diff mbox series

[v5,4/7] phy: starfive: Add JH7110 PCIE 2.0 PHY driver

Message ID 20230420110052.3182-5-minda.chen@starfivetech.com
State New
Headers
Series Add JH7110 USB and USB PHY driver support |

Commit Message

Minda Chen April 20, 2023, 11 a.m. UTC 
  Add Starfive JH7110 SoC PCIe 2.0 PHY driver support.
PCIe 2.0 PHY default connect to PCIe controller.
But pcie0 PHY can connect to USB 3.0 controlller.

Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
---
 MAINTAINERS                            |   4 +-
 drivers/phy/starfive/Kconfig           |  11 ++
 drivers/phy/starfive/Makefile          |   1 +
 drivers/phy/starfive/phy-jh7110-pcie.c | 202 +++++++++++++++++++++++++
 4 files changed, 217 insertions(+), 1 deletion(-)
 create mode 100644 drivers/phy/starfive/phy-jh7110-pcie.c

Comments

Roger Quadros April 24, 2023, 9:23 a.m. UTC | #1 
On 20/04/2023 14:00, Minda Chen wrote:
> Add Starfive JH7110 SoC PCIe 2.0 PHY driver support.
> PCIe 2.0 PHY default connect to PCIe controller.
> But pcie0 PHY can connect to USB 3.0 controlller.

s/controlller/controller

> 
> Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
> ---
>  MAINTAINERS                            |   4 +-
>  drivers/phy/starfive/Kconfig           |  11 ++
>  drivers/phy/starfive/Makefile          |   1 +
>  drivers/phy/starfive/phy-jh7110-pcie.c | 202 +++++++++++++++++++++++++
>  4 files changed, 217 insertions(+), 1 deletion(-)
>  create mode 100644 drivers/phy/starfive/phy-jh7110-pcie.c
> 
> diff --git a/MAINTAINERS b/MAINTAINERS
> index c09ea66dcd5a..8e0f755ba91b 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -19968,10 +19968,12 @@ M:	William Qiu <william.qiu@starfivetech.com>
>  S:	Supported
>  F:	Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
>  
> -STARFIVE JH71X0 USB PHY DRIVER
> +STARFIVE JH71X0 PCIE AND USB PHY DRIVER
>  M:	Minda Chen <minda.chen@starfivetech.com>
>  S:	Supported
> +F:	Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml
>  F:	Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml
> +F:	drivers/phy/starfive/phy-jh7110-pcie.c
>  F:	drivers/phy/starfive/phy-jh7110-usb.c
>  
>  STATIC BRANCH/CALL
> diff --git a/drivers/phy/starfive/Kconfig b/drivers/phy/starfive/Kconfig
> index 2c013c390dee..c21c21d284a6 100644
> --- a/drivers/phy/starfive/Kconfig
> +++ b/drivers/phy/starfive/Kconfig
> @@ -12,6 +12,17 @@ config PHY_STARFIVE_DPHY_RX
>  	  system. If M is selected, the module will be called
>  	  phy-starfive-dphy-rx.
>  
> +config PHY_STARFIVE_JH7110_PCIE
> +	tristate "Starfive JH7110 PCIE 2.0/USB 3.0 PHY support"
> +	depends on USB_SUPPORT

What if system has PCIE and no USB. Then they can't use this PHY
as it cannot be built?

> +	select GENERIC_PHY
> +	select USB_PHY
> +	help
> +	  Enable this to support the StarFive PCIe 2.0 PHY,
> +	  or used as USB 3.0 PHY.
> +	  If M is selected, the module will be called
> +	  phy-jh7110-pcie.ko.
> +
>  config PHY_STARFIVE_JH7110_USB
>  	tristate "Starfive JH7110 USB 2.0 PHY support"
>  	depends on USB_SUPPORT
> diff --git a/drivers/phy/starfive/Makefile b/drivers/phy/starfive/Makefile
> index 176443852f4d..03a55aad53a2 100644
> --- a/drivers/phy/starfive/Makefile
> +++ b/drivers/phy/starfive/Makefile
> @@ -1,3 +1,4 @@
>  # SPDX-License-Identifier: GPL-2.0
>  obj-$(CONFIG_PHY_STARFIVE_DPHY_RX)      += phy-starfive-dphy-rx.o
> +obj-$(CONFIG_PHY_STARFIVE_JH7110_PCIE)	+= phy-jh7110-pcie.o
>  obj-$(CONFIG_PHY_STARFIVE_JH7110_USB)	+= phy-jh7110-usb.o
> diff --git a/drivers/phy/starfive/phy-jh7110-pcie.c b/drivers/phy/starfive/phy-jh7110-pcie.c
> new file mode 100644
> index 000000000000..fe029daef62e
> --- /dev/null
> +++ b/drivers/phy/starfive/phy-jh7110-pcie.c
> @@ -0,0 +1,202 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * StarFive JH7110 PCIe 2.0 PHY driver
> + *
> + * Copyright (C) 2023 StarFive Technology Co., Ltd.
> + * Author: Minda Chen <minda.chen@starfivetech.com>
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#define PCIE_KVCO_LEVEL_OFF		(0x28)
> +#define PCIE_USB3_PHY_PLL_CTL_OFF	(0x7c)
> +#define PCIE_KVCO_TUNE_SIGNAL_OFF	(0x80)

