[v4,2/4] arm64: dts: qcom: Make -cells decimal
Commit Message
The property logically makes sense in decimal, and is the standard used
elsewhere.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
---
Changes since v3:
* Treat all of arm64/qcom at once (Krzysztof)
* Dropped Konrad's RB tag since the scope expanded
Changes since v2:
* Collect tags
Changes since v1:
* New patch (Konrad)
arch/arm64/boot/dts/qcom/ipq6018.dtsi | 2 +-
arch/arm64/boot/dts/qcom/ipq8074.dtsi | 14 +++++++-------
arch/arm64/boot/dts/qcom/msm8953.dtsi | 4 ++--
arch/arm64/boot/dts/qcom/qcs404-evb-4000.dts | 4 ++--
arch/arm64/boot/dts/qcom/sa8155p-adp.dts | 4 ++--
5 files changed, 14 insertions(+), 14 deletions(-)
Comments
On 01/05/2023 23:24, Andrew Halaney wrote:
> The property logically makes sense in decimal, and is the standard used
> elsewhere.
>
> Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> Signed-off-by: Andrew Halaney <ahalaney@redhat.com>
> ---
>
> Changes since v3:
> * Treat all of arm64/qcom at once (Krzysztof)
> * Dropped Konrad's RB tag since the scope expanded
> Changes since v2:
> * Collect tags
> Changes since v1:
> * New patch (Konrad)
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
@@ -571,7 +571,7 @@ intc: interrupt-controller@b000000 {
#address-cells = <2>;
#size-cells = <2>;
interrupt-controller;
- #interrupt-cells = <0x3>;
+ #interrupt-cells = <3>;
reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/
<0x0 0x0b002000 0x0 0x1000>, /*GICC*/
<0x0 0x0b001000 0x0 0x1000>, /*GICH*/
@@ -29,8 +29,8 @@ xo: xo {
};
cpus {
- #address-cells = <0x1>;
- #size-cells = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
CPU0: cpu@0 {
device_type = "cpu";
@@ -106,8 +106,8 @@ scm {
};
soc: soc {
- #address-cells = <0x1>;
- #size-cells = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
ranges = <0 0 0 0xffffffff>;
compatible = "simple-bus";
@@ -321,9 +321,9 @@ tlmm: pinctrl@1000000 {
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
gpio-ranges = <&tlmm 0 0 70>;
- #gpio-cells = <0x2>;
+ #gpio-cells = <2>;
interrupt-controller;
- #interrupt-cells = <0x2>;
+ #interrupt-cells = <2>;
serial_4_pins: serial4-state {
pins = "gpio23", "gpio24";
@@ -666,7 +666,7 @@ intc: interrupt-controller@b000000 {
#address-cells = <1>;
#size-cells = <1>;
interrupt-controller;
- #interrupt-cells = <0x3>;
+ #interrupt-cells = <3>;
reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>;
ranges = <0 0xb00a000 0xffd>;
@@ -1505,8 +1505,8 @@ apcs: mailbox@b011000 {
timer@b120000 {
compatible = "arm,armv7-timer-mem";
reg = <0x0b120000 0x1000>;
- #address-cells = <0x01>;
- #size-cells = <0x01>;
+ #address-cells = <1>;
+ #size-cells = <1>;
ranges;
frame@b121000 {
@@ -27,8 +27,8 @@ ðernet {
phy-handle = <&phy1>;
phy-mode = "rgmii";
mdio {
- #address-cells = <0x1>;
- #size-cells = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy1: phy@4 {
compatible = "ethernet-phy-ieee802.3-c22";
@@ -353,8 +353,8 @@ ðernet {
mdio {
compatible = "snps,dwmac-mdio";
- #address-cells = <0x1>;
- #size-cells = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
/* Micrel KSZ9031RNZ PHY */
rgmii_phy: phy@7 {