[v10,2/2] spi: loongson: add bus driver for the loongson spi controller
Commit Message
This bus driver supports the Loongson SPI hardware controller in the
Loongson platforms and supports to use DTS and PCI framework to
register SPI device resources.
Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
---
MAINTAINERS | 4 +
drivers/spi/Kconfig | 26 +++
drivers/spi/Makefile | 3 +
drivers/spi/spi-loongson-core.c | 279 ++++++++++++++++++++++++++++++++
drivers/spi/spi-loongson-pci.c | 61 +++++++
drivers/spi/spi-loongson-plat.c | 46 ++++++
drivers/spi/spi-loongson.h | 47 ++++++
7 files changed, 466 insertions(+)
create mode 100644 drivers/spi/spi-loongson-core.c
create mode 100644 drivers/spi/spi-loongson-pci.c
create mode 100644 drivers/spi/spi-loongson-plat.c
create mode 100644 drivers/spi/spi-loongson.h
Comments
Hello,
> -----Original Message-----
> From: Yinbo Zhu <zhuyinbo@loongson.cn>
> Sent: Tuesday, May 16, 2023 6:42 PM
> To: Mark Brown <broonie@kernel.org>; Rob Herring <robh+dt@kernel.org>;
> Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>; linux-
> spi@vger.kernel.org; devicetree@vger.kernel.org; linux-
> kernel@vger.kernel.org
> Cc: Jianmin Lv <lvjianmin@loongson.cn>; wanghongliang@loongson.cn; Liu
> Peibao <liupeibao@loongson.cn>; loongson-kernel@lists.loongnix.cn; Yinbo
> Zhu <zhuyinbo@loongson.cn>
> Subject: [PATCH v10 2/2] spi: loongson: add bus driver for the loongson spi
> controller
>
> CAUTION: This message has originated from an External Source. Please use
> proper judgment and caution when opening attachments, clicking links, or
> responding to this email.
>
>
> This bus driver supports the Loongson SPI hardware controller in the Loongson
> platforms and supports to use DTS and PCI framework to register SPI device
> resources.
>
> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
> ---
> MAINTAINERS | 4 +
> drivers/spi/Kconfig | 26 +++
> drivers/spi/Makefile | 3 +
> drivers/spi/spi-loongson-core.c | 279 ++++++++++++++++++++++++++++++++
> drivers/spi/spi-loongson-pci.c | 61 +++++++ drivers/spi/spi-loongson-plat.c |
> 46 ++++++
> drivers/spi/spi-loongson.h | 47 ++++++
> 7 files changed, 466 insertions(+)
> create mode 100644 drivers/spi/spi-loongson-core.c create mode 100644
> drivers/spi/spi-loongson-pci.c create mode 100644 drivers/spi/spi-loongson-
> plat.c create mode 100644 drivers/spi/spi-loongson.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index dfcc5db4bbc0..ab08aba965f3 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -12218,6 +12218,10 @@ M: Yinbo Zhu <zhuyinbo@loongson.cn>
> L: linux-spi@vger.kernel.org
> S: Maintained
> F: Documentation/devicetree/bindings/spi/loongson,ls2k-spi.yaml
> +F: drivers/spi/spi-loongson-core.c
> +F: drivers/spi/spi-loongson-pci.c
> +F: drivers/spi/spi-loongson-plat.c
> +F: drivers/spi/spi-loongson.h
>
> LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
> M: Sathya Prakash <sathya.prakash@broadcom.com>
> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index
> 3de2ebe8294a..6b953904792e 100644
> --- a/drivers/spi/Kconfig
> +++ b/drivers/spi/Kconfig
> @@ -516,6 +516,32 @@ config SPI_LM70_LLP
> which interfaces to an LM70 temperature sensor using
> a parallel port.
>
> +config SPI_LOONGSON_CORE
> + tristate
> + depends on LOONGARCH || COMPILE_TEST
> +
> +config SPI_LOONGSON_PCI
> + tristate "Loongson SPI Controller PCI Driver Support"
> + select SPI_LOONGSON_CORE
> + depends on PCI && (LOONGARCH || COMPILE_TEST)
> + help
> + This bus driver supports the Loongson SPI hardware controller in
> + the Loongson platforms and supports to use PCI framework to
> + register SPI device resources.
> + Say Y or M here if you want to use the SPI controller on
> + Loongson platform.
> +
> +config SPI_LOONGSON_PLATFORM
> + tristate "Loongson SPI Controller Platform Driver Support"
> + select SPI_LOONGSON_CORE
> + depends on OF && (LOONGARCH || COMPILE_TEST)
> + help
> + This bus driver supports the Loongson SPI hardware controller in
> + the Loongson platforms and supports to use DTS framework to
> + register SPI device resources.
> + Say Y or M here if you want to use the SPI controller on
> + Loongson platform.
> +
> config SPI_LP8841_RTC
> tristate "ICP DAS LP-8841 SPI Controller for RTC"
> depends on MACH_PXA27X_DT || COMPILE_TEST diff --git
> a/drivers/spi/Makefile b/drivers/spi/Makefile index
> 28c4817a8a74..3e933064d237 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -71,6 +71,9 @@ obj-$(CONFIG_SPI_INTEL_PLATFORM) += spi-intel-
> platform.o
> obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o
> obj-$(CONFIG_SPI_JCORE) += spi-jcore.o
> obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
> +obj-$(CONFIG_SPI_LOONGSON_CORE) += spi-loongson-core.o
> +obj-$(CONFIG_SPI_LOONGSON_PCI) += spi-loongson-pci.o
> +obj-$(CONFIG_SPI_LOONGSON_PLATFORM) += spi-loongson-plat.o
> obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o
> obj-$(CONFIG_SPI_MESON_SPICC) += spi-meson-spicc.o
> obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
> diff --git a/drivers/spi/spi-loongson-core.c b/drivers/spi/spi-loongson-core.c
> new file mode 100644 index 000000000000..435a58b0d9da
> --- /dev/null
> +++ b/drivers/spi/spi-loongson-core.c
> @@ -0,0 +1,279 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// Loongson SPI Support
> +// Copyright (C) 2023 Loongson Technology Corporation Limited
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +
> +#include "spi-loongson.h"
> +
> +static inline void loongson_spi_write_reg(struct loongson_spi *spi, unsigned
> char reg,
> + unsigned char data) {
> + writeb(data, spi->base + reg);
> +}
> +
> +static inline char loongson_spi_read_reg(struct loongson_spi *spi,
> +unsigned char reg) {
> + return readb(spi->base + reg);
> +}
> +
> +static void loongson_spi_set_cs(struct spi_device *spi, bool val) {
> + int cs;
> + struct loongson_spi *loongson_spi =
> +spi_master_get_devdata(spi->master);
> +
> + cs = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SFCS_REG)
> + & ~(0x11 << spi->chip_select);
New set/get APIs for accessing spi->chip_select were introduced by
https://github.com/torvalds/linux/commit/303feb3cc06ac0665d0ee9c1414941200e60e8a3
please use these APIs instead of accessing spi->chip_select directly.
