@@ -13175,9 +13175,11 @@ MEDIATEK SWITCH DRIVER
M: Sean Wang <sean.wang@mediatek.com>
M: Landen Chao <Landen.Chao@mediatek.com>
M: DENG Qingfang <dqfext@gmail.com>
+M: Daniel Golle <daniel@makrotopia.org>
L: netdev@vger.kernel.org
S: Maintained
F: drivers/net/dsa/mt7530-mdio.c
+F: drivers/net/dsa/mt7530-mmio.c
F: drivers/net/dsa/mt7530.*
F: net/dsa/tag_mtk.c
@@ -39,6 +39,7 @@ config NET_DSA_MT7530
select NET_DSA_TAG_MTK
select MEDIATEK_GE_PHY
imply NET_DSA_MT7530_MDIO
+ imply NET_DSA_MT7530_MMIO
help
This enables support for the MediaTek MT7530 and MT7531 Ethernet
switch chips. Multi-chip module MT7530 in MT7621AT, MT7621DAT,
@@ -55,6 +56,17 @@ config NET_DSA_MT7530_MDIO
module MT7530 which can be found in the MT7621AT, MT7621DAT,
MT7621ST and MT7623AI SoCs.
+config NET_DSA_MT7530_MMIO
+ tristate "MediaTek MT7530 MMIO interface driver"
+ depends on NET_DSA_MT7530
+ depends on HAS_IOMEM
+ help
+ This enables support for the built-in Ethernet switch found
+ in the MediaTek MT7988 SoC.
+ The switch is a similar design as MT7531, but the switch registers
+ are directly mapped into the SoCs register space rather than being
+ accessible via MDIO.
+
config NET_DSA_MV88E6060
tristate "Marvell 88E6060 ethernet switch chip support"
select NET_DSA_TAG_TRAILER
@@ -8,6 +8,7 @@ endif
obj-$(CONFIG_NET_DSA_LANTIQ_GSWIP) += lantiq_gswip.o
obj-$(CONFIG_NET_DSA_MT7530) += mt7530.o
obj-$(CONFIG_NET_DSA_MT7530_MDIO) += mt7530-mdio.o
+obj-$(CONFIG_NET_DSA_MT7530_MMIO) += mt7530-mmio.o
obj-$(CONFIG_NET_DSA_MV88E6060) += mv88e6060.o
obj-$(CONFIG_NET_DSA_RZN1_A5PSW) += rzn1_a5psw.o
obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o
new file mode 100644
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <net/dsa.h>
+
+#include "mt7530.h"
+
+static const struct of_device_id mt7988_of_match[] = {
+ { .compatible = "mediatek,mt7988-switch", .data = &mt753x_table[ID_MT7988], },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mt7988_of_match);
+
+static int
+mt7988_probe(struct platform_device *pdev)
+{
+ static struct regmap_config *sw_regmap_config;
+ struct mt7530_priv *priv;
+ void __iomem *base_addr;
+ int ret;
+
+ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ priv->bus = NULL;
+ priv->dev = &pdev->dev;
+
+ ret = mt7530_probe_common(priv);
+ if (ret)
+ return ret;
+
+ priv->rstc = devm_reset_control_get(&pdev->dev, NULL);
+ if (IS_ERR(priv->rstc)) {
+ dev_err(&pdev->dev, "Couldn't get our reset line\n");
+ return PTR_ERR(priv->rstc);
+ }
+
+ base_addr = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base_addr)) {
+ dev_err(&pdev->dev, "cannot request I/O memory space\n");
+ return -ENXIO;
+ }
+
+ sw_regmap_config = devm_kzalloc(&pdev->dev, sizeof(*sw_regmap_config), GFP_KERNEL);
+ if (!sw_regmap_config)
+ return -ENOMEM;
+
+ sw_regmap_config->name = "switch";
+ sw_regmap_config->reg_bits = 16;
+ sw_regmap_config->val_bits = 32;
+ sw_regmap_config->reg_stride = 4;
+ sw_regmap_config->max_register = MT7530_CREV;
+ priv->regmap = devm_regmap_init_mmio(&pdev->dev, base_addr, sw_regmap_config);
+ if (IS_ERR(priv->regmap))
+ return PTR_ERR(priv->regmap);
+
+ return dsa_register_switch(priv->ds);
+}
+
+static int
+mt7988_remove(struct platform_device *pdev)
+{
+ struct mt7530_priv *priv = platform_get_drvdata(pdev);
+
+ if (priv)
+ mt7530_remove_common(priv);
+
+ return 0;
+}
+
+static void mt7988_shutdown(struct platform_device *pdev)
+{
+ struct mt7530_priv *priv = platform_get_drvdata(pdev);
+
+ if (!priv)
+ return;
+
+ dsa_switch_shutdown(priv->ds);
+
+ dev_set_drvdata(&pdev->dev, NULL);
+}
+
+static struct platform_driver mt7988_platform_driver = {
+ .probe = mt7988_probe,
