[v9,2/2] arm64: dts: qcom: add SA8540P ride(Qdrive-3)

Message ID 20221116154932.17127-3-quic_ppareek@quicinc.com
State New
Headers
Series arm64: dts: qcom: add dts for sa8540p-ride board |

Commit Message

Parikshit Pareek Nov. 16, 2022, 3:49 p.m. UTC
  Introduce the Qualcomm SA8540P ride automotive platform, also known as
Qdrive-3 development board.

This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
regulators, debug UART, PMICs, remoteprocs and USB.

The SA8540P ride contains four PM8450 PMICs. A separate DTSI file has
been created for PMIC, so that it can be used for future SA8540P based
boards.

Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Tested-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Tested-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Eric Chanudet <echanude@redhat.com>
---
 arch/arm64/boot/dts/qcom/Makefile         |   1 +
 arch/arm64/boot/dts/qcom/pm8450a.dtsi     |  77 ++++++++
 arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 219 ++++++++++++++++++++++
 3 files changed, 297 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/pm8450a.dtsi
 create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-ride.dts
  

Comments

Johan Hovold Nov. 16, 2022, 3:59 p.m. UTC | #1
On Wed, Nov 16, 2022 at 09:19:32PM +0530, Parikshit Pareek wrote:
> Introduce the Qualcomm SA8540P ride automotive platform, also known as
> Qdrive-3 development board.
> 
> This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
> regulators, debug UART, PMICs, remoteprocs and USB.
> 
> The SA8540P ride contains four PM8450 PMICs. A separate DTSI file has
> been created for PMIC, so that it can be used for future SA8540P based
> boards.
> 
> Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
> Tested-by: Brian Masney <bmasney@redhat.com>
> Reviewed-by: Brian Masney <bmasney@redhat.com>
> Tested-by: Eric Chanudet <echanude@redhat.com>
> Reviewed-by: Eric Chanudet <echanude@redhat.com>

Looks good to me now:

Reviewed-by: Johan Hovold <johan+linaro@kernel.org>

Johan
  
Konrad Dybcio Nov. 16, 2022, 4:01 p.m. UTC | #2
On 16/11/2022 16:49, Parikshit Pareek wrote:
> Introduce the Qualcomm SA8540P ride automotive platform, also known as
> Qdrive-3 development board.
> 
> This initial contribution supports SMP, CPUFreq, cluster idle, UFS, RPMh
> regulators, debug UART, PMICs, remoteprocs and USB.
> 
> The SA8540P ride contains four PM8450 PMICs. A separate DTSI file has
> been created for PMIC, so that it can be used for future SA8540P based
> boards.
> 
> Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
> Tested-by: Brian Masney <bmasney@redhat.com>
> Reviewed-by: Brian Masney <bmasney@redhat.com>
> Tested-by: Eric Chanudet <echanude@redhat.com>
> Reviewed-by: Eric Chanudet <echanude@redhat.com>
> ---
>   arch/arm64/boot/dts/qcom/Makefile         |   1 +
>   arch/arm64/boot/dts/qcom/pm8450a.dtsi     |  77 ++++++++
>   arch/arm64/boot/dts/qcom/sa8540p-ride.dts | 219 ++++++++++++++++++++++
>   3 files changed, 297 insertions(+)
>   create mode 100644 arch/arm64/boot/dts/qcom/pm8450a.dtsi
>   create mode 100644 arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index afe496a93f94..87a681f15643 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -56,6 +56,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
> diff --git a/arch/arm64/boot/dts/qcom/pm8450a.dtsi b/arch/arm64/boot/dts/qcom/pm8450a.dtsi
> new file mode 100644
> index 000000000000..34fc72896761
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/pm8450a.dtsi
> @@ -0,0 +1,77 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +#include <dt-bindings/spmi/spmi.h>
> +
> +&spmi_bus {
> +	pm8450a: pmic@0 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x0 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450a_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450a_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pm8450c: pmic@4 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x4 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450c_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450c_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pm8450e: pmic@8 {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0x8 SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450e_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450e_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +
> +	pm8450g: pmic@c {
> +		compatible = "qcom,pm8150", "qcom,spmi-pmic";
> +		reg = <0xc SPMI_USID>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pm8450g_gpios: gpio@c000 {
> +			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
> +			reg = <0xc000>;
> +			gpio-controller;
> +			gpio-ranges = <&pm8450g_gpios 0 0 10>;
> +			#gpio-cells = <2>;
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> new file mode 100644
> index 000000000000..5262a7cc7fcd
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
> @@ -0,0 +1,219 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Linaro Limited
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
> +#include "sa8540p.dtsi"
> +#include "pm8450a.dtsi"
> +
> +/ {
> +	model = "Qualcomm SA8540P Ride";
> +	compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
> +
> +	aliases {
> +		serial0 = &qup2_uart17;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +};
> +
> +&apps_rsc {
> +	regulators-0 {
> +		compatible = "qcom,pm8150-rpmh-regulators";
> +		qcom,pmic-id = "a";
> +
> +		vreg_l3a: ldo3 {
> +			regulator-name = "vreg_l3a";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1208000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l5a: ldo5 {
> +			regulator-name = "vreg_l5a";
> +			regulator-min-microvolt = <912000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7a: ldo7 {
> +			regulator-name = "vreg_l7a";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l13a: ldo13 {
> +			regulator-name = "vreg_l13a";
> +			regulator-min-microvolt = <3072000>;
> +			regulator-max-microvolt = <3072000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-1 {
> +		compatible = "qcom,pm8150-rpmh-regulators";
> +		qcom,pmic-id = "c";
> +
> +		vreg_l1c: ldo1 {
> +			regulator-name = "vreg_l1c";
> +			regulator-min-microvolt = <912000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2c: ldo2 {
> +			regulator-name = "vreg_l2c";
> +			regulator-min-microvolt = <3072000>;
> +			regulator-max-microvolt = <3072000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l4c: ldo4 {
> +			regulator-name = "vreg_l4c";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1208000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6c: ldo6 {
> +			regulator-name = "vreg_l6c";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l7c: ldo7 {
> +			regulator-name = "vreg_l7c";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l17c: ldo17 {
> +			regulator-name = "vreg_l17c";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2504000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +		};
> +	};
> +
> +	regulators-2 {
> +		compatible = "qcom,pm8150-rpmh-regulators";
> +		qcom,pmic-id = "g";
> +
> +		vreg_l3g: ldo3 {
> +			regulator-name = "vreg_l3g";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7g: ldo7 {
> +			regulator-name = "vreg_l7g";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8g: ldo8 {
> +			regulator-name = "vreg_l8g";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <880000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +};
> +
> +&qup2 {
> +	status = "okay";
> +};
> +
> +&qup2_uart17 {
> +	compatible = "qcom,geni-debug-uart";
> +	status = "okay";
> +};
> +
> +&remoteproc_nsp0 {
> +	firmware-name = "qcom/sa8540p/cdsp.mbn";
> +	status = "okay";
> +};
> +
> +&remoteproc_nsp1 {
> +	firmware-name = "qcom/sa8540p/cdsp1.mbn";
> +	status = "okay";
> +};
> +
> +&ufs_mem_hc {
> +	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
> +
> +	vcc-supply = <&vreg_l17c>;
> +	vcc-max-microamp = <800000>;
These -microamp properties do not exist upstream.