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG,
> + (val ? (0x11 << spi->chip_select) :
Same here
> + (0x1 << spi->chip_select)) | cs);
Same here
> +}
> +
> +static void loongson_spi_set_clk(struct loongson_spi *loongson_spi,
> +unsigned int hz) {
> + unsigned char val;
> + unsigned int div, div_tmp;
> + const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
> +
> + div = clamp_val(DIV_ROUND_UP_ULL(loongson_spi->clk_rate, hz), 2,
> 4096);
> + div_tmp = rdiv[fls(div - 1)];
> + loongson_spi->spcr = (div_tmp & GENMASK(1, 0)) >> 0;
> + loongson_spi->sper = (div_tmp & GENMASK(3, 2)) >> 2;
> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, (val &
> ~3) |
> + loongson_spi->spcr);
> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPER_REG);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG, (val &
> ~3) |
> + loongson_spi->sper);
> + loongson_spi->hz = hz;
> +}
> +
> +static void loongson_spi_set_mode(struct loongson_spi *loongson_spi,
> + struct spi_device *spi) {
> + unsigned char val;
> +
> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
> + val &= ~(LOONGSON_SPI_SPCR_CPOL | LOONGSON_SPI_SPCR_CPHA);
> + if (spi->mode & SPI_CPOL)
> + val |= LOONGSON_SPI_SPCR_CPOL;
> + if (spi->mode & SPI_CPHA)
> + val |= LOONGSON_SPI_SPCR_CPHA;
> +
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, val);
> + loongson_spi->mode |= spi->mode; }
> +
> +static int loongson_spi_update_state(struct loongson_spi *loongson_spi,
> + struct spi_device *spi, struct
> +spi_transfer *t) {
> + unsigned int hz;
> +
> + if (t)
> + hz = t->speed_hz;
> +
> + if (hz && loongson_spi->hz != hz)
> + loongson_spi_set_clk(loongson_spi, hz);
> +
> + if ((spi->mode ^ loongson_spi->mode) & SPI_MODE_X_MASK)
> + loongson_spi_set_mode(loongson_spi, spi);
> +
> + return 0;
> +}
> +
> +static int loongson_spi_setup(struct spi_device *spi) {
> + struct loongson_spi *loongson_spi;
> +
> + loongson_spi = spi_master_get_devdata(spi->master);
> + if (spi->bits_per_word % 8)
> + return -EINVAL;
> +
> + if (spi->chip_select >= spi->master->num_chipselect)
Same here
Regards,
Amit
> + return -EINVAL;
> +
> + loongson_spi->hz = 0;
> + loongson_spi_set_cs(spi, 1);
> +
> + return 0;
> +}
> +
> +static int loongson_spi_write_read_8bit(struct spi_device *spi, const u8
> **tx_buf,
> + u8 **rx_buf, unsigned int num) {
> + struct loongson_spi *loongson_spi =
> +spi_master_get_devdata(spi->master);
> +
> + if (tx_buf && *tx_buf)
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG,
> *((*tx_buf)++));
> + else
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG,
> 0);
> + readb_poll_timeout(loongson_spi->base + LOONGSON_SPI_SPSR_REG,
> loongson_spi->spsr,
> + (loongson_spi->spsr & 0x1) != 1, 1,
> + MSEC_PER_SEC);
> +
> + if (rx_buf && *rx_buf)
> + *(*rx_buf)++ = loongson_spi_read_reg(loongson_spi,
> LOONGSON_SPI_FIFO_REG);
> + else
> + loongson_spi_read_reg(loongson_spi,
> + LOONGSON_SPI_FIFO_REG);
> +
> + return 0;
> +}
> +
> +static unsigned int loongson_spi_write_read(struct spi_device *spi,
> +struct spi_transfer *xfer) {
> + unsigned int count;
> + const u8 *tx = xfer->tx_buf;
> + u8 *rx = xfer->rx_buf;
> +
> + count = xfer->len;
> +
> + do {
> + if (loongson_spi_write_read_8bit(spi, &tx, &rx, count) < 0)
> + goto out;
> + count--;
> + } while (count);
> +
> +out:
> + return xfer->len - count;
> +}
> +
> +static int loongson_spi_prepare_message(struct spi_controller *ctlr,
> +struct spi_message *m) {
> + struct loongson_spi *loongson_spi =
> +spi_controller_get_devdata(ctlr);
> +
> + loongson_spi->para = loongson_spi_read_reg(loongson_spi,
> LOONGSON_SPI_PARA_REG);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG,
> + loongson_spi->para & ~1);
> +
> + return 0;
> +}
> +
> +static int loongson_spi_transfer_one(struct spi_controller *ctrl, struct
> spi_device *spi,
> + struct spi_transfer *xfer) {
> + struct loongson_spi *loongson_spi =
> +spi_master_get_devdata(spi->master);
> +
> + loongson_spi_update_state(loongson_spi, spi, xfer);
> + if (xfer->len)
> + xfer->len = loongson_spi_write_read(spi, xfer);
> +
> + return 0;
> +}
> +
> +static int loongson_spi_unprepare_message(struct spi_controller *ctrl,
> +struct spi_message *m) {
> + struct loongson_spi *loongson_spi =
> +spi_controller_get_devdata(ctrl);
> +
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG,
> + loongson_spi->para);
> +
> + return 0;
> +}
> +
> +static void loongson_spi_reginit(struct loongson_spi *loongson_spi_dev)
> +{
> + unsigned char val;
> +
> + val = loongson_spi_read_reg(loongson_spi_dev,
> LOONGSON_SPI_SPCR_REG);
> + val &= ~LOONGSON_SPI_SPCR_SPE;
> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG,
> + val);
> +
> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPSR_REG,
> + (LOONGSON_SPI_SPSR_SPIF |
> + LOONGSON_SPI_SPSR_WCOL));
> +
> + val = loongson_spi_read_reg(loongson_spi_dev,
> LOONGSON_SPI_SPCR_REG);
> + val |= LOONGSON_SPI_SPCR_SPE;
> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG,
> +val); }
> +
> +int loongson_spi_init_master(struct device *dev, void __iomem *regs) {
> + struct spi_master *master;
> + struct loongson_spi *spi;
> + struct clk *clk;
> +
> + master = devm_spi_alloc_master(dev, sizeof(struct loongson_spi));
> + if (master == NULL)
> + return -ENOMEM;
> +
> + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
> + master->setup = loongson_spi_setup;
> + master->prepare_message = loongson_spi_prepare_message;
> + master->transfer_one = loongson_spi_transfer_one;
> + master->unprepare_message = loongson_spi_unprepare_message;
> + master->set_cs = loongson_spi_set_cs;
> + master->num_chipselect = 4;
> + device_set_node(&master->dev, dev_fwnode(dev));
> + dev_set_drvdata(dev, master);
> +
> + spi = spi_master_get_devdata(master);
> + spi->base = regs;
> + spi->master = master;
> +
> + clk = devm_clk_get_optional(dev, NULL);
> + if (!IS_ERR(clk))
> + spi->clk_rate = clk_get_rate(clk);
> + else
> + return dev_err_probe(dev, PTR_ERR(clk), "unable to get
> + clock\n");
> +
> + loongson_spi_reginit(spi);
> +
> + spi->mode = 0;
> +
> + return devm_spi_register_master(dev, master); }
> +EXPORT_SYMBOL_NS_GPL(loongson_spi_init_master,
> SPI_LOONGSON_CORE);
> +
> +static int __maybe_unused loongson_spi_suspend(struct device *dev) {
> + struct loongson_spi *loongson_spi;
> + struct spi_master *master;
> +
> + master = dev_get_drvdata(dev);
> + spi_master_suspend(master);
> +
> + loongson_spi = spi_master_get_devdata(master);
> +
> + loongson_spi->spcr = loongson_spi_read_reg(loongson_spi,
> LOONGSON_SPI_SPCR_REG);
> + loongson_spi->sper = loongson_spi_read_reg(loongson_spi,
> LOONGSON_SPI_SPER_REG);
> + loongson_spi->spsr = loongson_spi_read_reg(loongson_spi,
> LOONGSON_SPI_SPSR_REG);
> + loongson_spi->para = loongson_spi_read_reg(loongson_spi,
> LOONGSON_SPI_PARA_REG);
> + loongson_spi->sfcs = loongson_spi_read_reg(loongson_spi,
> LOONGSON_SPI_SFCS_REG);
> + loongson_spi->timi = loongson_spi_read_reg(loongson_spi,
> + LOONGSON_SPI_TIMI_REG);
> +
> + return 0;
> +}
> +
> +static int __maybe_unused loongson_spi_resume(struct device *dev) {
> + struct loongson_spi *loongson_spi;
> + struct spi_master *master;
