[1/2] dt-bindings: pinctrl: qcom,ipq8074: convert to dtschema

  Convert Qualcomm IPQ8074 pin controller bindings to DT schema.  Keep the
parsing of pin configuration subnodes consistent with other Qualcomm
schemas (children named with '-state' suffix, their children with
'-pins').

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
 .../bindings/pinctrl/qcom,ipq8074-pinctrl.txt | 181 ------------------
 .../pinctrl/qcom,ipq8074-pinctrl.yaml         | 135 +++++++++++++
 2 files changed, 135 insertions(+), 181 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt
 create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml
  

On Tue, Nov 8, 2022 at 3:24 PM Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:

> Convert Qualcomm IPQ8074 pin controller bindings to DT schema.  Keep the
> parsing of pin configuration subnodes consistent with other Qualcomm
> schemas (children named with '-state' suffix, their children with
> '-pins').
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

Yours,
Linus Walleij
  

On Tue, Nov 08, 2022 at 03:23:56PM +0100, Krzysztof Kozlowski wrote:
> Convert Qualcomm IPQ8074 pin controller bindings to DT schema.  Keep the
> parsing of pin configuration subnodes consistent with other Qualcomm
> schemas (children named with '-state' suffix, their children with
> '-pins').
> 

Reviewed-by: Bjorn Andersson <andersson@kernel.org>

Regards,
Bjorn

> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
>  .../bindings/pinctrl/qcom,ipq8074-pinctrl.txt | 181 ------------------
>  .../pinctrl/qcom,ipq8074-pinctrl.yaml         | 135 +++++++++++++
>  2 files changed, 135 insertions(+), 181 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt
> deleted file mode 100644
> index 7b151894f5a0..000000000000
> --- a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.txt
> +++ /dev/null
> @@ -1,181 +0,0 @@
> -Qualcomm Technologies, Inc. IPQ8074 TLMM block
> -
> -This binding describes the Top Level Mode Multiplexer block found in the
> -IPQ8074 platform.
> -
> -- compatible:
> -	Usage: required
> -	Value type: <string>
> -	Definition: must be "qcom,ipq8074-pinctrl"
> -
> -- reg:
> -	Usage: required
> -	Value type: <prop-encoded-array>
> -	Definition: the base address and size of the TLMM register space.
> -
> -- interrupts:
> -	Usage: required
> -	Value type: <prop-encoded-array>
> -	Definition: should specify the TLMM summary IRQ.
> -
> -- interrupt-controller:
> -	Usage: required
> -	Value type: <none>
> -	Definition: identifies this node as an interrupt controller
> -
> -- #interrupt-cells:
> -	Usage: required
> -	Value type: <u32>
> -	Definition: must be 2. Specifying the pin number and flags, as defined
> -		    in <dt-bindings/interrupt-controller/irq.h>
> -
> -- gpio-controller:
> -	Usage: required
> -	Value type: <none>
> -	Definition: identifies this node as a gpio controller
> -
> -- #gpio-cells:
> -	Usage: required
> -	Value type: <u32>
> -	Definition: must be 2. Specifying the pin number and flags, as defined
> -		    in <dt-bindings/gpio/gpio.h>
> -
> -- gpio-ranges:
> -	Usage: required
> -	Definition:  see ../gpio/gpio.txt
> -
> -- gpio-reserved-ranges:
> -	Usage: optional
> -	Definition: see ../gpio/gpio.txt
> -
> -Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for
> -a general description of GPIO and interrupt bindings.
> -
> -Please refer to pinctrl-bindings.txt in this directory for details of the
> -common pinctrl bindings used by client devices, including the meaning of the
> -phrase "pin configuration node".
> -
> -The pin configuration nodes act as a container for an arbitrary number of
> -subnodes. Each of these subnodes represents some desired configuration for a
> -pin, a group, or a list of pins or groups. This configuration can include the
> -mux function to select on those pin(s)/group(s), and various pin configuration
> -parameters, such as pull-up, drive strength, etc.
> -
> -
> -PIN CONFIGURATION NODES:
> -
> -The name of each subnode is not important; all subnodes should be enumerated
> -and processed purely based on their content.
> -
> -Each subnode only affects those parameters that are explicitly listed. In
> -other words, a subnode that lists a mux function but no pin configuration
> -parameters implies no information about any pin configuration parameters.
> -Similarly, a pin subnode that describes a pullup parameter implies no
> -information about e.g. the mux function.
> -
> -
