[V7,20/23] mmc: sdhci-uhs2: add add_host() and others to set up the driver
Commit Message
This is a UHS-II version of sdhci's add_host/remove_host operation.
Any sdhci drivers which are capable of handling UHS-II cards must
call those functions instead of the corresponding sdhci's.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
---
drivers/mmc/host/sdhci-uhs2.c | 119 ++++++++++++++++++++++++++++++++++
drivers/mmc/host/sdhci-uhs2.h | 2 +
drivers/mmc/host/sdhci.c | 7 +-
drivers/mmc/host/sdhci.h | 3 +
4 files changed, 129 insertions(+), 2 deletions(-)
Comments
On 31/03/23 13:55, Victor Shih wrote:
> This is a UHS-II version of sdhci's add_host/remove_host operation.
> Any sdhci drivers which are capable of handling UHS-II cards must
> call those functions instead of the corresponding sdhci's.
>
> Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
> Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
> Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> ---
> drivers/mmc/host/sdhci-uhs2.c | 119 ++++++++++++++++++++++++++++++++++
> drivers/mmc/host/sdhci-uhs2.h | 2 +
> drivers/mmc/host/sdhci.c | 7 +-
> drivers/mmc/host/sdhci.h | 3 +
> 4 files changed, 129 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-uhs2.c b/drivers/mmc/host/sdhci-uhs2.c
> index 63f4bfce70b8..610780d425bc 100644
> --- a/drivers/mmc/host/sdhci-uhs2.c
> +++ b/drivers/mmc/host/sdhci-uhs2.c
> @@ -17,6 +17,7 @@
> #include <linux/ktime.h>
> #include <linux/mmc/mmc.h>
> #include <linux/mmc/host.h>
> +#include <linux/regulator/consumer.h>
>
> #include "sdhci.h"
> #include "sdhci-uhs2.h"
> @@ -1004,6 +1005,124 @@ static irqreturn_t sdhci_uhs2_thread_irq(int irq, void *dev_id)
> return IRQ_HANDLED;
> }
>
> +/*****************************************************************************\
> + *
> + * Device allocation/registration *
> + * *
> +\*****************************************************************************/
> +
> +static int __sdhci_uhs2_add_host_v4(struct sdhci_host *host, u32 caps1)
Always returns 0, so change return type to 'void'
> +{
> + struct mmc_host *mmc;
> + u32 max_current_caps2;
> +
> + if (host->version < SDHCI_SPEC_400)
> + return 0;
> +
> + mmc = host->mmc;
> +
> + /* Support UHS2 */
> + if (caps1 & SDHCI_SUPPORT_UHS2)
> + mmc->caps2 |= MMC_CAP2_SD_UHS2;
> +
> + max_current_caps2 = sdhci_readl(host, SDHCI_MAX_CURRENT_1);
> +
> + if ((caps1 & SDHCI_CAN_VDD2_180) &&
> + !max_current_caps2 &&
> + !IS_ERR(mmc->supply.vmmc2)) {
> + /* UHS2 - VDD2 */
> + int curr = regulator_get_current_limit(mmc->supply.vmmc2);
> +
> + if (curr > 0) {
> + /* convert to SDHCI_MAX_CURRENT format */
> + curr = curr / 1000; /* convert to mA */
> + curr = curr / SDHCI_MAX_CURRENT_MULTIPLIER;
> + curr = min_t(u32, curr, SDHCI_MAX_CURRENT_LIMIT);
> + max_current_caps2 = curr;
> + }
> + }
> +
> + if (caps1 & SDHCI_CAN_VDD2_180) {
> + mmc->ocr_avail_uhs2 |= MMC_VDD_165_195;
> + /*
> + * UHS2 doesn't require this. Only UHS-I bus needs to set
> + * max current.
> + */
> + mmc->max_current_180_vdd2 = (max_current_caps2 &
> + SDHCI_MAX_CURRENT_VDD2_180_MASK) *
> + SDHCI_MAX_CURRENT_MULTIPLIER;
max_current_180_vdd2 is not used. Does it have a purpose?
