[v3,tty-next,1/3] 8250: microchip: pci1xxxx: Add driver for quad-uart support.

Message ID 20221107124517.1364484-2-kumaravel.thiagarajan@microchip.com
State New
Headers
Series 8250: microchip: pci1xxxx: Add driver for the pci1xxxx's quad-uart function |

Commit Message

Kumaravel Thiagarajan Nov. 7, 2022, 12:45 p.m. UTC
  pci1xxxx is a PCIe switch with a multi-function endpoint on one of
its downstream ports. Quad-uart is one of the functions in the
multi-function endpoint. This driver loads for the quad-uart and
enumerates single or multiple instances of uart based on the PCIe
subsystem device ID.

Signed-off-by: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Signed-off-by: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
---
Changes in v3:
- Used NSEC_PER_SEC, HZ_PER_MHZ, FIELD_PREP, FIELD_GET MACROs wherever
  necessary
- Handled failure case of serial8250_register_8250_port properly
- Moved pci_setup_port to 8250_pcilib.c

Changes in v2:
- Use only the 62.5 MHz for baud clock.
- Define custom implementation for get_divisor and set_divisor.
- Use BOTHER instead of UPF_SPD_CUST for non standard baud rates
  (untested).
- Correct indentation in clock divisor computation.
- Remove unnecessary call to pci_save_state in probe function.
- Fix null pointer dereference in probe function.
- Move pci1xxxx_rs485_config to a separate patch.
- Depends on SERIAL_8250_PCI & default to SERIAL_8250.
- Change PORT_MCHP16550A to 100 from 124.
---
 MAINTAINERS                             |   7 +
 drivers/tty/serial/8250/8250_pci.c      |  24 +-
 drivers/tty/serial/8250/8250_pci1xxxx.c | 370 ++++++++++++++++++++++++
 drivers/tty/serial/8250/8250_pcilib.c   |  31 ++
 drivers/tty/serial/8250/8250_pcilib.h   |   5 +
 drivers/tty/serial/8250/8250_port.c     |   8 +
 drivers/tty/serial/8250/Kconfig         |  15 +
 drivers/tty/serial/8250/Makefile        |   2 +
 include/uapi/linux/serial_core.h        |   3 +
 9 files changed, 443 insertions(+), 22 deletions(-)
 create mode 100644 drivers/tty/serial/8250/8250_pci1xxxx.c
 create mode 100644 drivers/tty/serial/8250/8250_pcilib.c
 create mode 100644 drivers/tty/serial/8250/8250_pcilib.h
  

Comments

Greg KH Nov. 9, 2022, 12:01 p.m. UTC | #1
On Mon, Nov 07, 2022 at 06:15:15PM +0530, Kumaravel Thiagarajan wrote:
> +++ b/drivers/tty/serial/8250/8250_pcilib.c
> @@ -0,0 +1,31 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/* Microchip pci1xxxx 8250 library. */

Better name and a copyright line?

> +
> +#include <linux/pci.h>
> +#include "8250.h"
> +
> +int pci_setup_port(struct pci_dev *dev, struct uart_8250_port *port,
> +		   u8 bar, unsigned int offset, int regshift)
> +{
> +	if (bar >= PCI_STD_NUM_BARS)
> +		return -EINVAL;
> +
> +	if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
> +		if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev))
> +			return -ENOMEM;
> +
> +		port->port.iotype = UPIO_MEM;
> +		port->port.iobase = 0;
> +		port->port.mapbase = pci_resource_start(dev, bar) + offset;
> +		port->port.membase = pcim_iomap_table(dev)[bar] + offset;
> +		port->port.regshift = regshift;
> +	} else {
> +		port->port.iotype = UPIO_PORT;
> +		port->port.iobase = pci_resource_start(dev, bar) + offset;
> +		port->port.mapbase = 0;
> +		port->port.membase = NULL;
> +		port->port.regshift = 0;
> +	}
> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(pci_setup_port);

This needs a better name, 8250_pci_setup_port()?  This is not a pci core
function.

