> >>>>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> >>>>> index 4a42f31b7bb0..d638a2c689cf 100644
> >>>>> --- a/include/linux/mmc/card.h
> >>>>> +++ b/include/linux/mmc/card.h
> >>>>> @@ -190,6 +190,13 @@ struct sd_switch_caps {
> >>>>>  #define SD_MAX_CURRENT_400   (1 << SD_SET_CURRENT_LIMIT_400)
> >>>>>  #define SD_MAX_CURRENT_600   (1 << SD_SET_CURRENT_LIMIT_600)
> >>>>>  #define SD_MAX_CURRENT_800   (1 << SD_SET_CURRENT_LIMIT_800)
> >>>>> +     unsigned int            sd4_curr_limit;
> >>>>> +#define SD4_SET_POWER_LIMIT_0_72W    0
> >>>>> +#define SD4_SET_POWER_LIMIT_1_44W    1
> >>>>> +#define SD4_SET_POWER_LIMIT_2_16W    2
> >>>>> +#define SD4_SET_POWER_LIMIT_2_88W    3
> >>>>> +#define SD4_SET_POWER_LIMIT_1_80W    4
> >>>>> +#define SD4_SET_POWER_NO_CHANGE              (-1)
> >>>>>  };
> >>>>>
> >>>>>  struct sd_ext_reg {
> >>>>> @@ -213,7 +220,35 @@ struct sd_ext_reg {
> >>>>>
> >>>>>  struct sd_uhs2_config {
> >>>>>       u32                     node_id;
> >>>>> -     /* TODO: Extend with more register configs. */
> >>>>> +
> >>>>> +     u32                     dap;
> >>>>> +     u32                     gap;
> >>>>> +     u32                     n_fcu;
> >>>>> +     u32                     maxblk_len;
> >>>>> +     u8                      n_lanes;
> >>>>> +     u8                      dadr_len;
> >>>>> +     u8                      app_type;
> >>>>> +     u8                      phy_minor_rev;
> >>>>> +     u8                      phy_major_rev;
> >>>>> +     u8                      can_hibernate;
> >>>>> +     u8                      n_lss_sync;
> >>>>> +     u8                      n_lss_dir;
> >>>>> +     u8                      link_minor_rev;
> >>>>> +     u8                      link_major_rev;
> >>>>> +     u8                      dev_type;
> >>>>> +     u8                      n_data_gap;
> >>>>> +
> >>>>> +     u32                     n_fcu_set;
> >>>>> +     u32                     maxblk_len_set;
> >>>>> +     u8                      n_lanes_set;
> >>>>> +     u8                      speed_range_set;
> >>>>> +     u8                      n_lss_sync_set;
> >>>>> +     u8                      n_lss_dir_set;
> >>>>> +     u8                      n_data_gap_set;
> >>>>> +     u8                      pwrctrl_mode_set;
> >>>>> +     u8                      max_retry_set;
> >>>>> +
> >>>>> +     u8                      cfg_complete;
> >>>>>  };
> >>>>>
> >>>>>  struct sdio_cccr {
> >>>>> @@ -323,6 +358,9 @@ struct mmc_card {
> >>>>>       struct sd_ext_reg       ext_perf;       /* SD extension reg for PERF */
> >>>>>
> >>>>>       struct sd_uhs2_config   uhs2_config;    /* SD UHS-II config */
> >>>>> +     u8                      uhs2_state;     /* SD UHS-II states */
> >>>>> +#define MMC_UHS2_INITIALIZED BIT(1)
> >>>>> +#define MMC_UHS2_SPEED_B     BIT(2)
> >>>>>
> >>>>>       unsigned int            sdio_funcs;     /* number of SDIO functions */
> >>>>>       atomic_t                sdio_funcs_probed; /* number of probed SDIO funcs */
> >>>>> @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
> >>>>>  #define mmc_card_sdio(c)     ((c)->type == MMC_TYPE_SDIO)
> >>>>>  #define mmc_card_sd_combo(c) ((c)->type == MMC_TYPE_SD_COMBO)
> >>>>>
> >>>>> +#define mmc_card_can_poweroff_notify(c)      ((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
> >>>>> +
> >>>>>  #endif /* LINUX_MMC_CARD_H */
> >>>>> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> >>>>> index 6efec0b9820c..2a0581d87706 100644
> >>>>> --- a/include/linux/mmc/core.h
> >>>>> +++ b/include/linux/mmc/core.h
> >>>>> @@ -23,6 +23,14 @@ enum mmc_blk_status {
> >>>>>       MMC_BLK_NEW_REQUEST,
> >>>>>  };
> >>>>>
> >>>>> +struct uhs2_command {
> >>>>> +     u16     header;
> >>>>> +     u16     arg;
> >>>>> +     __be32  *payload;
> >>>>> +     u32     payload_len;
> >>>>> +     u32     packet_len;
> >>>>> +};
> >>>>> +
> >>>>>  struct mmc_command {
> >>>>>       u32                     opcode;
> >>>>>       u32                     arg;
> >>>>> @@ -109,6 +117,11 @@ struct mmc_command {
> >>>>>       unsigned int            busy_timeout;   /* busy detect timeout in ms */
> >>>>>       struct mmc_data         *data;          /* data segment associated with cmd */
> >>>>>       struct mmc_request      *mrq;           /* associated request */
> >>>>> +
> >>>>> +     struct uhs2_command     *uhs2_cmd;      /* UHS2 command */
> >>>>> +     u8                      *uhs2_resp;     /* UHS2 native cmd resp */
> >>>>> +     u8                      uhs2_resp_len;  /* UHS2 native cmd resp len */
> >>>>> +     u8                      uhs2_tmode0_flag; /* UHS2 transfer mode flag */
> >>>>>  };
> >>>>>
> >>>>>  struct mmc_data {
> >>>>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> >>>>> index 895bcf7f80b7..249a9414ad10 100644
> >>>>> --- a/include/linux/mmc/host.h
> >>>>> +++ b/include/linux/mmc/host.h
> >>>>> @@ -16,6 +16,7 @@
> >>>>>  #include <linux/mmc/pm.h>
> >>>>>  #include <linux/dma-direction.h>
> >>>>>  #include <linux/blk-crypto-profile.h>
> >>>>> +#include <linux/mmc/sd_uhs2.h>
> >>>>>
> >>>>>  struct mmc_ios {
> >>>>>       unsigned int    clock;                  /* clock rate */
> >>>>> @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
> >>>>>  };
> >>>>>
> >>>>>  struct sd_uhs2_caps {
> >>>>> -     /* TODO: Add UHS-II capabilities for the host. */
> >>>>> +     u32     dap;
> >>>>> +     u32     gap;
> >>>>> +     u32     group_desc;
> >>>>> +     u32     maxblk_len;
> >>>>> +     u32     n_fcu;
> >>>>> +     u8      n_lanes;
> >>>>> +     u8      addr64;
> >>>>> +     u8      card_type;
> >>>>> +     u8      phy_rev;
> >>>>> +     u8      speed_range;
> >>>>> +     u8      can_hibernate;
> >>>>> +     u8      n_lss_sync;
> >>>>> +     u8      n_lss_dir;
> >>>>> +     u8      link_rev;
> >>>>> +     u8      host_type;
> >>>>> +     u8      n_data_gap;
> >>>>> +
> >>>>> +     u32     maxblk_len_set;
> >>>>> +     u32     n_fcu_set;
> >>>>> +     u8      n_lanes_set;
> >>>>> +     u8      n_lss_sync_set;
> >>>>> +     u8      n_lss_dir_set;
> >>>>> +     u8      n_data_gap_set;
> >>>>> +     u8      max_retry_set;
> >>>>> +};
> >>>>> +
> >>>>> +struct sd_uhs2_ios {
> >>>>> +     bool            is_2L_HD_mode;
> >>>>> +     bool            is_APP_CMD;
> >>>>> +     unsigned int    power_delay_ms;         /* waiting for stable power */
> >>>>> +};
> >>>>> +
> >>>>> +enum sd_uhs2_operation {
> >>>>> +     UHS2_PHY_INIT = 0,
> >>>>> +     UHS2_SET_CONFIG,
> >>>>> +     UHS2_ENABLE_INT,
> >>>>> +     UHS2_DISABLE_INT,
> >>>>> +     UHS2_ENABLE_CLK,
> >>>>> +     UHS2_DISABLE_CLK,
> >>>>> +     UHS2_CHECK_DORMANT,
> >>>>> +     UHS2_SET_SPEED_B,
> >>>>> +     UHS2_POST_ATTACH_SD,
> >>>>>  };
> >>>>>
> >>>>>  struct mmc_host;
> >>>>> @@ -231,6 +273,20 @@ struct mmc_host_ops {
> >>>>>
> >>>>>       /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
> >>>>>       int     (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
> >>>>> +
> >>>>> +     /* UHS2 interfaces */
> >>>>> +     int     (*uhs2_detect_init)(struct mmc_host *host);
> >>>>
> >>>> Never called?
> >>>
> >>> Yes, I will delete it.
> >>>
> >>>>
> >>>>> +     int     (*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
> >>>>
> >>>> Never called?
> >>>
> >>> Yes, I will delete it.
> >>>
> >>>>
> >>>>> +     int (*uhs2_disable_clk)(struct mmc_host *host);
> >>>>
> >>>> Never called?
> >>>
> >>> Yes, I will delete it.
> >>>
> >>>>
> >>>>> +     int (*uhs2_enable_clk)(struct mmc_host *host);
> >>>>
> >>>> Never called?
> >>>
> >>> Yes, I will delete it.
> >>>
> >>>>
> >>>>> +
> >>>>> +     /*
> >>>>> +      * The uhs2_control callback is used to execute SD UHS-II specific
> >>>>> +      * operations. It's mandatory to implement for hosts that supports the
> >>>>> +      * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
> >>>>> +      * negative errno in case of a failure or zero for success.
> >>>>> +      */
> >>>>> +     int     (*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
> >>>>>  };
> >>>>>
> >>>>>  struct mmc_cqe_ops {
> >>>>> @@ -323,6 +379,7 @@ struct mmc_pwrseq;
> >>>>>
> >>>>>  struct mmc_supply {
> >>>>>       struct regulator *vmmc;         /* Card power supply */
> >>>>> +     struct regulator *vmmc2;        /* UHS2 VDD2 power supply */
> >>>>>       struct regulator *vqmmc;        /* Optional Vccq supply */
> >>>>>       struct regulator *vqmmc2;       /* Optional supply for phy */
> >>>>>  };
> >>>>> @@ -344,10 +401,12 @@ struct mmc_host {
> >>>>>       u32                     ocr_avail_sdio; /* SDIO-specific OCR */
> >>>>>       u32                     ocr_avail_sd;   /* SD-specific OCR */
> >>>>>       u32                     ocr_avail_mmc;  /* MMC-specific OCR */
> >>>>> +     u32                     ocr_avail_uhs2; /* UHS2-specific OCR */
> >>>>>       struct wakeup_source    *ws;            /* Enable consume of uevents */
> >>>>>       u32                     max_current_330;
> >>>>>       u32                     max_current_300;
> >>>>>       u32                     max_current_180;
> >>>>> +     u32                     max_current_180_vdd2; /* UHS2 vdd2 max curt. */
> >>>>>
> >>>>>  #define MMC_VDD_165_195              0x00000080      /* VDD voltage 1.65 - 1.95 */
> >>>>>  #define MMC_VDD_20_21                0x00000100      /* VDD voltage 2.0 ~ 2.1 */
> >>>>> @@ -366,6 +425,7 @@ struct mmc_host {
> >>>>>  #define MMC_VDD_33_34                0x00200000      /* VDD voltage 3.3 ~ 3.4 */
> >>>>>  #define MMC_VDD_34_35                0x00400000      /* VDD voltage 3.4 ~ 3.5 */
> >>>>>  #define MMC_VDD_35_36                0x00800000      /* VDD voltage 3.5 ~ 3.6 */
> >>>>> +#define MMC_VDD2_165_195     0x00000080      /* UHS2 VDD2 1.65 ~ 1.95 */
> >>>>>
> >>>>>       u32                     caps;           /* Host capabilities */
> >>>>>
> >>>>> @@ -443,7 +503,12 @@ struct mmc_host {
> >>>>>  #endif
> >>>>>  #define MMC_CAP2_ALT_GPT_TEGRA       (1 << 28)       /* Host with eMMC that has GPT entry at a non-standard location */
> >>>>>
> >>>>> +     int flags;
> >>>>> +#define MMC_UHS2_SUPPORT     (1 << 0)
> >>>>
> >>>> MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
> >>>> Both have the same value, but MMC_UHS2_SUPPORT is for
> >>>> host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state
> >>>>
> >>>> Please use the correct flag with the correct variable.
> >>>>
> >>>
> >>> The value of MMC_UHS2_SUPPORT is (1<<0) and the value of
> >>> MMC_UHS2_INITIALIZED is BIT(1).
> >>> Both have different values, therefore I'm not sure what you mean.
> >>> May you give me some more advice? Thanks.
> >>
> >> I guess I got confused about the values, however it is not OK to
> >> use MMC_UHS2_INITIALIZED for both mmc->flags and card->uhs2_state.
> >> Please make a separate define with a different name for mmc->flags
> >> version of MMC_UHS2_INITIALIZED.
> >
> > MMC_UHS2_INITIALIZED here is used to judge that the UHS-II I/F has been
> > initialized and can run in SD-TRAN. In this state,  some SD commands
> > require a distinction. For example, ACMD (CMD55) should be set by the APP
> > field in UHS-II packet.
>
> OK, but SD commands cannot be sent in UHS-II mode without SD-TRAN
> so is the distinction needed?