With that fixed:

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
> +	vccq-supply = <&vreg_l6c>;
> +	vccq-max-microamp = <900000>;
> +
> +	status = "okay";
> +};
> +
> +&ufs_mem_phy {
> +	vdda-phy-supply = <&vreg_l8g>;
> +	vdda-pll-supply = <&vreg_l3g>;
> +
> +	status = "okay";
> +};
> +
> +&usb_0 {
> +	status = "okay";
> +};
> +
> +&usb_0_dwc3 {
> +	dr_mode = "peripheral";
> +};
> +
> +&usb_0_hsphy {
> +	vdda-pll-supply = <&vreg_l5a>;
> +	vdda18-supply = <&vreg_l7a>;
> +	vdda33-supply = <&vreg_l13a>;
> +
> +	status = "okay";
> +};
> +
> +&usb_0_qmpphy {
> +	vdda-phy-supply = <&vreg_l3a>;
> +	vdda-pll-supply = <&vreg_l5a>;
> +
> +	status = "okay";
> +};
> +
> +&usb_2_hsphy0 {
> +	vdda-pll-supply = <&vreg_l5a>;
> +	vdda18-supply = <&vreg_l7g>;
> +	vdda33-supply = <&vreg_l13a>;
> +
> +	status = "okay";
> +};
> +
> +&usb_2_qmpphy0 {
> +	vdda-phy-supply = <&vreg_l3a>;
> +	vdda-pll-supply = <&vreg_l5a>;
> +
> +	status = "okay";
> +};
> +
> +&xo_board_clk {
> +	clock-frequency = <38400000>;
> +};
  

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index afe496a93f94..87a681f15643 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -56,6 +56,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
diff --git a/arch/arm64/boot/dts/qcom/pm8450a.dtsi b/arch/arm64/boot/dts/qcom/pm8450a.dtsi
new file mode 100644
index 000000000000..34fc72896761
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8450a.dtsi
@@ -0,0 +1,77 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pm8450a: pmic@0 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450a_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450a_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450c: pmic@4 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450c_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450c_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450e: pmic@8 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450e_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450e_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450g: pmic@c {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0xc SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450g_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450g_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sa8540p-ride.dts b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
new file mode 100644
index 000000000000..5262a7cc7fcd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8540p-ride.dts
@@ -0,0 +1,219 @@ 
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sa8540p.dtsi"
+#include "pm8450a.dtsi"
+
+/ {
+	model = "Qualcomm SA8540P Ride";
+	compatible = "qcom,sa8540p-ride", "qcom,sa8540p";
+
+	aliases {
+		serial0 = &qup2_uart17;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_l3a: ldo3 {
+			regulator-name = "vreg_l3a";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-name = "vreg_l5a";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-name = "vreg_l7a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a: ldo13 {
+			regulator-name = "vreg_l13a";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c: ldo2 {
+			regulator-name = "vreg_l2c";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c: ldo4 {
+			regulator-name = "vreg_l4c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c: ldo6 {
+			regulator-name = "vreg_l6c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17c: ldo17 {
+			regulator-name = "vreg_l17c";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vreg_l3g: ldo3 {
+			regulator-name = "vreg_l3g";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7g: ldo7 {
+			regulator-name = "vreg_l7g";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8g: ldo8 {
+			regulator-name = "vreg_l8g";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&qup2 {
+	status = "okay";
+};
+
+&qup2_uart17 {
+	compatible = "qcom,geni-debug-uart";
+	status = "okay";
+};
+
+&remoteproc_nsp0 {
+	firmware-name = "qcom/sa8540p/cdsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_nsp1 {
+	firmware-name = "qcom/sa8540p/cdsp1.mbn";
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17c>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l6c>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l8g>;
+	vdda-pll-supply = <&vreg_l3g>;
+
+	status = "okay";
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7a>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy0 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <38400000>;
+};