Brackets not required.

> +#define PCIE_USB3_PHY_ENABLE		BIT(4)
> +#define PHY_KVCO_FINE_TUNE_LEVEL	0x91
> +#define PHY_KVCO_FINE_TUNE_SIGNALS	0xc
> +
> +#define USB_PDRSTN_SPLIT		BIT(17)
> +
> +#define PCIE_PHY_MODE			BIT(20)
> +#define PCIE_PHY_MODE_MASK		GENMASK(21, 20)
> +#define PCIE_USB3_BUS_WIDTH_MASK	GENMASK(3, 2)
> +#define PCIE_USB3_RATE_MASK		GENMASK(6, 5)
> +#define PCIE_USB3_RX_STANDBY_MASK	BIT(7)
> +#define PCIE_USB3_PHY_ENABLE		BIT(4)
> +
> +struct jh7110_pcie_phy {
> +	struct phy *phy;
> +	struct regmap *stg_syscon;
> +	struct regmap *sys_syscon;
> +	void __iomem *regs;
> +	u32 sys_phy_connect;
> +	u32 stg_pcie_mode;
> +	u32 stg_pcie_usb;
> +	enum phy_mode mode;
> +};
> +
> +static int jh7110_usb3_mode_set(struct jh7110_pcie_phy *data)
> +{
> +	if (!data->stg_syscon || !data->sys_syscon) {
> +		dev_info(&data->phy->dev, "don't support usb3 mode\n");

s/don't/doesn't

dev_err()

> +		return -EINVAL;
> +	}
> +
> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_mode,
> +			   PCIE_PHY_MODE_MASK, PCIE_PHY_MODE);
> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
> +			   PCIE_USB3_BUS_WIDTH_MASK, 0);
> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
> +			   PCIE_USB3_RATE_MASK, 0);
> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
> +			   PCIE_USB3_RX_STANDBY_MASK, 0);
> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
> +			   PCIE_USB3_PHY_ENABLE, PCIE_USB3_PHY_ENABLE);
> +
> +	/* Connect usb 3.0 phy mode */
> +	regmap_update_bits(data->sys_syscon, data->sys_phy_connect,
> +			   USB_PDRSTN_SPLIT, 0);
> +
> +	/* Configuare spread-spectrum mode: down-spread-spectrum */
> +	writel(PCIE_USB3_PHY_ENABLE, data->regs + PCIE_USB3_PHY_PLL_CTL_OFF);
> +
> +	return 0;
> +}
> +
> +static void jh7110_pcie_mode_set(struct jh7110_pcie_phy *phy)
> +{
> +	/* PCIe Multi-PHY PLL KVCO Gain fine tune settings: */
> +	writel(PHY_KVCO_FINE_TUNE_LEVEL, phy->regs + PCIE_KVCO_LEVEL_OFF);
> +	writel(PHY_KVCO_FINE_TUNE_SIGNALS, phy->regs + PCIE_KVCO_TUNE_SIGNAL_OFF);

In cases where PHY can be connected to both USB and PCIe don't you have to
make sure PHY is connected to PCIe controller by setting data->sys_syscon
and data->stg_syscon appropriately?

> +}
> +
> +static int jh7110_pcie_phy_set_mode(struct phy *_phy,
> +				    enum phy_mode mode, int submode)
> +{
> +	struct jh7110_pcie_phy *phy = phy_get_drvdata(_phy);
> +	int ret;
> +
> +	if (mode == phy->mode)
> +		return 0;
> +
> +	switch (mode) {
> +	case PHY_MODE_USB_HOST:
> +	case PHY_MODE_USB_DEVICE:
> +	case PHY_MODE_USB_OTG:
> +		ret = jh7110_usb3_mode_set(phy);
> +		if (ret)
> +			return ret;
> +		break;
> +	case PHY_MODE_PCIE:
> +		jh7110_pcie_mode_set(phy);
> +		break;
> +	default:
> +		return -EINVAL;
> +	}
> +
> +	dev_info(&_phy->dev, "Changing phy mode to %d\n", mode);

dev_dbg()?

