diff mbox series

[RFC,v3,6/6] ARM: pxa: Convert gumstix Bluetooth to GPIO descriptors

Message ID 20230929-pxa-gpio-v3-6-af8d5e5d1f34@skole.hr
State New
Headers
Series ARM: pxa: GPIO descriptor conversions |

Commit Message

Duje Mihanović Sept. 29, 2023, 1:14 p.m. UTC 
  Gumstix still uses the legacy GPIO interface for resetting the Bluetooth
device.

Convert it to use the GPIO descriptor interface.

Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
---
 arch/arm/mach-pxa/gumstix.c | 24 +++++++++++++-----------
 1 file changed, 13 insertions(+), 11 deletions(-)

Comments

Linus Walleij Sept. 29, 2023, 9:48 p.m. UTC | #1 
On Fri, Sep 29, 2023 at 3:15 PM Duje Mihanović <duje.mihanovic@skole.hr> wrote:

> Gumstix still uses the legacy GPIO interface for resetting the Bluetooth
> device.
>
> Convert it to use the GPIO descriptor interface.
>
> Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>

As far as I can tell the BT UART is registered before the
gpios are added and retrieved, and that should work so:
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
diff mbox series

Patch

diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index c9f0f62187bd..14e1b9274d7a 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -20,8 +20,8 @@ 
 #include <linux/delay.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/partitions.h>
+#include <linux/gpio/consumer.h>
 #include <linux/gpio/machine.h>
-#include <linux/gpio.h>
 #include <linux/err.h>
 #include <linux/clk.h>
 
@@ -129,6 +129,9 @@  static void gumstix_udc_init(void)
 #endif
 
 #ifdef CONFIG_BT
+GPIO_LOOKUP_SINGLE(gumstix_bt_gpio_table, "pxa2xx-uart.1", "pxa-gpio",
+		GPIO_GUMSTIX_BTRESET, "BTRST", GPIO_ACTIVE_LOW);
+
 /* Normally, the bootloader would have enabled this 32kHz clock but many
 ** boards still have u-boot 1.1.4 so we check if it has been turned on and
 ** if not, we turn it on with a warning message. */
@@ -153,24 +156,23 @@  static void gumstix_setup_bt_clock(void)
 
 static void __init gumstix_bluetooth_init(void)
 {
-	int err;
+	struct gpio_desc *desc;
+
+	gpiod_add_lookup_table(&gumstix_bt_gpio_table);
 
 	gumstix_setup_bt_clock();
 
-	err = gpio_request(GPIO_GUMSTIX_BTRESET, "BTRST");
-	if (err) {
+	desc = gpiod_get(&pxa_device_btuart.dev, "BTRST", GPIOD_OUT_HIGH);
+	if (IS_ERR(desc)) {
 		pr_err("gumstix: failed request gpio for bluetooth reset\n");
 		return;
 	}
 
-	err = gpio_direction_output(GPIO_GUMSTIX_BTRESET, 1);
-	if (err) {
-		pr_err("gumstix: can't reset bluetooth\n");
-		return;
-	}
-	gpio_set_value(GPIO_GUMSTIX_BTRESET, 0);
+	gpiod_set_value(desc, 0);
 	udelay(100);
-	gpio_set_value(GPIO_GUMSTIX_BTRESET, 1);
+	gpiod_set_value(desc, 1);
+
+	gpiod_put(desc);
 }
 #else
 static void gumstix_bluetooth_init(void)