> + } else {
> + mmc->caps2 &= ~MMC_CAP2_SD_UHS2;
> + }
> +
> + return 0;
> +}
> +
> +static int sdhci_uhs2_host_ops_init(struct sdhci_host *host);
> +
> +static void __sdhci_uhs2_remove_host(struct sdhci_host *host, int dead)
> +{
> + if (!sdhci_uhs2_mode(host))
> + return;
> +
> + if (!dead)
> + sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_FULL);
> +}
> +
> +int sdhci_uhs2_add_host(struct sdhci_host *host)
> +{
> + struct mmc_host *mmc = host->mmc;
> + int ret;
> +
> + ret = sdhci_setup_host(host);
> + if (ret)
> + return ret;
> +
> + if (host->version >= SDHCI_SPEC_400) {
> + ret = __sdhci_uhs2_add_host_v4(host, host->caps1);
> + if (ret)
> + goto cleanup;
> + }
> +
> + if ((mmc->caps2 & MMC_CAP2_SD_UHS2) && !host->v4_mode)
> + /* host doesn't want to enable UHS2 support */
> + /* FIXME: Do we have to do some cleanup here? */
Please do not leave FIXMEs
> + mmc->caps2 &= ~MMC_CAP2_SD_UHS2;
> +
> + /* overwrite ops */
> + if (mmc->caps2 & MMC_CAP2_SD_UHS2)
> + sdhci_uhs2_host_ops_init(host);
> +
> + host->complete_work_fn = sdhci_uhs2_complete_work;
> + host->thread_irq_fn = sdhci_uhs2_thread_irq;
> +
> + /* LED support not implemented for UHS2 */
> + host->quirks |= SDHCI_QUIRK_NO_LED;
> +
> + ret = __sdhci_add_host(host);
> + if (ret)
> + goto cleanup2;
> +
> + return 0;
> +
> +cleanup2:
> + if (host->version >= SDHCI_SPEC_400)
> + __sdhci_uhs2_remove_host(host, 0);
> +cleanup:
> + sdhci_cleanup_host(host);
> +
> + return ret;
> +}
> +EXPORT_SYMBOL_GPL(sdhci_uhs2_add_host);
> +
> +void sdhci_uhs2_remove_host(struct sdhci_host *host, int dead)
> +{
> + __sdhci_uhs2_remove_host(host, dead);
> +
> + sdhci_remove_host(host, dead);
> +}
> +EXPORT_SYMBOL_GPL(sdhci_uhs2_remove_host);
> +
> void sdhci_uhs2_request(struct mmc_host *mmc, struct mmc_request *mrq)
> {
> struct sdhci_host *host = mmc_priv(mmc);
> diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
> index f733c733c692..5b5b4a8d4f27 100644
> --- a/drivers/mmc/host/sdhci-uhs2.h
> +++ b/drivers/mmc/host/sdhci-uhs2.h
> @@ -185,5 +185,7 @@ void sdhci_uhs2_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set);
> void sdhci_uhs2_request(struct mmc_host *mmc, struct mmc_request *mrq);
> int sdhci_uhs2_request_atomic(struct mmc_host *mmc, struct mmc_request *mrq);
> u32 sdhci_uhs2_irq(struct sdhci_host *host, u32 intmask);
> +int sdhci_uhs2_add_host(struct sdhci_host *host);
> +void sdhci_uhs2_remove_host(struct sdhci_host *host, int dead);
>
> #endif /* __SDHCI_UHS2_H */
> diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> index b3cf4a26eed5..d976d3a6ff8d 100644
> --- a/drivers/mmc/host/sdhci.c
> +++ b/drivers/mmc/host/sdhci.c
> @@ -4105,6 +4105,9 @@ struct sdhci_host *sdhci_alloc_host(struct device *dev,
>
> host->max_timeout_count = 0xE;
>
> + host->complete_work_fn = sdhci_complete_work;
> + host->thread_irq_fn = sdhci_thread_irq;
> +
> return host;
> }
>
> @@ -4854,7 +4857,7 @@ int __sdhci_add_host(struct sdhci_host *host)
> if (!host->complete_wq)
> return -ENOMEM;
>
> - INIT_WORK(&host->complete_work, sdhci_complete_work);
> + INIT_WORK(&host->complete_work, host->complete_work_fn);
>
> timer_setup(&host->timer, sdhci_timeout_timer, 0);
> timer_setup(&host->data_timer, sdhci_timeout_data_timer, 0);
> @@ -4863,7 +4866,7 @@ int __sdhci_add_host(struct sdhci_host *host)
>
> sdhci_init(host, 0);
>
> - ret = request_threaded_irq(host->irq, sdhci_irq, sdhci_thread_irq,
> + ret = request_threaded_irq(host->irq, sdhci_irq, host->thread_irq_fn,
> IRQF_SHARED, mmc_hostname(mmc), host);
> if (ret) {
> pr_err("%s: Failed to request IRQ %d: %d\n",
> diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> index 9e9158f811b1..e16267f5a3c0 100644
> --- a/drivers/mmc/host/sdhci.h
> +++ b/drivers/mmc/host/sdhci.h
> @@ -627,6 +627,9 @@ struct sdhci_host {
> struct timer_list timer; /* Timer for timeouts */
> struct timer_list data_timer; /* Timer for data timeouts */
>
> + void (*complete_work_fn)(struct work_struct *work);
> + irqreturn_t (*thread_irq_fn)(int irq, void *dev_id);
> +
> #if IS_ENABLED(CONFIG_MMC_SDHCI_EXTERNAL_DMA)
> struct dma_chan *rx_chan;
> struct dma_chan *tx_chan;
Hi, Adrian
On Wed, Apr 12, 2023 at 9:12 PM Adrian Hunter <adrian.hunter@intel.com> wrote:
>
> On 31/03/23 13:55, Victor Shih wrote:
> > This is a UHS-II version of sdhci's add_host/remove_host operation.