> +	phy->mode = mode;
> +
> +	return 0;
> +}
> +
> +static int jh7110_pcie_phy_init(struct phy *_phy)
> +{
> +	return 0;
> +}
> +
> +static int jh7110_pcie_phy_exit(struct phy *_phy)
> +{
> +	return 0;
> +}
> +
> +static const struct phy_ops jh7110_pcie_phy_ops = {
> +	.init		= jh7110_pcie_phy_init,
> +	.exit		= jh7110_pcie_phy_exit,

As you are not doing anything in init/exit, you don't have to set them.

> +	.set_mode	= jh7110_pcie_phy_set_mode,
> +	.owner		= THIS_MODULE,
> +};
> +
> +static int jh7110_pcie_phy_probe(struct platform_device *pdev)
> +{
> +	struct jh7110_pcie_phy *phy;
> +	struct device *dev = &pdev->dev;
> +	struct phy_provider *phy_provider;
> +	u32 args[2];
> +
> +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
> +	if (!phy)
> +		return -ENOMEM;
> +
> +	phy->regs = devm_platform_ioremap_resource(pdev, 0);
> +	if (IS_ERR(phy->regs))
> +		return PTR_ERR(phy->regs);
> +
> +	phy->phy = devm_phy_create(dev, NULL, &jh7110_pcie_phy_ops);
> +	if (IS_ERR(phy->phy))
> +		return dev_err_probe(dev, PTR_ERR(phy->regs),
> +			"Failed to map phy base\n");
> +
> +	phy->sys_syscon =
> +		syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
> +						     "starfive,sys-syscon",
> +						     1, args);
> +
> +	if (!IS_ERR_OR_NULL(phy->sys_syscon))
> +		phy->sys_phy_connect = args[0];
> +	else
> +		phy->sys_syscon = NULL;
> +
> +	phy->stg_syscon =
> +		syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
> +						     "starfive,stg-syscon",
> +						     2, args);
> +
> +	if (!IS_ERR_OR_NULL(phy->stg_syscon)) {
> +		phy->stg_pcie_mode = args[0];
> +		phy->stg_pcie_usb = args[1];
> +	} else {
> +		phy->stg_syscon = NULL;
> +	}
> +
> +	platform_set_drvdata(pdev, phy);
> +	phy_set_drvdata(phy->phy, phy);
> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
> +
> +	return PTR_ERR_OR_ZERO(phy_provider);
> +}
> +
> +static int jh7110_pcie_phy_remove(struct platform_device *pdev)
> +{
> +	platform_set_drvdata(pdev, NULL);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id jh7110_pcie_phy_of_match[] = {
> +	{ .compatible = "starfive,jh7110-pcie-phy" },
> +	{ /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, jh7110_pcie_phy_of_match);
> +
> +static struct platform_driver jh7110_pcie_phy_driver = {
> +	.probe	= jh7110_pcie_phy_probe,
> +	.remove	= jh7110_pcie_phy_remove,
> +	.driver = {
> +		.of_match_table	= jh7110_pcie_phy_of_match,
> +		.name  = "jh7110-pcie-phy",
> +	}
> +};
> +module_platform_driver(jh7110_pcie_phy_driver);
> +
> +MODULE_DESCRIPTION("StarFive JH7110 PCIe 2.0 PHY driver");
> +MODULE_AUTHOR("Minda Chen <minda.chen@starfivetech.com>");
> +MODULE_LICENSE("GPL");

