dt-bindings: arm: drop unneeded quotes and use absolute /schemas path
Commit Message
Cleanup bindings dropping unneeded quotes. Once all these are fixed,
checking for this can be enabled in yamllint. Also absolute path
starting with /schemas is preferred.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
---
.../bindings/arm/arm,vexpress-juno.yaml | 10 +++++-----
.../devicetree/bindings/arm/cpus.yaml | 18 +++++++++---------
.../devicetree/bindings/arm/psci.yaml | 2 +-
3 files changed, 15 insertions(+), 15 deletions(-)
Comments
On Fri, Jun 9, 2023 at 4:07 PM Krzysztof Kozlowski
<krzysztof.kozlowski@linaro.org> wrote:
> Cleanup bindings dropping unneeded quotes. Once all these are fixed,
> checking for this can be enabled in yamllint. Also absolute path
> starting with /schemas is preferred.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Yours,
Linus Walleij
On Fri, 09 Jun 2023 16:07:54 +0200, Krzysztof Kozlowski wrote:
> Cleanup bindings dropping unneeded quotes. Once all these are fixed,
> checking for this can be enabled in yamllint. Also absolute path
> starting with /schemas is preferred.
>
> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> ---
> .../bindings/arm/arm,vexpress-juno.yaml | 10 +++++-----
> .../devicetree/bindings/arm/cpus.yaml | 18 +++++++++---------
> .../devicetree/bindings/arm/psci.yaml | 2 +-
> 3 files changed, 15 insertions(+), 15 deletions(-)
>
Applied, thanks!
@@ -122,14 +122,14 @@ properties:
arm,vexpress,position:
description: When daughterboards are stacked on one site, their position
in the stack be be described this attribute.
- $ref: '/schemas/types.yaml#/definitions/uint32'
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
arm,vexpress,dcc:
description: When describing tiles consisting of more than one DCC, its
number can be specified with this attribute.
- $ref: '/schemas/types.yaml#/definitions/uint32'
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
@@ -180,13 +180,13 @@ patternProperties:
- const: simple-bus
arm,v2m-memory-map:
description: This describes the memory map type.
- $ref: '/schemas/types.yaml#/definitions/string'
+ $ref: /schemas/types.yaml#/definitions/string
enum:
- rs1
- rs2
arm,hbi:
- $ref: '/schemas/types.yaml#/definitions/uint32'
+ $ref: /schemas/types.yaml#/definitions/uint32
description: This indicates the ARM HBI (Hardware Board ID), this is
ARM's unique board model ID, visible on the PCB's silkscreen.
@@ -197,7 +197,7 @@ patternProperties:
property, describing the physical location of the children nodes.
0 means motherboard site, while 1 and 2 are daughterboard sites, and
0xf means "sisterboard" which is the site containing the main CPU tile.
- $ref: '/schemas/types.yaml#/definitions/uint32'
+ $ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 15
@@ -197,7 +197,7 @@ properties:
- qcom,scorpion
enable-method:
- $ref: '/schemas/types.yaml#/definitions/string'
+ $ref: /schemas/types.yaml#/definitions/string
oneOf:
# On ARM v8 64-bit this property is required
- enum:
@@ -246,8 +246,8 @@ properties:
cpu-release-addr:
oneOf:
- - $ref: '/schemas/types.yaml#/definitions/uint32'
- - $ref: '/schemas/types.yaml#/definitions/uint64'
+ - $ref: /schemas/types.yaml#/definitions/uint32
+ - $ref: /schemas/types.yaml#/definitions/uint64
description:
The DT specification defines this as 64-bit always, but some 32-bit Arm
systems have used a 32-bit value which must be supported.
@@ -255,7 +255,7 @@ properties:
property value of "spin-table".
cpu-idle-states:
- $ref: '/schemas/types.yaml#/definitions/phandle-array'
+ $ref: /schemas/types.yaml#/definitions/phandle-array
items:
maxItems: 1
description: |
@@ -271,7 +271,7 @@ properties:
cci-control-port: true
dynamic-power-coefficient:
- $ref: '/schemas/types.yaml#/definitions/uint32'
+ $ref: /schemas/types.yaml#/definitions/uint32
description:
A u32 value that represents the running time dynamic
power coefficient in units of uW/MHz/V^2. The
@@ -308,7 +308,7 @@ properties:
PM domain provider, must be "psci".
qcom,saw:
- $ref: '/schemas/types.yaml#/definitions/phandle'
+ $ref: /schemas/types.yaml#/definitions/phandle
description: |
Specifies the SAW* node associated with this CPU.
@@ -318,7 +318,7 @@ properties:
* arm/msm/qcom,saw2.txt
qcom,acc:
- $ref: '/schemas/types.yaml#/definitions/phandle'
+ $ref: /schemas/types.yaml#/definitions/phandle
description: |
Specifies the ACC* node associated with this CPU.
@@ -329,7 +329,7 @@ properties:
* arm/msm/qcom,kpss-acc.txt
rockchip,pmu:
- $ref: '/schemas/types.yaml#/definitions/phandle'
+ $ref: /schemas/types.yaml#/definitions/phandle
description: |
Specifies the syscon node controlling the cpu core power domains.
@@ -339,7 +339,7 @@ properties:
the cpu-core power-domains.
secondary-boot-reg:
- $ref: '/schemas/types.yaml#/definitions/uint32'
+ $ref: /schemas/types.yaml#/definitions/uint32
description: |
Required for systems that have an "enable-method" property value of
"brcm,bcm11351-cpu-method", "brcm,bcm23550" or "brcm,bcm-nsp-smp".
@@ -100,7 +100,7 @@ properties:
patternProperties:
"^power-domain-":
- $ref: "../power/power-domain.yaml#"
+ $ref: /schemas/power/power-domain.yaml#
type: object
description: |