No need, if these SD commands are sent in SD_TRAN mode.

>
> >
> >>
> >> Also, I am confused about the purpose of mmc->flags and
> >> card->uhs2_state.
> >
> > It looks like the mmc->flags and card->uhs2_state have the same purpose.
> > I think it is having trouble with card == NULL in mmc_app_cmd(*host, *card)
> > in patch [V5, 06/26] so just add one more mmc->flags.
> > Can wait for confirmation from Victor.
> >
> >>
> >> A host is UHS-II capable as represented by MMC_CAP2_SD_UHS2.
> >> To initialize and use a UHS-II card in UHS-II mode, the host
> >> must be in UHS-II mode.
> >> To initialize and use a UHS-II card in SD mode, the host
> >> must be in SD mode.
> >> So the state of the card and host is always the same:
> >> either UHS-II or not.  Note, that is a consequence of the
> >> hardware I/F.  Whether SD I/F or UHS-II I/F is used is
> >> decided before sending any UHS-II commands. SD I/F is
> >> disabled during UHS-II PHY initialization, whereas
> >> UHS-II I/F is disabled before execution of ACMD41 is
> >> completed.
> >>
> >> So it seems like there would only be a need for one flag
> >> to indicate UHS-II mode?
> >>
> >>>
> >>>>> +#define MMC_UHS2_2L_HD               (1 << 2)
> >>>>
> >>>> MMC_UHS2_2L_HD does not seem to be used. Is it needed?
> >>>
> >>> I confirmed this, I don't use it, I will delete it.
> >>>
> >>>>
> >>>>> +
> >>>>>       struct sd_uhs2_caps     uhs2_caps;      /* Host UHS-II capabilities */
> >>>>> +     struct sd_uhs2_ios      uhs2_ios;       /* Host UHS-II capabilities */
> >>>>>
> >>>>>       int                     fixed_drv_type; /* fixed driver type for non-removable media */
> >>>>>
> >>>>> @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
> >>>>>  int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
> >>>>>  int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
> >>>>>
> >>>>> +#define mmc_uhs2_2L_HD_mode(h)       ((h)->uhs2_ios.is_2L_HD_mode)
> >>>>> +#define mmc_uhs2_APP_cmd(h)  ((h)->uhs2_ios.is_APP_CMD)
> >>>>> +
> >>>>>  #endif /* LINUX_MMC_HOST_H */
> >>>>> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
> >>>>> new file mode 100644
> >>>>> index 000000000000..8fcf702cf4a5
> >>>>> --- /dev/null
> >>>>> +++ b/include/linux/mmc/sd_uhs2.h
> >>>>> @@ -0,0 +1,263 @@
> >>>>> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> >>>>> +/*
> >>>>> + * Header file for UHS-II packets, Host Controller registers and I/O
> >>>>> + * accessors.
> >>>>> + *
> >>>>> + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
> >>>>> + */
> >>>>> +#ifndef LINUX_MMC_UHS2_H
> >>>>> +#define LINUX_MMC_UHS2_H
> >>>>> +
> >>>>> +/* LINK Layer definition */
> >>>>> +/*
> >>>>> + * UHS2 Header:
> >>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
> >>>>> + *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
> >>>>> + *      bit [6:4]  : TYP(Packet Type)
> >>>>> + *                   000b: CCMD(Control command packet)
> >>>>> + *                   001b: DCMD(Data command packet)
> >>>>> + *                   010b: RES(Response packet)
> >>>>> + *                   011b: DATA(Data payload packet)
> >>>>> + *                   111b: MSG(Message packet)
> >>>>> + *                   Others: Reserved
> >>>>> + *      bit [7]    : NP(Native Packet)
> >>>>> + *      bit [10:8] : TID(Transaction ID)
> >>>>> + *      bit [11]   : Reserved
> >>>>> + *      bit [15:12]: SID(Source ID 0: Node ID of Host)
> >>>>> + *
> >>>>> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
> >>>>> + */
> >>>>> +/*
> >>>>> + * UHS2 Argument:
> >>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
> >>>>> + *      bit [3:0]  : MSB of IOADR
> >>>>> + *      bit [5:4]  : PLEN(Payload Length)
> >>>>> + *                   00b: 0 byte
> >>>>> + *                   01b: 4 bytes
> >>>>> + *                   10b: 8 bytes
> >>>>> + *                   11b: 16 bytes
> >>>>> + *      bit [6]    : Reserved
> >>>>> + *      bit [7]    : R/W(Read/Write)
> >>>>> + *                   0: Control read command
> >>>>> + *                   1: Control write command
> >>>>> + *      bit [15:8] : LSB of IOADR
> >>>>> + *
> >>>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> >>>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> >>>>> + */
> >>>>> +#define UHS2_NATIVE_PACKET_POS       7
> >>>>> +#define UHS2_NATIVE_PACKET   (1 << UHS2_NATIVE_PACKET_POS)
> >>>>> +
> >>>>> +#define UHS2_PACKET_TYPE_POS 4
> >>>>> +#define UHS2_PACKET_TYPE_CCMD        (0 << UHS2_PACKET_TYPE_POS)
> >>>>> +#define UHS2_PACKET_TYPE_DCMD        (1 << UHS2_PACKET_TYPE_POS)
> >>>>> +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
> >>>>> +#define UHS2_PACKET_TYPE_DATA        (3 << UHS2_PACKET_TYPE_POS)
> >>>>> +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
> >>>>> +
> >>>>> +#define UHS2_DEST_ID_MASK    0x0F
> >>>>> +#define UHS2_DEST_ID         0x1
> >>>>> +
> >>>>> +#define UHS2_SRC_ID_POS              12
> >>>>> +#define UHS2_SRC_ID_MASK     0xF000
> >>>>> +
> >>>>> +#define UHS2_TRANS_ID_POS    8
> >>>>> +#define UHS2_TRANS_ID_MASK   0x0700
> >>>>> +
> >>>>> +/* UHS2 MSG */
> >>>>> +#define UHS2_MSG_CTG_POS     5
> >>>>> +#define UHS2_MSG_CTG_LMSG    0x00
> >>>>> +#define UHS2_MSG_CTG_INT     0x60
> >>>>> +#define UHS2_MSG_CTG_AMSG    0x80
> >>>>> +
> >>>>> +#define UHS2_MSG_CTG_FCREQ   0x00
> >>>>> +#define UHS2_MSG_CTG_FCRDY   0x01
> >>>>> +#define UHS2_MSG_CTG_STAT    0x02
> >>>>> +
> >>>>> +#define UHS2_MSG_CODE_POS                    8
> >>>>> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR               0x8
> >>>>> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR     0x8
> >>>>> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR               0x1
> >>>>> +
> >>>>> +/* TRANS Layer definition */
> >>>>> +
> >>>>> +/* Native packets*/
> >>>>> +#define UHS2_NATIVE_CMD_RW_POS       7
> >>>>> +#define UHS2_NATIVE_CMD_WRITE        (1 << UHS2_NATIVE_CMD_RW_POS)
> >>>>> +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
> >>>>> +
> >>>>> +#define UHS2_NATIVE_CMD_PLEN_POS     4
> >>>>> +#define UHS2_NATIVE_CMD_PLEN_4B              (1 << UHS2_NATIVE_CMD_PLEN_POS)
> >>>>> +#define UHS2_NATIVE_CMD_PLEN_8B              (2 << UHS2_NATIVE_CMD_PLEN_POS)
> >>>>> +#define UHS2_NATIVE_CMD_PLEN_16B     (3 << UHS2_NATIVE_CMD_PLEN_POS)
> >>>>> +
> >>>>> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK     0xF00
> >>>>> +#define UHS2_NATIVE_CCMD_MIOADR_MASK         0x0F
> >>>>> +
> >>>>> +#define UHS2_NATIVE_CCMD_LIOADR_POS          8
> >>>>> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK     0x0FF
> >>>>> +
> >>>>> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG     BIT(11)
> >>>>> +#define UHS2_DEV_INIT_PAYLOAD_LEN            1
> >>>>> +#define UHS2_DEV_INIT_RESP_LEN                       6
> >>>>> +#define UHS2_DEV_ENUM_PAYLOAD_LEN            1
> >>>>> +#define UHS2_DEV_ENUM_RESP_LEN                       8
> >>>>> +#define UHS2_CFG_WRITE_PAYLOAD_LEN           2
> >>>>> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN              4
> >>>>> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN  5
> >>>>> +#define UHS2_GO_DORMANT_PAYLOAD_LEN          1
> >>>>> +
> >>>>> +/*
> >>>>> + * UHS2 Argument:
> >>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
> >>>>> + *      bit [3:0]  : Reserved
> >>>>> + *      bit [6:3]  : TMODE(Transfer Mode)
> >>>>> + *                   bit 3: DAM(Data Access Mode)
> >>>>> + *                   bit 4: TLUM(TLEN Unit Mode)
> >>>>> + *                   bit 5: LM(Length Mode)
> >>>>> + *                   bit 6: DM(Duplex Mode)
> >>>>> + *      bit [7]    : R/W(Read/Write)
> >>>>> + *                   0: Control read command
> >>>>> + *                   1: Control write command
> >>>>> + *      bit [15:8] : Reserved
> >>>>> + *
> >>>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> >>>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> >>>>> + */
> >>>>> +#define UHS2_DCMD_DM_POS             6
> >>>>> +#define UHS2_DCMD_2L_HD_MODE         (1 << UHS2_DCMD_DM_POS)
> >>>>> +#define UHS2_DCMD_LM_POS             5
> >>>>> +#define UHS2_DCMD_LM_TLEN_EXIST              (1 << UHS2_DCMD_LM_POS)
> >>>>> +#define UHS2_DCMD_TLUM_POS           4
> >>>>> +#define UHS2_DCMD_TLUM_BYTE_MODE     (1 << UHS2_DCMD_TLUM_POS)
> >>>>> +#define UHS2_NATIVE_DCMD_DAM_POS     3
> >>>>> +#define UHS2_NATIVE_DCMD_DAM_IO              (1 << UHS2_NATIVE_DCMD_DAM_POS)
> >>>>> +
> >>>>> +/*
> >>>>> + * Per UHS2 spec, DCMD payload should be MSB first. There may be
> >>>>> + * two types of data be assembled to MSB:
> >>>>> + * 1. TLEN: Input block size for single read/write and number of blocks
> >>>>> + * for multiple read/write to calculate TLEN as MSB first per spec.
> >>>>> + * 2. SD command argument.
> >>>>> + */
> >>>>> +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
> >>>>> +{
> >>>>> +     u32 ret = 0;
> >>>>> +
> >>>>> +     ret = ((input & 0xFF) << 24) |
> >>>>> +             (((input >> 8) & 0xFF) << 16) |
> >>>>> +             (((input >> 16) & 0xFF) << 8) |
> >>>>> +             ((input >> 24) & 0xFF);
> >>>>> +     return cpu_to_be32(ret);
> >>>>> +}
> >>>>> +
> >>>>> +#define UHS2_RES_NACK_POS    7
> >>>>> +#define UHS2_RES_NACK_MASK   (0x1 << UHS2_RES_NACK_POS)
> >>>>> +
> >>>>> +#define UHS2_RES_ECODE_POS   4
> >>>>> +#define UHS2_RES_ECODE_MASK  0x7
> >>>>> +#define UHS2_RES_ECODE_COND  1
> >>>>> +#define UHS2_RES_ECODE_ARG   2
> >>>>> +#define UHS2_RES_ECODE_GEN   3
> >>>>> +
> >>>>> +/* IOADR of device registers */
> >>>>> +#define UHS2_IOADR_GENERIC_CAPS              0x00
> >>>>> +#define UHS2_IOADR_PHY_CAPS          0x02
> >>>>> +#define UHS2_IOADR_LINK_CAPS         0x04
> >>>>> +#define UHS2_IOADR_RSV_CAPS          0x06
> >>>>> +#define UHS2_IOADR_GENERIC_SETTINGS  0x08
> >>>>> +#define UHS2_IOADR_PHY_SETTINGS              0x0A
> >>>>> +#define UHS2_IOADR_LINK_SETTINGS     0x0C
> >>>>> +#define UHS2_IOADR_PRESET            0x40
> >>>>> +
> >>>>> +/* SD application packets */
> >>>>> +#define UHS2_SD_CMD_INDEX_POS        8
> >>>>> +
> >>>>> +#define UHS2_SD_CMD_APP_POS  14
> >>>>> +#define UHS2_SD_CMD_APP              (1 << UHS2_SD_CMD_APP_POS)
> >>>>> +
> >>>>> +/* UHS-II Device Registers */
> >>>>> +#define UHS2_DEV_CONFIG_REG  0x000
> >>>>> +
> >>>>> +/* General Caps and Settings registers */
> >>>>> +#define UHS2_DEV_CONFIG_GEN_CAPS     (UHS2_DEV_CONFIG_REG + 0x000)
> >>>>> +#define UHS2_DEV_CONFIG_N_LANES_POS  8
> >>>>> +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
> >>>>> +#define UHS2_DEV_CONFIG_2L_HD_FD     0x1
> >>>>> +#define UHS2_DEV_CONFIG_2D1U_FD              0x2
> >>>>> +#define UHS2_DEV_CONFIG_1D2U_FD              0x4
> >>>>> +#define UHS2_DEV_CONFIG_2D2U_FD              0x8
> >>>>> +#define UHS2_DEV_CONFIG_DADR_POS     14
> >>>>> +#define UHS2_DEV_CONFIG_DADR_MASK    0x1
> >>>>> +#define UHS2_DEV_CONFIG_APP_POS              16
> >>>>> +#define UHS2_DEV_CONFIG_APP_MASK     0xFF
> >>>>> +#define UHS2_DEV_CONFIG_APP_SD_MEM   0x1
> >>>>> +
> >>>>> +#define UHS2_DEV_CONFIG_GEN_SET                      (UHS2_DEV_CONFIG_REG + 0x008)
> >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS  8
> >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD     0x0
> >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD              0x2
> >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD              0x3
> >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD              0x4
> >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
> >>>>> +
> >>>>> +/* PHY Caps and Settings registers */
> >>>>> +#define UHS2_DEV_CONFIG_PHY_CAPS     (UHS2_DEV_CONFIG_REG + 0x002)
> >>>>> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK       0xF
> >>>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS        4
> >>>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK       0x3
> >>>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS        15
> >>>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK       0x1
> >>>>> +#define UHS2_DEV_CONFIG_PHY_CAPS1    (UHS2_DEV_CONFIG_REG + 0x003)
> >>>>> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK       0xF
> >>>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS        4
> >>>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK       0xF
> >>>>> +
> >>>>> +#define UHS2_DEV_CONFIG_PHY_SET                      (UHS2_DEV_CONFIG_REG + 0x00A)
> >>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS    6
> >>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A              0x0
> >>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B              0x1
> >>>>> +
> >>>>> +/* LINK-TRAN Caps and Settings registers */
> >>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS               (UHS2_DEV_CONFIG_REG + 0x004)
> >>>>> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK                0xF
> >>>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS         4
> >>>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK                0x3
> >>>>> +#define UHS2_DEV_CONFIG_N_FCU_POS            8
> >>>>> +#define UHS2_DEV_CONFIG_N_FCU_MASK           0xFF
> >>>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS         16
> >>>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK                0x7
> >>>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS              20
> >>>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK     0xFFF
> >>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1              (UHS2_DEV_CONFIG_REG + 0x005)
> >>>>> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK              0xFF
> >>>>> +
> >>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET                (UHS2_DEV_CONFIG_REG + 0x00C)
> >>>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN   0x200
> >>>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
> >>>>> +
> >>>>> +/* Preset register */
> >>>>> +#define UHS2_DEV_CONFIG_PRESET       (UHS2_DEV_CONFIG_REG + 0x040)
> >>>>> +
> >>>>> +#define UHS2_DEV_INT_REG     0x100
> >>>>> +
> >>>>> +#define UHS2_DEV_STATUS_REG  0x180
> >>>>> +
> >>>>> +#define UHS2_DEV_CMD_REG             0x200
> >>>>> +#define UHS2_DEV_CMD_FULL_RESET              (UHS2_DEV_CMD_REG + 0x000)
> >>>>> +#define UHS2_DEV_CMD_GO_DORMANT_STATE        (UHS2_DEV_CMD_REG + 0x001)
> >>>>> +#define UHS2_DEV_CMD_DORMANT_HIBER   BIT(7)
> >>>>> +#define UHS2_DEV_CMD_DEVICE_INIT     (UHS2_DEV_CMD_REG + 0x002)
> >>>>> +#define UHS2_DEV_INIT_COMPLETE_FLAG  BIT(11)
> >>>>> +#define UHS2_DEV_CMD_ENUMERATE               (UHS2_DEV_CMD_REG + 0x003)
> >>>>> +#define UHS2_DEV_CMD_TRANS_ABORT     (UHS2_DEV_CMD_REG + 0x004)
> >>>>> +
> >>>>> +#define UHS2_RCLK_MAX        52000000
> >>>>> +#define UHS2_RCLK_MIN        26000000
> >>>>> +
> >>>>> +struct sd_uhs2_wait_active_state_data {
> >>>>> +     struct mmc_host *host;
> >>>>> +     struct mmc_command *cmd;
> >>>>> +};
> >>>>> +
> >>>>> +#endif /* LINUX_MMC_UHS2_H */
> >>>>
> >>>
> >>> Thanks, Victor Shih
> >>
> >
> > Best regards,
> > Ben Chuang
>
  