cheers,
-roger
Minda Chen April 24, 2023, 11:14 a.m. UTC | #2 
On 2023/4/24 17:23, Roger Quadros wrote:
> 
> 
> On 20/04/2023 14:00, Minda Chen wrote:
>> Add Starfive JH7110 SoC PCIe 2.0 PHY driver support.
>> PCIe 2.0 PHY default connect to PCIe controller.
>> But pcie0 PHY can connect to USB 3.0 controlller.
> 
> s/controlller/controller
> 
ok
>> 
>> Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
>> ---
>>  MAINTAINERS                            |   4 +-
>>  drivers/phy/starfive/Kconfig           |  11 ++
>>  drivers/phy/starfive/Makefile          |   1 +
>>  drivers/phy/starfive/phy-jh7110-pcie.c | 202 +++++++++++++++++++++++++
>>  4 files changed, 217 insertions(+), 1 deletion(-)
>>  create mode 100644 drivers/phy/starfive/phy-jh7110-pcie.c
>> 
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index c09ea66dcd5a..8e0f755ba91b 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -19968,10 +19968,12 @@ M:	William Qiu <william.qiu@starfivetech.com>
>>  S:	Supported
>>  F:	Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
>>  
>> -STARFIVE JH71X0 USB PHY DRIVER
>> +STARFIVE JH71X0 PCIE AND USB PHY DRIVER
>>  M:	Minda Chen <minda.chen@starfivetech.com>
>>  S:	Supported
>> +F:	Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml
>>  F:	Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml
>> +F:	drivers/phy/starfive/phy-jh7110-pcie.c
>>  F:	drivers/phy/starfive/phy-jh7110-usb.c
>>  
>>  STATIC BRANCH/CALL
>> diff --git a/drivers/phy/starfive/Kconfig b/drivers/phy/starfive/Kconfig
>> index 2c013c390dee..c21c21d284a6 100644
>> --- a/drivers/phy/starfive/Kconfig
>> +++ b/drivers/phy/starfive/Kconfig
>> @@ -12,6 +12,17 @@ config PHY_STARFIVE_DPHY_RX
>>  	  system. If M is selected, the module will be called
>>  	  phy-starfive-dphy-rx.
>>  
>> +config PHY_STARFIVE_JH7110_PCIE
>> +	tristate "Starfive JH7110 PCIE 2.0/USB 3.0 PHY support"
>> +	depends on USB_SUPPORT
> 
> What if system has PCIE and no USB. Then they can't use this PHY
> as it cannot be built?
> 
ok, I will delete it
>> +	select GENERIC_PHY
>> +	select USB_PHY
>> +	help
>> +	  Enable this to support the StarFive PCIe 2.0 PHY,
>> +	  or used as USB 3.0 PHY.
>> +	  If M is selected, the module will be called
>> +	  phy-jh7110-pcie.ko.
>> +
>>  config PHY_STARFIVE_JH7110_USB
>>  	tristate "Starfive JH7110 USB 2.0 PHY support"
>>  	depends on USB_SUPPORT
>> diff --git a/drivers/phy/starfive/Makefile b/drivers/phy/starfive/Makefile
>> index 176443852f4d..03a55aad53a2 100644
>> --- a/drivers/phy/starfive/Makefile
>> +++ b/drivers/phy/starfive/Makefile
>> @@ -1,3 +1,4 @@
>>  # SPDX-License-Identifier: GPL-2.0
>>  obj-$(CONFIG_PHY_STARFIVE_DPHY_RX)      += phy-starfive-dphy-rx.o
>> +obj-$(CONFIG_PHY_STARFIVE_JH7110_PCIE)	+= phy-jh7110-pcie.o
>>  obj-$(CONFIG_PHY_STARFIVE_JH7110_USB)	+= phy-jh7110-usb.o
>> diff --git a/drivers/phy/starfive/phy-jh7110-pcie.c b/drivers/phy/starfive/phy-jh7110-pcie.c
>> new file mode 100644
>> index 000000000000..fe029daef62e
>> --- /dev/null
>> +++ b/drivers/phy/starfive/phy-jh7110-pcie.c
>> @@ -0,0 +1,202 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * StarFive JH7110 PCIe 2.0 PHY driver
>> + *