+ .remove = mt7988_remove,
+ .shutdown = mt7988_shutdown,
+ .driver = {
+ .name = "mt7530-mmio",
+ .of_match_table = mt7988_of_match,
+ },
+};
+module_platform_driver(mt7988_platform_driver);
+
+MODULE_AUTHOR("Daniel Golle <daniel@makrotopia.org>");
+MODULE_DESCRIPTION("Driver for Mediatek MT7530 Switch (MMIO)");
+MODULE_LICENSE("GPL");
@@ -1981,6 +1981,47 @@ static const struct irq_domain_ops mt7530_irq_domain_ops = {
.xlate = irq_domain_xlate_onecell,
};
+static void
+mt7988_irq_mask(struct irq_data *d)
+{
+ struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
+
+ priv->irq_enable &= ~BIT(d->hwirq);
+ mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable);
+}
+
+static void
+mt7988_irq_unmask(struct irq_data *d)
+{
+ struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
+
+ priv->irq_enable |= BIT(d->hwirq);
+ mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable);
+}
+
+static struct irq_chip mt7988_irq_chip = {
+ .name = KBUILD_MODNAME,
+ .irq_mask = mt7988_irq_mask,
+ .irq_unmask = mt7988_irq_unmask,
+};
+
+static int
+mt7988_irq_map(struct irq_domain *domain, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ irq_set_chip_data(irq, domain->host_data);
+ irq_set_chip_and_handler(irq, &mt7988_irq_chip, handle_simple_irq);
+ irq_set_nested_thread(irq, true);
+ irq_set_noprobe(irq);
+
+ return 0;
+}
+
+static const struct irq_domain_ops mt7988_irq_domain_ops = {
+ .map = mt7988_irq_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
static void
mt7530_setup_mdio_irq(struct mt7530_priv *priv)
{
@@ -2015,8 +2056,15 @@ mt7530_setup_irq(struct mt7530_priv *priv)
return priv->irq ? : -EINVAL;
}
- priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
- &mt7530_irq_domain_ops, priv);
+ if (priv->id == ID_MT7988)
+ priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
+ &mt7988_irq_domain_ops,
+ priv);
+ else
+ priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
+ &mt7530_irq_domain_ops,
+ priv);
+
if (!priv->irq_domain) {
dev_err(dev, "failed to create IRQ domain\n");
return -ENOMEM;
@@ -2511,6 +2559,25 @@ static void mt7531_mac_port_get_caps(struct dsa_switch *ds, int port,
}
}
+static void mt7988_mac_port_get_caps(struct dsa_switch *ds, int port,
+ struct phylink_config *config)
+{
+ phy_interface_zero(config->supported_interfaces);
+
+ switch (port) {
+ case 0 ... 4: /* Internal phy */
+ __set_bit(PHY_INTERFACE_MODE_INTERNAL,
+ config->supported_interfaces);
+ break;
+
+ case 6:
+ __set_bit(PHY_INTERFACE_MODE_INTERNAL,
+ config->supported_interfaces);
+ config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+ MAC_10000FD;
+ }
+}
+
static int
mt753x_pad_setup(struct dsa_switch *ds, const struct phylink_link_state *state)
{
@@ -2586,6 +2653,17 @@ static bool mt753x_is_mac_port(u32 port)
return (port == 5 || port == 6);
}
+static int
+mt7988_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
+ phy_interface_t interface)
+{
+ if (dsa_is_cpu_port(ds, port) &&
+ interface == PHY_INTERFACE_MODE_INTERNAL)
+ return 0;
+
+ return -EINVAL;
+}
+
static int
mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
phy_interface_t interface)
@@ -2656,7 +2734,8 @@ mt753x_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
switch (port) {
case 0 ... 4: /* Internal phy */
- if (state->interface != PHY_INTERFACE_MODE_GMII)
+ if (state->interface != PHY_INTERFACE_MODE_GMII &&
+ state->interface != PHY_INTERFACE_MODE_INTERNAL)
goto unsupported;
break;
case 5: /* 2nd cpu port with phy of port 0 or 4 / external phy */
@@ -2734,7 +2813,8 @@ static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port,
/* MT753x MAC works in 1G full duplex mode for all up-clocked
* variants.