> +
> + master = dev_get_drvdata(dev);
> + loongson_spi = spi_master_get_devdata(master);
> +
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG,
> loongson_spi->spcr);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG,
> loongson_spi->sper);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPSR_REG,
> loongson_spi->spsr);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG,
> loongson_spi->para);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG,
> loongson_spi->sfcs);
> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_TIMI_REG,
> + loongson_spi->timi);
> +
> + spi_master_resume(master);
> +
> + return 0;
> +}
> +
> +const struct dev_pm_ops loongson_spi_dev_pm_ops = {
> + .suspend = loongson_spi_suspend,
> + .resume = loongson_spi_resume,
> +};
> +EXPORT_SYMBOL_NS_GPL(loongson_spi_dev_pm_ops,
> SPI_LOONGSON_CORE);
> +
> +MODULE_DESCRIPTION("Loongson SPI core driver");
> MODULE_LICENSE("GPL");
> diff --git a/drivers/spi/spi-loongson-pci.c b/drivers/spi/spi-loongson-pci.c new
> file mode 100644 index 000000000000..c351a689150a
> --- /dev/null
> +++ b/drivers/spi/spi-loongson-pci.c
> @@ -0,0 +1,61 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// PCI interface driver for Loongson SPI Support // Copyright (C) 2023
> +Loongson Technology Corporation Limited
> +
> +#include <linux/pci.h>
> +
> +#include "spi-loongson.h"
> +
> +static int loongson_spi_pci_register(struct pci_dev *pdev,
> + const struct pci_device_id *ent) {
> + int ret;
> + void __iomem *reg_base;
> + struct device *dev = &pdev->dev;
> + int pci_bar = 0;
> +
> + ret = pcim_enable_device(pdev);
> + if (ret < 0)
> + return dev_err_probe(dev, ret, "cannot enable pci
> + device\n");
> +
> + ret = pcim_iomap_regions(pdev, BIT(pci_bar), pci_name(pdev));
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to request and
> + remap memory\n");
> +
> + reg_base = pcim_iomap_table(pdev)[pci_bar];
> +
> + ret = loongson_spi_init_master(dev, reg_base);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to initialize
> + master\n");
> +
> + return 0;
> +}
> +
> +static void loongson_spi_pci_unregister(struct pci_dev *pdev) {
> + pcim_iounmap_regions(pdev, BIT(0));
> + pci_disable_device(pdev);
> +}
> +
> +static struct pci_device_id loongson_spi_devices[] = {
> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a1b) },
> + { },
> +};
> +MODULE_DEVICE_TABLE(pci, loongson_spi_devices);
> +
> +static struct pci_driver loongson_spi_pci_driver = {
> + .name = "loongson-spi-pci",
> + .id_table = loongson_spi_devices,
> + .probe = loongson_spi_pci_register,
> + .remove = loongson_spi_pci_unregister,
> + .driver = {
> + .bus = &pci_bus_type,
> + .pm = &loongson_spi_dev_pm_ops,
> + },
> +};
> +module_pci_driver(loongson_spi_pci_driver);
> +
> +MODULE_DESCRIPTION("Loongson spi pci driver"); MODULE_LICENSE("GPL");
> +MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
> diff --git a/drivers/spi/spi-loongson-plat.c b/drivers/spi/spi-loongson-plat.c
> new file mode 100644 index 000000000000..2e0388d84044
> --- /dev/null
> +++ b/drivers/spi/spi-loongson-plat.c
> @@ -0,0 +1,46 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// Platform driver for Loongson SPI Support // Copyright (C) 2023
> +Loongson Technology Corporation Limited
> +
> +#include <linux/of.h>
> +#include <linux/platform_device.h>
> +
> +#include "spi-loongson.h"
> +
> +static int loongson_spi_platform_probe(struct platform_device *pdev) {
> + int ret;
> + void __iomem *reg_base;
> + struct device *dev = &pdev->dev;
> +
> + reg_base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(reg_base))
> + return PTR_ERR(reg_base);
> +
> + ret = loongson_spi_init_master(dev, reg_base);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to initialize
> + master\n");
> +
> + return ret;
> +}
> +
> +static const struct of_device_id loongson_spi_id_table[] = {
> + { .compatible = "loongson,ls2k-spi" },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, loongson_spi_id_table);
> +
> +static struct platform_driver loongson_spi_plat_driver = {
> + .probe = loongson_spi_platform_probe,
> + .driver = {
> + .name = "loongson-spi",
> + .bus = &platform_bus_type,
> + .pm = &loongson_spi_dev_pm_ops,
> + .of_match_table = loongson_spi_id_table,
> + },
> +};
> +module_platform_driver(loongson_spi_plat_driver);
> +
> +MODULE_DESCRIPTION("Loongson spi platform driver");
> +MODULE_LICENSE("GPL"); MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
> diff --git a/drivers/spi/spi-loongson.h b/drivers/spi/spi-loongson.h new file
> mode 100644 index 000000000000..5dca9750efa3
> --- /dev/null
> +++ b/drivers/spi/spi-loongson.h
> @@ -0,0 +1,47 @@
> +/* SPDX-License-Identifier: GPL-2.0+ */
> +/* Header File for Loongson SPI Driver. */
> +/* Copyright (C) 2023 Loongson Technology Corporation Limited */
> +
> +#ifndef __LINUX_SPI_LOONGSON_H
> +#define __LINUX_SPI_LOONGSON_H
> +
> +#include <linux/bits.h>
> +#include <linux/device.h>
> +#include <linux/pm.h>
> +#include <linux/spi/spi.h>
> +#include <linux/types.h>
> +
> +#define LOONGSON_SPI_SPCR_REG 0x00
> +#define LOONGSON_SPI_SPSR_REG 0x01
> +#define LOONGSON_SPI_FIFO_REG 0x02
> +#define LOONGSON_SPI_SPER_REG 0x03
> +#define LOONGSON_SPI_PARA_REG 0x04
> +#define LOONGSON_SPI_SFCS_REG 0x05
> +#define LOONGSON_SPI_TIMI_REG 0x06
> +
> +/* Bits definition for Loongson SPI register */
> +#define LOONGSON_SPI_PARA_MEM_EN BIT(0)
> +#define LOONGSON_SPI_SPCR_CPHA BIT(2)
> +#define LOONGSON_SPI_SPCR_CPOL BIT(3)
> +#define LOONGSON_SPI_SPCR_SPE BIT(6)
> +#define LOONGSON_SPI_SPSR_WCOL BIT(6)
> +#define LOONGSON_SPI_SPSR_SPIF BIT(7)
> +
> +struct loongson_spi {
> + struct spi_master *master;
> + void __iomem *base;
> + int cs_active;
> + unsigned int hz;
> + unsigned char spcr;
> + unsigned char sper;
> + unsigned char spsr;
> + unsigned char para;
> + unsigned char sfcs;
> + unsigned char timi;
> + unsigned int mode;
> + u64 clk_rate;
> +};
> +
> +int loongson_spi_init_master(struct device *dev, void __iomem *reg);
> +extern const struct dev_pm_ops loongson_spi_dev_pm_ops; #endif /*
> +__LINUX_SPI_LOONGSON_H */
> --
> 2.20.1
在 2023/5/17 下午12:55, Mahapatra, Amit Kumar 写道:
> Hello,
>
>> -----Original Message-----
>> From: Yinbo Zhu <zhuyinbo@loongson.cn>
>> Sent: Tuesday, May 16, 2023 6:42 PM
>> To: Mark Brown <broonie@kernel.org>; Rob Herring <robh+dt@kernel.org>;
>> Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>; linux-
>> spi@vger.kernel.org; devicetree@vger.kernel.org; linux-
>> kernel@vger.kernel.org
>> Cc: Jianmin Lv <lvjianmin@loongson.cn>; wanghongliang@loongson.cn; Liu
>> Peibao <liupeibao@loongson.cn>; loongson-kernel@lists.loongnix.cn; Yinbo
>> Zhu <zhuyinbo@loongson.cn>
>> Subject: [PATCH v10 2/2] spi: loongson: add bus driver for the loongson spi
>> controller
>>
>> CAUTION: This message has originated from an External Source. Please use
>> proper judgment and caution when opening attachments, clicking links, or
>> responding to this email.
>>
>>
>> This bus driver supports the Loongson SPI hardware controller in the Loongson
>> platforms and supports to use DTS and PCI framework to register SPI device
>> resources.
