[v4,3/6] arm64: dts: ti: k3-am62x-sk-common: Add HDMI support
Commit Message
The DSS outputs DPI signals via its second video port (VP2). The DPI
output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
transmitter (SIL9022) on the board.
Add pinmux info for DSS DPI output.
Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
on the AM625 SK and AM62-LP SK platforms.
Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
and the output of HDMI TX to the input of the HDMI connector.
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
---
.../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 93 +++++++++++++++++++
1 file changed, 93 insertions(+)
Comments
On 07/08/23 21:03, Aradhya Bhatia wrote:
> The DSS outputs DPI signals via its second video port (VP2). The DPI
> output from DSS is 24 bits (RGB888) and is forwarded to an HDMI
> transmitter (SIL9022) on the board.
>
> Add pinmux info for DSS DPI output.
>
> Add DT nodes for SIL9022 HDMI transmitter (TX), and the HDMI connector
> on the AM625 SK and AM62-LP SK platforms.
>
> Additionally, connect the output of DSS (VP2) with input of the HDMI TX,
> and the output of HDMI TX to the input of the HDMI connector.
>
> Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
> ---
> .../arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 93 +++++++++++++++++++
> 1 file changed, 93 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
> index 540ed8a0d7fb..edbe5295373b 100644
> --- a/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi
> @@ -114,6 +114,17 @@ sound_master: simple-audio-card,codec {
> clocks = <&tlv320_mclk>;
> };
> };
> +
> + hdmi0: connector-hdmi {
> + compatible = "hdmi-connector";
> + label = "hdmi";
> + type = "a";
> + port {
> + hdmi_connector_in: endpoint {
> + remote-endpoint = <&sii9022_out>;
> + };
> + };
> + };
> };
>
> &main_pmx0 {
> @@ -226,6 +237,39 @@ AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25/J17) GPMC0_WEN.MCASP1_AXR0 */
> AM62X_IOPAD(0x084, PIN_INPUT, 2) /* (L23/K20) GPMC0_ADVN_ALE.MCASP1_AXR2 */
> >;
> };
> +
> + main_dss0_pins_default: main-dss0-default-pins {
> + pinctrl-single,pins = <
> + AM62X_IOPAD(0x0100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
> + AM62X_IOPAD(0x00f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
> + AM62X_IOPAD(0x0104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
> + AM62X_IOPAD(0x00fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
> + AM62X_IOPAD(0x00b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
> + AM62X_IOPAD(0x00bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
> + AM62X_IOPAD(0x00c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
> + AM62X_IOPAD(0x00c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
> + AM62X_IOPAD(0x00c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
> + AM62X_IOPAD(0x00cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
> + AM62X_IOPAD(0x00d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
> + AM62X_IOPAD(0x00d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
> + AM62X_IOPAD(0x00d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
> + AM62X_IOPAD(0x00dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
> + AM62X_IOPAD(0x00e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
> + AM62X_IOPAD(0x00e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
> + AM62X_IOPAD(0x00e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
> + AM62X_IOPAD(0x00ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */
> + AM62X_IOPAD(0x00f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
> + AM62X_IOPAD(0x00f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
> + AM62X_IOPAD(0x005c, PIN_OUTPUT, 1) /* (R24) GPMC0_AD8.VOUT0_DATA16 */
> + AM62X_IOPAD(0x0060, PIN_OUTPUT, 1) /* (R25) GPMC0_AD9.VOUT0_DATA17 */
> + AM62X_IOPAD(0x0064, PIN_OUTPUT, 1) /* (T25) GPMC0_AD10.VOUT0_DATA18 */
> + AM62X_IOPAD(0x0068, PIN_OUTPUT, 1) /* (R21) GPMC0_AD11.VOUT0_DATA19 */
> + AM62X_IOPAD(0x006c, PIN_OUTPUT, 1) /* (T22) GPMC0_AD12.VOUT0_DATA20 */
> + AM62X_IOPAD(0x0070, PIN_OUTPUT, 1) /* (T24) GPMC0_AD13.VOUT0_DATA21 */
> + AM62X_IOPAD(0x0074, PIN_OUTPUT, 1) /* (U25) GPMC0_AD14.VOUT0_DATA22 */
> + AM62X_IOPAD(0x0078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */
Rest of the pinmux in the file uses padding of 3. Here you are using
padding of 4. Consistency would be good.
> + >;
> + };
> };
>
> &mcu_pmx0 {
> @@ -313,6 +357,38 @@ tlv320aic3106: audio-codec@1b {
> IOVDD-supply = <&vcc_3v3_sys>;
> DRVDD-supply = <&vcc_3v3_sys>;
> };
> +
> + sii9022: bridge-hdmi@3b {
> + compatible = "sil,sii9022";
> + reg = <0x3b>;
> +
Line break not needed.
> + interrupt-parent = <&exp1>;
> + interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
> +
Same.