>> + * Copyright (C) 2023 StarFive Technology Co., Ltd.
>> + * Author: Minda Chen <minda.chen@starfivetech.com>
>> + */
>> +
>> +#include <linux/bits.h>
>> +#include <linux/clk.h>
>> +#include <linux/err.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +
>> +#define PCIE_KVCO_LEVEL_OFF		(0x28)
>> +#define PCIE_USB3_PHY_PLL_CTL_OFF	(0x7c)
>> +#define PCIE_KVCO_TUNE_SIGNAL_OFF	(0x80)
> 
> Brackets not required.
> 
ok
>> +#define PCIE_USB3_PHY_ENABLE		BIT(4)
>> +#define PHY_KVCO_FINE_TUNE_LEVEL	0x91
>> +#define PHY_KVCO_FINE_TUNE_SIGNALS	0xc
>> +
>> +#define USB_PDRSTN_SPLIT		BIT(17)
>> +
>> +#define PCIE_PHY_MODE			BIT(20)
>> +#define PCIE_PHY_MODE_MASK		GENMASK(21, 20)
>> +#define PCIE_USB3_BUS_WIDTH_MASK	GENMASK(3, 2)
>> +#define PCIE_USB3_RATE_MASK		GENMASK(6, 5)
>> +#define PCIE_USB3_RX_STANDBY_MASK	BIT(7)
>> +#define PCIE_USB3_PHY_ENABLE		BIT(4)
>> +
>> +struct jh7110_pcie_phy {
>> +	struct phy *phy;
>> +	struct regmap *stg_syscon;
>> +	struct regmap *sys_syscon;
>> +	void __iomem *regs;
>> +	u32 sys_phy_connect;
>> +	u32 stg_pcie_mode;
>> +	u32 stg_pcie_usb;
>> +	enum phy_mode mode;
>> +};
>> +
>> +static int jh7110_usb3_mode_set(struct jh7110_pcie_phy *data)
>> +{
>> +	if (!data->stg_syscon || !data->sys_syscon) {
>> +		dev_info(&data->phy->dev, "don't support usb3 mode\n");
> 
> s/don't/doesn't
> 
> dev_err()
> 
>> +		return -EINVAL;
>> +	}
>> +
>> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_mode,
>> +			   PCIE_PHY_MODE_MASK, PCIE_PHY_MODE);
>> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
>> +			   PCIE_USB3_BUS_WIDTH_MASK, 0);
>> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
>> +			   PCIE_USB3_RATE_MASK, 0);
>> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
>> +			   PCIE_USB3_RX_STANDBY_MASK, 0);
>> +	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
>> +			   PCIE_USB3_PHY_ENABLE, PCIE_USB3_PHY_ENABLE);
>> +
>> +	/* Connect usb 3.0 phy mode */
>> +	regmap_update_bits(data->sys_syscon, data->sys_phy_connect,
>> +			   USB_PDRSTN_SPLIT, 0);
>> +
>> +	/* Configuare spread-spectrum mode: down-spread-spectrum */
>> +	writel(PCIE_USB3_PHY_ENABLE, data->regs + PCIE_USB3_PHY_PLL_CTL_OFF);
>> +
>> +	return 0;
>> +}
>> +
>> +static void jh7110_pcie_mode_set(struct jh7110_pcie_phy *phy)
>> +{
>> +	/* PCIe Multi-PHY PLL KVCO Gain fine tune settings: */
>> +	writel(PHY_KVCO_FINE_TUNE_LEVEL, phy->regs + PCIE_KVCO_LEVEL_OFF);
>> +	writel(PHY_KVCO_FINE_TUNE_SIGNALS, phy->regs + PCIE_KVCO_TUNE_SIGNAL_OFF);
> 
> In cases where PHY can be connected to both USB and PCIe don't you have to
> make sure PHY is connected to PCIe controller by setting data->sys_syscon
> and data->stg_syscon appropriately?
> 
PHY default connect to pcie. In our products so far, The PHY connected to either USB or PCIe. So I don't set the syscon register.
But the case of PHY can be connected to both USB and PCIe maybe existed. I will add this case.
>> +}
>> +
>> +static int jh7110_pcie_phy_set_mode(struct phy *_phy,
>> +				    enum phy_mode mode, int submode)
>> +{
>> +	struct jh7110_pcie_phy *phy = phy_get_drvdata(_phy);
>> +	int ret;
>> +
>> +	if (mode == phy->mode)
>> +		return 0;
>> +
>> +	switch (mode) {