Victor Shih Dec. 13, 2022, 8:44 a.m. UTC | #7
Hi, Adrian

On Fri, Nov 18, 2022 at 9:20 AM Ben Chuang <benchuanggli@gmail.com> wrote:
>
> On Fri, Nov 18, 2022 at 12:05 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
> >
> > On 17/11/22 08:19, Ben Chuang wrote:
> > > Hi,
> > >
> > > On Wed, Nov 16, 2022 at 9:48 PM Adrian Hunter <adrian.hunter@intel.com> wrote:
> > >>
> > >> On 16/11/22 13:06, Victor Shih wrote:
> > >>> Hi, Adrian
> > >>>
> > >>> On Wed, Nov 2, 2022 at 1:12 AM Adrian Hunter <adrian.hunter@intel.com> wrote:
> > >>>>
> > >>>> On 19/10/22 14:06, Victor Shih wrote:
> > >>>>> Add UHS-II specific data structures for commands and defines for
> > >>>>> registers, as described in Part 1 UHS-II Addendum Version 1.01.
> > >>>>>
> > >>>>> UHS-II related definitions are listed below:
> > >>>>>   1. UHS-II card capability: sd_uhs2_caps{}
> > >>>>>   2. UHS-II configuration: sd_uhs2_config{}
> > >>>>>   3. UHS-II Command structure: uhs2_command{}
> > >>>>>   4. UHS-II register I/O address and register field definitions: sd_uhs2.h
> > >>>>>
> > >>>>> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
> > >>>>> Signed-off-by: Jason Lai <jason.lai@genesyslogic.com.tw>
> > >>>>> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> > >>>>> ---
> > >>>>>
> > >>>>> Updates in V5:
> > >>>>>  - Added UHS2 interfaces in mmc_host_ops: host.h
> > >>>>>  - Added UHS2 VDD2 power supply in mmc_supply: host.h
> > >>>>>  - Added UHS2-specific OCR and UHS2 VDD2 max current in mmc_host: host.h
> > >>>>>  - Added definition of UHS2 VDD2 1.65v-1.95v in mmc_host: host.h
> > >>>>>  - Added flags/MMC_UHS2_SUPPORT/MMC_UHS2_2L_HD in mmc_host: host.h
> > >>>>> ---
> > >>>>>  include/linux/mmc/card.h    |  42 +++++-
> > >>>>>  include/linux/mmc/core.h    |  13 ++
> > >>>>>  include/linux/mmc/host.h    |  70 +++++++++-
> > >>>>>  include/linux/mmc/sd_uhs2.h | 263 ++++++++++++++++++++++++++++++++++++
> > >>>>>  4 files changed, 386 insertions(+), 2 deletions(-)
> > >>>>>  create mode 100644 include/linux/mmc/sd_uhs2.h
> > >>>>>
> > >>>>> diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
> > >>>>> index 4a42f31b7bb0..d638a2c689cf 100644
> > >>>>> --- a/include/linux/mmc/card.h
> > >>>>> +++ b/include/linux/mmc/card.h
> > >>>>> @@ -190,6 +190,13 @@ struct sd_switch_caps {
> > >>>>>  #define SD_MAX_CURRENT_400   (1 << SD_SET_CURRENT_LIMIT_400)
> > >>>>>  #define SD_MAX_CURRENT_600   (1 << SD_SET_CURRENT_LIMIT_600)
> > >>>>>  #define SD_MAX_CURRENT_800   (1 << SD_SET_CURRENT_LIMIT_800)
> > >>>>> +     unsigned int            sd4_curr_limit;
> > >>>>> +#define SD4_SET_POWER_LIMIT_0_72W    0
> > >>>>> +#define SD4_SET_POWER_LIMIT_1_44W    1
> > >>>>> +#define SD4_SET_POWER_LIMIT_2_16W    2
> > >>>>> +#define SD4_SET_POWER_LIMIT_2_88W    3
> > >>>>> +#define SD4_SET_POWER_LIMIT_1_80W    4
> > >>>>> +#define SD4_SET_POWER_NO_CHANGE              (-1)
> > >>>>>  };
> > >>>>>
> > >>>>>  struct sd_ext_reg {
> > >>>>> @@ -213,7 +220,35 @@ struct sd_ext_reg {
> > >>>>>
> > >>>>>  struct sd_uhs2_config {
> > >>>>>       u32                     node_id;
> > >>>>> -     /* TODO: Extend with more register configs. */
> > >>>>> +
> > >>>>> +     u32                     dap;
> > >>>>> +     u32                     gap;
> > >>>>> +     u32                     n_fcu;
> > >>>>> +     u32                     maxblk_len;
> > >>>>> +     u8                      n_lanes;
> > >>>>> +     u8                      dadr_len;
> > >>>>> +     u8                      app_type;
> > >>>>> +     u8                      phy_minor_rev;
> > >>>>> +     u8                      phy_major_rev;
> > >>>>> +     u8                      can_hibernate;
> > >>>>> +     u8                      n_lss_sync;
> > >>>>> +     u8                      n_lss_dir;
> > >>>>> +     u8                      link_minor_rev;
> > >>>>> +     u8                      link_major_rev;
> > >>>>> +     u8                      dev_type;
> > >>>>> +     u8                      n_data_gap;
> > >>>>> +
> > >>>>> +     u32                     n_fcu_set;
> > >>>>> +     u32                     maxblk_len_set;
> > >>>>> +     u8                      n_lanes_set;
> > >>>>> +     u8                      speed_range_set;
> > >>>>> +     u8                      n_lss_sync_set;
> > >>>>> +     u8                      n_lss_dir_set;
> > >>>>> +     u8                      n_data_gap_set;
> > >>>>> +     u8                      pwrctrl_mode_set;
> > >>>>> +     u8                      max_retry_set;
> > >>>>> +
> > >>>>> +     u8                      cfg_complete;
> > >>>>>  };
> > >>>>>
> > >>>>>  struct sdio_cccr {
> > >>>>> @@ -323,6 +358,9 @@ struct mmc_card {
> > >>>>>       struct sd_ext_reg       ext_perf;       /* SD extension reg for PERF */
> > >>>>>
> > >>>>>       struct sd_uhs2_config   uhs2_config;    /* SD UHS-II config */
> > >>>>> +     u8                      uhs2_state;     /* SD UHS-II states */
> > >>>>> +#define MMC_UHS2_INITIALIZED BIT(1)
> > >>>>> +#define MMC_UHS2_SPEED_B     BIT(2)
> > >>>>>
> > >>>>>       unsigned int            sdio_funcs;     /* number of SDIO functions */
> > >>>>>       atomic_t                sdio_funcs_probed; /* number of probed SDIO funcs */
> > >>>>> @@ -364,4 +402,6 @@ bool mmc_card_is_blockaddr(struct mmc_card *card);
> > >>>>>  #define mmc_card_sdio(c)     ((c)->type == MMC_TYPE_SDIO)
> > >>>>>  #define mmc_card_sd_combo(c) ((c)->type == MMC_TYPE_SD_COMBO)
> > >>>>>
> > >>>>> +#define mmc_card_can_poweroff_notify(c)      ((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
> > >>>>> +
> > >>>>>  #endif /* LINUX_MMC_CARD_H */
> > >>>>> diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
> > >>>>> index 6efec0b9820c..2a0581d87706 100644
> > >>>>> --- a/include/linux/mmc/core.h
> > >>>>> +++ b/include/linux/mmc/core.h
> > >>>>> @@ -23,6 +23,14 @@ enum mmc_blk_status {
> > >>>>>       MMC_BLK_NEW_REQUEST,
> > >>>>>  };
> > >>>>>
> > >>>>> +struct uhs2_command {
> > >>>>> +     u16     header;
> > >>>>> +     u16     arg;
> > >>>>> +     __be32  *payload;
> > >>>>> +     u32     payload_len;
> > >>>>> +     u32     packet_len;
> > >>>>> +};
> > >>>>> +
> > >>>>>  struct mmc_command {
> > >>>>>       u32                     opcode;
> > >>>>>       u32                     arg;
> > >>>>> @@ -109,6 +117,11 @@ struct mmc_command {
> > >>>>>       unsigned int            busy_timeout;   /* busy detect timeout in ms */
> > >>>>>       struct mmc_data         *data;          /* data segment associated with cmd */
> > >>>>>       struct mmc_request      *mrq;           /* associated request */
> > >>>>> +
> > >>>>> +     struct uhs2_command     *uhs2_cmd;      /* UHS2 command */
> > >>>>> +     u8                      *uhs2_resp;     /* UHS2 native cmd resp */
> > >>>>> +     u8                      uhs2_resp_len;  /* UHS2 native cmd resp len */
> > >>>>> +     u8                      uhs2_tmode0_flag; /* UHS2 transfer mode flag */
> > >>>>>  };
> > >>>>>
> > >>>>>  struct mmc_data {
> > >>>>> diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
> > >>>>> index 895bcf7f80b7..249a9414ad10 100644
> > >>>>> --- a/include/linux/mmc/host.h
> > >>>>> +++ b/include/linux/mmc/host.h
> > >>>>> @@ -16,6 +16,7 @@
> > >>>>>  #include <linux/mmc/pm.h>
> > >>>>>  #include <linux/dma-direction.h>
> > >>>>>  #include <linux/blk-crypto-profile.h>
> > >>>>> +#include <linux/mmc/sd_uhs2.h>
> > >>>>>
> > >>>>>  struct mmc_ios {
> > >>>>>       unsigned int    clock;                  /* clock rate */
> > >>>>> @@ -96,7 +97,48 @@ struct mmc_clk_phase_map {
> > >>>>>  };
> > >>>>>
> > >>>>>  struct sd_uhs2_caps {
> > >>>>> -     /* TODO: Add UHS-II capabilities for the host. */
> > >>>>> +     u32     dap;
> > >>>>> +     u32     gap;
> > >>>>> +     u32     group_desc;
> > >>>>> +     u32     maxblk_len;
> > >>>>> +     u32     n_fcu;
> > >>>>> +     u8      n_lanes;
> > >>>>> +     u8      addr64;
> > >>>>> +     u8      card_type;
> > >>>>> +     u8      phy_rev;
> > >>>>> +     u8      speed_range;
> > >>>>> +     u8      can_hibernate;
> > >>>>> +     u8      n_lss_sync;
> > >>>>> +     u8      n_lss_dir;
> > >>>>> +     u8      link_rev;
> > >>>>> +     u8      host_type;
> > >>>>> +     u8      n_data_gap;
> > >>>>> +
> > >>>>> +     u32     maxblk_len_set;
> > >>>>> +     u32     n_fcu_set;
> > >>>>> +     u8      n_lanes_set;
> > >>>>> +     u8      n_lss_sync_set;
> > >>>>> +     u8      n_lss_dir_set;
> > >>>>> +     u8      n_data_gap_set;
> > >>>>> +     u8      max_retry_set;
> > >>>>> +};
> > >>>>> +
> > >>>>> +struct sd_uhs2_ios {
> > >>>>> +     bool            is_2L_HD_mode;
> > >>>>> +     bool            is_APP_CMD;
> > >>>>> +     unsigned int    power_delay_ms;         /* waiting for stable power */
> > >>>>> +};
> > >>>>> +
> > >>>>> +enum sd_uhs2_operation {
> > >>>>> +     UHS2_PHY_INIT = 0,
> > >>>>> +     UHS2_SET_CONFIG,
> > >>>>> +     UHS2_ENABLE_INT,
> > >>>>> +     UHS2_DISABLE_INT,
> > >>>>> +     UHS2_ENABLE_CLK,
> > >>>>> +     UHS2_DISABLE_CLK,
> > >>>>> +     UHS2_CHECK_DORMANT,
> > >>>>> +     UHS2_SET_SPEED_B,
> > >>>>> +     UHS2_POST_ATTACH_SD,
> > >>>>>  };
> > >>>>>
> > >>>>>  struct mmc_host;
> > >>>>> @@ -231,6 +273,20 @@ struct mmc_host_ops {
> > >>>>>
> > >>>>>       /* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
> > >>>>>       int     (*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
> > >>>>> +
> > >>>>> +     /* UHS2 interfaces */
> > >>>>> +     int     (*uhs2_detect_init)(struct mmc_host *host);
> > >>>>
> > >>>> Never called?
> > >>>
> > >>> Yes, I will delete it.
> > >>>

I will update it in the patch#5 of the new [PATCH V6].

> > >>>>
> > >>>>> +     int     (*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
> > >>>>
> > >>>> Never called?
> > >>>
> > >>> Yes, I will delete it.
> > >>>

I will update it in the patch#5 of the new [PATCH V6].

> > >>>>
> > >>>>> +     int (*uhs2_disable_clk)(struct mmc_host *host);
> > >>>>
> > >>>> Never called?
> > >>>
> > >>> Yes, I will delete it.
> > >>>

I will update it in the patch#5 of the new [PATCH V6].

> > >>>>
> > >>>>> +     int (*uhs2_enable_clk)(struct mmc_host *host);
> > >>>>
> > >>>> Never called?
> > >>>
> > >>> Yes, I will delete it.
> > >>>

I will update it in the patch#5 of the new [PATCH V6].

> > >>>>
> > >>>>> +
> > >>>>> +     /*
> > >>>>> +      * The uhs2_control callback is used to execute SD UHS-II specific
> > >>>>> +      * operations. It's mandatory to implement for hosts that supports the
> > >>>>> +      * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
> > >>>>> +      * negative errno in case of a failure or zero for success.
> > >>>>> +      */
> > >>>>> +     int     (*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
> > >>>>>  };
> > >>>>>
> > >>>>>  struct mmc_cqe_ops {
> > >>>>> @@ -323,6 +379,7 @@ struct mmc_pwrseq;
> > >>>>>
> > >>>>>  struct mmc_supply {
> > >>>>>       struct regulator *vmmc;         /* Card power supply */
> > >>>>> +     struct regulator *vmmc2;        /* UHS2 VDD2 power supply */
> > >>>>>       struct regulator *vqmmc;        /* Optional Vccq supply */
> > >>>>>       struct regulator *vqmmc2;       /* Optional supply for phy */
> > >>>>>  };
> > >>>>> @@ -344,10 +401,12 @@ struct mmc_host {
> > >>>>>       u32                     ocr_avail_sdio; /* SDIO-specific OCR */
> > >>>>>       u32                     ocr_avail_sd;   /* SD-specific OCR */
> > >>>>>       u32                     ocr_avail_mmc;  /* MMC-specific OCR */
> > >>>>> +     u32                     ocr_avail_uhs2; /* UHS2-specific OCR */
> > >>>>>       struct wakeup_source    *ws;            /* Enable consume of uevents */
> > >>>>>       u32                     max_current_330;
> > >>>>>       u32                     max_current_300;
> > >>>>>       u32                     max_current_180;
> > >>>>> +     u32                     max_current_180_vdd2; /* UHS2 vdd2 max curt. */
> > >>>>>
> > >>>>>  #define MMC_VDD_165_195              0x00000080      /* VDD voltage 1.65 - 1.95 */
> > >>>>>  #define MMC_VDD_20_21                0x00000100      /* VDD voltage 2.0 ~ 2.1 */
> > >>>>> @@ -366,6 +425,7 @@ struct mmc_host {
> > >>>>>  #define MMC_VDD_33_34                0x00200000      /* VDD voltage 3.3 ~ 3.4 */
> > >>>>>  #define MMC_VDD_34_35                0x00400000      /* VDD voltage 3.4 ~ 3.5 */
> > >>>>>  #define MMC_VDD_35_36                0x00800000      /* VDD voltage 3.5 ~ 3.6 */
> > >>>>> +#define MMC_VDD2_165_195     0x00000080      /* UHS2 VDD2 1.65 ~ 1.95 */
> > >>>>>
> > >>>>>       u32                     caps;           /* Host capabilities */
> > >>>>>
> > >>>>> @@ -443,7 +503,12 @@ struct mmc_host {
> > >>>>>  #endif
> > >>>>>  #define MMC_CAP2_ALT_GPT_TEGRA       (1 << 28)       /* Host with eMMC that has GPT entry at a non-standard location */
> > >>>>>
> > >>>>> +     int flags;
> > >>>>> +#define MMC_UHS2_SUPPORT     (1 << 0)
> > >>>>
> > >>>> MMC_UHS2_SUPPORT is getting mixed up with MMC_UHS2_INITIALIZED.
> > >>>> Both have the same value, but MMC_UHS2_SUPPORT is for
> > >>>> host->flags and MMC_UHS2_INITIALIZED is for card->uhs2_state
> > >>>>
> > >>>> Please use the correct flag with the correct variable.
> > >>>>
> > >>>
> > >>> The value of MMC_UHS2_SUPPORT is (1<<0) and the value of
> > >>> MMC_UHS2_INITIALIZED is BIT(1).
> > >>> Both have different values, therefore I'm not sure what you mean.
> > >>> May you give me some more advice? Thanks.
> > >>
> > >> I guess I got confused about the values, however it is not OK to
> > >> use MMC_UHS2_INITIALIZED for both mmc->flags and card->uhs2_state.
> > >> Please make a separate define with a different name for mmc->flags
> > >> version of MMC_UHS2_INITIALIZED.
> > >
> > > MMC_UHS2_INITIALIZED here is used to judge that the UHS-II I/F has been
> > > initialized and can run in SD-TRAN. In this state,  some SD commands
> > > require a distinction. For example, ACMD (CMD55) should be set by the APP
> > > field in UHS-II packet.
> >
> > OK, but SD commands cannot be sent in UHS-II mode without SD-TRAN
> > so is the distinction needed?
>
> No need, if these SD commands are sent in SD_TRAN mode.
>