thanks,

greg k-h
  
Kumaravel Thiagarajan Nov. 10, 2022, 5:18 p.m. UTC | #2
> -----Original Message-----
> From: Greg KH <gregkh@linuxfoundation.org>
> Sent: Wednesday, November 9, 2022 5:31 PM
> To: Kumaravel Thiagarajan - I21417 <Kumaravel.Thiagarajan@microchip.com>
> Subject: Re: [PATCH v3 tty-next 1/3] 8250: microchip: pci1xxxx: Add driver for
> quad-uart support.
>  
> On Mon, Nov 07, 2022 at 06:15:15PM +0530, Kumaravel Thiagarajan wrote:
> > +++ b/drivers/tty/serial/8250/8250_pcilib.c
> > @@ -0,0 +1,31 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* Microchip pci1xxxx 8250 library. */
> 
> Better name and a copyright line?
Yes Greg. I think "8250 PCI library" would be the correct name. Is that fine?
Regarding the copyright, we moved the "setup_port" function from 8250_pci.c to this new file.
Can I use the same copyright statement from 8250_pci.c "Copyright (C) 2001 Russell King, All Rights Reserved."?

> 
> > +
> > +#include <linux/pci.h>
> > +#include "8250.h"
> > +
> > +int pci_setup_port(struct pci_dev *dev, struct uart_8250_port *port,
> > +                u8 bar, unsigned int offset, int regshift) {
> > +     if (bar >= PCI_STD_NUM_BARS)
> > +             return -EINVAL;
> > +
> > +     if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
> > +             if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev))
> > +                     return -ENOMEM;
> > +
> > +             port->port.iotype = UPIO_MEM;
> > +             port->port.iobase = 0;
> > +             port->port.mapbase = pci_resource_start(dev, bar) + offset;
> > +             port->port.membase = pcim_iomap_table(dev)[bar] + offset;
> > +             port->port.regshift = regshift;
> > +     } else {
> > +             port->port.iotype = UPIO_PORT;
> > +             port->port.iobase = pci_resource_start(dev, bar) + offset;
> > +             port->port.mapbase = 0;
> > +             port->port.membase = NULL;
> > +             port->port.regshift = 0;
> > +     }
> > +     return 0;
> > +}
> > +EXPORT_SYMBOL_GPL(pci_setup_port);
> 
> This needs a better name, 8250_pci_setup_port()?  This is not a pci core
> function.
Yes. I will rename as you mentioned.

Thank You.

Regards,
Kumar
  
Greg KH Nov. 10, 2022, 6:06 p.m. UTC | #3
On Thu, Nov 10, 2022 at 05:18:46PM +0000, Kumaravel.Thiagarajan@microchip.com wrote:
> > -----Original Message-----
> > From: Greg KH <gregkh@linuxfoundation.org>
> > Sent: Wednesday, November 9, 2022 5:31 PM
> > To: Kumaravel Thiagarajan - I21417 <Kumaravel.Thiagarajan@microchip.com>
> > Subject: Re: [PATCH v3 tty-next 1/3] 8250: microchip: pci1xxxx: Add driver for
> > quad-uart support.
> >  
> > On Mon, Nov 07, 2022 at 06:15:15PM +0530, Kumaravel Thiagarajan wrote:
> > > +++ b/drivers/tty/serial/8250/8250_pcilib.c
> > > @@ -0,0 +1,31 @@
> > > +// SPDX-License-Identifier: GPL-2.0
> > > +/* Microchip pci1xxxx 8250 library. */
> > 
> > Better name and a copyright line?
> Yes Greg. I think "8250 PCI library" would be the correct name. Is that fine?

That would be good as obviously it's not a microchip-only thing here.

> Regarding the copyright, we moved the "setup_port" function from 8250_pci.c to this new file.
> Can I use the same copyright statement from 8250_pci.c "Copyright (C) 2001 Russell King, All Rights Reserved."?

