diff mbox series

arm64: dts: bitmain: lowercase unit addresses

Message ID 20230712074611.35952-1-krzysztof.kozlowski@linaro.org
State New
Headers
Series arm64: dts: bitmain: lowercase unit addresses |

Commit Message

Krzysztof Kozlowski July 12, 2023, 7:46 a.m. UTC 
  Unit addresses are expected to be lower case.  Pointed also by W=1
builds:

  Warning (simple_bus_reg): /soc/serial@5801A000: simple-bus unit address format error, expected "5801a000"

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 arch/arm64/boot/dts/bitmain/bm1880.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

Comments

Krzysztof Kozlowski Sept. 24, 2023, 7:02 p.m. UTC | #1 
On Wed, 12 Jul 2023 09:46:11 +0200, Krzysztof Kozlowski wrote:
> Unit addresses are expected to be lower case.  Pointed also by W=1
> builds:
> 
>   Warning (simple_bus_reg): /soc/serial@5801A000: simple-bus unit address format error, expected "5801a000"
> 
> 

Patches were waiting long enough on the lists. I assume there are no objections,
at least none were shared, and this just slipped through the cracks. I applied
to my tree for further soc pull request, but if anyone wants to take it
instead, let me know.

Applied, thanks!

[1/1] arm64: dts: bitmain: lowercase unit addresses
      https://git.kernel.org/krzk/linux-dt/c/0b137caaaab462debb1cd342cdc0df307e301bfc

Best regards,
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/bitmain/bm1880.dtsi b/arch/arm64/boot/dts/bitmain/bm1880.dtsi
index 53a9b76057aa..22a200fb07d2 100644
--- a/arch/arm64/boot/dts/bitmain/bm1880.dtsi
+++ b/arch/arm64/boot/dts/bitmain/bm1880.dtsi
@@ -184,7 +184,7 @@  uart0: serial@58018000 {
 			status = "disabled";
 		};
 
-		uart1: serial@5801A000 {
+		uart1: serial@5801a000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x0 0x5801a000 0x0 0x2000>;
 			clocks = <&clk BM1880_CLK_UART_500M>,
@@ -197,7 +197,7 @@  uart1: serial@5801A000 {
 			status = "disabled";
 		};
 
-		uart2: serial@5801C000 {
+		uart2: serial@5801c000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x0 0x5801c000 0x0 0x2000>;
 			clocks = <&clk BM1880_CLK_UART_500M>,
@@ -210,7 +210,7 @@  uart2: serial@5801C000 {
 			status = "disabled";
 		};
 
-		uart3: serial@5801E000 {
+		uart3: serial@5801e000 {
 			compatible = "snps,dw-apb-uart";
 			reg = <0x0 0x5801e000 0x0 0x2000>;
 			clocks = <&clk BM1880_CLK_UART_500M>,