> + #sound-dai-cells = <0>;
> + sil,i2s-data-lanes = < 0 >;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + sii9022_in: endpoint {
> + remote-endpoint = <&dpi1_out>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + sii9022_out: endpoint {
> + remote-endpoint = <&hdmi_connector_in>;
> + };
> + };
> + };
> + };
> };
>
> &sdhci0 {
> @@ -410,3 +486,20 @@ &mcasp1 {
> tx-num-evt = <32>;
> rx-num-evt = <32>;
> };
> +
> +&dss {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&main_dss0_pins_default>;
> +};
> +
> +&dss_ports {
> + /* VP2: DPI Output */
> + port@1 {
> + reg = <1>;
> +
> + dpi1_out: endpoint {
> + remote-endpoint = <&sii9022_in>;
> + };
> + };
> +};
@@ -114,6 +114,17 @@ sound_master: simple-audio-card,codec {
clocks = <&tlv320_mclk>;
};
};
+
+ hdmi0: connector-hdmi {
+ compatible = "hdmi-connector";
+ label = "hdmi";
+ type = "a";
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&sii9022_out>;
+ };
+ };
+ };
};
&main_pmx0 {
@@ -226,6 +237,39 @@ AM62X_IOPAD(0x08c, PIN_OUTPUT, 2) /* (L25/J17) GPMC0_WEN.MCASP1_AXR0 */
AM62X_IOPAD(0x084, PIN_INPUT, 2) /* (L23/K20) GPMC0_ADVN_ALE.MCASP1_AXR2 */
>;
};
+
+ main_dss0_pins_default: main-dss0-default-pins {
+ pinctrl-single,pins = <
+ AM62X_IOPAD(0x0100, PIN_OUTPUT, 0) /* (AC25) VOUT0_VSYNC */
+ AM62X_IOPAD(0x00f8, PIN_OUTPUT, 0) /* (AB24) VOUT0_HSYNC */
+ AM62X_IOPAD(0x0104, PIN_OUTPUT, 0) /* (AC24) VOUT0_PCLK */
+ AM62X_IOPAD(0x00fc, PIN_OUTPUT, 0) /* (Y20) VOUT0_DE */
+ AM62X_IOPAD(0x00b8, PIN_OUTPUT, 0) /* (U22) VOUT0_DATA0 */
+ AM62X_IOPAD(0x00bc, PIN_OUTPUT, 0) /* (V24) VOUT0_DATA1 */
+ AM62X_IOPAD(0x00c0, PIN_OUTPUT, 0) /* (W25) VOUT0_DATA2 */
+ AM62X_IOPAD(0x00c4, PIN_OUTPUT, 0) /* (W24) VOUT0_DATA3 */
+ AM62X_IOPAD(0x00c8, PIN_OUTPUT, 0) /* (Y25) VOUT0_DATA4 */
+ AM62X_IOPAD(0x00cc, PIN_OUTPUT, 0) /* (Y24) VOUT0_DATA5 */
+ AM62X_IOPAD(0x00d0, PIN_OUTPUT, 0) /* (Y23) VOUT0_DATA6 */
+ AM62X_IOPAD(0x00d4, PIN_OUTPUT, 0) /* (AA25) VOUT0_DATA7 */
+ AM62X_IOPAD(0x00d8, PIN_OUTPUT, 0) /* (V21) VOUT0_DATA8 */
+ AM62X_IOPAD(0x00dc, PIN_OUTPUT, 0) /* (W21) VOUT0_DATA9 */
+ AM62X_IOPAD(0x00e0, PIN_OUTPUT, 0) /* (V20) VOUT0_DATA10 */
+ AM62X_IOPAD(0x00e4, PIN_OUTPUT, 0) /* (AA23) VOUT0_DATA11 */
+ AM62X_IOPAD(0x00e8, PIN_OUTPUT, 0) /* (AB25) VOUT0_DATA12 */
+ AM62X_IOPAD(0x00ec, PIN_OUTPUT, 0) /* (AA24) VOUT0_DATA13 */
+ AM62X_IOPAD(0x00f0, PIN_OUTPUT, 0) /* (Y22) VOUT0_DATA14 */
+ AM62X_IOPAD(0x00f4, PIN_OUTPUT, 0) /* (AA21) VOUT0_DATA15 */
+ AM62X_IOPAD(0x005c, PIN_OUTPUT, 1) /* (R24) GPMC0_AD8.VOUT0_DATA16 */
+ AM62X_IOPAD(0x0060, PIN_OUTPUT, 1) /* (R25) GPMC0_AD9.VOUT0_DATA17 */
+ AM62X_IOPAD(0x0064, PIN_OUTPUT, 1) /* (T25) GPMC0_AD10.VOUT0_DATA18 */
+ AM62X_IOPAD(0x0068, PIN_OUTPUT, 1) /* (R21) GPMC0_AD11.VOUT0_DATA19 */
+ AM62X_IOPAD(0x006c, PIN_OUTPUT, 1) /* (T22) GPMC0_AD12.VOUT0_DATA20 */
+ AM62X_IOPAD(0x0070, PIN_OUTPUT, 1) /* (T24) GPMC0_AD13.VOUT0_DATA21 */
+ AM62X_IOPAD(0x0074, PIN_OUTPUT, 1) /* (U25) GPMC0_AD14.VOUT0_DATA22 */
+ AM62X_IOPAD(0x0078, PIN_OUTPUT, 1) /* (U24) GPMC0_AD15.VOUT0_DATA23 */
+ >;
+ };
};
&mcu_pmx0 {
@@ -313,6 +357,38 @@ tlv320aic3106: audio-codec@1b {
IOVDD-supply = <&vcc_3v3_sys>;
DRVDD-supply = <&vcc_3v3_sys>;
};
+
+ sii9022: bridge-hdmi@3b {
+ compatible = "sil,sii9022";
+ reg = <0x3b>;
+
+ interrupt-parent = <&exp1>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+
+ #sound-dai-cells = <0>;
+ sil,i2s-data-lanes = < 0 >;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ sii9022_in: endpoint {
+ remote-endpoint = <&dpi1_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ sii9022_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+ };
+ };
+ };
};
&sdhci0 {
@@ -410,3 +486,20 @@ &mcasp1 {
tx-num-evt = <32>;
rx-num-evt = <32>;
};
+
+&dss {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_dss0_pins_default>;
+};
+
+&dss_ports {
+ /* VP2: DPI Output */
+ port@1 {
+ reg = <1>;
+
+ dpi1_out: endpoint {
+ remote-endpoint = <&sii9022_in>;
+ };
+ };
+};