>>
>> Signed-off-by: Yinbo Zhu <zhuyinbo@loongson.cn>
>> ---
>> MAINTAINERS | 4 +
>> drivers/spi/Kconfig | 26 +++
>> drivers/spi/Makefile | 3 +
>> drivers/spi/spi-loongson-core.c | 279 ++++++++++++++++++++++++++++++++
>> drivers/spi/spi-loongson-pci.c | 61 +++++++ drivers/spi/spi-loongson-plat.c |
>> 46 ++++++
>> drivers/spi/spi-loongson.h | 47 ++++++
>> 7 files changed, 466 insertions(+)
>> create mode 100644 drivers/spi/spi-loongson-core.c create mode 100644
>> drivers/spi/spi-loongson-pci.c create mode 100644 drivers/spi/spi-loongson-
>> plat.c create mode 100644 drivers/spi/spi-loongson.h
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index dfcc5db4bbc0..ab08aba965f3 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -12218,6 +12218,10 @@ M: Yinbo Zhu <zhuyinbo@loongson.cn>
>> L: linux-spi@vger.kernel.org
>> S: Maintained
>> F: Documentation/devicetree/bindings/spi/loongson,ls2k-spi.yaml
>> +F: drivers/spi/spi-loongson-core.c
>> +F: drivers/spi/spi-loongson-pci.c
>> +F: drivers/spi/spi-loongson-plat.c
>> +F: drivers/spi/spi-loongson.h
>>
>> LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
>> M: Sathya Prakash <sathya.prakash@broadcom.com>
>> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index
>> 3de2ebe8294a..6b953904792e 100644
>> --- a/drivers/spi/Kconfig
>> +++ b/drivers/spi/Kconfig
>> @@ -516,6 +516,32 @@ config SPI_LM70_LLP
>> which interfaces to an LM70 temperature sensor using
>> a parallel port.
>>
>> +config SPI_LOONGSON_CORE
>> + tristate
>> + depends on LOONGARCH || COMPILE_TEST
>> +
>> +config SPI_LOONGSON_PCI
>> + tristate "Loongson SPI Controller PCI Driver Support"
>> + select SPI_LOONGSON_CORE
>> + depends on PCI && (LOONGARCH || COMPILE_TEST)
>> + help
>> + This bus driver supports the Loongson SPI hardware controller in
>> + the Loongson platforms and supports to use PCI framework to
>> + register SPI device resources.
>> + Say Y or M here if you want to use the SPI controller on
>> + Loongson platform.
>> +
>> +config SPI_LOONGSON_PLATFORM
>> + tristate "Loongson SPI Controller Platform Driver Support"
>> + select SPI_LOONGSON_CORE
>> + depends on OF && (LOONGARCH || COMPILE_TEST)
>> + help
>> + This bus driver supports the Loongson SPI hardware controller in
>> + the Loongson platforms and supports to use DTS framework to
>> + register SPI device resources.
>> + Say Y or M here if you want to use the SPI controller on
>> + Loongson platform.
>> +
>> config SPI_LP8841_RTC
>> tristate "ICP DAS LP-8841 SPI Controller for RTC"
>> depends on MACH_PXA27X_DT || COMPILE_TEST diff --git
>> a/drivers/spi/Makefile b/drivers/spi/Makefile index
>> 28c4817a8a74..3e933064d237 100644
>> --- a/drivers/spi/Makefile
>> +++ b/drivers/spi/Makefile
>> @@ -71,6 +71,9 @@ obj-$(CONFIG_SPI_INTEL_PLATFORM) += spi-intel-
>> platform.o
>> obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o
>> obj-$(CONFIG_SPI_JCORE) += spi-jcore.o
>> obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
>> +obj-$(CONFIG_SPI_LOONGSON_CORE) += spi-loongson-core.o
>> +obj-$(CONFIG_SPI_LOONGSON_PCI) += spi-loongson-pci.o
>> +obj-$(CONFIG_SPI_LOONGSON_PLATFORM) += spi-loongson-plat.o
>> obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o
>> obj-$(CONFIG_SPI_MESON_SPICC) += spi-meson-spicc.o
>> obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
>> diff --git a/drivers/spi/spi-loongson-core.c b/drivers/spi/spi-loongson-core.c
>> new file mode 100644 index 000000000000..435a58b0d9da
>> --- /dev/null
>> +++ b/drivers/spi/spi-loongson-core.c
>> @@ -0,0 +1,279 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +// Loongson SPI Support
>> +// Copyright (C) 2023 Loongson Technology Corporation Limited
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/err.h>
>> +#include <linux/init.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +
>> +#include "spi-loongson.h"
>> +
>> +static inline void loongson_spi_write_reg(struct loongson_spi *spi, unsigned
>> char reg,
>> + unsigned char data) {
>> + writeb(data, spi->base + reg);
>> +}
>> +
>> +static inline char loongson_spi_read_reg(struct loongson_spi *spi,
>> +unsigned char reg) {
>> + return readb(spi->base + reg);
>> +}
>> +
>> +static void loongson_spi_set_cs(struct spi_device *spi, bool val) {
>> + int cs;
>> + struct loongson_spi *loongson_spi =
>> +spi_master_get_devdata(spi->master);
>> +
>> + cs = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SFCS_REG)
>> + & ~(0x11 << spi->chip_select);
>
> New set/get APIs for accessing spi->chip_select were introduced by
> https://github.com/torvalds/linux/commit/303feb3cc06ac0665d0ee9c1414941200e60e8a3
> please use these APIs instead of accessing spi->chip_select directly.
okay, I got it. I will use spi_get_chipselect() to replace all
spi->chip_select in spi driver.
Thanks.