Yes, that would be good.

thanks,

greg k-h
  

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index d30f26e07cd3..aa98deaba249 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -13434,6 +13434,13 @@  F:	Documentation/devicetree/bindings/nvmem/microchip,sama7g5-otpc.yaml
 F:	drivers/nvmem/microchip-otpc.c
 F:	include/dt-bindings/nvmem/microchip,sama7g5-otpc.h
 
+MICROCHIP PCIe UART DRIVER
+M:	Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
+M:	Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
+L:	linux-serial@vger.kernel.org
+S:	Maintained
+F:	drivers/tty/serial/8250/8250_pci1xxxx.c
+
 MICROCHIP PWM DRIVER
 M:	Claudiu Beznea <claudiu.beznea@microchip.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 6f66dc2ebacc..e7023f1b9b2c 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -24,6 +24,7 @@ 
 #include <asm/io.h>
 
 #include "8250.h"
+#include "8250_pcilib.h"
 
 /*
  * init function returns:
@@ -89,28 +90,7 @@  static int
 setup_port(struct serial_private *priv, struct uart_8250_port *port,
 	   u8 bar, unsigned int offset, int regshift)
 {
-	struct pci_dev *dev = priv->dev;
-
-	if (bar >= PCI_STD_NUM_BARS)
-		return -EINVAL;
-
-	if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
-		if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev))
-			return -ENOMEM;
-
-		port->port.iotype = UPIO_MEM;
-		port->port.iobase = 0;
-		port->port.mapbase = pci_resource_start(dev, bar) + offset;
-		port->port.membase = pcim_iomap_table(dev)[bar] + offset;
-		port->port.regshift = regshift;
-	} else {
-		port->port.iotype = UPIO_PORT;
-		port->port.iobase = pci_resource_start(dev, bar) + offset;
-		port->port.mapbase = 0;
-		port->port.membase = NULL;
-		port->port.regshift = 0;
-	}
-	return 0;
+	return pci_setup_port(priv->dev, port, bar, offset, regshift);
 }
 