> > Any sdhci drivers which are capable of handling UHS-II cards must
> > call those functions instead of the corresponding sdhci's.
> >
> > Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
> > Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
> > Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
> > ---
> > drivers/mmc/host/sdhci-uhs2.c | 119 ++++++++++++++++++++++++++++++++++
> > drivers/mmc/host/sdhci-uhs2.h | 2 +
> > drivers/mmc/host/sdhci.c | 7 +-
> > drivers/mmc/host/sdhci.h | 3 +
> > 4 files changed, 129 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/mmc/host/sdhci-uhs2.c b/drivers/mmc/host/sdhci-uhs2.c
> > index 63f4bfce70b8..610780d425bc 100644
> > --- a/drivers/mmc/host/sdhci-uhs2.c
> > +++ b/drivers/mmc/host/sdhci-uhs2.c
> > @@ -17,6 +17,7 @@
> > #include <linux/ktime.h>
> > #include <linux/mmc/mmc.h>
> > #include <linux/mmc/host.h>
> > +#include <linux/regulator/consumer.h>
> >
> > #include "sdhci.h"
> > #include "sdhci-uhs2.h"
> > @@ -1004,6 +1005,124 @@ static irqreturn_t sdhci_uhs2_thread_irq(int irq, void *dev_id)
> > return IRQ_HANDLED;
> > }
> >
> > +/*****************************************************************************\
> > + *
> > + * Device allocation/registration *
> > + * *
> > +\*****************************************************************************/
> > +
> > +static int __sdhci_uhs2_add_host_v4(struct sdhci_host *host, u32 caps1)
>
> Always returns 0, so change return type to 'void'
>
I will update it to the V8 version.
> > +{
> > + struct mmc_host *mmc;
> > + u32 max_current_caps2;
> > +
> > + if (host->version < SDHCI_SPEC_400)
> > + return 0;
> > +
> > + mmc = host->mmc;
> > +
> > + /* Support UHS2 */
> > + if (caps1 & SDHCI_SUPPORT_UHS2)
> > + mmc->caps2 |= MMC_CAP2_SD_UHS2;
> > +
> > + max_current_caps2 = sdhci_readl(host, SDHCI_MAX_CURRENT_1);
> > +
> > + if ((caps1 & SDHCI_CAN_VDD2_180) &&
> > + !max_current_caps2 &&
> > + !IS_ERR(mmc->supply.vmmc2)) {
> > + /* UHS2 - VDD2 */
> > + int curr = regulator_get_current_limit(mmc->supply.vmmc2);
> > +
> > + if (curr > 0) {
> > + /* convert to SDHCI_MAX_CURRENT format */
> > + curr = curr / 1000; /* convert to mA */
> > + curr = curr / SDHCI_MAX_CURRENT_MULTIPLIER;
> > + curr = min_t(u32, curr, SDHCI_MAX_CURRENT_LIMIT);
> > + max_current_caps2 = curr;
> > + }
> > + }
> > +
> > + if (caps1 & SDHCI_CAN_VDD2_180) {
> > + mmc->ocr_avail_uhs2 |= MMC_VDD_165_195;
> > + /*
> > + * UHS2 doesn't require this. Only UHS-I bus needs to set
> > + * max current.
> > + */
> > + mmc->max_current_180_vdd2 = (max_current_caps2 &
> > + SDHCI_MAX_CURRENT_VDD2_180_MASK) *
> > + SDHCI_MAX_CURRENT_MULTIPLIER;
>
> max_current_180_vdd2 is not used. Does it have a purpose?