>> +	case PHY_MODE_USB_HOST:
>> +	case PHY_MODE_USB_DEVICE:
>> +	case PHY_MODE_USB_OTG:
>> +		ret = jh7110_usb3_mode_set(phy);
>> +		if (ret)
>> +			return ret;
>> +		break;
>> +	case PHY_MODE_PCIE:
>> +		jh7110_pcie_mode_set(phy);
>> +		break;
>> +	default:
>> +		return -EINVAL;
>> +	}
>> +
>> +	dev_info(&_phy->dev, "Changing phy mode to %d\n", mode);
> 
> dev_dbg()?
> 
ok
>> +	phy->mode = mode;
>> +
>> +	return 0;
>> +}
>> +
>> +static int jh7110_pcie_phy_init(struct phy *_phy)
>> +{
>> +	return 0;
>> +}
>> +
>> +static int jh7110_pcie_phy_exit(struct phy *_phy)
>> +{
>> +	return 0;
>> +}
>> +
>> +static const struct phy_ops jh7110_pcie_phy_ops = {
>> +	.init		= jh7110_pcie_phy_init,
>> +	.exit		= jh7110_pcie_phy_exit,
> 
> As you are not doing anything in init/exit, you don't have to set them.
> 
ok
>> +	.set_mode	= jh7110_pcie_phy_set_mode,
>> +	.owner		= THIS_MODULE,
>> +};
>> +
>> +static int jh7110_pcie_phy_probe(struct platform_device *pdev)
>> +{
>> +	struct jh7110_pcie_phy *phy;
>> +	struct device *dev = &pdev->dev;
>> +	struct phy_provider *phy_provider;
>> +	u32 args[2];
>> +
>> +	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
>> +	if (!phy)
>> +		return -ENOMEM;
>> +
>> +	phy->regs = devm_platform_ioremap_resource(pdev, 0);
>> +	if (IS_ERR(phy->regs))
>> +		return PTR_ERR(phy->regs);
>> +
>> +	phy->phy = devm_phy_create(dev, NULL, &jh7110_pcie_phy_ops);
>> +	if (IS_ERR(phy->phy))
>> +		return dev_err_probe(dev, PTR_ERR(phy->regs),
>> +			"Failed to map phy base\n");
>> +
>> +	phy->sys_syscon =
>> +		syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
>> +						     "starfive,sys-syscon",
>> +						     1, args);
>> +
>> +	if (!IS_ERR_OR_NULL(phy->sys_syscon))
>> +		phy->sys_phy_connect = args[0];
>> +	else
>> +		phy->sys_syscon = NULL;
>> +
>> +	phy->stg_syscon =
>> +		syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
>> +						     "starfive,stg-syscon",
>> +						     2, args);
>> +
>> +	if (!IS_ERR_OR_NULL(phy->stg_syscon)) {
>> +		phy->stg_pcie_mode = args[0];
>> +		phy->stg_pcie_usb = args[1];
>> +	} else {
>> +		phy->stg_syscon = NULL;
>> +	}
>> +
>> +	platform_set_drvdata(pdev, phy);
>> +	phy_set_drvdata(phy->phy, phy);
>> +	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> +
>> +	return PTR_ERR_OR_ZERO(phy_provider);
>> +}
>> +
>> +static int jh7110_pcie_phy_remove(struct platform_device *pdev)
>> +{
>> +	platform_set_drvdata(pdev, NULL);
>> +
>> +	return 0;
>> +}
>> +
>> +static const struct of_device_id jh7110_pcie_phy_of_match[] = {
>> +	{ .compatible = "starfive,jh7110-pcie-phy" },
>> +	{ /* sentinel */ },
>> +};
>> +MODULE_DEVICE_TABLE(of, jh7110_pcie_phy_of_match);
>> +
>> +static struct platform_driver jh7110_pcie_phy_driver = {
>> +	.probe	= jh7110_pcie_phy_probe,
>> +	.remove	= jh7110_pcie_phy_remove,
>> +	.driver = {
>> +		.of_match_table	= jh7110_pcie_phy_of_match,
>> +		.name  = "jh7110-pcie-phy",
>> +	}
>> +};
>> +module_platform_driver(jh7110_pcie_phy_driver);
>> +
>> +MODULE_DESCRIPTION("StarFive JH7110 PCIe 2.0 PHY driver");
>> +MODULE_AUTHOR("Minda Chen <minda.chen@starfivetech.com>");
>> +MODULE_LICENSE("GPL");
> 
> cheers,
> -roger
diff mbox series