I will update it in the the new [PATCH V6].

> >
> > >
> > >>
> > >> Also, I am confused about the purpose of mmc->flags and
> > >> card->uhs2_state.
> > >
> > > It looks like the mmc->flags and card->uhs2_state have the same purpose.
> > > I think it is having trouble with card == NULL in mmc_app_cmd(*host, *card)
> > > in patch [V5, 06/26] so just add one more mmc->flags.
> > > Can wait for confirmation from Victor.
> > >
> > >>
> > >> A host is UHS-II capable as represented by MMC_CAP2_SD_UHS2.
> > >> To initialize and use a UHS-II card in UHS-II mode, the host
> > >> must be in UHS-II mode.
> > >> To initialize and use a UHS-II card in SD mode, the host
> > >> must be in SD mode.
> > >> So the state of the card and host is always the same:
> > >> either UHS-II or not.  Note, that is a consequence of the
> > >> hardware I/F.  Whether SD I/F or UHS-II I/F is used is
> > >> decided before sending any UHS-II commands. SD I/F is
> > >> disabled during UHS-II PHY initialization, whereas
> > >> UHS-II I/F is disabled before execution of ACMD41 is
> > >> completed.
> > >>
> > >> So it seems like there would only be a need for one flag
> > >> to indicate UHS-II mode?
> > >>
> > >>>
> > >>>>> +#define MMC_UHS2_2L_HD               (1 << 2)
> > >>>>
> > >>>> MMC_UHS2_2L_HD does not seem to be used. Is it needed?
> > >>>
> > >>> I confirmed this, I don't use it, I will delete it.
> > >>>

I will update it in the patch#5 of the new [PATCH V6].