>
I will update it to the V8 version.
> > + } else {
> > + mmc->caps2 &= ~MMC_CAP2_SD_UHS2;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int sdhci_uhs2_host_ops_init(struct sdhci_host *host);
> > +
> > +static void __sdhci_uhs2_remove_host(struct sdhci_host *host, int dead)
> > +{
> > + if (!sdhci_uhs2_mode(host))
> > + return;
> > +
> > + if (!dead)
> > + sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_FULL);
> > +}
> > +
> > +int sdhci_uhs2_add_host(struct sdhci_host *host)
> > +{
> > + struct mmc_host *mmc = host->mmc;
> > + int ret;
> > +
> > + ret = sdhci_setup_host(host);
> > + if (ret)
> > + return ret;
> > +
> > + if (host->version >= SDHCI_SPEC_400) {
> > + ret = __sdhci_uhs2_add_host_v4(host, host->caps1);
> > + if (ret)
> > + goto cleanup;
> > + }
> > +
> > + if ((mmc->caps2 & MMC_CAP2_SD_UHS2) && !host->v4_mode)
> > + /* host doesn't want to enable UHS2 support */
> > + /* FIXME: Do we have to do some cleanup here? */
>
> Please do not leave FIXMEs
>
I will update it to the V8 version.
> > + mmc->caps2 &= ~MMC_CAP2_SD_UHS2;
> > +
> > + /* overwrite ops */
> > + if (mmc->caps2 & MMC_CAP2_SD_UHS2)
> > + sdhci_uhs2_host_ops_init(host);
> > +
> > + host->complete_work_fn = sdhci_uhs2_complete_work;
> > + host->thread_irq_fn = sdhci_uhs2_thread_irq;
> > +
> > + /* LED support not implemented for UHS2 */
> > + host->quirks |= SDHCI_QUIRK_NO_LED;
> > +
> > + ret = __sdhci_add_host(host);
> > + if (ret)
> > + goto cleanup2;
> > +
> > + return 0;
> > +
> > +cleanup2:
> > + if (host->version >= SDHCI_SPEC_400)
> > + __sdhci_uhs2_remove_host(host, 0);
> > +cleanup:
> > + sdhci_cleanup_host(host);
> > +
> > + return ret;
> > +}
> > +EXPORT_SYMBOL_GPL(sdhci_uhs2_add_host);
> > +
> > +void sdhci_uhs2_remove_host(struct sdhci_host *host, int dead)
> > +{
> > + __sdhci_uhs2_remove_host(host, dead);
> > +
> > + sdhci_remove_host(host, dead);
> > +}
> > +EXPORT_SYMBOL_GPL(sdhci_uhs2_remove_host);
> > +
> > void sdhci_uhs2_request(struct mmc_host *mmc, struct mmc_request *mrq)
> > {
> > struct sdhci_host *host = mmc_priv(mmc);
> > diff --git a/drivers/mmc/host/sdhci-uhs2.h b/drivers/mmc/host/sdhci-uhs2.h
> > index f733c733c692..5b5b4a8d4f27 100644
> > --- a/drivers/mmc/host/sdhci-uhs2.h
> > +++ b/drivers/mmc/host/sdhci-uhs2.h
> > @@ -185,5 +185,7 @@ void sdhci_uhs2_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set);
> > void sdhci_uhs2_request(struct mmc_host *mmc, struct mmc_request *mrq);
> > int sdhci_uhs2_request_atomic(struct mmc_host *mmc, struct mmc_request *mrq);
> > u32 sdhci_uhs2_irq(struct sdhci_host *host, u32 intmask);
> > +int sdhci_uhs2_add_host(struct sdhci_host *host);
> > +void sdhci_uhs2_remove_host(struct sdhci_host *host, int dead);
> >
> > #endif /* __SDHCI_UHS2_H */
> > diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
> > index b3cf4a26eed5..d976d3a6ff8d 100644
> > --- a/drivers/mmc/host/sdhci.c
> > +++ b/drivers/mmc/host/sdhci.c
> > @@ -4105,6 +4105,9 @@ struct sdhci_host *sdhci_alloc_host(struct device *dev,