>
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG,
>> + (val ? (0x11 << spi->chip_select) :
>
> Same here
>> + (0x1 << spi->chip_select)) | cs);
>
> Same here
>> +}
>> +
>> +static void loongson_spi_set_clk(struct loongson_spi *loongson_spi,
>> +unsigned int hz) {
>> + unsigned char val;
>> + unsigned int div, div_tmp;
>> + const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
>> +
>> + div = clamp_val(DIV_ROUND_UP_ULL(loongson_spi->clk_rate, hz), 2,
>> 4096);
>> + div_tmp = rdiv[fls(div - 1)];
>> + loongson_spi->spcr = (div_tmp & GENMASK(1, 0)) >> 0;
>> + loongson_spi->sper = (div_tmp & GENMASK(3, 2)) >> 2;
>> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, (val &
>> ~3) |
>> + loongson_spi->spcr);
>> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPER_REG);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG, (val &
>> ~3) |
>> + loongson_spi->sper);
>> + loongson_spi->hz = hz;
>> +}
>> +
>> +static void loongson_spi_set_mode(struct loongson_spi *loongson_spi,
>> + struct spi_device *spi) {
>> + unsigned char val;
>> +
>> + val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
>> + val &= ~(LOONGSON_SPI_SPCR_CPOL | LOONGSON_SPI_SPCR_CPHA);
>> + if (spi->mode & SPI_CPOL)
>> + val |= LOONGSON_SPI_SPCR_CPOL;
>> + if (spi->mode & SPI_CPHA)
>> + val |= LOONGSON_SPI_SPCR_CPHA;
>> +
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, val);
>> + loongson_spi->mode |= spi->mode; }
>> +
>> +static int loongson_spi_update_state(struct loongson_spi *loongson_spi,
>> + struct spi_device *spi, struct
>> +spi_transfer *t) {
>> + unsigned int hz;
>> +
>> + if (t)
>> + hz = t->speed_hz;
>> +
>> + if (hz && loongson_spi->hz != hz)
>> + loongson_spi_set_clk(loongson_spi, hz);
>> +
>> + if ((spi->mode ^ loongson_spi->mode) & SPI_MODE_X_MASK)
>> + loongson_spi_set_mode(loongson_spi, spi);
>> +
>> + return 0;
>> +}
>> +
>> +static int loongson_spi_setup(struct spi_device *spi) {
>> + struct loongson_spi *loongson_spi;
>> +
>> + loongson_spi = spi_master_get_devdata(spi->master);
>> + if (spi->bits_per_word % 8)
>> + return -EINVAL;
>> +
>> + if (spi->chip_select >= spi->master->num_chipselect)
>
> Same here
>
> Regards,
> Amit
>
>> + return -EINVAL;
>> +
>> + loongson_spi->hz = 0;
>> + loongson_spi_set_cs(spi, 1);
>> +
>> + return 0;
>> +}
>> +
>> +static int loongson_spi_write_read_8bit(struct spi_device *spi, const u8
>> **tx_buf,
>> + u8 **rx_buf, unsigned int num) {
>> + struct loongson_spi *loongson_spi =
>> +spi_master_get_devdata(spi->master);
>> +
>> + if (tx_buf && *tx_buf)
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG,
>> *((*tx_buf)++));
>> + else
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG,
>> 0);
>> + readb_poll_timeout(loongson_spi->base + LOONGSON_SPI_SPSR_REG,
>> loongson_spi->spsr,
>> + (loongson_spi->spsr & 0x1) != 1, 1,
>> + MSEC_PER_SEC);
>> +
>> + if (rx_buf && *rx_buf)
>> + *(*rx_buf)++ = loongson_spi_read_reg(loongson_spi,
>> LOONGSON_SPI_FIFO_REG);
>> + else
>> + loongson_spi_read_reg(loongson_spi,
>> + LOONGSON_SPI_FIFO_REG);
>> +
>> + return 0;
>> +}
>> +
>> +static unsigned int loongson_spi_write_read(struct spi_device *spi,
>> +struct spi_transfer *xfer) {
>> + unsigned int count;
>> + const u8 *tx = xfer->tx_buf;
>> + u8 *rx = xfer->rx_buf;
>> +
>> + count = xfer->len;
>> +
>> + do {
>> + if (loongson_spi_write_read_8bit(spi, &tx, &rx, count) < 0)
>> + goto out;
>> + count--;
>> + } while (count);
>> +
>> +out:
>> + return xfer->len - count;
>> +}
>> +
>> +static int loongson_spi_prepare_message(struct spi_controller *ctlr,
>> +struct spi_message *m) {
>> + struct loongson_spi *loongson_spi =
>> +spi_controller_get_devdata(ctlr);
>> +
>> + loongson_spi->para = loongson_spi_read_reg(loongson_spi,
>> LOONGSON_SPI_PARA_REG);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG,
>> + loongson_spi->para & ~1);
>> +
>> + return 0;
>> +}
>> +
>> +static int loongson_spi_transfer_one(struct spi_controller *ctrl, struct
>> spi_device *spi,
>> + struct spi_transfer *xfer) {
>> + struct loongson_spi *loongson_spi =
>> +spi_master_get_devdata(spi->master);
>> +
>> + loongson_spi_update_state(loongson_spi, spi, xfer);
>> + if (xfer->len)
>> + xfer->len = loongson_spi_write_read(spi, xfer);
>> +
>> + return 0;
>> +}
>> +
>> +static int loongson_spi_unprepare_message(struct spi_controller *ctrl,
>> +struct spi_message *m) {
>> + struct loongson_spi *loongson_spi =
>> +spi_controller_get_devdata(ctrl);
>> +
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG,
>> + loongson_spi->para);
>> +
>> + return 0;
>> +}
>> +
>> +static void loongson_spi_reginit(struct loongson_spi *loongson_spi_dev)
>> +{
>> + unsigned char val;
>> +
>> + val = loongson_spi_read_reg(loongson_spi_dev,
>> LOONGSON_SPI_SPCR_REG);
>> + val &= ~LOONGSON_SPI_SPCR_SPE;
>> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG,
>> + val);
>> +
>> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPSR_REG,
>> + (LOONGSON_SPI_SPSR_SPIF |
>> + LOONGSON_SPI_SPSR_WCOL));
>> +
>> + val = loongson_spi_read_reg(loongson_spi_dev,
>> LOONGSON_SPI_SPCR_REG);
>> + val |= LOONGSON_SPI_SPCR_SPE;
>> + loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG,
>> +val); }
>> +
>> +int loongson_spi_init_master(struct device *dev, void __iomem *regs) {
>> + struct spi_master *master;
>> + struct loongson_spi *spi;
>> + struct clk *clk;
>> +
>> + master = devm_spi_alloc_master(dev, sizeof(struct loongson_spi));
>> + if (master == NULL)
>> + return -ENOMEM;
>> +
>> + master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
>> + master->setup = loongson_spi_setup;
>> + master->prepare_message = loongson_spi_prepare_message;
>> + master->transfer_one = loongson_spi_transfer_one;
>> + master->unprepare_message = loongson_spi_unprepare_message;
>> + master->set_cs = loongson_spi_set_cs;
>> + master->num_chipselect = 4;
>> + device_set_node(&master->dev, dev_fwnode(dev));
>> + dev_set_drvdata(dev, master);
>> +
>> + spi = spi_master_get_devdata(master);
>> + spi->base = regs;
>> + spi->master = master;
>> +
>> + clk = devm_clk_get_optional(dev, NULL);
>> + if (!IS_ERR(clk))
>> + spi->clk_rate = clk_get_rate(clk);
>> + else
>> + return dev_err_probe(dev, PTR_ERR(clk), "unable to get
>> + clock\n");
>> +
>> + loongson_spi_reginit(spi);
>> +
>> + spi->mode = 0;
>> +
>> + return devm_spi_register_master(dev, master); }
>> +EXPORT_SYMBOL_NS_GPL(loongson_spi_init_master,
>> SPI_LOONGSON_CORE);
>> +
>> +static int __maybe_unused loongson_spi_suspend(struct device *dev) {
>> + struct loongson_spi *loongson_spi;
>> + struct spi_master *master;
>> +
>> + master = dev_get_drvdata(dev);
>> + spi_master_suspend(master);
>> +
>> + loongson_spi = spi_master_get_devdata(master);
>> +
>> + loongson_spi->spcr = loongson_spi_read_reg(loongson_spi,
>> LOONGSON_SPI_SPCR_REG);
>> + loongson_spi->sper = loongson_spi_read_reg(loongson_spi,
>> LOONGSON_SPI_SPER_REG);
>> + loongson_spi->spsr = loongson_spi_read_reg(loongson_spi,
>> LOONGSON_SPI_SPSR_REG);
>> + loongson_spi->para = loongson_spi_read_reg(loongson_spi,
>> LOONGSON_SPI_PARA_REG);
>> + loongson_spi->sfcs = loongson_spi_read_reg(loongson_spi,
>> LOONGSON_SPI_SFCS_REG);
>> + loongson_spi->timi = loongson_spi_read_reg(loongson_spi,
>> + LOONGSON_SPI_TIMI_REG);
>> +
>> + return 0;
>> +}
>> +
>> +static int __maybe_unused loongson_spi_resume(struct device *dev) {
>> + struct loongson_spi *loongson_spi;
