[linux-next-v1,1/3] arm64: dts: rockchip: Fix gmac phy mode to rgmii on Rock 3A sbc

Message ID 20221111094238.1640-1-linux.amoon@gmail.com
State New
Headers
Series [linux-next-v1,1/3] arm64: dts: rockchip: Fix gmac phy mode to rgmii on Rock 3A sbc |

Commit Message

Anand Moon Nov. 11, 2022, 9:42 a.m. UTC
  On rk356x ethernet phy support reduced media independent interface (RMII)
and reduced gigabit media independent interface (RGMII).
So set the phy mode to rgmii.

Signed-off-by: Anand Moon <linux.amoon@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)
  

Comments

Michael Riesch Nov. 11, 2022, 11:52 a.m. UTC | #1
Hi Anand,

On 11/11/22 10:42, Anand Moon wrote:
> On rk356x ethernet phy support reduced media independent interface (RMII)
> and reduced gigabit media independent interface (RGMII).
> So set the phy mode to rgmii.
> 
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> index ea74ba32fbbd..72e410e3aca8 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> @@ -253,7 +253,7 @@ &gmac1 {
>  	assigned-clock-rates = <0>, <125000000>;
>  	clock_in_out = "output";
>  	phy-handle = <&rgmii_phy1>;
> -	phy-mode = "rgmii-id";
> +	phy-mode = "rgmii";

What are you trying to fix here? If it ain't broken, don't fix it. I
would assume if you switch from rgmii-id to rgmii you need to adjust the
rx/tx-delays, otherwise this change does not make sense to me. Feel free
to point out what I am missing, though.

Best regards,
Michael

>  	pinctrl-names = "default";
>  	pinctrl-0 = <&gmac1m1_miim
>  		     &gmac1m1_tx_bus2
  
Peter Geis Nov. 11, 2022, 12:56 p.m. UTC | #2
On Fri, Nov 11, 2022 at 4:43 AM Anand Moon <linux.amoon@gmail.com> wrote:
>
> On rk356x ethernet phy support reduced media independent interface (RMII)
> and reduced gigabit media independent interface (RGMII).
> So set the phy mode to rgmii.

The RTL8211 supports rgmii-id just fine, you only need to go to rgmii
on these boards if you need to tune the delays manually.

>
> Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> index ea74ba32fbbd..72e410e3aca8 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> @@ -253,7 +253,7 @@ &gmac1 {
>         assigned-clock-rates = <0>, <125000000>;
>         clock_in_out = "output";
>         phy-handle = <&rgmii_phy1>;
> -       phy-mode = "rgmii-id";
> +       phy-mode = "rgmii";

You should be setting the delay tuning in this patch as well.

>         pinctrl-names = "default";
>         pinctrl-0 = <&gmac1m1_miim
>                      &gmac1m1_tx_bus2
> --
> 2.38.1
>
>
> _______________________________________________
> Linux-rockchip mailing list
> Linux-rockchip@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-rockchip
  
Anand Moon Nov. 16, 2022, 6:11 p.m. UTC | #3
Hi Petter / Michael.

Thanks for your review comments.

On Fri, 11 Nov 2022 at 18:26, Peter Geis <pgwipeout@gmail.com> wrote:
>
> On Fri, Nov 11, 2022 at 4:43 AM Anand Moon <linux.amoon@gmail.com> wrote:
> >
> > On rk356x ethernet phy support reduced media independent interface (RMII)
> > and reduced gigabit media independent interface (RGMII).
> > So set the phy mode to rgmii.
>
> The RTL8211 supports rgmii-id just fine, you only need to go to rgmii
> on these boards if you need to tune the delays manually.

Ok rgmii supports internal rx and tx clock delay
whereas rgmii-id does not supports internal clock delay.

>
> >
> > Signed-off-by: Anand Moon <linux.amoon@gmail.com>
> > ---
> >  arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> > index ea74ba32fbbd..72e410e3aca8 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> > +++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
> > @@ -253,7 +253,7 @@ &gmac1 {
> >         assigned-clock-rates = <0>, <125000000>;
> >         clock_in_out = "output";
> >         phy-handle = <&rgmii_phy1>;
> > -       phy-mode = "rgmii-id";
> > +       phy-mode = "rgmii";
>
> You should be setting the delay tuning in this patch as well.

I will try to fix this in the next version.

>
> >         pinctrl-names = "default";
> >         pinctrl-0 = <&gmac1m1_miim
> >                      &gmac1m1_tx_bus2
> > --
> > 2.38.1
Thanks


-Anand
  

Patch

diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
index ea74ba32fbbd..72e410e3aca8 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -253,7 +253,7 @@  &gmac1 {
 	assigned-clock-rates = <0>, <125000000>;
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy1>;
-	phy-mode = "rgmii-id";
+	phy-mode = "rgmii";
 	pinctrl-names = "default";
 	pinctrl-0 = <&gmac1m1_miim
 		     &gmac1m1_tx_bus2