> >
> > host->max_timeout_count = 0xE;
> >
> > + host->complete_work_fn = sdhci_complete_work;
> > + host->thread_irq_fn = sdhci_thread_irq;
> > +
> > return host;
> > }
> >
> > @@ -4854,7 +4857,7 @@ int __sdhci_add_host(struct sdhci_host *host)
> > if (!host->complete_wq)
> > return -ENOMEM;
> >
> > - INIT_WORK(&host->complete_work, sdhci_complete_work);
> > + INIT_WORK(&host->complete_work, host->complete_work_fn);
> >
> > timer_setup(&host->timer, sdhci_timeout_timer, 0);
> > timer_setup(&host->data_timer, sdhci_timeout_data_timer, 0);
> > @@ -4863,7 +4866,7 @@ int __sdhci_add_host(struct sdhci_host *host)
> >
> > sdhci_init(host, 0);
> >
> > - ret = request_threaded_irq(host->irq, sdhci_irq, sdhci_thread_irq,
> > + ret = request_threaded_irq(host->irq, sdhci_irq, host->thread_irq_fn,
> > IRQF_SHARED, mmc_hostname(mmc), host);
> > if (ret) {
> > pr_err("%s: Failed to request IRQ %d: %d\n",
> > diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
> > index 9e9158f811b1..e16267f5a3c0 100644
> > --- a/drivers/mmc/host/sdhci.h
> > +++ b/drivers/mmc/host/sdhci.h
> > @@ -627,6 +627,9 @@ struct sdhci_host {
> > struct timer_list timer; /* Timer for timeouts */
> > struct timer_list data_timer; /* Timer for data timeouts */
> >
> > + void (*complete_work_fn)(struct work_struct *work);
> > + irqreturn_t (*thread_irq_fn)(int irq, void *dev_id);
> > +
> > #if IS_ENABLED(CONFIG_MMC_SDHCI_EXTERNAL_DMA)
> > struct dma_chan *rx_chan;
> > struct dma_chan *tx_chan;
>
Thanks, Victor Shih
@@ -17,6 +17,7 @@
#include <linux/ktime.h>
#include <linux/mmc/mmc.h>
#include <linux/mmc/host.h>
+#include <linux/regulator/consumer.h>
#include "sdhci.h"
#include "sdhci-uhs2.h"
@@ -1004,6 +1005,124 @@ static irqreturn_t sdhci_uhs2_thread_irq(int irq, void *dev_id)
return IRQ_HANDLED;
}
+/*****************************************************************************\
+ *
+ * Device allocation/registration *
+ * *
+\*****************************************************************************/
+
+static int __sdhci_uhs2_add_host_v4(struct sdhci_host *host, u32 caps1)
+{
+ struct mmc_host *mmc;
+ u32 max_current_caps2;
+
+ if (host->version < SDHCI_SPEC_400)
+ return 0;
+
+ mmc = host->mmc;
+
+ /* Support UHS2 */
+ if (caps1 & SDHCI_SUPPORT_UHS2)
+ mmc->caps2 |= MMC_CAP2_SD_UHS2;
+
+ max_current_caps2 = sdhci_readl(host, SDHCI_MAX_CURRENT_1);
+
+ if ((caps1 & SDHCI_CAN_VDD2_180) &&
+ !max_current_caps2 &&
+ !IS_ERR(mmc->supply.vmmc2)) {
+ /* UHS2 - VDD2 */
+ int curr = regulator_get_current_limit(mmc->supply.vmmc2);
+
+ if (curr > 0) {
+ /* convert to SDHCI_MAX_CURRENT format */
+ curr = curr / 1000; /* convert to mA */
+ curr = curr / SDHCI_MAX_CURRENT_MULTIPLIER;
+ curr = min_t(u32, curr, SDHCI_MAX_CURRENT_LIMIT);
+ max_current_caps2 = curr;
+ }
+ }
+
+ if (caps1 & SDHCI_CAN_VDD2_180) {
+ mmc->ocr_avail_uhs2 |= MMC_VDD_165_195;
+ /*
+ * UHS2 doesn't require this. Only UHS-I bus needs to set
+ * max current.