>> + struct spi_master *master;
>> +
>> + master = dev_get_drvdata(dev);
>> + loongson_spi = spi_master_get_devdata(master);
>> +
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG,
>> loongson_spi->spcr);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG,
>> loongson_spi->sper);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPSR_REG,
>> loongson_spi->spsr);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG,
>> loongson_spi->para);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG,
>> loongson_spi->sfcs);
>> + loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_TIMI_REG,
>> + loongson_spi->timi);
>> +
>> + spi_master_resume(master);
>> +
>> + return 0;
>> +}
>> +
>> +const struct dev_pm_ops loongson_spi_dev_pm_ops = {
>> + .suspend = loongson_spi_suspend,
>> + .resume = loongson_spi_resume,
>> +};
>> +EXPORT_SYMBOL_NS_GPL(loongson_spi_dev_pm_ops,
>> SPI_LOONGSON_CORE);
>> +
>> +MODULE_DESCRIPTION("Loongson SPI core driver");
>> MODULE_LICENSE("GPL");
>> diff --git a/drivers/spi/spi-loongson-pci.c b/drivers/spi/spi-loongson-pci.c new
>> file mode 100644 index 000000000000..c351a689150a
>> --- /dev/null
>> +++ b/drivers/spi/spi-loongson-pci.c
>> @@ -0,0 +1,61 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +// PCI interface driver for Loongson SPI Support // Copyright (C) 2023
>> +Loongson Technology Corporation Limited
>> +
>> +#include <linux/pci.h>
>> +
>> +#include "spi-loongson.h"
>> +
>> +static int loongson_spi_pci_register(struct pci_dev *pdev,
>> + const struct pci_device_id *ent) {
>> + int ret;
>> + void __iomem *reg_base;
>> + struct device *dev = &pdev->dev;
>> + int pci_bar = 0;
>> +
>> + ret = pcim_enable_device(pdev);
>> + if (ret < 0)
>> + return dev_err_probe(dev, ret, "cannot enable pci
>> + device\n");
>> +
>> + ret = pcim_iomap_regions(pdev, BIT(pci_bar), pci_name(pdev));
>> + if (ret)
>> + return dev_err_probe(dev, ret, "failed to request and
>> + remap memory\n");
>> +
>> + reg_base = pcim_iomap_table(pdev)[pci_bar];
>> +
>> + ret = loongson_spi_init_master(dev, reg_base);
>> + if (ret)
>> + return dev_err_probe(dev, ret, "failed to initialize
>> + master\n");
>> +
>> + return 0;
>> +}
>> +
>> +static void loongson_spi_pci_unregister(struct pci_dev *pdev) {
>> + pcim_iounmap_regions(pdev, BIT(0));
>> + pci_disable_device(pdev);
>> +}
>> +
>> +static struct pci_device_id loongson_spi_devices[] = {
>> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
>> + { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a1b) },
>> + { },
>> +};
>> +MODULE_DEVICE_TABLE(pci, loongson_spi_devices);
>> +
>> +static struct pci_driver loongson_spi_pci_driver = {
>> + .name = "loongson-spi-pci",
>> + .id_table = loongson_spi_devices,
>> + .probe = loongson_spi_pci_register,
>> + .remove = loongson_spi_pci_unregister,
>> + .driver = {
>> + .bus = &pci_bus_type,
>> + .pm = &loongson_spi_dev_pm_ops,
>> + },
>> +};
>> +module_pci_driver(loongson_spi_pci_driver);
>> +
>> +MODULE_DESCRIPTION("Loongson spi pci driver"); MODULE_LICENSE("GPL");
>> +MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
>> diff --git a/drivers/spi/spi-loongson-plat.c b/drivers/spi/spi-loongson-plat.c
>> new file mode 100644 index 000000000000..2e0388d84044
>> --- /dev/null
>> +++ b/drivers/spi/spi-loongson-plat.c
>> @@ -0,0 +1,46 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +// Platform driver for Loongson SPI Support // Copyright (C) 2023
>> +Loongson Technology Corporation Limited
>> +
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +
>> +#include "spi-loongson.h"
>> +
>> +static int loongson_spi_platform_probe(struct platform_device *pdev) {
>> + int ret;
>> + void __iomem *reg_base;
>> + struct device *dev = &pdev->dev;
>> +
>> + reg_base = devm_platform_ioremap_resource(pdev, 0);
>> + if (IS_ERR(reg_base))
>> + return PTR_ERR(reg_base);
>> +
>> + ret = loongson_spi_init_master(dev, reg_base);
>> + if (ret)
>> + return dev_err_probe(dev, ret, "failed to initialize
>> + master\n");
>> +
>> + return ret;
>> +}
>> +
>> +static const struct of_device_id loongson_spi_id_table[] = {
>> + { .compatible = "loongson,ls2k-spi" },
>> + { }
>> +};
>> +MODULE_DEVICE_TABLE(of, loongson_spi_id_table);
>> +
>> +static struct platform_driver loongson_spi_plat_driver = {
>> + .probe = loongson_spi_platform_probe,
>> + .driver = {
>> + .name = "loongson-spi",
>> + .bus = &platform_bus_type,
>> + .pm = &loongson_spi_dev_pm_ops,
>> + .of_match_table = loongson_spi_id_table,
>> + },
>> +};
>> +module_platform_driver(loongson_spi_plat_driver);
>> +
>> +MODULE_DESCRIPTION("Loongson spi platform driver");
>> +MODULE_LICENSE("GPL"); MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
>> diff --git a/drivers/spi/spi-loongson.h b/drivers/spi/spi-loongson.h new file
>> mode 100644 index 000000000000..5dca9750efa3
>> --- /dev/null
>> +++ b/drivers/spi/spi-loongson.h
>> @@ -0,0 +1,47 @@
>> +/* SPDX-License-Identifier: GPL-2.0+ */
>> +/* Header File for Loongson SPI Driver. */
>> +/* Copyright (C) 2023 Loongson Technology Corporation Limited */
>> +
>> +#ifndef __LINUX_SPI_LOONGSON_H
>> +#define __LINUX_SPI_LOONGSON_H
>> +
>> +#include <linux/bits.h>
>> +#include <linux/device.h>
>> +#include <linux/pm.h>
>> +#include <linux/spi/spi.h>
>> +#include <linux/types.h>
>> +
>> +#define LOONGSON_SPI_SPCR_REG 0x00
>> +#define LOONGSON_SPI_SPSR_REG 0x01
>> +#define LOONGSON_SPI_FIFO_REG 0x02
>> +#define LOONGSON_SPI_SPER_REG 0x03
>> +#define LOONGSON_SPI_PARA_REG 0x04
>> +#define LOONGSON_SPI_SFCS_REG 0x05
>> +#define LOONGSON_SPI_TIMI_REG 0x06
>> +
>> +/* Bits definition for Loongson SPI register */
>> +#define LOONGSON_SPI_PARA_MEM_EN BIT(0)
>> +#define LOONGSON_SPI_SPCR_CPHA BIT(2)
>> +#define LOONGSON_SPI_SPCR_CPOL BIT(3)
>> +#define LOONGSON_SPI_SPCR_SPE BIT(6)
>> +#define LOONGSON_SPI_SPSR_WCOL BIT(6)
>> +#define LOONGSON_SPI_SPSR_SPIF BIT(7)
>> +
>> +struct loongson_spi {
>> + struct spi_master *master;
>> + void __iomem *base;
>> + int cs_active;
>> + unsigned int hz;
>> + unsigned char spcr;
>> + unsigned char sper;
>> + unsigned char spsr;
>> + unsigned char para;
>> + unsigned char sfcs;
>> + unsigned char timi;
>> + unsigned int mode;
>> + u64 clk_rate;
>> +};
>> +
>> +int loongson_spi_init_master(struct device *dev, void __iomem *reg);
>> +extern const struct dev_pm_ops loongson_spi_dev_pm_ops; #endif /*
>> +__LINUX_SPI_LOONGSON_H */
>> --
>> 2.20.1
@@ -12218,6 +12218,10 @@ M: Yinbo Zhu <zhuyinbo@loongson.cn>
L: linux-spi@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/spi/loongson,ls2k-spi.yaml
+F: drivers/spi/spi-loongson-core.c
+F: drivers/spi/spi-loongson-pci.c
+F: drivers/spi/spi-loongson-plat.c
+F: drivers/spi/spi-loongson.h
LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI)
M: Sathya Prakash <sathya.prakash@broadcom.com>
@@ -516,6 +516,32 @@ config SPI_LM70_LLP
which interfaces to an LM70 temperature sensor using
a parallel port.
+config SPI_LOONGSON_CORE
+ tristate
+ depends on LOONGARCH || COMPILE_TEST
+
+config SPI_LOONGSON_PCI
+ tristate "Loongson SPI Controller PCI Driver Support"
+ select SPI_LOONGSON_CORE
+ depends on PCI && (LOONGARCH || COMPILE_TEST)
+ help
+ This bus driver supports the Loongson SPI hardware controller in
+ the Loongson platforms and supports to use PCI framework to
+ register SPI device resources.
+ Say Y or M here if you want to use the SPI controller on
+ Loongson platform.