Patch

diff --git a/MAINTAINERS b/MAINTAINERS
index c09ea66dcd5a..8e0f755ba91b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19968,10 +19968,12 @@  M:	William Qiu <william.qiu@starfivetech.com>
 S:	Supported
 F:	Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
 
-STARFIVE JH71X0 USB PHY DRIVER
+STARFIVE JH71X0 PCIE AND USB PHY DRIVER
 M:	Minda Chen <minda.chen@starfivetech.com>
 S:	Supported
+F:	Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml
 F:	Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml
+F:	drivers/phy/starfive/phy-jh7110-pcie.c
 F:	drivers/phy/starfive/phy-jh7110-usb.c
 
 STATIC BRANCH/CALL
diff --git a/drivers/phy/starfive/Kconfig b/drivers/phy/starfive/Kconfig
index 2c013c390dee..c21c21d284a6 100644
--- a/drivers/phy/starfive/Kconfig
+++ b/drivers/phy/starfive/Kconfig
@@ -12,6 +12,17 @@  config PHY_STARFIVE_DPHY_RX
 	  system. If M is selected, the module will be called
 	  phy-starfive-dphy-rx.
 
+config PHY_STARFIVE_JH7110_PCIE
+	tristate "Starfive JH7110 PCIE 2.0/USB 3.0 PHY support"
+	depends on USB_SUPPORT
+	select GENERIC_PHY
+	select USB_PHY
+	help
+	  Enable this to support the StarFive PCIe 2.0 PHY,
+	  or used as USB 3.0 PHY.
+	  If M is selected, the module will be called
+	  phy-jh7110-pcie.ko.
+
 config PHY_STARFIVE_JH7110_USB
 	tristate "Starfive JH7110 USB 2.0 PHY support"
 	depends on USB_SUPPORT
diff --git a/drivers/phy/starfive/Makefile b/drivers/phy/starfive/Makefile
index 176443852f4d..03a55aad53a2 100644
--- a/drivers/phy/starfive/Makefile
+++ b/drivers/phy/starfive/Makefile
@@ -1,3 +1,4 @@ 
 # SPDX-License-Identifier: GPL-2.0
 obj-$(CONFIG_PHY_STARFIVE_DPHY_RX)      += phy-starfive-dphy-rx.o
+obj-$(CONFIG_PHY_STARFIVE_JH7110_PCIE)	+= phy-jh7110-pcie.o
 obj-$(CONFIG_PHY_STARFIVE_JH7110_USB)	+= phy-jh7110-usb.o
diff --git a/drivers/phy/starfive/phy-jh7110-pcie.c b/drivers/phy/starfive/phy-jh7110-pcie.c
new file mode 100644
index 000000000000..fe029daef62e
--- /dev/null
+++ b/drivers/phy/starfive/phy-jh7110-pcie.c
@@ -0,0 +1,202 @@ 
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * StarFive JH7110 PCIe 2.0 PHY driver
+ *
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ * Author: Minda Chen <minda.chen@starfivetech.com>
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/mfd/syscon.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#define PCIE_KVCO_LEVEL_OFF		(0x28)
+#define PCIE_USB3_PHY_PLL_CTL_OFF	(0x7c)
+#define PCIE_KVCO_TUNE_SIGNAL_OFF	(0x80)
+#define PCIE_USB3_PHY_ENABLE		BIT(4)
+#define PHY_KVCO_FINE_TUNE_LEVEL	0x91
+#define PHY_KVCO_FINE_TUNE_SIGNALS	0xc
+
+#define USB_PDRSTN_SPLIT		BIT(17)
+
+#define PCIE_PHY_MODE			BIT(20)
+#define PCIE_PHY_MODE_MASK		GENMASK(21, 20)
+#define PCIE_USB3_BUS_WIDTH_MASK	GENMASK(3, 2)
+#define PCIE_USB3_RATE_MASK		GENMASK(6, 5)
+#define PCIE_USB3_RX_STANDBY_MASK	BIT(7)
+#define PCIE_USB3_PHY_ENABLE		BIT(4)
+
+struct jh7110_pcie_phy {
+	struct phy *phy;
+	struct regmap *stg_syscon;
+	struct regmap *sys_syscon;
+	void __iomem *regs;
+	u32 sys_phy_connect;
+	u32 stg_pcie_mode;
+	u32 stg_pcie_usb;
+	enum phy_mode mode;
+};
+
+static int jh7110_usb3_mode_set(struct jh7110_pcie_phy *data)
+{
+	if (!data->stg_syscon || !data->sys_syscon) {
+		dev_info(&data->phy->dev, "don't support usb3 mode\n");
+		return -EINVAL;
+	}
+
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_mode,
+			   PCIE_PHY_MODE_MASK, PCIE_PHY_MODE);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+			   PCIE_USB3_BUS_WIDTH_MASK, 0);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+			   PCIE_USB3_RATE_MASK, 0);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+			   PCIE_USB3_RX_STANDBY_MASK, 0);