> > >>>>
> > >>>>> +
> > >>>>>       struct sd_uhs2_caps     uhs2_caps;      /* Host UHS-II capabilities */
> > >>>>> +     struct sd_uhs2_ios      uhs2_ios;       /* Host UHS-II capabilities */
> > >>>>>
> > >>>>>       int                     fixed_drv_type; /* fixed driver type for non-removable media */
> > >>>>>
> > >>>>> @@ -695,4 +760,7 @@ int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
> > >>>>>  int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
> > >>>>>  int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
> > >>>>>
> > >>>>> +#define mmc_uhs2_2L_HD_mode(h)       ((h)->uhs2_ios.is_2L_HD_mode)
> > >>>>> +#define mmc_uhs2_APP_cmd(h)  ((h)->uhs2_ios.is_APP_CMD)
> > >>>>> +
> > >>>>>  #endif /* LINUX_MMC_HOST_H */
> > >>>>> diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
> > >>>>> new file mode 100644
> > >>>>> index 000000000000..8fcf702cf4a5
> > >>>>> --- /dev/null
> > >>>>> +++ b/include/linux/mmc/sd_uhs2.h
> > >>>>> @@ -0,0 +1,263 @@
> > >>>>> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > >>>>> +/*
> > >>>>> + * Header file for UHS-II packets, Host Controller registers and I/O
> > >>>>> + * accessors.
> > >>>>> + *
> > >>>>> + *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
> > >>>>> + */
> > >>>>> +#ifndef LINUX_MMC_UHS2_H
> > >>>>> +#define LINUX_MMC_UHS2_H
> > >>>>> +
> > >>>>> +/* LINK Layer definition */
> > >>>>> +/*
> > >>>>> + * UHS2 Header:
> > >>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
> > >>>>> + *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
> > >>>>> + *      bit [6:4]  : TYP(Packet Type)
> > >>>>> + *                   000b: CCMD(Control command packet)
> > >>>>> + *                   001b: DCMD(Data command packet)
> > >>>>> + *                   010b: RES(Response packet)
> > >>>>> + *                   011b: DATA(Data payload packet)
> > >>>>> + *                   111b: MSG(Message packet)
> > >>>>> + *                   Others: Reserved
> > >>>>> + *      bit [7]    : NP(Native Packet)
> > >>>>> + *      bit [10:8] : TID(Transaction ID)
> > >>>>> + *      bit [11]   : Reserved
> > >>>>> + *      bit [15:12]: SID(Source ID 0: Node ID of Host)
> > >>>>> + *
> > >>>>> + * Broadcast CCMD issued by Host is represented as DID=SID=0.
> > >>>>> + */
> > >>>>> +/*
> > >>>>> + * UHS2 Argument:
> > >>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
> > >>>>> + *      bit [3:0]  : MSB of IOADR
> > >>>>> + *      bit [5:4]  : PLEN(Payload Length)
> > >>>>> + *                   00b: 0 byte
> > >>>>> + *                   01b: 4 bytes
> > >>>>> + *                   10b: 8 bytes
> > >>>>> + *                   11b: 16 bytes
> > >>>>> + *      bit [6]    : Reserved
> > >>>>> + *      bit [7]    : R/W(Read/Write)
> > >>>>> + *                   0: Control read command
> > >>>>> + *                   1: Control write command
> > >>>>> + *      bit [15:8] : LSB of IOADR
> > >>>>> + *
> > >>>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> > >>>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> > >>>>> + */
> > >>>>> +#define UHS2_NATIVE_PACKET_POS       7
> > >>>>> +#define UHS2_NATIVE_PACKET   (1 << UHS2_NATIVE_PACKET_POS)
> > >>>>> +
> > >>>>> +#define UHS2_PACKET_TYPE_POS 4
> > >>>>> +#define UHS2_PACKET_TYPE_CCMD        (0 << UHS2_PACKET_TYPE_POS)
> > >>>>> +#define UHS2_PACKET_TYPE_DCMD        (1 << UHS2_PACKET_TYPE_POS)
> > >>>>> +#define UHS2_PACKET_TYPE_RES (2 << UHS2_PACKET_TYPE_POS)
> > >>>>> +#define UHS2_PACKET_TYPE_DATA        (3 << UHS2_PACKET_TYPE_POS)
> > >>>>> +#define UHS2_PACKET_TYPE_MSG (7 << UHS2_PACKET_TYPE_POS)
> > >>>>> +
> > >>>>> +#define UHS2_DEST_ID_MASK    0x0F
> > >>>>> +#define UHS2_DEST_ID         0x1
> > >>>>> +
> > >>>>> +#define UHS2_SRC_ID_POS              12
> > >>>>> +#define UHS2_SRC_ID_MASK     0xF000
> > >>>>> +
> > >>>>> +#define UHS2_TRANS_ID_POS    8
> > >>>>> +#define UHS2_TRANS_ID_MASK   0x0700
> > >>>>> +
> > >>>>> +/* UHS2 MSG */
> > >>>>> +#define UHS2_MSG_CTG_POS     5
> > >>>>> +#define UHS2_MSG_CTG_LMSG    0x00
> > >>>>> +#define UHS2_MSG_CTG_INT     0x60
> > >>>>> +#define UHS2_MSG_CTG_AMSG    0x80
> > >>>>> +
> > >>>>> +#define UHS2_MSG_CTG_FCREQ   0x00
> > >>>>> +#define UHS2_MSG_CTG_FCRDY   0x01
> > >>>>> +#define UHS2_MSG_CTG_STAT    0x02
> > >>>>> +
> > >>>>> +#define UHS2_MSG_CODE_POS                    8
> > >>>>> +#define UHS2_MSG_CODE_FC_UNRECOVER_ERR               0x8
> > >>>>> +#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR     0x8
> > >>>>> +#define UHS2_MSG_CODE_STAT_RECOVER_ERR               0x1
> > >>>>> +
> > >>>>> +/* TRANS Layer definition */
> > >>>>> +
> > >>>>> +/* Native packets*/
> > >>>>> +#define UHS2_NATIVE_CMD_RW_POS       7
> > >>>>> +#define UHS2_NATIVE_CMD_WRITE        (1 << UHS2_NATIVE_CMD_RW_POS)
> > >>>>> +#define UHS2_NATIVE_CMD_READ (0 << UHS2_NATIVE_CMD_RW_POS)
> > >>>>> +
> > >>>>> +#define UHS2_NATIVE_CMD_PLEN_POS     4
> > >>>>> +#define UHS2_NATIVE_CMD_PLEN_4B              (1 << UHS2_NATIVE_CMD_PLEN_POS)
> > >>>>> +#define UHS2_NATIVE_CMD_PLEN_8B              (2 << UHS2_NATIVE_CMD_PLEN_POS)
> > >>>>> +#define UHS2_NATIVE_CMD_PLEN_16B     (3 << UHS2_NATIVE_CMD_PLEN_POS)
> > >>>>> +
> > >>>>> +#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK     0xF00
> > >>>>> +#define UHS2_NATIVE_CCMD_MIOADR_MASK         0x0F
> > >>>>> +
> > >>>>> +#define UHS2_NATIVE_CCMD_LIOADR_POS          8
> > >>>>> +#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK     0x0FF
> > >>>>> +
> > >>>>> +#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG     BIT(11)
> > >>>>> +#define UHS2_DEV_INIT_PAYLOAD_LEN            1
> > >>>>> +#define UHS2_DEV_INIT_RESP_LEN                       6
> > >>>>> +#define UHS2_DEV_ENUM_PAYLOAD_LEN            1
> > >>>>> +#define UHS2_DEV_ENUM_RESP_LEN                       8
> > >>>>> +#define UHS2_CFG_WRITE_PAYLOAD_LEN           2
> > >>>>> +#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN              4
> > >>>>> +#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN  5
> > >>>>> +#define UHS2_GO_DORMANT_PAYLOAD_LEN          1
> > >>>>> +
> > >>>>> +/*
> > >>>>> + * UHS2 Argument:
> > >>>>> + * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
> > >>>>> + *      bit [3:0]  : Reserved
> > >>>>> + *      bit [6:3]  : TMODE(Transfer Mode)
> > >>>>> + *                   bit 3: DAM(Data Access Mode)
> > >>>>> + *                   bit 4: TLUM(TLEN Unit Mode)
> > >>>>> + *                   bit 5: LM(Length Mode)
> > >>>>> + *                   bit 6: DM(Duplex Mode)
> > >>>>> + *      bit [7]    : R/W(Read/Write)
> > >>>>> + *                   0: Control read command
> > >>>>> + *                   1: Control write command
> > >>>>> + *      bit [15:8] : Reserved
> > >>>>> + *
> > >>>>> + * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
> > >>>>> + * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
> > >>>>> + */
> > >>>>> +#define UHS2_DCMD_DM_POS             6
> > >>>>> +#define UHS2_DCMD_2L_HD_MODE         (1 << UHS2_DCMD_DM_POS)
> > >>>>> +#define UHS2_DCMD_LM_POS             5
> > >>>>> +#define UHS2_DCMD_LM_TLEN_EXIST              (1 << UHS2_DCMD_LM_POS)
> > >>>>> +#define UHS2_DCMD_TLUM_POS           4
> > >>>>> +#define UHS2_DCMD_TLUM_BYTE_MODE     (1 << UHS2_DCMD_TLUM_POS)
> > >>>>> +#define UHS2_NATIVE_DCMD_DAM_POS     3
> > >>>>> +#define UHS2_NATIVE_DCMD_DAM_IO              (1 << UHS2_NATIVE_DCMD_DAM_POS)
> > >>>>> +
> > >>>>> +/*
> > >>>>> + * Per UHS2 spec, DCMD payload should be MSB first. There may be
> > >>>>> + * two types of data be assembled to MSB:
> > >>>>> + * 1. TLEN: Input block size for single read/write and number of blocks
> > >>>>> + * for multiple read/write to calculate TLEN as MSB first per spec.
> > >>>>> + * 2. SD command argument.
> > >>>>> + */
> > >>>>> +static inline __be32 uhs2_dcmd_convert_msb(u32 input)
> > >>>>> +{
> > >>>>> +     u32 ret = 0;
> > >>>>> +
> > >>>>> +     ret = ((input & 0xFF) << 24) |
> > >>>>> +             (((input >> 8) & 0xFF) << 16) |
> > >>>>> +             (((input >> 16) & 0xFF) << 8) |
> > >>>>> +             ((input >> 24) & 0xFF);
> > >>>>> +     return cpu_to_be32(ret);