+
+config SPI_LOONGSON_PLATFORM
+ tristate "Loongson SPI Controller Platform Driver Support"
+ select SPI_LOONGSON_CORE
+ depends on OF && (LOONGARCH || COMPILE_TEST)
+ help
+ This bus driver supports the Loongson SPI hardware controller in
+ the Loongson platforms and supports to use DTS framework to
+ register SPI device resources.
+ Say Y or M here if you want to use the SPI controller on
+ Loongson platform.
+
config SPI_LP8841_RTC
tristate "ICP DAS LP-8841 SPI Controller for RTC"
depends on MACH_PXA27X_DT || COMPILE_TEST
@@ -71,6 +71,9 @@ obj-$(CONFIG_SPI_INTEL_PLATFORM) += spi-intel-platform.o
obj-$(CONFIG_SPI_LANTIQ_SSC) += spi-lantiq-ssc.o
obj-$(CONFIG_SPI_JCORE) += spi-jcore.o
obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o
+obj-$(CONFIG_SPI_LOONGSON_CORE) += spi-loongson-core.o
+obj-$(CONFIG_SPI_LOONGSON_PCI) += spi-loongson-pci.o
+obj-$(CONFIG_SPI_LOONGSON_PLATFORM) += spi-loongson-plat.o
obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o
obj-$(CONFIG_SPI_MESON_SPICC) += spi-meson-spicc.o
obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o
new file mode 100644
@@ -0,0 +1,279 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Loongson SPI Support
+// Copyright (C) 2023 Loongson Technology Corporation Limited
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+
+#include "spi-loongson.h"
+
+static inline void loongson_spi_write_reg(struct loongson_spi *spi, unsigned char reg,
+ unsigned char data)
+{
+ writeb(data, spi->base + reg);
+}
+
+static inline char loongson_spi_read_reg(struct loongson_spi *spi, unsigned char reg)
+{
+ return readb(spi->base + reg);
+}
+
+static void loongson_spi_set_cs(struct spi_device *spi, bool val)
+{
+ int cs;
+ struct loongson_spi *loongson_spi = spi_master_get_devdata(spi->master);
+
+ cs = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SFCS_REG)
+ & ~(0x11 << spi->chip_select);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG,
+ (val ? (0x11 << spi->chip_select) :
+ (0x1 << spi->chip_select)) | cs);
+}
+
+static void loongson_spi_set_clk(struct loongson_spi *loongson_spi, unsigned int hz)
+{
+ unsigned char val;
+ unsigned int div, div_tmp;
+ const char rdiv[12] = {0, 1, 4, 2, 3, 5, 6, 7, 8, 9, 10, 11};
+
+ div = clamp_val(DIV_ROUND_UP_ULL(loongson_spi->clk_rate, hz), 2, 4096);
+ div_tmp = rdiv[fls(div - 1)];
+ loongson_spi->spcr = (div_tmp & GENMASK(1, 0)) >> 0;
+ loongson_spi->sper = (div_tmp & GENMASK(3, 2)) >> 2;
+ val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, (val & ~3) |
+ loongson_spi->spcr);
+ val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPER_REG);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG, (val & ~3) |
+ loongson_spi->sper);
+ loongson_spi->hz = hz;
+}
+
+static void loongson_spi_set_mode(struct loongson_spi *loongson_spi,
+ struct spi_device *spi)
+{
+ unsigned char val;
+
+ val = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
+ val &= ~(LOONGSON_SPI_SPCR_CPOL | LOONGSON_SPI_SPCR_CPHA);
+ if (spi->mode & SPI_CPOL)
+ val |= LOONGSON_SPI_SPCR_CPOL;
+ if (spi->mode & SPI_CPHA)
+ val |= LOONGSON_SPI_SPCR_CPHA;
+
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, val);
+ loongson_spi->mode |= spi->mode;
+}
+
+static int loongson_spi_update_state(struct loongson_spi *loongson_spi,
+ struct spi_device *spi, struct spi_transfer *t)
+{
+ unsigned int hz;
+
+ if (t)
+ hz = t->speed_hz;
+
+ if (hz && loongson_spi->hz != hz)
+ loongson_spi_set_clk(loongson_spi, hz);
+
+ if ((spi->mode ^ loongson_spi->mode) & SPI_MODE_X_MASK)
+ loongson_spi_set_mode(loongson_spi, spi);
+
+ return 0;
+}
+
+static int loongson_spi_setup(struct spi_device *spi)
+{
+ struct loongson_spi *loongson_spi;
+
+ loongson_spi = spi_master_get_devdata(spi->master);
+ if (spi->bits_per_word % 8)
+ return -EINVAL;
+
+ if (spi->chip_select >= spi->master->num_chipselect)
+ return -EINVAL;
+
+ loongson_spi->hz = 0;
+ loongson_spi_set_cs(spi, 1);
+
+ return 0;
+}
+
+static int loongson_spi_write_read_8bit(struct spi_device *spi, const u8 **tx_buf,
+ u8 **rx_buf, unsigned int num)
+{
+ struct loongson_spi *loongson_spi = spi_master_get_devdata(spi->master);
+
+ if (tx_buf && *tx_buf)
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG, *((*tx_buf)++));
+ else
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_FIFO_REG, 0);
+ readb_poll_timeout(loongson_spi->base + LOONGSON_SPI_SPSR_REG, loongson_spi->spsr,
+ (loongson_spi->spsr & 0x1) != 1, 1, MSEC_PER_SEC);
+
+ if (rx_buf && *rx_buf)
+ *(*rx_buf)++ = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_FIFO_REG);
+ else
+ loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_FIFO_REG);
+
+ return 0;
+}
+
+static unsigned int loongson_spi_write_read(struct spi_device *spi, struct spi_transfer *xfer)
+{
+ unsigned int count;
+ const u8 *tx = xfer->tx_buf;
+ u8 *rx = xfer->rx_buf;
+
+ count = xfer->len;
+
+ do {
+ if (loongson_spi_write_read_8bit(spi, &tx, &rx, count) < 0)
+ goto out;
+ count--;
+ } while (count);
+
+out:
+ return xfer->len - count;
+}
+
+static int loongson_spi_prepare_message(struct spi_controller *ctlr, struct spi_message *m)
+{
+ struct loongson_spi *loongson_spi = spi_controller_get_devdata(ctlr);
+
+ loongson_spi->para = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_PARA_REG);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG, loongson_spi->para & ~1);
+
+ return 0;
+}
+
+static int loongson_spi_transfer_one(struct spi_controller *ctrl, struct spi_device *spi,
+ struct spi_transfer *xfer)
+{
+ struct loongson_spi *loongson_spi = spi_master_get_devdata(spi->master);
+
+ loongson_spi_update_state(loongson_spi, spi, xfer);
+ if (xfer->len)
+ xfer->len = loongson_spi_write_read(spi, xfer);
+
+ return 0;
+}
+
+static int loongson_spi_unprepare_message(struct spi_controller *ctrl, struct spi_message *m)
+{
+ struct loongson_spi *loongson_spi = spi_controller_get_devdata(ctrl);
+
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG, loongson_spi->para);
+
+ return 0;
+}
+
+static void loongson_spi_reginit(struct loongson_spi *loongson_spi_dev)
+{
+ unsigned char val;
+
+ val = loongson_spi_read_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG);
+ val &= ~LOONGSON_SPI_SPCR_SPE;
+ loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG, val);
+
+ loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPSR_REG,
+ (LOONGSON_SPI_SPSR_SPIF | LOONGSON_SPI_SPSR_WCOL));
+
+ val = loongson_spi_read_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG);
+ val |= LOONGSON_SPI_SPCR_SPE;
+ loongson_spi_write_reg(loongson_spi_dev, LOONGSON_SPI_SPCR_REG, val);
+}
+
+int loongson_spi_init_master(struct device *dev, void __iomem *regs)
+{
+ struct spi_master *master;
+ struct loongson_spi *spi;
+ struct clk *clk;
+
+ master = devm_spi_alloc_master(dev, sizeof(struct loongson_spi));
+ if (master == NULL)
+ return -ENOMEM;
+
+ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
+ master->setup = loongson_spi_setup;