+	regmap_update_bits(data->stg_syscon, data->stg_pcie_usb,
+			   PCIE_USB3_PHY_ENABLE, PCIE_USB3_PHY_ENABLE);
+
+	/* Connect usb 3.0 phy mode */
+	regmap_update_bits(data->sys_syscon, data->sys_phy_connect,
+			   USB_PDRSTN_SPLIT, 0);
+
+	/* Configuare spread-spectrum mode: down-spread-spectrum */
+	writel(PCIE_USB3_PHY_ENABLE, data->regs + PCIE_USB3_PHY_PLL_CTL_OFF);
+
+	return 0;
+}
+
+static void jh7110_pcie_mode_set(struct jh7110_pcie_phy *phy)
+{
+	/* PCIe Multi-PHY PLL KVCO Gain fine tune settings: */
+	writel(PHY_KVCO_FINE_TUNE_LEVEL, phy->regs + PCIE_KVCO_LEVEL_OFF);
+	writel(PHY_KVCO_FINE_TUNE_SIGNALS, phy->regs + PCIE_KVCO_TUNE_SIGNAL_OFF);
+}
+
+static int jh7110_pcie_phy_set_mode(struct phy *_phy,
+				    enum phy_mode mode, int submode)
+{
+	struct jh7110_pcie_phy *phy = phy_get_drvdata(_phy);
+	int ret;
+
+	if (mode == phy->mode)
+		return 0;
+
+	switch (mode) {
+	case PHY_MODE_USB_HOST:
+	case PHY_MODE_USB_DEVICE:
+	case PHY_MODE_USB_OTG:
+		ret = jh7110_usb3_mode_set(phy);
+		if (ret)
+			return ret;
+		break;
+	case PHY_MODE_PCIE:
+		jh7110_pcie_mode_set(phy);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	dev_info(&_phy->dev, "Changing phy mode to %d\n", mode);
+	phy->mode = mode;
+
+	return 0;
+}
+
+static int jh7110_pcie_phy_init(struct phy *_phy)
+{
+	return 0;
+}
+
+static int jh7110_pcie_phy_exit(struct phy *_phy)
+{
+	return 0;
+}
+
+static const struct phy_ops jh7110_pcie_phy_ops = {
+	.init		= jh7110_pcie_phy_init,
+	.exit		= jh7110_pcie_phy_exit,
+	.set_mode	= jh7110_pcie_phy_set_mode,
+	.owner		= THIS_MODULE,
+};
+
+static int jh7110_pcie_phy_probe(struct platform_device *pdev)
+{
+	struct jh7110_pcie_phy *phy;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	u32 args[2];
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return -ENOMEM;
+
+	phy->regs = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(phy->regs))
+		return PTR_ERR(phy->regs);
+
+	phy->phy = devm_phy_create(dev, NULL, &jh7110_pcie_phy_ops);
+	if (IS_ERR(phy->phy))
+		return dev_err_probe(dev, PTR_ERR(phy->regs),
+			"Failed to map phy base\n");
+
+	phy->sys_syscon =
+		syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
+						     "starfive,sys-syscon",
+						     1, args);
+
+	if (!IS_ERR_OR_NULL(phy->sys_syscon))
+		phy->sys_phy_connect = args[0];
+	else
+		phy->sys_syscon = NULL;
+
+	phy->stg_syscon =
+		syscon_regmap_lookup_by_phandle_args(pdev->dev.of_node,
+						     "starfive,stg-syscon",
+						     2, args);
+
+	if (!IS_ERR_OR_NULL(phy->stg_syscon)) {
+		phy->stg_pcie_mode = args[0];
+		phy->stg_pcie_usb = args[1];
+	} else {
+		phy->stg_syscon = NULL;
+	}
+
+	platform_set_drvdata(pdev, phy);
+	phy_set_drvdata(phy->phy, phy);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static int jh7110_pcie_phy_remove(struct platform_device *pdev)
+{
+	platform_set_drvdata(pdev, NULL);
+
+	return 0;
+}
+
+static const struct of_device_id jh7110_pcie_phy_of_match[] = {
+	{ .compatible = "starfive,jh7110-pcie-phy" },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, jh7110_pcie_phy_of_match);
+
+static struct platform_driver jh7110_pcie_phy_driver = {
+	.probe	= jh7110_pcie_phy_probe,
+	.remove	= jh7110_pcie_phy_remove,
+	.driver = {
+		.of_match_table	= jh7110_pcie_phy_of_match,
+		.name  = "jh7110-pcie-phy",
+	}
+};
+module_platform_driver(jh7110_pcie_phy_driver);
+
+MODULE_DESCRIPTION("StarFive JH7110 PCIe 2.0 PHY driver");
+MODULE_AUTHOR("Minda Chen <minda.chen@starfivetech.com>");
+MODULE_LICENSE("GPL");