> > >>>>> +}
> > >>>>> +
> > >>>>> +#define UHS2_RES_NACK_POS    7
> > >>>>> +#define UHS2_RES_NACK_MASK   (0x1 << UHS2_RES_NACK_POS)
> > >>>>> +
> > >>>>> +#define UHS2_RES_ECODE_POS   4
> > >>>>> +#define UHS2_RES_ECODE_MASK  0x7
> > >>>>> +#define UHS2_RES_ECODE_COND  1
> > >>>>> +#define UHS2_RES_ECODE_ARG   2
> > >>>>> +#define UHS2_RES_ECODE_GEN   3
> > >>>>> +
> > >>>>> +/* IOADR of device registers */
> > >>>>> +#define UHS2_IOADR_GENERIC_CAPS              0x00
> > >>>>> +#define UHS2_IOADR_PHY_CAPS          0x02
> > >>>>> +#define UHS2_IOADR_LINK_CAPS         0x04
> > >>>>> +#define UHS2_IOADR_RSV_CAPS          0x06
> > >>>>> +#define UHS2_IOADR_GENERIC_SETTINGS  0x08
> > >>>>> +#define UHS2_IOADR_PHY_SETTINGS              0x0A
> > >>>>> +#define UHS2_IOADR_LINK_SETTINGS     0x0C
> > >>>>> +#define UHS2_IOADR_PRESET            0x40
> > >>>>> +
> > >>>>> +/* SD application packets */
> > >>>>> +#define UHS2_SD_CMD_INDEX_POS        8
> > >>>>> +
> > >>>>> +#define UHS2_SD_CMD_APP_POS  14
> > >>>>> +#define UHS2_SD_CMD_APP              (1 << UHS2_SD_CMD_APP_POS)
> > >>>>> +
> > >>>>> +/* UHS-II Device Registers */
> > >>>>> +#define UHS2_DEV_CONFIG_REG  0x000
> > >>>>> +
> > >>>>> +/* General Caps and Settings registers */
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_CAPS     (UHS2_DEV_CONFIG_REG + 0x000)
> > >>>>> +#define UHS2_DEV_CONFIG_N_LANES_POS  8
> > >>>>> +#define UHS2_DEV_CONFIG_N_LANES_MASK 0x3F
> > >>>>> +#define UHS2_DEV_CONFIG_2L_HD_FD     0x1
> > >>>>> +#define UHS2_DEV_CONFIG_2D1U_FD              0x2
> > >>>>> +#define UHS2_DEV_CONFIG_1D2U_FD              0x4
> > >>>>> +#define UHS2_DEV_CONFIG_2D2U_FD              0x8
> > >>>>> +#define UHS2_DEV_CONFIG_DADR_POS     14
> > >>>>> +#define UHS2_DEV_CONFIG_DADR_MASK    0x1
> > >>>>> +#define UHS2_DEV_CONFIG_APP_POS              16
> > >>>>> +#define UHS2_DEV_CONFIG_APP_MASK     0xFF
> > >>>>> +#define UHS2_DEV_CONFIG_APP_SD_MEM   0x1
> > >>>>> +
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_SET                      (UHS2_DEV_CONFIG_REG + 0x008)
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS  8
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD     0x0
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD              0x2
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD              0x3
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD              0x4
> > >>>>> +#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE BIT(31)
> > >>>>> +
> > >>>>> +/* PHY Caps and Settings registers */
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_CAPS     (UHS2_DEV_CONFIG_REG + 0x002)
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_MINOR_MASK       0xF
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_POS        4
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK       0x3
> > >>>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_POS        15
> > >>>>> +#define UHS2_DEV_CONFIG_CAN_HIBER_MASK       0x1
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_CAPS1    (UHS2_DEV_CONFIG_REG + 0x003)
> > >>>>> +#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK       0xF
> > >>>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_POS        4
> > >>>>> +#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK       0xF
> > >>>>> +
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_SET                      (UHS2_DEV_CONFIG_REG + 0x00A)
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS    6
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A              0x0
> > >>>>> +#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B              0x1
> > >>>>> +
> > >>>>> +/* LINK-TRAN Caps and Settings registers */
> > >>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS               (UHS2_DEV_CONFIG_REG + 0x004)
> > >>>>> +#define UHS2_DEV_CONFIG_LT_MINOR_MASK                0xF
> > >>>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_POS         4
> > >>>>> +#define UHS2_DEV_CONFIG_LT_MAJOR_MASK                0x3
> > >>>>> +#define UHS2_DEV_CONFIG_N_FCU_POS            8
> > >>>>> +#define UHS2_DEV_CONFIG_N_FCU_MASK           0xFF
> > >>>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_POS         16
> > >>>>> +#define UHS2_DEV_CONFIG_DEV_TYPE_MASK                0x7
> > >>>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS              20
> > >>>>> +#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK     0xFFF
> > >>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1              (UHS2_DEV_CONFIG_REG + 0x005)
> > >>>>> +#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK              0xFF
> > >>>>> +
> > >>>>> +#define UHS2_DEV_CONFIG_LINK_TRAN_SET                (UHS2_DEV_CONFIG_REG + 0x00C)
> > >>>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN   0x200
> > >>>>> +#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS 16
> > >>>>> +
> > >>>>> +/* Preset register */
> > >>>>> +#define UHS2_DEV_CONFIG_PRESET       (UHS2_DEV_CONFIG_REG + 0x040)
> > >>>>> +
> > >>>>> +#define UHS2_DEV_INT_REG     0x100
> > >>>>> +
> > >>>>> +#define UHS2_DEV_STATUS_REG  0x180
> > >>>>> +
> > >>>>> +#define UHS2_DEV_CMD_REG             0x200
> > >>>>> +#define UHS2_DEV_CMD_FULL_RESET              (UHS2_DEV_CMD_REG + 0x000)
> > >>>>> +#define UHS2_DEV_CMD_GO_DORMANT_STATE        (UHS2_DEV_CMD_REG + 0x001)
> > >>>>> +#define UHS2_DEV_CMD_DORMANT_HIBER   BIT(7)
> > >>>>> +#define UHS2_DEV_CMD_DEVICE_INIT     (UHS2_DEV_CMD_REG + 0x002)
> > >>>>> +#define UHS2_DEV_INIT_COMPLETE_FLAG  BIT(11)
> > >>>>> +#define UHS2_DEV_CMD_ENUMERATE               (UHS2_DEV_CMD_REG + 0x003)
> > >>>>> +#define UHS2_DEV_CMD_TRANS_ABORT     (UHS2_DEV_CMD_REG + 0x004)
> > >>>>> +
> > >>>>> +#define UHS2_RCLK_MAX        52000000
> > >>>>> +#define UHS2_RCLK_MIN        26000000
> > >>>>> +
> > >>>>> +struct sd_uhs2_wait_active_state_data {
> > >>>>> +     struct mmc_host *host;
> > >>>>> +     struct mmc_command *cmd;
> > >>>>> +};
> > >>>>> +
> > >>>>> +#endif /* LINUX_MMC_UHS2_H */
> > >>>>
> > >>>
> > >>> Thanks, Victor Shih
> > >>
> > >
> > > Best regards,
> > > Ben Chuang
> >

Thanks, Victor Shih
  

Patch

diff --git a/include/linux/mmc/card.h b/include/linux/mmc/card.h
index 4a42f31b7bb0..d638a2c689cf 100644
--- a/include/linux/mmc/card.h
+++ b/include/linux/mmc/card.h
@@ -190,6 +190,13 @@  struct sd_switch_caps {
 #define SD_MAX_CURRENT_400	(1 << SD_SET_CURRENT_LIMIT_400)
 #define SD_MAX_CURRENT_600	(1 << SD_SET_CURRENT_LIMIT_600)
 #define SD_MAX_CURRENT_800	(1 << SD_SET_CURRENT_LIMIT_800)
+	unsigned int		sd4_curr_limit;
+#define SD4_SET_POWER_LIMIT_0_72W	0
+#define SD4_SET_POWER_LIMIT_1_44W	1
+#define SD4_SET_POWER_LIMIT_2_16W	2
+#define SD4_SET_POWER_LIMIT_2_88W	3
+#define SD4_SET_POWER_LIMIT_1_80W	4
+#define SD4_SET_POWER_NO_CHANGE		(-1)
 };
 
 struct sd_ext_reg {
@@ -213,7 +220,35 @@  struct sd_ext_reg {
 
 struct sd_uhs2_config {
 	u32			node_id;
-	/* TODO: Extend with more register configs. */
+
+	u32			dap;
+	u32			gap;
+	u32			n_fcu;
+	u32			maxblk_len;
+	u8			n_lanes;
+	u8			dadr_len;
+	u8			app_type;
+	u8			phy_minor_rev;
+	u8			phy_major_rev;
+	u8			can_hibernate;
+	u8			n_lss_sync;
+	u8			n_lss_dir;
+	u8			link_minor_rev;
+	u8			link_major_rev;
+	u8			dev_type;
+	u8			n_data_gap;
+
+	u32			n_fcu_set;
+	u32			maxblk_len_set;
+	u8			n_lanes_set;
+	u8			speed_range_set;
+	u8			n_lss_sync_set;
+	u8			n_lss_dir_set;
+	u8			n_data_gap_set;
+	u8			pwrctrl_mode_set;
+	u8			max_retry_set;
+
+	u8			cfg_complete;
 };
 
 struct sdio_cccr {
@@ -323,6 +358,9 @@  struct mmc_card {
 	struct sd_ext_reg	ext_perf;	/* SD extension reg for PERF */
 
 	struct sd_uhs2_config	uhs2_config;	/* SD UHS-II config */
+	u8			uhs2_state;	/* SD UHS-II states */
+#define MMC_UHS2_INITIALIZED	BIT(1)
+#define MMC_UHS2_SPEED_B	BIT(2)
 
 	unsigned int		sdio_funcs;	/* number of SDIO functions */
 	atomic_t		sdio_funcs_probed; /* number of probed SDIO funcs */
@@ -364,4 +402,6 @@  bool mmc_card_is_blockaddr(struct mmc_card *card);
 #define mmc_card_sdio(c)	((c)->type == MMC_TYPE_SDIO)
 #define mmc_card_sd_combo(c)	((c)->type == MMC_TYPE_SD_COMBO)
 