> -The following generic properties as defined in pinctrl-bindings.txt are valid
> -to specify in a pin configuration subnode:
> -
> -- pins:
> -	Usage: required
> -	Value type: <string-array>
> -	Definition: List of gpio pins affected by the properties specified in
> -		    this subnode.  Valid pins are:
> -		    gpio0-gpio69
> -
> -- function:
> -	Usage: required
> -	Value type: <string>
> -	Definition: Specify the alternative function to be configured for the
> -		    specified pins. Functions are only valid for gpio pins.
> -		    Valid values are:
> -		    atest_char, atest_char0, atest_char1, atest_char2,
> -		    atest_char3, audio_rxbclk, audio_rxd, audio_rxfsync,
> -		    audio_rxmclk, audio_txbclk, audio_txd, audio_txfsync,
> -		    audio_txmclk, blsp0_i2c, blsp0_spi, blsp0_uart, blsp1_i2c,
> -		    blsp1_spi, blsp1_uart, blsp2_i2c, blsp2_spi, blsp2_uart,
> -		    blsp3_i2c, blsp3_spi, blsp3_spi0, blsp3_spi1, blsp3_spi2,
> -		    blsp3_spi3, blsp3_uart, blsp4_i2c0, blsp4_i2c1, blsp4_spi0,
> -		    blsp4_spi1, blsp4_uart0, blsp4_uart1, blsp5_i2c, blsp5_spi,
> -		    blsp5_uart, burn0, burn1, cri_trng, cri_trng0, cri_trng1,
> -		    cxc0, cxc1, dbg_out, gcc_plltest, gcc_tlmm, gpio, ldo_en,
> -		    ldo_update, led0, led1, led2, mac0_sa0, mac0_sa1, mac1_sa0,
> -		    mac1_sa1, mac1_sa2, mac1_sa3, mac2_sa0, mac2_sa1, mdc,
> -		    mdio, pcie0_clk, pcie0_rst, pcie0_wake, pcie1_clk,
> -		    pcie1_rst, pcie1_wake, pcm_drx, pcm_dtx, pcm_fsync,
> -		    pcm_pclk, pcm_zsi0, pcm_zsi1, prng_rosc, pta1_0, pta1_1,
> -		    pta1_2, pta2_0, pta2_1, pta2_2, pwm0, pwm1, pwm2, pwm3,
> -		    qdss_cti_trig_in_a0, qdss_cti_trig_in_a1,
> -		    qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
> -		    qdss_cti_trig_out_a0, qdss_cti_trig_out_a1,
> -		    qdss_cti_trig_out_b0, qdss_cti_trig_out_b1,
> -		    qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a,
> -		    qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b,
> -		    qpic, rx0, rx1, rx2, sd_card, sd_write, tsens_max, wci2a,
> -		    wci2b, wci2c, wci2d
> -
> -- bias-disable:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as no pull.
> -
> -- bias-pull-down:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as pull down.
> -
> -- bias-pull-up:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins should be configured as pull up.
> -
> -- output-high:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins are configured in output mode, driven
> -		    high.
> -
> -- output-low:
> -	Usage: optional
> -	Value type: <none>
> -	Definition: The specified pins are configured in output mode, driven
> -		    low.
> -
> -- drive-strength:
> -	Usage: optional
> -	Value type: <u32>
> -	Definition: Selects the drive strength for the specified pins, in mA.
> -		    Valid values are: 2, 4, 6, 8, 10, 12, 14 and 16
> -
> -Example:
> -
> -	tlmm: pinctrl@1000000 {
> -		compatible = "qcom,ipq8074-pinctrl";
> -		reg = <0x1000000 0x300000>;
> -		interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> -		gpio-controller;
> -		#gpio-cells = <2>;
> -		gpio-ranges = <&tlmm 0 0 70>;
> -		interrupt-controller;
> -		#interrupt-cells = <2>;
> -
> -		uart2: uart2-default {
> -			mux {
> -				pins = "gpio23", "gpio24";
> -				function = "blsp4_uart1";
> -			};
> -
> -			rx {
> -				pins = "gpio23";
> -				drive-strength = <4>;
> -				bias-disable;
> -			};
> -
> -			tx {
> -				pins = "gpio24";
> -				drive-strength = <2>;
> -				bias-pull-up;
> -			};
> -		};
> -	};
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml
> new file mode 100644
> index 000000000000..c02dd2ad9b31
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8074-pinctrl.yaml
> @@ -0,0 +1,135 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,ipq8074-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm IPQ8074 TLMM pin controller
> +
> +maintainers:
> +  - Bjorn Andersson <andersson@kernel.org>
> +  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> +
> +description:
> +  Top Level Mode Multiplexer pin controller in Qualcomm IPQ8074 SoC.
> +
> +properties:
> +  compatible:
> +    const: qcom,ipq8074-pinctrl
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts: true
> +  interrupt-controller: true
> +  "#interrupt-cells": true
> +  gpio-controller: true
> +  "#gpio-cells": true
> +  gpio-ranges: true
> +  wakeup-parent: true
> +
> +  gpio-reserved-ranges:
> +    minItems: 1
> +    maxItems: 35
> +
> +  gpio-line-names:
> +    maxItems: 70
> +
> +patternProperties:
> +  "-state$":
> +    oneOf:
> +      - $ref: "#/$defs/qcom-ipq8074-tlmm-state"
> +      - patternProperties:
> +          "-pins$":
> +            $ref: "#/$defs/qcom-ipq8074-tlmm-state"
> +        additionalProperties: false
> +
> +$defs:
> +  qcom-ipq8074-tlmm-state:
> +    type: object
> +    description:
> +      Pinctrl node's client devices use subnodes for desired pin configuration.
> +      Client device subnodes use below standard properties.
> +    $ref: qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state
> +
> +    properties:
> +      pins:
> +        description:
> +          List of gpio pins affected by the properties specified in this
> +          subnode.
> +        items:
> +          pattern: "^gpio([0-9]|[1-6][0-9]|70)$"
> +        minItems: 1
> +        maxItems: 36
> +
> +      function:
> +        description:
> +          Specify the alternative function to be configured for the specified
> +          pins.
> +
> +        enum: [ gpio, atest_char, atest_char0, atest_char1, atest_char2,
> +                atest_char3, audio_rxbclk, audio_rxd, audio_rxfsync,
> +                audio_rxmclk, audio_txbclk, audio_txd, audio_txfsync,
> +                audio_txmclk, blsp0_i2c, blsp0_spi, blsp0_uart, blsp1_i2c,
> +                blsp1_spi, blsp1_uart, blsp2_i2c, blsp2_spi, blsp2_uart,
> +                blsp3_i2c, blsp3_spi, blsp3_spi0, blsp3_spi1, blsp3_spi2,
> +                blsp3_spi3, blsp3_uart, blsp4_i2c0, blsp4_i2c1, blsp4_spi0,
> +                blsp4_spi1, blsp4_uart0, blsp4_uart1, blsp5_i2c, blsp5_spi,
> +                blsp5_uart, burn0, burn1, cri_trng, cri_trng0, cri_trng1, cxc0,
> +                cxc1, dbg_out, gcc_plltest, gcc_tlmm, ldo_en, ldo_update, led0,
> +                led1, led2, mac0_sa0, mac0_sa1, mac1_sa0, mac1_sa1, mac1_sa2,
> +                mac1_sa3, mac2_sa0, mac2_sa1, mdc, mdio, pcie0_clk, pcie0_rst,
> +                pcie0_wake, pcie1_clk, pcie1_rst, pcie1_wake, pcm_drx, pcm_dtx,
> +                pcm_fsync, pcm_pclk, pcm_zsi0, pcm_zsi1, prng_rosc, pta1_0,
> +                pta1_1, pta1_2, pta2_0, pta2_1, pta2_2, pwm0, pwm1, pwm2, pwm3,
> +                qdss_cti_trig_in_a0, qdss_cti_trig_in_a1, qdss_cti_trig_in_b0,
> +                qdss_cti_trig_in_b1, qdss_cti_trig_out_a0,
> +                qdss_cti_trig_out_a1, qdss_cti_trig_out_b0,
> +                qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_traceclk_b,
> +                qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a,
> +                qdss_tracedata_b, qpic, rx0, rx1, rx2, sd_card, sd_write,
> +                tsens_max, wci2a, wci2b, wci2c, wci2d ]
> +
> +      bias-pull-down: true
> +      bias-pull-up: true
> +      bias-disable: true
> +      drive-strength: true
> +      input-enable: true
> +      output-high: true
> +      output-low: true
> +
> +    required:
> +      - pins
> +
> +    additionalProperties: false
> +
> +allOf:
> +  - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml#
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    tlmm: pinctrl@1000000 {
> +        compatible = "qcom,ipq8074-pinctrl";
> +        reg = <0x01000000 0x300000>;
> +        interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +        gpio-controller;
> +        gpio-ranges = <&tlmm 0 0 70>;
> +        #gpio-cells = <0x2>;
> +        interrupt-controller;
> +        #interrupt-cells = <0x2>;
> +
> +        serial4-state {
> +            pins = "gpio23", "gpio24";
> +            function = "blsp4_uart1";
> +            drive-strength = <8>;
> +            bias-disable;
> +        };
> +    };
> -- 
> 2.34.1
>
  

On Tue, 8 Nov 2022 15:23:56 +0100, Krzysztof Kozlowski wrote:
> Convert Qualcomm IPQ8074 pin controller bindings to DT schema.  Keep the
> parsing of pin configuration subnodes consistent with other Qualcomm
> schemas (children named with '-state' suffix, their children with
> '-pins').
> 
> 

Applied, thanks!

[2/2] arm64: dts: qcom: ipq8074: align TLMM pin configuration with DT schema
      commit: 1c3c31a6e7f6b467c160a4c58e385b2991e49139

Best regards,
  

On Tue, 8 Nov 2022 15:23:56 +0100, Krzysztof Kozlowski wrote:
> Convert Qualcomm IPQ8074 pin controller bindings to DT schema.  Keep the
> parsing of pin configuration subnodes consistent with other Qualcomm
> schemas (children named with '-state' suffix, their children with
> '-pins').
> 
> 

Applied, thanks!

[1/2] dt-bindings: pinctrl: qcom,ipq8074: convert to dtschema

Best regards,