dt-bindings: gpio: brcm,kona-gpio: convert to YAML
Commit Message
Convert Broadcom Kona family GPIO controller bindings to DT schema.
Changes during conversion:
- add used, but previously undocumented SoC-specific compatibles
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
---
Changes since RFC:
- fix interrupts maxItems
- narrow interrupts min/maxItems per each variant
- thanks for the feedback Linus, Krzysztof :)
.../bindings/gpio/brcm,kona-gpio.txt | 52 ---------
.../bindings/gpio/brcm,kona-gpio.yaml | 100 ++++++++++++++++++
MAINTAINERS | 2 +-
3 files changed, 101 insertions(+), 53 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
create mode 100644 Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
Comments
On 30/07/2023 17:23, Stanislav Jakubek wrote:
> Convert Broadcom Kona family GPIO controller bindings to DT schema.
>
> Changes during conversion:
> - add used, but previously undocumented SoC-specific compatibles
>
> Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
> ---
> Changes since RFC:
> - fix interrupts maxItems
> - narrow interrupts min/maxItems per each variant
> - thanks for the feedback Linus, Krzysztof :)
For the future
RFC is v1, so this should be v2. And it matters, because:
b4 diff '<ZMaAdG9Zj9AL1NiR@standask-GA-A55M-S2HP>'
ERROR: Could not auto-find previous revision
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
On Sun, Jul 30, 2023 at 5:23 PM Stanislav Jakubek
<stano.jakubek@gmail.com> wrote:
>
> Convert Broadcom Kona family GPIO controller bindings to DT schema.
>
> Changes during conversion:
> - add used, but previously undocumented SoC-specific compatibles
>
> Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Applied, thanks!
Bartosz
deleted file mode 100644
@@ -1,52 +0,0 @@
-Broadcom Kona Family GPIO
-=========================
-
-This GPIO driver is used in the following Broadcom SoCs:
- BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
-
-The Broadcom GPIO Controller IP can be configured prior to synthesis to
-support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
-GPIO controller only supports edge, not level, triggering of interrupts.
-
-Required properties
--------------------
-
-- compatible: "brcm,bcm11351-gpio", "brcm,kona-gpio"
-- reg: Physical base address and length of the controller's registers.
-- interrupts: The interrupt outputs from the controller. There is one GPIO
- interrupt per GPIO bank. The number of interrupts listed depends on the
- number of GPIO banks on the SoC. The interrupts must be ordered by bank,
- starting with bank 0. There is always a 1:1 mapping between banks and
- IRQs.
-- #gpio-cells: Should be <2>. The first cell is the pin number, the second
- cell is used to specify optional parameters:
- - bit 0 specifies polarity (0 for normal, 1 for inverted)
- See also "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
-- #interrupt-cells: Should be <2>. The first cell is the GPIO number. The
- second cell is used to specify flags. The following subset of flags is
- supported:
- - trigger type (bits[1:0]):
- 1 = low-to-high edge triggered.
- 2 = high-to-low edge triggered.
- 3 = low-to-high or high-to-low edge triggered
- Valid values are 1, 2, 3
- See also .../devicetree/bindings/interrupt-controller/interrupts.txt.
-- gpio-controller: Marks the device node as a GPIO controller.
-- interrupt-controller: Marks the device node as an interrupt controller.
-
-Example:
- gpio: gpio@35003000 {
- compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
- reg = <0x35003000 0x800>;
- interrupts =
- <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH
- GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
- #gpio-cells = <2>;
- #interrupt-cells = <2>;
- gpio-controller;
- interrupt-controller;
- };
new file mode 100644
@@ -0,0 +1,100 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/brcm,kona-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom Kona family GPIO controller
+
+description:
+ The Broadcom GPIO Controller IP can be configured prior to synthesis to
+ support up to 8 banks of 32 GPIOs where each bank has its own IRQ. The
+ GPIO controller only supports edge, not level, triggering of interrupts.
+
+maintainers:
+ - Ray Jui <rjui@broadcom.com>
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - brcm,bcm11351-gpio
+ - brcm,bcm21664-gpio
+ - brcm,bcm23550-gpio
+ - const: brcm,kona-gpio
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ minItems: 4
+ maxItems: 6
+ description:
+ The interrupt outputs from the controller. There is one GPIO interrupt
+ per GPIO bank. The number of interrupts listed depends on the number of
+ GPIO banks on the SoC. The interrupts must be ordered by bank, starting
+ with bank 0. There is always a 1:1 mapping between banks and IRQs.
+
+ '#gpio-cells':
+ const: 2
+
+ '#interrupt-cells':
+ const: 2
+
+ gpio-controller: true
+
+ interrupt-controller: true
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - '#gpio-cells'
+ - '#interrupt-cells'
+ - gpio-controller
+ - interrupt-controller
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: brcm,bcm11351-gpio
+ then:
+ properties:
+ interrupts:
+ minItems: 6
+ - if:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - brcm,bcm21664-gpio
+ - brcm,bcm23550-gpio
+ then:
+ properties:
+ interrupts:
+ maxItems: 4
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ gpio@35003000 {
+ compatible = "brcm,bcm11351-gpio", "brcm,kona-gpio";
+ reg = <0x35003000 0x800>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ #gpio-cells = <2>;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ interrupt-controller;
+ };
+...
@@ -4221,7 +4221,7 @@ BROADCOM KONA GPIO DRIVER
M: Ray Jui <rjui@broadcom.com>
R: Broadcom internal kernel review list <bcm-kernel-feedback-list@broadcom.com>
S: Supported
-F: Documentation/devicetree/bindings/gpio/brcm,kona-gpio.txt
+F: Documentation/devicetree/bindings/gpio/brcm,kona-gpio.yaml
F: drivers/gpio/gpio-bcm-kona.c
BROADCOM MPI3 STORAGE CONTROLLER DRIVER