+#define mmc_card_can_poweroff_notify(c)	((c)->ext_power.feature_support & SD_EXT_POWER_OFF_NOTIFY)
+
 #endif /* LINUX_MMC_CARD_H */
diff --git a/include/linux/mmc/core.h b/include/linux/mmc/core.h
index 6efec0b9820c..2a0581d87706 100644
--- a/include/linux/mmc/core.h
+++ b/include/linux/mmc/core.h
@@ -23,6 +23,14 @@  enum mmc_blk_status {
 	MMC_BLK_NEW_REQUEST,
 };
 
+struct uhs2_command {
+	u16	header;
+	u16	arg;
+	__be32	*payload;
+	u32	payload_len;
+	u32	packet_len;
+};
+
 struct mmc_command {
 	u32			opcode;
 	u32			arg;
@@ -109,6 +117,11 @@  struct mmc_command {
 	unsigned int		busy_timeout;	/* busy detect timeout in ms */
 	struct mmc_data		*data;		/* data segment associated with cmd */
 	struct mmc_request	*mrq;		/* associated request */
+
+	struct uhs2_command	*uhs2_cmd;	/* UHS2 command */
+	u8			*uhs2_resp;	/* UHS2 native cmd resp */
+	u8			uhs2_resp_len;	/* UHS2 native cmd resp len */
+	u8			uhs2_tmode0_flag; /* UHS2 transfer mode flag */
 };
 
 struct mmc_data {
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 895bcf7f80b7..249a9414ad10 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -16,6 +16,7 @@ 
 #include <linux/mmc/pm.h>
 #include <linux/dma-direction.h>
 #include <linux/blk-crypto-profile.h>
+#include <linux/mmc/sd_uhs2.h>
 
 struct mmc_ios {
 	unsigned int	clock;			/* clock rate */
@@ -96,7 +97,48 @@  struct mmc_clk_phase_map {
 };
 
 struct sd_uhs2_caps {
-	/* TODO: Add UHS-II capabilities for the host. */
+	u32	dap;
+	u32	gap;
+	u32	group_desc;
+	u32	maxblk_len;
+	u32	n_fcu;
+	u8	n_lanes;
+	u8	addr64;
+	u8	card_type;
+	u8	phy_rev;
+	u8	speed_range;
+	u8	can_hibernate;
+	u8	n_lss_sync;
+	u8	n_lss_dir;
+	u8	link_rev;
+	u8	host_type;
+	u8	n_data_gap;
+
+	u32	maxblk_len_set;
+	u32	n_fcu_set;
+	u8	n_lanes_set;
+	u8	n_lss_sync_set;
+	u8	n_lss_dir_set;
+	u8	n_data_gap_set;
+	u8	max_retry_set;
+};
+
+struct sd_uhs2_ios {
+	bool		is_2L_HD_mode;
+	bool		is_APP_CMD;
+	unsigned int	power_delay_ms;		/* waiting for stable power */
+};
+
+enum sd_uhs2_operation {
+	UHS2_PHY_INIT = 0,
+	UHS2_SET_CONFIG,
+	UHS2_ENABLE_INT,
+	UHS2_DISABLE_INT,
+	UHS2_ENABLE_CLK,
+	UHS2_DISABLE_CLK,
+	UHS2_CHECK_DORMANT,
+	UHS2_SET_SPEED_B,
+	UHS2_POST_ATTACH_SD,
 };
 
 struct mmc_host;
@@ -231,6 +273,20 @@  struct mmc_host_ops {
 
 	/* Initialize an SD express card, mandatory for MMC_CAP2_SD_EXP. */
 	int	(*init_sd_express)(struct mmc_host *host, struct mmc_ios *ios);
+
+	/* UHS2 interfaces */
+	int	(*uhs2_detect_init)(struct mmc_host *host);
+	int	(*uhs2_set_reg)(struct mmc_host *host, enum sd_uhs2_operation act);
+	int (*uhs2_disable_clk)(struct mmc_host *host);
+	int (*uhs2_enable_clk)(struct mmc_host *host);
+
+	/*
+	 * The uhs2_control callback is used to execute SD UHS-II specific
+	 * operations. It's mandatory to implement for hosts that supports the
+	 * SD UHS-II interface (MMC_CAP2_SD_UHS2). Expected return values are a
+	 * negative errno in case of a failure or zero for success.
+	 */
+	int	(*uhs2_control)(struct mmc_host *host, enum sd_uhs2_operation op);
 };
 
 struct mmc_cqe_ops {
@@ -323,6 +379,7 @@  struct mmc_pwrseq;
 
 struct mmc_supply {
 	struct regulator *vmmc;		/* Card power supply */
+	struct regulator *vmmc2;	/* UHS2 VDD2 power supply */
 	struct regulator *vqmmc;	/* Optional Vccq supply */
 	struct regulator *vqmmc2;	/* Optional supply for phy */
 };
@@ -344,10 +401,12 @@  struct mmc_host {
 	u32			ocr_avail_sdio;	/* SDIO-specific OCR */
 	u32			ocr_avail_sd;	/* SD-specific OCR */
 	u32			ocr_avail_mmc;	/* MMC-specific OCR */
+	u32			ocr_avail_uhs2; /* UHS2-specific OCR */
 	struct wakeup_source	*ws;		/* Enable consume of uevents */
 	u32			max_current_330;
 	u32			max_current_300;
 	u32			max_current_180;
+	u32			max_current_180_vdd2; /* UHS2 vdd2 max curt. */
 
 #define MMC_VDD_165_195		0x00000080	/* VDD voltage 1.65 - 1.95 */
 #define MMC_VDD_20_21		0x00000100	/* VDD voltage 2.0 ~ 2.1 */
@@ -366,6 +425,7 @@  struct mmc_host {
 #define MMC_VDD_33_34		0x00200000	/* VDD voltage 3.3 ~ 3.4 */
 #define MMC_VDD_34_35		0x00400000	/* VDD voltage 3.4 ~ 3.5 */
 #define MMC_VDD_35_36		0x00800000	/* VDD voltage 3.5 ~ 3.6 */
+#define MMC_VDD2_165_195	0x00000080	/* UHS2 VDD2 1.65 ~ 1.95 */
 
 	u32			caps;		/* Host capabilities */
 
@@ -443,7 +503,12 @@  struct mmc_host {
 #endif
 #define MMC_CAP2_ALT_GPT_TEGRA	(1 << 28)	/* Host with eMMC that has GPT entry at a non-standard location */
 
+	int flags;
+#define MMC_UHS2_SUPPORT	(1 << 0)
+#define MMC_UHS2_2L_HD		(1 << 2)
+
 	struct sd_uhs2_caps	uhs2_caps;	/* Host UHS-II capabilities */
+	struct sd_uhs2_ios	uhs2_ios;	/* Host UHS-II capabilities */
 
 	int			fixed_drv_type;	/* fixed driver type for non-removable media */
 
@@ -695,4 +760,7 @@  int mmc_send_tuning(struct mmc_host *host, u32 opcode, int *cmd_error);
 int mmc_send_abort_tuning(struct mmc_host *host, u32 opcode);
 int mmc_get_ext_csd(struct mmc_card *card, u8 **new_ext_csd);
 