+ */
+ mmc->max_current_180_vdd2 = (max_current_caps2 &
+ SDHCI_MAX_CURRENT_VDD2_180_MASK) *
+ SDHCI_MAX_CURRENT_MULTIPLIER;
+ } else {
+ mmc->caps2 &= ~MMC_CAP2_SD_UHS2;
+ }
+
+ return 0;
+}
+
+static int sdhci_uhs2_host_ops_init(struct sdhci_host *host);
+
+static void __sdhci_uhs2_remove_host(struct sdhci_host *host, int dead)
+{
+ if (!sdhci_uhs2_mode(host))
+ return;
+
+ if (!dead)
+ sdhci_uhs2_reset(host, SDHCI_UHS2_SW_RESET_FULL);
+}
+
+int sdhci_uhs2_add_host(struct sdhci_host *host)
+{
+ struct mmc_host *mmc = host->mmc;
+ int ret;
+
+ ret = sdhci_setup_host(host);
+ if (ret)
+ return ret;
+
+ if (host->version >= SDHCI_SPEC_400) {
+ ret = __sdhci_uhs2_add_host_v4(host, host->caps1);
+ if (ret)
+ goto cleanup;
+ }
+
+ if ((mmc->caps2 & MMC_CAP2_SD_UHS2) && !host->v4_mode)
+ /* host doesn't want to enable UHS2 support */
+ /* FIXME: Do we have to do some cleanup here? */
+ mmc->caps2 &= ~MMC_CAP2_SD_UHS2;
+
+ /* overwrite ops */
+ if (mmc->caps2 & MMC_CAP2_SD_UHS2)
+ sdhci_uhs2_host_ops_init(host);
+
+ host->complete_work_fn = sdhci_uhs2_complete_work;
+ host->thread_irq_fn = sdhci_uhs2_thread_irq;
+
+ /* LED support not implemented for UHS2 */
+ host->quirks |= SDHCI_QUIRK_NO_LED;
+
+ ret = __sdhci_add_host(host);
+ if (ret)
+ goto cleanup2;
+
+ return 0;
+
+cleanup2:
+ if (host->version >= SDHCI_SPEC_400)
+ __sdhci_uhs2_remove_host(host, 0);
+cleanup:
+ sdhci_cleanup_host(host);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(sdhci_uhs2_add_host);
+
+void sdhci_uhs2_remove_host(struct sdhci_host *host, int dead)
+{
+ __sdhci_uhs2_remove_host(host, dead);
+
+ sdhci_remove_host(host, dead);
+}
+EXPORT_SYMBOL_GPL(sdhci_uhs2_remove_host);
+
void sdhci_uhs2_request(struct mmc_host *mmc, struct mmc_request *mrq)
{
struct sdhci_host *host = mmc_priv(mmc);
@@ -185,5 +185,7 @@ void sdhci_uhs2_clear_set_irqs(struct sdhci_host *host, u32 clear, u32 set);
void sdhci_uhs2_request(struct mmc_host *mmc, struct mmc_request *mrq);
int sdhci_uhs2_request_atomic(struct mmc_host *mmc, struct mmc_request *mrq);
u32 sdhci_uhs2_irq(struct sdhci_host *host, u32 intmask);
+int sdhci_uhs2_add_host(struct sdhci_host *host);
+void sdhci_uhs2_remove_host(struct sdhci_host *host, int dead);
#endif /* __SDHCI_UHS2_H */
@@ -4105,6 +4105,9 @@ struct sdhci_host *sdhci_alloc_host(struct device *dev,
host->max_timeout_count = 0xE;
+ host->complete_work_fn = sdhci_complete_work;
+ host->thread_irq_fn = sdhci_thread_irq;
+
return host;
}
@@ -4854,7 +4857,7 @@ int __sdhci_add_host(struct sdhci_host *host)
if (!host->complete_wq)
return -ENOMEM;
- INIT_WORK(&host->complete_work, sdhci_complete_work);
+ INIT_WORK(&host->complete_work, host->complete_work_fn);
timer_setup(&host->timer, sdhci_timeout_timer, 0);
timer_setup(&host->data_timer, sdhci_timeout_data_timer, 0);
@@ -4863,7 +4866,7 @@ int __sdhci_add_host(struct sdhci_host *host)
sdhci_init(host, 0);
- ret = request_threaded_irq(host->irq, sdhci_irq, sdhci_thread_irq,
+ ret = request_threaded_irq(host->irq, sdhci_irq, host->thread_irq_fn,
IRQF_SHARED, mmc_hostname(mmc), host);
if (ret) {
pr_err("%s: Failed to request IRQ %d: %d\n",
@@ -627,6 +627,9 @@ struct sdhci_host {
struct timer_list timer; /* Timer for timeouts */
struct timer_list data_timer; /* Timer for data timeouts */
+ void (*complete_work_fn)(struct work_struct *work);
+ irqreturn_t (*thread_irq_fn)(int irq, void *dev_id);
+
#if IS_ENABLED(CONFIG_MMC_SDHCI_EXTERNAL_DMA)
struct dma_chan *rx_chan;
struct dma_chan *tx_chan;