 /*
diff --git a/drivers/tty/serial/8250/8250_pci1xxxx.c b/drivers/tty/serial/8250/8250_pci1xxxx.c
new file mode 100644
index 000000000000..e74e8d63daee
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_pci1xxxx.c
@@ -0,0 +1,370 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Probe module for 8250/16550-type MCHP PCI serial ports.
+ *
+ *  Based on drivers/tty/serial/8250/8250_pci.c,
+ *
+ *  Copyright (C) 2022 Microchip Technology Inc., All Rights Reserved.
+ */
+
+#include <asm/byteorder.h>
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/serial_core.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/units.h>
+#include <linux/tty.h>
+
+#include "8250.h"
+#include "8250_pcilib.h"
+
+#define PCI_DEVICE_ID_EFAR_PCI12000 0xa002
+#define PCI_DEVICE_ID_EFAR_PCI11010 0xa012
+#define PCI_DEVICE_ID_EFAR_PCI11101 0xa022
+#define PCI_DEVICE_ID_EFAR_PCI11400 0xa032
+#define PCI_DEVICE_ID_EFAR_PCI11414 0xa042
+
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_4p 0x0001
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p012 0x0002
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p013 0x0003
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p023 0x0004
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p123 0x0005
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p01 0x0006
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p02 0x0007
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p03 0x0008
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p12 0x0009
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p13 0x000a
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p23 0x000b
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p0 0x000c
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p1 0x000d
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p2 0x000e
+#define PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p3 0x000f
+
+#define PCI_SUBDEVICE_ID_EFAR_PCI12000 0xa002
+#define PCI_SUBDEVICE_ID_EFAR_PCI11010 0xa012
+#define PCI_SUBDEVICE_ID_EFAR_PCI11101 0xa022
+#define PCI_SUBDEVICE_ID_EFAR_PCI11400 0xa032
+#define PCI_SUBDEVICE_ID_EFAR_PCI11414 0xa042
+
+#define UART_ACTV_REG 0x11
+#define UART_BLOCK_SET_ACTIVE BIT(0)
+
+#define UART_PCI_CTRL_REG 0x80
+#define UART_PCI_CTRL_SET_MULTIPLE_MSI BIT(4)
+#define UART_PCI_CTRL_D3_CLK_ENABLE BIT(0)
+
+#define ADCL_CFG_REG 0x40
+#define ADCL_CFG_POL_SEL BIT(2)
+#define ADCL_CFG_PIN_SEL BIT(1)
+#define ADCL_CFG_EN BIT(0)
+
+#define UART_BIT_SAMPLE_CNT 16
+#define BAUD_CLOCK_DIV_INT_MSK GENMASK(31, 8)
+#define ADCL_CFG_RTS_DELAY_MASK GENMASK(11, 8)
+#define UART_CLOCK_DEFAULT (62.5 * HZ_PER_MHZ)
+
+#define UART_WAKE_REG 0x8C
+#define UART_WAKE_MASK_REG 0x90
+#define UART_WAKE_N_PIN BIT(2)
+#define UART_WAKE_NCTS BIT(1)
+#define UART_WAKE_INT BIT(0)
+#define UART_WAKE_SRCS (UART_WAKE_N_PIN | UART_WAKE_NCTS | UART_WAKE_INT)
+
+#define UART_BAUD_CLK_DIVISOR_REG 0x54
+
+#define UART_RESET_REG 0x94
+#define UART_RESET_D3_RESET_DISABLE BIT(16)
+
+struct pci1xxxx_8250 {
+	struct pci_dev *dev;
+	unsigned int nr;
+	void __iomem *membase;
+	int line[];
+};
+
+static int pci1xxxx_get_num_ports(struct pci_dev *dev)
+{
+	switch (dev->subsystem_device) {
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p01:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p02:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p03:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p12:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p13:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p23:
+		return 2;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p012:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p123:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p013:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p023:
+		return 3;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_4p:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11414:
+		return 4;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p0:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p1:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p2:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p3:
+	default:
+		return 1;
+	}
+}
+
+static unsigned int pci1xxxx_get_divisor(struct uart_port *port,
+					 unsigned int baud, unsigned int *frac)
+{
+	unsigned int quot;
+
+	/*
+	 * Calculate baud rate sampling period in nanoseconds.
+	 * Fractional part x denotes x/255 parts of a nanosecond.
+	 */
+	quot = (NSEC_PER_SEC / (baud * UART_BIT_SAMPLE_CNT));
+	*frac = (((NSEC_PER_SEC - (quot * baud * UART_BIT_SAMPLE_CNT)) /
+		  UART_BIT_SAMPLE_CNT) * 255) / baud;
+
+	return quot;
+}
+
+static void pci1xxxx_set_divisor(struct uart_port *port, unsigned int baud,
+				 unsigned int quot, unsigned int frac)
+{
+	writel(FIELD_PREP(BAUD_CLOCK_DIV_INT_MSK, quot) | frac,
+	       port->membase + UART_BAUD_CLK_DIVISOR_REG);
+}
+
+static int pci1xxxx_setup(struct pci1xxxx_8250 *priv,
+			  struct uart_8250_port *port, int idx)
+{
+	int first_offset;
+	int offset;
+	int ret;
+
+	switch (priv->dev->subsystem_device) {
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p1:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p12:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p123:
+		first_offset = 256;
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p2:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p23:
+		first_offset = 512;
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p3:
+		first_offset = 768;
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p02:
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p023:
+		if (idx > 0)
+			idx++;
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p03:
+		if (idx > 0)
+			idx += 2;
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p13:
+		first_offset = 256;
+		if (idx > 0)
+			idx++;
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p013:
+		if (idx > 1)
+			idx++;
+		break;
+	default:
+		first_offset = 0;
+		break;
+	}
+
+	offset = first_offset + idx * 256;
+	port->port.flags |= UPF_FIXED_TYPE | UPF_SKIP_TEST;
+	port->port.type = PORT_MCHP16550A;
+	port->port.set_termios = serial8250_do_set_termios;
+	port->port.get_divisor = pci1xxxx_get_divisor;
+	port->port.set_divisor = pci1xxxx_set_divisor;
+	ret = pci_setup_port(priv->dev, port, 0, offset, 0);
+	if (ret < 0)
+		return ret;
+
+	writeb(UART_BLOCK_SET_ACTIVE, port->port.membase + UART_ACTV_REG);
+	writeb(UART_WAKE_SRCS, port->port.membase + UART_WAKE_REG);
+	writeb(UART_WAKE_N_PIN, port->port.membase + UART_WAKE_MASK_REG);
+
+	return 0;
+}
+
+static void pci1xxxx_irq_assign(struct pci1xxxx_8250 *priv,
+				struct uart_8250_port *uart, int idx)
+{
+	switch (priv->dev->subsystem_device) {
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p1:
+		uart->port.irq = pci_irq_vector(priv->dev, 1);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p2:
+		uart->port.irq = pci_irq_vector(priv->dev, 2);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p3:
+		uart->port.irq = pci_irq_vector(priv->dev, 3);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p01:
+		uart->port.irq = pci_irq_vector(priv->dev, idx);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p02:
+		if (idx > 0)
+			idx++;
+		uart->port.irq = pci_irq_vector(priv->dev, idx);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p03:
+		if (idx > 0)
+			idx += 2;
+		uart->port.irq = pci_irq_vector(priv->dev, idx);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p12:
+		uart->port.irq = pci_irq_vector(priv->dev, idx + 1);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p13:
+		if (idx > 0)
+			idx += 1;
+		uart->port.irq = pci_irq_vector(priv->dev, idx + 1);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_2p23:
+		uart->port.irq = pci_irq_vector(priv->dev, idx + 2);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p012:
+		uart->port.irq = pci_irq_vector(priv->dev, idx);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p013:
+		if (idx > 1)
+			idx++;
+		uart->port.irq = pci_irq_vector(priv->dev, idx);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p023:
+		if (idx > 0)
+			idx++;
+		uart->port.irq = pci_irq_vector(priv->dev, idx);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_3p123:
+		uart->port.irq = pci_irq_vector(priv->dev, idx + 1);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_4p:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11414:
+		uart->port.irq = pci_irq_vector(priv->dev, idx);
+		break;
+	case PCI_SUBDEVICE_ID_EFAR_PCI1XXXX_1p0:
+	case PCI_SUBDEVICE_ID_EFAR_PCI12000:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11010:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11101:
+	case PCI_SUBDEVICE_ID_EFAR_PCI11400:
+	default:
+		uart->port.irq = pci_irq_vector(priv->dev, 0);
+		break;
+	}
+}
+
+static int pci1xxxx_serial_probe(struct pci_dev *dev,
+				 const struct pci_device_id *ent)
+{
+	unsigned int nr_ports, i, j;
+	struct pci1xxxx_8250 *priv;
+	struct uart_8250_port uart;
+	int num_vectors = 0;
+	int rc;
+
+	rc = pcim_enable_device(dev);
+	if (rc)
+		return rc;
+
+	nr_ports = pci1xxxx_get_num_ports(dev);
+
+	priv = devm_kzalloc(&dev->dev, struct_size(priv, line, nr_ports),
+			    GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->membase = pcim_iomap(dev, 0, 0);
+	priv->dev = dev;
+	priv->nr = nr_ports;
+	pci_set_master(dev);
+
+	num_vectors = pci_alloc_irq_vectors(dev, 1, 4, PCI_IRQ_ALL_TYPES);
+	if (num_vectors < 0)
+		return num_vectors;
+
+	memset(&uart, 0, sizeof(uart));
+	uart.port.flags = UPF_SHARE_IRQ | UPF_FIXED_PORT;
+	uart.port.uartclk = UART_CLOCK_DEFAULT;
+	uart.port.dev = &dev->dev;
+
+	if (num_vectors == 4)
+		writeb(UART_PCI_CTRL_SET_MULTIPLE_MSI,
+		       priv->membase + UART_PCI_CTRL_REG);
+	else
+		uart.port.irq = pci_irq_vector(dev, 0);
+
+	for (i = 0; i < nr_ports; i++) {
+		if (num_vectors == 4)
+			pci1xxxx_irq_assign(priv, &uart, i);
+
+		priv->line[i] = -ENOSPC;
+		rc = pci1xxxx_setup(priv, &uart, i);
+		if (rc) {
+			dev_err(&dev->dev, "Failed to setup port %u\n", i);
+			break;
+		}
+		priv->line[i] = serial8250_register_8250_port(&uart);
+
+		if (priv->line[i] < 0) {
+			for (j = i + 1; j < nr_ports; j++)
+				priv->line[j] = -ENOSPC;
+
+			dev_err(&dev->dev,
+				"Couldn't register serial port %lx, irq %d, type %d, error %d\n",
+				uart.port.iobase, uart.port.irq,
+				uart.port.iotype, priv->line[i]);
+			break;
+		}
+	}
+
+	pci_set_drvdata(dev, priv);
+
+	return 0;
+}
+
+static void pci1xxxx_serial_remove(struct pci_dev *dev)
+{
+	struct pci1xxxx_8250 *priv = pci_get_drvdata(dev);
+	int i;
+
+	for (i = 0; i < priv->nr; i++) {
+		if (priv->line[i] >= 0)
+			serial8250_unregister_port(priv->line[i]);
+	}
+}
+
+static const struct pci_device_id pci1xxxx_pci_tbl[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_PCI11010) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_PCI11101) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_PCI11400) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_PCI11414) },
+	{ PCI_DEVICE(PCI_VENDOR_ID_EFAR, PCI_DEVICE_ID_EFAR_PCI12000) },
+	{}
+};
+MODULE_DEVICE_TABLE(pci, pci1xxxx_pci_tbl);
+
+static struct pci_driver pci1xxxx_pci_driver = {
+	.name = "pci1xxxx serial",
+	.probe = pci1xxxx_serial_probe,
+	.remove = pci1xxxx_serial_remove,
+	.id_table = pci1xxxx_pci_tbl,
+};
+
+module_pci_driver(pci1xxxx_pci_driver);
+
+MODULE_DESCRIPTION("Microchip Technology Inc. PCIe to UART module");
+MODULE_AUTHOR("Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>");
+MODULE_AUTHOR("Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/8250_pcilib.c b/drivers/tty/serial/8250/8250_pcilib.c
new file mode 100644
index 000000000000..07040781b43f
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_pcilib.c
@@ -0,0 +1,31 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/* Microchip pci1xxxx 8250 library. */
+
+#include <linux/pci.h>
+#include "8250.h"
+
+int pci_setup_port(struct pci_dev *dev, struct uart_8250_port *port,
+		   u8 bar, unsigned int offset, int regshift)
+{
+	if (bar >= PCI_STD_NUM_BARS)
+		return -EINVAL;
+
+	if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
+		if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev))
+			return -ENOMEM;
+
+		port->port.iotype = UPIO_MEM;
+		port->port.iobase = 0;
+		port->port.mapbase = pci_resource_start(dev, bar) + offset;
+		port->port.membase = pcim_iomap_table(dev)[bar] + offset;
+		port->port.regshift = regshift;
+	} else {
+		port->port.iotype = UPIO_PORT;
+		port->port.iobase = pci_resource_start(dev, bar) + offset;
+		port->port.mapbase = 0;
+		port->port.membase = NULL;
+		port->port.regshift = 0;
+	}
+	return 0;
+}
+EXPORT_SYMBOL_GPL(pci_setup_port);
diff --git a/drivers/tty/serial/8250/8250_pcilib.h b/drivers/tty/serial/8250/8250_pcilib.h
new file mode 100644
index 000000000000..c33b7eb44222
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_pcilib.h
@@ -0,0 +1,5 @@ 
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Microchip pci1xxxx 8250 library header file. */
+
+int pci_setup_port(struct pci_dev *dev, struct uart_8250_port *port, u8 bar,
+		   unsigned int offset, int regshift);
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 1d2a43214b48..ec2fe5fd7b02 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -313,6 +313,14 @@  static const struct serial8250_config uart_config[] = {
 		.rxtrig_bytes	= {1, 4, 8, 14},
 		.flags		= UART_CAP_FIFO,
 	},
+	[PORT_MCHP16550A] = {
+		.name           = "MCHP16550A",
+		.fifo_size      = 256,
+		.tx_loadsz      = 256,
+		.fcr            = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01,
+		.rxtrig_bytes   = {2, 66, 130, 194},
+		.flags          = UART_CAP_FIFO,
+	},
 };
 