+#define mmc_uhs2_2L_HD_mode(h)	((h)->uhs2_ios.is_2L_HD_mode)
+#define mmc_uhs2_APP_cmd(h)	((h)->uhs2_ios.is_APP_CMD)
+
 #endif /* LINUX_MMC_HOST_H */
diff --git a/include/linux/mmc/sd_uhs2.h b/include/linux/mmc/sd_uhs2.h
new file mode 100644
index 000000000000..8fcf702cf4a5
--- /dev/null
+++ b/include/linux/mmc/sd_uhs2.h
@@ -0,0 +1,263 @@ 
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Header file for UHS-II packets, Host Controller registers and I/O
+ * accessors.
+ *
+ *  Copyright (C) 2014 Intel Corp, All Rights Reserved.
+ */
+#ifndef LINUX_MMC_UHS2_H
+#define LINUX_MMC_UHS2_H
+
+/* LINK Layer definition */
+/*
+ * UHS2 Header:
+ * Refer to UHS-II Addendum Version 1.02 Figure 5-2, the format of CCMD Header is described below:
+ *      bit [3:0]  : DID(Destination ID = Node ID of UHS2 card)
+ *      bit [6:4]  : TYP(Packet Type)
+ *                   000b: CCMD(Control command packet)
+ *                   001b: DCMD(Data command packet)
+ *                   010b: RES(Response packet)
+ *                   011b: DATA(Data payload packet)
+ *                   111b: MSG(Message packet)
+ *                   Others: Reserved
+ *      bit [7]    : NP(Native Packet)
+ *      bit [10:8] : TID(Transaction ID)
+ *      bit [11]   : Reserved
+ *      bit [15:12]: SID(Source ID 0: Node ID of Host)
+ *
+ * Broadcast CCMD issued by Host is represented as DID=SID=0.
+ */
+/*
+ * UHS2 Argument:
+ * Refer to UHS-II Addendum Version 1.02 Figure 6-5, the format of CCMD Argument is described below:
+ *      bit [3:0]  : MSB of IOADR
+ *      bit [5:4]  : PLEN(Payload Length)
+ *                   00b: 0 byte
+ *                   01b: 4 bytes
+ *                   10b: 8 bytes
+ *                   11b: 16 bytes
+ *      bit [6]    : Reserved
+ *      bit [7]    : R/W(Read/Write)
+ *                   0: Control read command
+ *                   1: Control write command
+ *      bit [15:8] : LSB of IOADR
+ *
+ * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
+ * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
+ */
+#define UHS2_NATIVE_PACKET_POS	7
+#define UHS2_NATIVE_PACKET	(1 << UHS2_NATIVE_PACKET_POS)
+
+#define UHS2_PACKET_TYPE_POS	4
+#define UHS2_PACKET_TYPE_CCMD	(0 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_DCMD	(1 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_RES	(2 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_DATA	(3 << UHS2_PACKET_TYPE_POS)
+#define UHS2_PACKET_TYPE_MSG	(7 << UHS2_PACKET_TYPE_POS)
+
+#define UHS2_DEST_ID_MASK	0x0F
+#define UHS2_DEST_ID		0x1
+
+#define UHS2_SRC_ID_POS		12
+#define UHS2_SRC_ID_MASK	0xF000
+
+#define UHS2_TRANS_ID_POS	8
+#define UHS2_TRANS_ID_MASK	0x0700
+
+/* UHS2 MSG */
+#define UHS2_MSG_CTG_POS	5
+#define UHS2_MSG_CTG_LMSG	0x00
+#define UHS2_MSG_CTG_INT	0x60
+#define UHS2_MSG_CTG_AMSG	0x80
+
+#define UHS2_MSG_CTG_FCREQ	0x00
+#define UHS2_MSG_CTG_FCRDY	0x01
+#define UHS2_MSG_CTG_STAT	0x02
+
+#define UHS2_MSG_CODE_POS			8
+#define UHS2_MSG_CODE_FC_UNRECOVER_ERR		0x8
+#define UHS2_MSG_CODE_STAT_UNRECOVER_ERR	0x8
+#define UHS2_MSG_CODE_STAT_RECOVER_ERR		0x1
+
+/* TRANS Layer definition */
+
+/* Native packets*/
+#define UHS2_NATIVE_CMD_RW_POS	7
+#define UHS2_NATIVE_CMD_WRITE	(1 << UHS2_NATIVE_CMD_RW_POS)
+#define UHS2_NATIVE_CMD_READ	(0 << UHS2_NATIVE_CMD_RW_POS)
+
+#define UHS2_NATIVE_CMD_PLEN_POS	4
+#define UHS2_NATIVE_CMD_PLEN_4B		(1 << UHS2_NATIVE_CMD_PLEN_POS)
+#define UHS2_NATIVE_CMD_PLEN_8B		(2 << UHS2_NATIVE_CMD_PLEN_POS)
+#define UHS2_NATIVE_CMD_PLEN_16B	(3 << UHS2_NATIVE_CMD_PLEN_POS)
+
+#define UHS2_NATIVE_CCMD_GET_MIOADR_MASK	0xF00
+#define UHS2_NATIVE_CCMD_MIOADR_MASK		0x0F
+
+#define UHS2_NATIVE_CCMD_LIOADR_POS		8
+#define UHS2_NATIVE_CCMD_GET_LIOADR_MASK	0x0FF
+
+#define UHS2_CCMD_DEV_INIT_COMPLETE_FLAG	BIT(11)
+#define UHS2_DEV_INIT_PAYLOAD_LEN		1
+#define UHS2_DEV_INIT_RESP_LEN			6
+#define UHS2_DEV_ENUM_PAYLOAD_LEN		1
+#define UHS2_DEV_ENUM_RESP_LEN			8
+#define UHS2_CFG_WRITE_PAYLOAD_LEN		2
+#define UHS2_CFG_WRITE_PHY_SET_RESP_LEN		4
+#define UHS2_CFG_WRITE_GENERIC_SET_RESP_LEN	5
+#define UHS2_GO_DORMANT_PAYLOAD_LEN		1
+
+/*
+ * UHS2 Argument:
+ * Refer to UHS-II Addendum Version 1.02 Figure 6-8, the format of DCMD Argument is described below:
+ *      bit [3:0]  : Reserved
+ *      bit [6:3]  : TMODE(Transfer Mode)
+ *                   bit 3: DAM(Data Access Mode)
+ *                   bit 4: TLUM(TLEN Unit Mode)
+ *                   bit 5: LM(Length Mode)
+ *                   bit 6: DM(Duplex Mode)
+ *      bit [7]    : R/W(Read/Write)
+ *                   0: Control read command
+ *                   1: Control write command
+ *      bit [15:8] : Reserved
+ *
+ * I/O Address specifies the address of register in UHS-II I/O space accessed by CCMD.
+ * The unit of I/O Address is 4 Bytes. It is transmitted in MSB first, LSB last.
+ */
+#define UHS2_DCMD_DM_POS		6
+#define UHS2_DCMD_2L_HD_MODE		(1 << UHS2_DCMD_DM_POS)
+#define UHS2_DCMD_LM_POS		5
+#define UHS2_DCMD_LM_TLEN_EXIST		(1 << UHS2_DCMD_LM_POS)
+#define UHS2_DCMD_TLUM_POS		4
+#define UHS2_DCMD_TLUM_BYTE_MODE	(1 << UHS2_DCMD_TLUM_POS)
+#define UHS2_NATIVE_DCMD_DAM_POS	3
+#define UHS2_NATIVE_DCMD_DAM_IO		(1 << UHS2_NATIVE_DCMD_DAM_POS)
+
+/*
+ * Per UHS2 spec, DCMD payload should be MSB first. There may be
+ * two types of data be assembled to MSB:
+ * 1. TLEN: Input block size for single read/write and number of blocks
+ * for multiple read/write to calculate TLEN as MSB first per spec.
+ * 2. SD command argument.
+ */
+static inline __be32 uhs2_dcmd_convert_msb(u32 input)
+{
+	u32 ret = 0;
+
+	ret = ((input & 0xFF) << 24) |
+		(((input >> 8) & 0xFF) << 16) |
+		(((input >> 16) & 0xFF) << 8) |
+		((input >> 24) & 0xFF);
+	return cpu_to_be32(ret);
+}
+
+#define UHS2_RES_NACK_POS	7
+#define UHS2_RES_NACK_MASK	(0x1 << UHS2_RES_NACK_POS)
+
+#define UHS2_RES_ECODE_POS	4
+#define UHS2_RES_ECODE_MASK	0x7
+#define UHS2_RES_ECODE_COND	1
+#define UHS2_RES_ECODE_ARG	2
+#define UHS2_RES_ECODE_GEN	3
+
+/* IOADR of device registers */
+#define UHS2_IOADR_GENERIC_CAPS		0x00
+#define UHS2_IOADR_PHY_CAPS		0x02
+#define UHS2_IOADR_LINK_CAPS		0x04
+#define UHS2_IOADR_RSV_CAPS		0x06
+#define UHS2_IOADR_GENERIC_SETTINGS	0x08
+#define UHS2_IOADR_PHY_SETTINGS		0x0A
+#define UHS2_IOADR_LINK_SETTINGS	0x0C
+#define UHS2_IOADR_PRESET		0x40
+
+/* SD application packets */
+#define UHS2_SD_CMD_INDEX_POS	8
+
+#define UHS2_SD_CMD_APP_POS	14
+#define UHS2_SD_CMD_APP		(1 << UHS2_SD_CMD_APP_POS)
+
+/* UHS-II Device Registers */
+#define UHS2_DEV_CONFIG_REG	0x000
+
+/* General Caps and Settings registers */
+#define UHS2_DEV_CONFIG_GEN_CAPS	(UHS2_DEV_CONFIG_REG + 0x000)
+#define UHS2_DEV_CONFIG_N_LANES_POS	8
+#define UHS2_DEV_CONFIG_N_LANES_MASK	0x3F
+#define UHS2_DEV_CONFIG_2L_HD_FD	0x1
+#define UHS2_DEV_CONFIG_2D1U_FD		0x2
+#define UHS2_DEV_CONFIG_1D2U_FD		0x4
+#define UHS2_DEV_CONFIG_2D2U_FD		0x8
+#define UHS2_DEV_CONFIG_DADR_POS	14
+#define UHS2_DEV_CONFIG_DADR_MASK	0x1
+#define UHS2_DEV_CONFIG_APP_POS		16
+#define UHS2_DEV_CONFIG_APP_MASK	0xFF
+#define UHS2_DEV_CONFIG_APP_SD_MEM	0x1
+
+#define UHS2_DEV_CONFIG_GEN_SET			(UHS2_DEV_CONFIG_REG + 0x008)
+#define UHS2_DEV_CONFIG_GEN_SET_N_LANES_POS	8
+#define UHS2_DEV_CONFIG_GEN_SET_2L_FD_HD	0x0
+#define UHS2_DEV_CONFIG_GEN_SET_2D1U_FD		0x2
+#define UHS2_DEV_CONFIG_GEN_SET_1D2U_FD		0x3
+#define UHS2_DEV_CONFIG_GEN_SET_2D2U_FD		0x4
+#define UHS2_DEV_CONFIG_GEN_SET_CFG_COMPLETE	BIT(31)
+
+/* PHY Caps and Settings registers */
+#define UHS2_DEV_CONFIG_PHY_CAPS	(UHS2_DEV_CONFIG_REG + 0x002)
+#define UHS2_DEV_CONFIG_PHY_MINOR_MASK	0xF
+#define UHS2_DEV_CONFIG_PHY_MAJOR_POS	4
+#define UHS2_DEV_CONFIG_PHY_MAJOR_MASK	0x3
+#define UHS2_DEV_CONFIG_CAN_HIBER_POS	15
+#define UHS2_DEV_CONFIG_CAN_HIBER_MASK	0x1
+#define UHS2_DEV_CONFIG_PHY_CAPS1	(UHS2_DEV_CONFIG_REG + 0x003)
+#define UHS2_DEV_CONFIG_N_LSS_SYN_MASK	0xF
+#define UHS2_DEV_CONFIG_N_LSS_DIR_POS	4
+#define UHS2_DEV_CONFIG_N_LSS_DIR_MASK	0xF
+
+#define UHS2_DEV_CONFIG_PHY_SET			(UHS2_DEV_CONFIG_REG + 0x00A)
+#define UHS2_DEV_CONFIG_PHY_SET_SPEED_POS	6
+#define UHS2_DEV_CONFIG_PHY_SET_SPEED_A		0x0
+#define UHS2_DEV_CONFIG_PHY_SET_SPEED_B		0x1
+
+/* LINK-TRAN Caps and Settings registers */
+#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS		(UHS2_DEV_CONFIG_REG + 0x004)
+#define UHS2_DEV_CONFIG_LT_MINOR_MASK		0xF
+#define UHS2_DEV_CONFIG_LT_MAJOR_POS		4
+#define UHS2_DEV_CONFIG_LT_MAJOR_MASK		0x3
+#define UHS2_DEV_CONFIG_N_FCU_POS		8
+#define UHS2_DEV_CONFIG_N_FCU_MASK		0xFF
+#define UHS2_DEV_CONFIG_DEV_TYPE_POS		16
+#define UHS2_DEV_CONFIG_DEV_TYPE_MASK		0x7
+#define UHS2_DEV_CONFIG_MAX_BLK_LEN_POS		20
+#define UHS2_DEV_CONFIG_MAX_BLK_LEN_MASK	0xFFF
+#define UHS2_DEV_CONFIG_LINK_TRAN_CAPS1		(UHS2_DEV_CONFIG_REG + 0x005)
+#define UHS2_DEV_CONFIG_N_DATA_GAP_MASK		0xFF
+
+#define UHS2_DEV_CONFIG_LINK_TRAN_SET		(UHS2_DEV_CONFIG_REG + 0x00C)
+#define UHS2_DEV_CONFIG_LT_SET_MAX_BLK_LEN	0x200
+#define UHS2_DEV_CONFIG_LT_SET_MAX_RETRY_POS	16
+
+/* Preset register */
+#define UHS2_DEV_CONFIG_PRESET	(UHS2_DEV_CONFIG_REG + 0x040)
+
+#define UHS2_DEV_INT_REG	0x100
+
+#define UHS2_DEV_STATUS_REG	0x180
+
+#define UHS2_DEV_CMD_REG		0x200
+#define UHS2_DEV_CMD_FULL_RESET		(UHS2_DEV_CMD_REG + 0x000)
+#define UHS2_DEV_CMD_GO_DORMANT_STATE	(UHS2_DEV_CMD_REG + 0x001)
+#define UHS2_DEV_CMD_DORMANT_HIBER	BIT(7)
+#define UHS2_DEV_CMD_DEVICE_INIT	(UHS2_DEV_CMD_REG + 0x002)
+#define UHS2_DEV_INIT_COMPLETE_FLAG	BIT(11)
+#define UHS2_DEV_CMD_ENUMERATE		(UHS2_DEV_CMD_REG + 0x003)
+#define UHS2_DEV_CMD_TRANS_ABORT	(UHS2_DEV_CMD_REG + 0x004)
+
+#define UHS2_RCLK_MAX	52000000
+#define UHS2_RCLK_MIN	26000000
+
+struct sd_uhs2_wait_active_state_data {
+	struct mmc_host *host;
+	struct mmc_command *cmd;
+};
+
+#endif /* LINUX_MMC_UHS2_H */