+ master->prepare_message = loongson_spi_prepare_message;
+ master->transfer_one = loongson_spi_transfer_one;
+ master->unprepare_message = loongson_spi_unprepare_message;
+ master->set_cs = loongson_spi_set_cs;
+ master->num_chipselect = 4;
+ device_set_node(&master->dev, dev_fwnode(dev));
+ dev_set_drvdata(dev, master);
+
+ spi = spi_master_get_devdata(master);
+ spi->base = regs;
+ spi->master = master;
+
+ clk = devm_clk_get_optional(dev, NULL);
+ if (!IS_ERR(clk))
+ spi->clk_rate = clk_get_rate(clk);
+ else
+ return dev_err_probe(dev, PTR_ERR(clk), "unable to get clock\n");
+
+ loongson_spi_reginit(spi);
+
+ spi->mode = 0;
+
+ return devm_spi_register_master(dev, master);
+}
+EXPORT_SYMBOL_NS_GPL(loongson_spi_init_master, SPI_LOONGSON_CORE);
+
+static int __maybe_unused loongson_spi_suspend(struct device *dev)
+{
+ struct loongson_spi *loongson_spi;
+ struct spi_master *master;
+
+ master = dev_get_drvdata(dev);
+ spi_master_suspend(master);
+
+ loongson_spi = spi_master_get_devdata(master);
+
+ loongson_spi->spcr = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPCR_REG);
+ loongson_spi->sper = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPER_REG);
+ loongson_spi->spsr = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SPSR_REG);
+ loongson_spi->para = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_PARA_REG);
+ loongson_spi->sfcs = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_SFCS_REG);
+ loongson_spi->timi = loongson_spi_read_reg(loongson_spi, LOONGSON_SPI_TIMI_REG);
+
+ return 0;
+}
+
+static int __maybe_unused loongson_spi_resume(struct device *dev)
+{
+ struct loongson_spi *loongson_spi;
+ struct spi_master *master;
+
+ master = dev_get_drvdata(dev);
+ loongson_spi = spi_master_get_devdata(master);
+
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPCR_REG, loongson_spi->spcr);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPER_REG, loongson_spi->sper);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SPSR_REG, loongson_spi->spsr);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_PARA_REG, loongson_spi->para);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_SFCS_REG, loongson_spi->sfcs);
+ loongson_spi_write_reg(loongson_spi, LOONGSON_SPI_TIMI_REG, loongson_spi->timi);
+
+ spi_master_resume(master);
+
+ return 0;
+}
+
+const struct dev_pm_ops loongson_spi_dev_pm_ops = {
+ .suspend = loongson_spi_suspend,
+ .resume = loongson_spi_resume,
+};
+EXPORT_SYMBOL_NS_GPL(loongson_spi_dev_pm_ops, SPI_LOONGSON_CORE);
+
+MODULE_DESCRIPTION("Loongson SPI core driver");
+MODULE_LICENSE("GPL");
new file mode 100644
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0+
+// PCI interface driver for Loongson SPI Support
+// Copyright (C) 2023 Loongson Technology Corporation Limited
+
+#include <linux/pci.h>
+
+#include "spi-loongson.h"
+
+static int loongson_spi_pci_register(struct pci_dev *pdev,
+ const struct pci_device_id *ent)
+{
+ int ret;
+ void __iomem *reg_base;
+ struct device *dev = &pdev->dev;
+ int pci_bar = 0;
+
+ ret = pcim_enable_device(pdev);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "cannot enable pci device\n");
+
+ ret = pcim_iomap_regions(pdev, BIT(pci_bar), pci_name(pdev));
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to request and remap memory\n");
+
+ reg_base = pcim_iomap_table(pdev)[pci_bar];
+
+ ret = loongson_spi_init_master(dev, reg_base);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to initialize master\n");
+
+ return 0;
+}
+
+static void loongson_spi_pci_unregister(struct pci_dev *pdev)
+{
+ pcim_iounmap_regions(pdev, BIT(0));
+ pci_disable_device(pdev);
+}
+
+static struct pci_device_id loongson_spi_devices[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a0b) },
+ { PCI_DEVICE(PCI_VENDOR_ID_LOONGSON, 0x7a1b) },
+ { },
+};
+MODULE_DEVICE_TABLE(pci, loongson_spi_devices);
+
+static struct pci_driver loongson_spi_pci_driver = {
+ .name = "loongson-spi-pci",
+ .id_table = loongson_spi_devices,
+ .probe = loongson_spi_pci_register,
+ .remove = loongson_spi_pci_unregister,
+ .driver = {
+ .bus = &pci_bus_type,
+ .pm = &loongson_spi_dev_pm_ops,
+ },
+};
+module_pci_driver(loongson_spi_pci_driver);
+
+MODULE_DESCRIPTION("Loongson spi pci driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
new file mode 100644
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Platform driver for Loongson SPI Support
+// Copyright (C) 2023 Loongson Technology Corporation Limited
+
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "spi-loongson.h"
+
+static int loongson_spi_platform_probe(struct platform_device *pdev)
+{
+ int ret;
+ void __iomem *reg_base;
+ struct device *dev = &pdev->dev;
+
+ reg_base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(reg_base))
+ return PTR_ERR(reg_base);
+
+ ret = loongson_spi_init_master(dev, reg_base);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to initialize master\n");
+
+ return ret;
+}
+
+static const struct of_device_id loongson_spi_id_table[] = {
+ { .compatible = "loongson,ls2k-spi" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, loongson_spi_id_table);
+
+static struct platform_driver loongson_spi_plat_driver = {
+ .probe = loongson_spi_platform_probe,
+ .driver = {
+ .name = "loongson-spi",
+ .bus = &platform_bus_type,
+ .pm = &loongson_spi_dev_pm_ops,
+ .of_match_table = loongson_spi_id_table,
+ },
+};
+module_platform_driver(loongson_spi_plat_driver);
+
+MODULE_DESCRIPTION("Loongson spi platform driver");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS(SPI_LOONGSON_CORE);
new file mode 100644
@@ -0,0 +1,47 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/* Header File for Loongson SPI Driver. */
+/* Copyright (C) 2023 Loongson Technology Corporation Limited */
+
+#ifndef __LINUX_SPI_LOONGSON_H
+#define __LINUX_SPI_LOONGSON_H
+
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/pm.h>
+#include <linux/spi/spi.h>
+#include <linux/types.h>
+
+#define LOONGSON_SPI_SPCR_REG 0x00
+#define LOONGSON_SPI_SPSR_REG 0x01
+#define LOONGSON_SPI_FIFO_REG 0x02
+#define LOONGSON_SPI_SPER_REG 0x03
+#define LOONGSON_SPI_PARA_REG 0x04
+#define LOONGSON_SPI_SFCS_REG 0x05
+#define LOONGSON_SPI_TIMI_REG 0x06
+
+/* Bits definition for Loongson SPI register */
+#define LOONGSON_SPI_PARA_MEM_EN BIT(0)
+#define LOONGSON_SPI_SPCR_CPHA BIT(2)
+#define LOONGSON_SPI_SPCR_CPOL BIT(3)
+#define LOONGSON_SPI_SPCR_SPE BIT(6)
+#define LOONGSON_SPI_SPSR_WCOL BIT(6)
+#define LOONGSON_SPI_SPSR_SPIF BIT(7)
+
+struct loongson_spi {
+ struct spi_master *master;
+ void __iomem *base;
+ int cs_active;
+ unsigned int hz;
+ unsigned char spcr;
+ unsigned char sper;
+ unsigned char spsr;
+ unsigned char para;
+ unsigned char sfcs;
+ unsigned char timi;
+ unsigned int mode;
+ u64 clk_rate;
+};
+
+int loongson_spi_init_master(struct device *dev, void __iomem *reg);
+extern const struct dev_pm_ops loongson_spi_dev_pm_ops;
+#endif /* __LINUX_SPI_LOONGSON_H */