 /* Uart divisor latch read */
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index d0b49e15fbf5..f67542470eae 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -132,6 +132,7 @@  config SERIAL_8250_DMA
 config SERIAL_8250_PCI
 	tristate "8250/16550 PCI device support"
 	depends on SERIAL_8250 && PCI
+	select SERIAL_8250_PCILIB
 	default SERIAL_8250
 	help
 	  This builds standard PCI serial support. You may be able to
@@ -291,6 +292,17 @@  config SERIAL_8250_HUB6
 	  To compile this driver as a module, choose M here: the module
 	  will be called 8250_hub6.
 
+config SERIAL_8250_PCI1XXXX
+	tristate "Microchip 8250 based serial port"
+	depends on SERIAL_8250_PCI
+	select SERIAL_8250_PCILIB
+	default SERIAL_8250
+	help
+	 Select this option if you have a setup with Microchip PCIe
+	 Switch with serial port enabled and wish to enable 8250
+	 serial driver for the serial interface. This driver support
+	 will ensure to support baud rates upto 1.5Mpbs.
+
 #
 # Misc. options/drivers.
 #
@@ -500,6 +512,9 @@  config SERIAL_8250_MID
 	  Intel Medfield SOC and various other Intel platforms that is not
 	  covered by the more generic SERIAL_8250_PCI option.
 
