diff mbox series

[v2,26/45] dt-bindings: pinctrl: at91: add bindings for SAM9X7

Message ID 20230623203056.689705-27-varshini.rajendran@microchip.com
State New
Headers
Series Add support for sam9x7 SoC family |

Commit Message

Varshini Rajendran June 23, 2023, 8:30 p.m. UTC 
  Add device tree binding for SAM9X7 pin controller.

Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
---
 .../devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt         | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

Comments

Krzysztof Kozlowski June 24, 2023, 8:24 a.m. UTC | #1 
On 23/06/2023 22:30, Varshini Rajendran wrote:
> Add device tree binding for SAM9X7 pin controller.
> 
> Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
> ---
>  .../devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt         | 3 ++-
>  1 file changed, 2 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> index e8abbdad7b5d..5a3be10dcbfb 100644
> --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
> @@ -20,6 +20,7 @@ such as pull-up, multi drive, etc.
>  Required properties for iomux controller:
>  - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl"
>  		or "atmel,sama5d3-pinctrl" or "microchip,sam9x60-pinctrl"
> +		or "microchip,sam9x7-pinctrl"

That's not what your DTS is saying. NAK.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
index e8abbdad7b5d..5a3be10dcbfb 100644
--- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt
@@ -20,6 +20,7 @@  such as pull-up, multi drive, etc.
 Required properties for iomux controller:
 - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl"
 		or "atmel,sama5d3-pinctrl" or "microchip,sam9x60-pinctrl"
+		or "microchip,sam9x7-pinctrl"
 - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be
   configured in this periph mode. All the periph and bank need to be describe.
 
@@ -119,7 +120,7 @@  Some requirements for using atmel,at91rm9200-pinctrl binding:
 
 For each bank the required properties are:
 - compatible: "atmel,at91sam9x5-gpio" or "atmel,at91rm9200-gpio" or
-  "microchip,sam9x60-gpio"
+  "microchip,sam9x60-gpio" or "microchip,sam9x7-gpio"
 - reg: physical base address and length of the controller's registers
 - interrupts: interrupt outputs from the controller
 - interrupt-controller: marks the device node as an interrupt controller