*/
- if (interface == PHY_INTERFACE_MODE_TRGMII ||
+ if (interface == PHY_INTERFACE_MODE_INTERNAL ||
+ interface == PHY_INTERFACE_MODE_TRGMII ||
(phy_interface_mode_is_8023z(interface))) {
speed = SPEED_1000;
duplex = DUPLEX_FULL;
@@ -2814,6 +2894,21 @@ mt7531_cpu_port_config(struct dsa_switch *ds, int port)
return 0;
}
+static int
+mt7988_cpu_port_config(struct dsa_switch *ds, int port)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ mt7530_write(priv, MT7530_PMCR_P(port),
+ PMCR_CPU_PORT_SETTING(priv->id));
+
+ mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED,
+ PHY_INTERFACE_MODE_INTERNAL, NULL,
+ SPEED_10000, DUPLEX_FULL, true, true);
+
+ return 0;
+}
+
static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port,
struct phylink_config *config)
{
@@ -2956,6 +3051,27 @@ static int mt753x_set_mac_eee(struct dsa_switch *ds, int port,
return 0;
}
+static int mt7988_pad_setup(struct dsa_switch *ds, phy_interface_t interface)
+{
+ return 0;
+}
+
+static int mt7988_setup(struct dsa_switch *ds)
+{
+ struct mt7530_priv *priv = ds->priv;
+
+ /* Reset the switch */
+ reset_control_assert(priv->rstc);
+ usleep_range(20, 50);
+ reset_control_deassert(priv->rstc);
+ usleep_range(20, 50);
+
+ /* Reset the switch PHYs */
+ mt7530_write(priv, MT7530_SYS_CTRL, SYS_CTRL_PHY_RST);
+
+ return mt7531_setup_common(ds);
+}
+
const struct dsa_switch_ops mt7530_switch_ops = {
.get_tag_protocol = mtk_get_tag_protocol,
.setup = mt753x_setup,
@@ -3030,6 +3146,19 @@ const struct mt753x_info mt753x_table[] = {
.mac_port_get_caps = mt7531_mac_port_get_caps,
.mac_port_config = mt7531_mac_config,
},
+ [ID_MT7988] = {
+ .id = ID_MT7988,
+ .pcs_ops = &mt7530_pcs_ops,
+ .sw_setup = mt7988_setup,
+ .phy_read_c22 = mt7531_ind_c22_phy_read,
+ .phy_write_c22 = mt7531_ind_c22_phy_write,
+ .phy_read_c45 = mt7531_ind_c45_phy_read,
+ .phy_write_c45 = mt7531_ind_c45_phy_write,
+ .pad_setup = mt7988_pad_setup,
+ .cpu_port_config = mt7988_cpu_port_config,
+ .mac_port_get_caps = mt7988_mac_port_get_caps,
+ .mac_port_config = mt7988_mac_config,
+ },
};
EXPORT_SYMBOL_GPL(mt753x_table);
@@ -18,6 +18,7 @@ enum mt753x_id {
ID_MT7530 = 0,
ID_MT7621 = 1,
ID_MT7531 = 2,
+ ID_MT7988 = 3,
};
#define NUM_TRGMII_CTRL 5
@@ -54,11 +55,11 @@ enum mt753x_id {
#define MT7531_MIRROR_PORT_SET(x) (((x) & MIRROR_MASK) << 16)
#define MT7531_CPU_PMAP_MASK GENMASK(7, 0)
-#define MT753X_MIRROR_REG(id) (((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_REG(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \
MT7531_CFC : MT7530_MFC)
-#define MT753X_MIRROR_EN(id) (((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_EN(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \
MT7531_MIRROR_EN : MIRROR_EN)
-#define MT753X_MIRROR_MASK(id) (((id) == ID_MT7531) ? \
+#define MT753X_MIRROR_MASK(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \
MT7531_MIRROR_MASK : MIRROR_MASK)
/* Registers for BPDU and PAE frame control*/
@@ -295,9 +296,8 @@ enum mt7530_vlan_port_acc_frm {
MT7531_FORCE_DPX | \
MT7531_FORCE_RX_FC | \
MT7531_FORCE_TX_FC)
-#define PMCR_FORCE_MODE_ID(id) (((id) == ID_MT7531) ? \
- MT7531_FORCE_MODE : \
- PMCR_FORCE_MODE)
+#define PMCR_FORCE_MODE_ID(id) ((((id) == ID_MT7531) || ((id) == ID_MT7988)) ? \
+ MT7531_FORCE_MODE : PMCR_FORCE_MODE)
#define PMCR_LINK_SETTINGS_MASK (PMCR_TX_EN | PMCR_FORCE_SPEED_1000 | \
PMCR_RX_EN | PMCR_FORCE_SPEED_100 | \
PMCR_TX_FC_EN | PMCR_RX_FC_EN | \