+config SERIAL_8250_PCILIB
+	bool
+
 config SERIAL_8250_PERICOM
 	tristate "Support for Pericom and Acces I/O serial ports"
 	default SERIAL_8250
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index bee908f99ea0..98202fdf39f8 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -12,6 +12,7 @@  obj-$(CONFIG_SERIAL_8250)		+= 8250.o 8250_base.o
 8250_base-$(CONFIG_SERIAL_8250_DMA)	+= 8250_dma.o
 8250_base-$(CONFIG_SERIAL_8250_DWLIB)	+= 8250_dwlib.o
 8250_base-$(CONFIG_SERIAL_8250_FINTEK)	+= 8250_fintek.o
+8250_base-$(CONFIG_SERIAL_8250_PCILIB)	+= 8250_pcilib.o
 obj-$(CONFIG_SERIAL_8250_GSC)		+= 8250_gsc.o
 obj-$(CONFIG_SERIAL_8250_PCI)		+= 8250_pci.o
 obj-$(CONFIG_SERIAL_8250_EXAR)		+= 8250_exar.o
@@ -26,6 +27,7 @@  obj-$(CONFIG_SERIAL_8250_ACCENT)	+= 8250_accent.o
 obj-$(CONFIG_SERIAL_8250_BOCA)		+= 8250_boca.o
 obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554)	+= 8250_exar_st16c554.o
 obj-$(CONFIG_SERIAL_8250_HUB6)		+= 8250_hub6.o
+obj-$(CONFIG_SERIAL_8250_PCI1XXXX)	+= 8250_pci1xxxx.o
 obj-$(CONFIG_SERIAL_8250_FSL)		+= 8250_fsl.o
 obj-$(CONFIG_SERIAL_8250_MEN_MCB)	+= 8250_men_mcb.o
 obj-$(CONFIG_SERIAL_8250_DW)		+= 8250_dw.o
diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h
index 3ba34d8378bd..281fa286555c 100644
--- a/include/uapi/linux/serial_core.h
+++ b/include/uapi/linux/serial_core.h
@@ -207,6 +207,9 @@ 
 /* Atheros AR933X SoC */
 #define PORT_AR933X	99
 
+/* MCHP 16550A UART with 256 byte FIFOs */
+#define PORT_MCHP16550A	100
+
 /* ARC (Synopsys) on-chip UART */
 #define PORT_ARC       101